Device dictionary

Loading…

Reference ID	String
0	Model
1	.1f
2	4.2f
3	A000: Undefined
4	A001: EEPROM Error (CP)
5	A002: RAM Error (CP)
6	A003: No Sensor Response
7	A004: Temperature Overrange
8	A005: Mass Flow Rate Overrange
9	A006: Characterization Required
10	A007: Real-Time Interrupt Failure
11	A008: Density Overrange
12	A009: Transmitter Initializing/Warming Up
13	A010: Calibration Failure
14	A011: Zero Calibration Failed: Low
15	A012: Zero Calibration Failed: High
16	A013: Zero Calibration Failed: Unstable
17	A014: Transmitter Failure
18	A015: MA Readback Error
19	A016: Sensor RTD Failure
20	A017: T-Series RTD Failure
21	A018: EEPROM Error (Xmtr)
22	A019: RAM Error (Xmtr)
23	A020: No Flow Cal Value
24	A021: No K1 Value
25	A022: Config DB Corrupt (CP)
26	A023: Internal Totals Corrupt (CP)
27	A024: Program Corrupt (CP)
28	A025: Boot Sector Fault (CP)
29	A026: Sensor/Xmtr Comm Failure
30	A027: Security Breach
31	A028: CP Write Failure
32	A029: PIC/Daughterboard Comm Failure
33	A030: Incorrect Board Type
34	A031: Low Power
35	A032: SMV: Outputs Fixed
36	A033: No LPO/RPO Signal
37	A034: Smart Meter Verification Failed
38	A035: Smart Meter Verification Aborted
39	A036: Undefined
40	A037: Undefined
41	A038: Undefined
42	A039: Undefined
43	A100: MAO1 Saturated
44	A101: MAO1 Fixed
45	A102: Drive Overrange
46	A103: Data Loss Possible
47	A104: Calibration-In-Progress
48	A105: Two-Phase Flow
49	A106: Burst Mode Enabled
50	A107: Power Reset Occurred
51	A108: Single-SP Event 1 ON
52	A109: Single-SP Event 2 ON
53	A110: FO Saturated
54	A111: FO Fixed
55	A112: Upgrade Transmitter Software
56	A113: MAO2 Saturated
57	A114: MAO2 Fixed
58	A115: No External Data
59	A116: API: Temperature Overrange
60	A117: API: Density Overrange
61	A118: DO1 Fixed
62	A119: DO2 Fixed
63	A120: ED: Curve Fit Failure
64	A121: ED: Extrapolation Alert
65	A122: DO3 Fixed
66	A123: DO4 Fixed
67	A124: FI Saturated
68	A125: Batch Timeout
69	A126: Batch Overrun
70	A127: Batch No Reset
71	A128: Batch/Fill No Start
72	A129: PPI Display Error
73	A130: Printer Out of Paper
74	A131: SMV in Progress
75	A132: Sensor Simulation Active
76	A133: PIC UI EEPROM Error
77	A134: PPI Memory Error
78	A135: PPI Communication Error
79	A136: Undefined
80	A137: Undefined
81	A138: Undefined
82	A139: Undefined
83	D1 Calibration in Progress
84	D2 Calibration in Progress
85	D3 Calibration in Progress
86	D4 Calibration in Progress
87	FD Calibration in Progress
88	Zero Calibration in Progress
89	Temperature Slope Calibration in Progress
90	Temperature Offset Calibration in Progress
91	Discrete Event 1 Active
92	Discrete Event 2 Active
93	Discrete Event 3 Active
94	Discrete Event 4 Active
95	Discrete Event 5 Active
96	Discrete Output 1 Active
97	Discrete Output 2 Active
98	Discrete Output 3 Active
99	Discrete Input 1 Active
100	Discrete Input 2 Active
101	Flow Rate Switch Active
102	Undefined
103	Live Zero Flow Rate
104	Core Processor Input Voltage
105	Present MAO Gauge
106	Present Freq Gauge
107	Smart Meter Verification Results
108	Time in Seconds
109	Left and Right Pickoff Stiffness
110	%
111	mA Output Trim
112	Resets all totalizers.
113	Resets mass flow totalizer.
114	Resets volumne flow totalizer.
115	Read Modbus Data
116	Write Modbus Data
117	Smart Meter Verification
118	Starts Smart Meter Verification and shows the result PASS or FAIL. This procedure takes upto 4 minutes.
119	Most Recent Test Results
120	Configure the transmitter for sensor characteristics.
121	Configure channels, inputs, outputs, map variables, and communication settings.
122	Special Units
123	Configure the parameters required to convert an existing measurement unit to a different unit.
124	External Pressure/Temperature
125	Configure the transmitter to accept external input from polled pressure and/or temperature devices.
126	Configure the transmitter for gas standard volume measurement.
127	Map variables to the Primary Variable (PV), Secondary Variable (SV), Third Variable (TV), and Fourth Variable (QV).
128	No Additional Information for Above
129	Additional Information for Above
130	A032: Smart Meter Verification in Progress: Outputs Fixed
131	A104: Calibration in Progress
132	A131: Smart Meter Verification in Progress
133	Start
134	Turn Off Schedule
135	Turn off the Smart Meter Verification scheduler.
136	Setup
137	A034: Smart Meter Verification Failed
138	A035: Smart Meter Verification Aborted
139	LD Optimization
140	Configure the transmitter for LD optimization. LD optimization is used only with large sensors in hydrocarbon applications.
141	Show Last 20 Results
142	Device Reset
143	Restore Factory Configuration
144	A: Discrete Output 1 Fixed
145	Overview
146	Configure
147	Service Tools
148	All Totalizers
149	Variables
150	Primary Variable
151	Secondary Variable
152	Totalizers
153	Inputs/Outputs Fault Actions
154	Alert Severity
155	Mass Special Units
156	Volume Special Units
157	GSV
158	Identification
159	Revisions
160	Security and Simulation
161	mA Output Fault Settings
162	Manual Verification
163	Most Recent Test Results
164	Automatic Verification
165	F: EEPROM Error (CP)
166	F: RAM Error (CP)
167	F: No Sensor Response
168	F: Temperature Overrange
169	Additional Information
170	F: Mass Flow Overrange
171	View Diagnostic Variables
172	F: Characterization Required
173	F: Density Overrange
174	View Density Characterization
175	F: Transmitter Initializing/Warming Up
176	F: Calibration Failure
177	F: Zero Calibration Failed: Low
178	F: Zero Calibration Failed: High
179	F: Zero Calibration Failed: Unstable
180	F: Transmitter Failure
181	F: Sensor RTD Failure
182	F: T-Series RTD Failure
183	F: No Flow Calibration Value
184	F: No K1 Value
185	F: PIC/Daughterboard Communication Failure
186	F: Incorrect Board Type
187	F: Low Power
188	F: Outputs Fixed During Smart Meter Verification
189	F: No Right/Left Pickoff Signal
190	View Two-Phase Flow Condition
191	F: Smart Meter Verification Aborted
192	A: mA Output Saturated
193	A: mA Output Fixed
194	M: Drive Overrange
195	A: Calibration in Progress
196	M: Two-Phase Flow
197	A: Burst Mode Enabled
198	M: Power Reset Occurred
199	A: Frequency Output Saturated
200	A: Frequency Output Fixed
201	A: mA Output 2 Saturated
202	A: mA Output 2 Fixed
203	M: No External Input or Polled Data
204	M: Smart Meter Verification in Progress
205	A: Sensor Simulation Active
206	M: EEPROM Error (Display)
207	A: Discrete Event 1 Active
208	A: Discrete Event 2 Active
209	A: Discrete Event 3 Active
210	A: Discrete Event 4 Active
211	A: Discrete Event 5 Active
212	A: Discrete Input Active
213	M: Primary Variable Out of Limits
214	M: Non-Primary Variable Out of Limits
215	A: Cold Start
216	F: Field Device Malfunction
217	Zero
218	Electronics
219	Calibration
220	Reset/Restore
221	Offline Menu
222	Download
223	This process variable is the rate at which mass is flowing through the sensor.
224	.2f
225	.3f
226	.4f
227	.5f
228	8d
229	8.2f
230	8.3f
231	8.6f
232	Min Span
233	Mass Flow Classification
234	Mass Flow Family
235	Mass Flow PDQ
236	Mass Flow LS
237	Mass Flow Family Status
238	The temperature of the liquid or gas being measured.
239	Temperature Classification
240	Temperature Family
241	Temperature PDQ
242	Temperature LS
243	Temperature Family Status
244	Mass Total Classification
245	Mass Total Family
246	Mass Total PDQ
247	Mass Total LS
248	Mass Total Family Status
249	The density of the liquid being measured.
250	.6f
251	Density Classification
252	Density Family
253	Density PDQ
254	Density LS
255	Density Family Status
256	Mass Inventory Classification
257	Mass Inventory Family
258	Mass Inventory PDQ
259	Mass Inventory LS
260	Mass Inventory Family Status
261	This process variable is the rate at which volume is flowing through the sensor.
262	10.4f
263	Volume Flow Classification
264	Volume Flow Family
265	Volume Flow PDQ
266	Volume Flow LS
267	Volume Flow Family Status
268	Volume Total Classification
269	Volume Total Family
270	Volume Total PDQ
271	Volume Total LS
272	Volume Total Family Status
273	Volume Inventory Classification
274	Volume Inventory Family
275	Volume Inventory PDQ
276	Volume Inventory LS
277	Volume Inventory Family Status
278	Pressure Classification
279	Pressure Family
280	Pressure PDQ
281	Pressure LS
282	Pressure Family Status
283	6.2f
284	Drive Gain Upper Sensor Limit
285	Drive Gain Lower Sensor Limit
286	Drive Minimum Span
287	Drive Classification
288	Drive Family
289	Drive PDQ
290	Drive LS
291	Drive Family Status
292	External Temperature Classification
293	External Temperature Family
294	External Temperature PDQ
295	External Temperature LS
296	External Temperature Family Status
297	ANSI 150
298	ANSI 300
299	ANSI 600
300	PN40
301	JIS 10K
302	JIS 20K
303	ANSI 900
304	Sanitary clamp fitting
305	Union
306	PN100
307	Unknown
308	Tube Lining
309	PTFE
310	Tefzel
311	Tube Wetted Material
312	Hast-C
313	Monel
314	Tantalum
315	Titanium
316	316L SST
317	Inconel
318	Base Unit
319	Base Time
320	Forward
321	Reverse
322	Bi directional
323	A programmable high limit on density,which enables the transmitter to indicate two-phase flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed two-phase flow limits.
324	Two-Phase High Limit
325	5.4f
326	A programmable low limit on density, which enables the transmitter to indicate two-phase flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed two-phase flow limits.
327	Two-Phase Low Limit
328	A programmable time period,from 0.00 to 60.00 seconds,during which outputs representing flow hold their last measured value before indicating two-phase flow.
329	Two-Phase Duration
330	5.2f
331	Polarity
332	5d
333	5.3f
334	5.5f
335	µs
336	Standard deviation is the two sigma result from the number of zero samples taken during the last zero. 'Standard Deviation', 'Live Zero', 'Smart Zero Verification' and 'Field Verification Zero' can be used to see how stable the zero is on your meter.
337	6.5f
338	2d
339	Fault Action
340	Upscale (21.0-24.0 mA)
341	Downscale (1.0-3.6 mA)
342	Fault Action
343	Fault Action
344	Internal Zero - All 0
345	Internal Zero - Flow 0
346	Fault Level
347	Fault Level
348	1d
349	RTD Cable Resistance
350	T-Series RTD Resistance
351	Line RTD Resistance
352	Power On Time
353	Smart Meter Verification/Outputs in fault (A32)
354	Smart Meter Verification/Outputs at last value (A131)
355	7.2f
356	Passcode(4 Digits)
357	4d
358	Refresh Rate (100-10,000)
359	Poll as Primary Host
360	Poll as Secondary Host
361	Polled Variable 1
362	Polled Variable 2
363	10.7f
364	7.5f
365	Pressure Compensation
366	Disable
367	Enable
368	Compensation Pressure
369	This parameter allows you to enable/disable the external temperature feature.
370	This parameter allows you to enter a static temperature when using the external temperature feature.
371	Correction Temperature
372	The variable that is monitored to determine if a flow switch has occurred.
373	Smart Meter Verification Fail
374	The state to which the discrete output will be set if the transmitter detects a fault with 'Alert Severity' = 'Fault'. If 'None' is selected, the behavior of the discrete output will be controlled by 'Discrete Output Source'.
375	4.4f
376	Start Smart Meter Verification
377	Polarity
378	Discrete Input State
379	This parameter identifies the physical output channel to be configured. Channel 1 is terminals 1 and 2, and Channel 2 is terminals 3 and 4.
380	Assignment
381	Milliamp Output
382	Assignment
383	Power Source
384	Power Source
385	Tube Classification
386	Tube Family
387	Tube PDQ
388	Tube LS
389	Tube Family Status
390	Board Temperature Classification
391	Board Temperature Family
392	Board Temperature PDQ
393	Board Temperature LS
394	Board Temperature Family Status
395	Case Temperature Classification
396	Case Temperature Family
397	Case Temperature PDQ
398	Case Temperature LS
399	Case Temperature Family Status
400	Engineer to Order Number
401	Engineered to Order (ETO) number for the transmitter.
402	3d
403	Number of decimal points to be displayed for the value.
404	Disabled
405	Enabled
406	Gas Reference Density
407	Conversion Factor
408	Flow Label
409	Total Label
410	Specifies the lowest gas standard volume flow rate that will be reported as measured. All gas standard volume flow rates below this cutoff are reported as 0.
411	Simulate Primary Purpose Variables
412	The state of the overall simulation mode.
413	Control
414	Fixed Value
415	Ramp Low Point
416	Ramp High Point
417	Ramp Period
418	A standard volume flow rate measurement used when the process fluid is a gas.
419	Gas Volume Flow Classification
420	Gas Volume Flow Family
421	Gas Volume Flow PDQ
422	Gas Volume Flow LS
423	Gas Volume Flow Family Status
424	Gas Volume Total Classification
425	Gas Volume Total Family
426	Gas Volume Total PDQ
427	Gas Volume Total LS
428	Gas Volume Total Family Status
429	Gas Volume Inventory Classification
430	Gas Volume Inventory Family
431	Gas Volume Inventory PDQ
432	Gas Volume Inventory LS
433	Gas Volume Inventory Family Status
434	Live Zero Classification
435	Live Zero Family
436	Live Zero PDQ
437	Live Zero LS
438	Live Zero Family Status
439	Input Voltage Classification
440	Input Voltage Family
441	Input Voltage PDQ
442	Input Voltage LS
443	Input Voltage Family Status
444	Enable Smart Meter Verification
445	Specifies Smart Meter Verification enabling option
446	Background Smart Meter Verification
447	Ouput state during Smart Meter Verification
448	Specifies Ouput state during Smart Meter Verification
449	Uncertainty Limit
450	Stiffness limit set point for Smart Meter Verification
451	Reason for Abort
452	Indicates the number of times the Smart Meter Verification routine has successfully completed.
453	Smart Meter Verification Dataset Mean
454	Smart Meter Verification Dataset Satndard Deviation
455	Smart Meter Verification dataset LPO stiffness.
456	Smart Meter Verification dataset RPO stiffness.
457	Smart Meter Verification dataset damping.
458	Smart Meter Verification dataset LPO mass.
459	Smart Meter Verification dataset RPO mass.
460	Smart Meter Verification Dataset
461	The version of the Device Description (DD) being used.
462	Hours until Next Run
463	The number hours until the next time Smart Meter Verification runs.
464	4.1f
465	Hours between Recurring Runs (0=Schedule is not Repeating)
466	The number of hours between successive Smart Meter Verification runs. Valid range is 1 to 1000 hours or 0 for no recurring schedule.
467	Hours Remaining until Next Run
468	The number of hours remaining until Smart Meter Verification runs.
469	Smart Meter Verification Run Counter
470	The run counter for this Smart Meter Verification run.
471	Manual Abort
472	Watchdog Timeout
473	High Peak Drive Voltage
474	High Drive Current Standard Deviation
475	High Drive Current Mean Value
476	Drive Loop Reported Error
477	High Delta T Standard Deviation
478	High Delta T Value
479	State Running
480	Verification Complete
481	Wrong Verification Enable
482	No Factory Air Verification
483	No Factory Water Verification
484	Parameter Registers not Set
485	Transmitter Running Seconds at Test
486	Keep Existing Assignment
487	Initial Setup
488	Configures the sensor characteristics of the transmitter.
489	Configures channels, inputs, outputs and variable mapping.
490	Any changes made on this screen will be written to the device when the Next button is clicked. Transmitter operation could be affected. Click Next to write changes to the device, or click Cancel to abort.
491	The 'Milliamp Output' uses the 'Primary Variable' as its source.
492	The 'Secondary Variable' is only used in HART communications.
493	The 'Frequency Output' uses the 'Third Variable' as its source.
494	The 'Fourth Variable' is only used in HART communications.
495	Loop Tests
496	Set a fixed output value for the Milliamp Output.
497	Set a fixed output value for the Frequency Output.
498	Set a fixed output state for the Discrete Output.
499	Digital Communications
500	Enter an Alert number and change the Alert's severity to Fault, Information or Ignore.
501	Enter an Alert number and view the current severity of the alert.
502	Configures the process monitor screens by selecting the desired process variables for each screen.
503	Configures the number of decimal places for each process variable.
504	Assigns output channel type and variable.
505	Assigns a variable to the Milliamp Output, define Upper and Lower Range Values, Cutoff and Damping.
506	Assigns a variable to the Frequency Output, set Maximum Pulse Width, Polarity and Scaling.
507	Assigns a variable to the Discrete Output, set Flow Switch.
508	Assigns polarity to the Discrete Input.
509	Sets up Bell-202 port (HART only).
510	Assigns variables to Primary (PV), Secondary (SV), Third (TV) and Fourth (QV) Variables.
511	This screen will not automatically refresh after changing the 'Type' field. Select Guided Setup and then return to this screen to see the current configuration.
512	Optional Setup
513	Set Up Bell 202 Port
514	HART Burst Mode
515	Performs digital to analog trim of the Milliamp Output.
516	Performs first point (air) calibration.
517	Performs second point (water) calibration.
518	Performs third point (user's choice) calibration.
519	Performs fourth point (user's choice) calibration.
520	Performs flowing density calibration.
521	Status
522	Tag, model code, revision, security, and related data.
523	Displays values of process variables and outputs.
524	Trend charts for process and diagnostic variables.
525	Perform a zero calibration which sets a zero reference for a no-flow condition.
526	Revision Numbers
527	Security Switch Status
528	Simulation Status
529	Reads Modbus data from device memory.
530	Writes Modbus data to device memory.
531	Performs Smart Meter Verification, which will determine the health of the meter without stopping the process flow or removing the meter from the line.
532	Simulation Configuration
533	Mass Flow Rate Simulation Settings
534	Density Simulation Settings
535	Temperature Simulation Settings
536	Simulation Settings
537
538	Recommended Actions: 1. Check the sensor circuitry. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
539	Recommended Actions: 1. Verify that a sensor is connected to the transmitter. 2. Check the sensor RTD circuitry. 3. Verify that process temperature is within range of sensor and transmitter. 4. If the problem persists, contact Micro Motion.
540	Recommended Actions: 1. If other alerts are present (typically, A003, A006, A008, A102, or A105), resolve those alerts first. If the A005 alert persists, continue with the suggestions below. 2. View the diagnostic variables to verify whether tubes are vibrating. Left and Right pickoffs should be above 10mV. 3. Check the sensor circuitry. 4. Check the sensor tubes for erosion by verifying density. 5. If the problem persists, contact Micro Motion.
541	Recommended Actions: 1. Check the characterization. Specifically, verify the Flow FCF and K1 values on the sensor tag. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
542	Recommended Actions: 1. Check the characterization. Specifically, verify the FlowCal and K1 values on the sensor tag. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
543	The measured density has exceeded 0-10 g/Cucm.
544	Recommended Actions: 1. If other alerts are present (typically, A003, A006, A102, or A105), resolve those alerts first. If the A008 alert persists, continue with the suggestions below. 2. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes. 3. Check the sensor circuitry. 4. Verify density characterization and verify configuration matches sensor tag. 5 View diagnostic variables to verify raw tube frequency is in the proper range for the sensor type. 6. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 7. If the problem persists, contact Micro Motion.
545	Recommended Actions: 1. Allow the flowmeter to warm up (approximately 30 seconds). The error should disappear once the flowmeter is ready for normal operation. 2. Check the input voltage to ensure its between 12 and 15 V. 3. If alert does not clear, make sure that the sensor is completely full or completely empty. 4. Check the sensor circuitry. 5. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
546	Mechanical Zero: The resulting zero was greater than 3 microseconds. Temperature or Density Calibrations: Many possible causes.
547	Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter to clear the alert. 3. If appropriate, restore the factory zero to return the flowmeter to operation. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 5. If alert appears during a density calibration, contact Micro Motion.
548	Mechanical Zero: Calibration procedure failed due to reverse flow through the sensor.
549	Mechanical Zero: Calibration procedure failed due to reverse flow through the sensor. The resulting zero was greater than 3 microseconds.
550	Mechanical Zero: The resulting zero was greater than 3 microseconds.
551	Internal memory or program fault has been detected.
552	Recommended Actions: 1. Resolve other active alerts first. 2. Cycle power to the flowmeter. 3. If alert persists, the transmitter might need service. Contact Micro Motion.
553	Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 4. If the problem persists, contact Micro Motion.
554	Recommended Actions: 1. Check the characterization against the sensor tag. Specifically, verify the Flow FCF, K1 and K2 values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
555	Recommended Actions: 1. Check the characterization against the sensor tag. Specifically, verify the FlowCal, K1 and K2 values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
556	Recommended Actions: 1. If A017 is active, resolve it first. 2. Check the characterization against the sensor tag. Specifically, verify the Flow FCF, K1 and K2 values. 3. Check the sensor RTD circuitry. 4. If the problem persists, contact Micro Motion.
557	Recommended Actions: 1. Cycle power to the flowmeter. 2. If the problem persists, contact Micro Motion.
558	Recommended Actions: 1. Verify the core processor input voltage is at least 12V. 2. Check the power supply and all power wiring.
559	Smart Meter Verification is in progress, with outputs are fixed.
560	Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to continue measuring.
561	Recommended Actions: 1. Check for two-phase flow. 2. View the diagnostic variables to verify whether tubes are vibrating. Left and Right pickoffs should be above 10mV. 3. Check the sensor circuitry. 4. Check sensor tubes for plugging. 5. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 6. If the problem persists, contact Micro Motion.
562	Smart Meter Verification failed. The stiffness values not within acceptable limits.
563	Recommended Actions: 1. Immediately re-run the Smart Meter Verification test with outputs held at fault or last measured value. If the meter passes the second test, the fail result can be ignored. If the meter fails the second test, the flow tubes may be damaged. 2. Use the knowledge of your process to consider the type of damage and determine the appropriate action. These actions might include removing the meter from service and physically inspecting the tubes. At a minimum, perform a flow validation and a density calibration. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
564	Smart Meter Verification aborted.
565	Reason: User Initiated Abort Recommend Actions: 1. Wait for 15 seconds before starting Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
566	Reason: Frequency Drift Recommend Actions: 1. Ensure temperature, flow and density are stable and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
567	Reason: High Drive Gain Recommend Actions: 1. Ensure flow is steady and minimize entrained gas and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
568	Reason: Unstable Flow Recommend Actions: 1. Reduce flow rate and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
569	Reason: No Air Reference Recommend Actions: 1. Perform factory calibration on air. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
570	Reason: No Water Reference Recommend Actions: 1. Perform factory calibration on water. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
571	Reason: Missing Configuration Recommend Actions: 1. Load verification parameter registers with proper values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
572	Reason: Other Recommend Actions: 1. Run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If abort persists, contact Micro Motion.
573	Recommended Actions: 1. Verify that mA output range values are set to appropriate values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
574	Recommended Actions: 1. Check the HART address. If non-zero, set 'mA Output Action' parameter to enable 'Live mA Output' or if multi-drop mode is desired change the alert severity to ignore by going to the Configure-> Alert Setup-> Alert Severity screen. 2. If mA output trim is being performed, exit mA output trim. 3. If mA output loop test is being performed, exit mA output loop test. 4. Check to see if the output has been fixed via digital communications or the local display.
575	Recommended Actions: 1. Check the sensor circuitry. 2. If this is the only active alarm, it can be ignored. If desired, reconfigure the alarm severity to Ignore. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
576	Recommended Actions: 1. Allow the flowmeter to complete calibration. 2. For zero calibration procedures, you may abort the calibration, set the zero time parameter to a lower value, and restart the calibration. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
577	Recommended Actions: 1. Check that sensor is completely full. 2. Check that slug limits are set to appropriate values. 3. Verify density cutoff is at least 0.2 g/cc. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
578	Recommended Actions: 1. No action required. 2. If desired, reconfigure the alert severity to Ignore by going to the Configure-> Alert Setup-> Alert Severity screen.
579	Recommended Actions: 1. No action required. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
580	Process variable assigned to frequency output is outside configured scale limits.
581	Recommended Actions: 1. Change frequency output scaling factors to more appropriate settings. 2. If the Third Variable is set to volume flow, low density or empty tubes can cause the frequency output to saturate. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
582	Recommended Actions: 1. Exit frequency output loop test. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
583	Recommended Actions: 1. If mA output trim is being performed, exit mA output trim. 2. If mA output loop test is being performed, exit mA output loop test. 3. Check to see if the output has been fixed via digital communications or the local display. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
584	Recommended Actions: 1. Exit discrete output test. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
585	Recommended Actions: 1. HART polling connection to external device has failed. Ensure that external device is available. 2. Verify external device is not in fault. 3. Verify HART segment power, wiring and loop resistance. 4. Verify polling configuration in the transmitter and external device. 5. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
586	A131: Smart Meter Verification in Progress
587	Smart Meter Verification is in progress.
588	Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to fault. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
589	Recommended Actions: 1. Disable output simulation. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
590	Recommended Actions: 1. Cycle power to the flow meter. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. The flow meter might need service. Contact Micro Motion.
591	Recommended Actions: 1. Verify process and check for two-phase flow. 2. Check the diagnostic variables. 3. Check the sensor circuitry. 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
592	Recommended Actions: 1. Verify process and check for two-phase flow. 2. Check the test points. 3. Check the sensor circuitry. 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
593	Recommended Actions: 1. Check the HART address. If non-zero, set mA Output Action parameter to enable Live mA Output. 2. If mA output trim is being performed, exit mA output trim. 3. If mA output loop test is being performed, exit mA output loop test. 4. Check to see if the output has been fixed via digital communications or the local display.
594	Recommended Actions: 1. This is a summary alert and is generated when one of the fault severity alerts is active. Resolve the other active alerts first.
595	Density Characterization
596	Two-Phase Flow Condition
597	Electronic Conditions
598	Recommended Actions: 1. Cycle power to the flow meter. 2. The flow meter might need service. Contact Micro Motion.
599	Sensor Conditions
600	Process Conditions
601	Configuration Conditions
602	Recommended Actions: 1. If A26 also appears, resolve the A26 first if connected to core 700. 2. Allow the flowmeter to warm up (approximately 30 seconds). The error should disappear once the flowmeter is ready for normal operation. 3. Check the input voltage to ensure its between 12 and 15 V. 4. Check for proper voltage into the transmitter if connected to core 700. 5. If alert does not clear, make sure that the sensor is completely full or completely empty. 6. Check the sensor circuitry. 7. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
603	Recommended Actions: 1. Contact Micro Motion.
604	Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to last measured value.
605	Recommended Actions: 1. Smart Meter Verification aborted. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
606	Recommended Actions: 1. Allow the procedure to complete. You may abort the procedure if desired. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
607	Recommended Actions: 1. Verify that mA output range values are set to appropriate values.
608	Recommended Actions: 1. No action required.
609	Recommended Actions: 1. The first command to recognize this condition will automatically reset this flag. 2. This flag may also be set following a Master Reset or a Self Test.
610	Classic View
611	Performs a zero calibration.
612	Performs a density calibration.
613	Performs a temperature calibration.
614	Power cycles the device without affecting device configuration.
615	Overwrites the existing device configuration with the configuration set at the factory.
616	Resets the configuration changed flag if the host is not able to reset the flag automatically.
617	PV Analog Channel Saturated
618	PV Analog Channel Fixed
619	Enable on token-passing data link layer only
620	Enable on TDMA data link layer only
621	Enable on both TDMA and token-passing data link layer
622	Wireless
623	WirelessHART Device
624	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
625	Primary
626	Primary Analog Channel
627	Secondary
628	Secondary Analog Channel
629	Tertiary
630	Tertiary Analog Channel
631	Quaternary
632	Quaternary Analog Channel
633	Quinary
634	Quinary Analog Channel
635	Critical Power Failure
636	Lock all
637	Trim not supported
638	Configuration cannot be changed
639	Locked by gateway
640	Analog Input Channel
641	Analog Output Channel
642	Secondary Analog Channel Saturated
643	Tertiary Analog Channel Saturated
644	Quaternary Analog Channel Saturated
645	Quinary Analog Channel Saturated
646	Secondary Analog Channel Fixed
647	Tertiary Analog Channel Fixed
648	Quaternary Analog Channel Fixed
649	Quinary Analog Channel Fixed
650	Wired HART Enabled
651	Enabled on Wired HART device connection only
652	Wireless HART Enabled
653	Enabled on WirelessHART device connection only
654	Both Wired and WirelessHart Enabled
655	Enabled on both Wired and WirelessHART connections
656	8u
657	Device Variable
658	Analog Channel Number
659	Analog Channel Number- Index into an array of Analog Channels.
660	Burst Command
661	Changing configuration can affect transmitter operation. Ensure that the control loop is set for manual operation before continuing.
662	Enter 'Zero Time':
663	Flow must be zero. Click Next to perform a zero calibration.
664	A problem was detected:
665	It is now safe to return the control loop to automatic control.
666	Zero calibration is starting...
667	Calibration is in progress... Zero: %{0} µs Standard Deviation: %{1} µs
668	Auto Zero is complete. Zero: %{0} µs Standard Deviation: %{1} µs
669	Enter 'Density':
670	Calibration is in progress...
671	Density calibration is complete.
672	Note: Flow rate must be greater than 50% of the nominal flow for the meter.
673	Select 'Discrete Output State':
674	'Discrete Output State' is Off.
675	'Discrete Output State' is On.
676	Returning 'Discrete Output' to normal function...
677	Select 'Frequency Output' level:
678	10000 Hz;Other;End
679	Enter the desired 'Frequency Output':
680	'Frequency Output' is fixed at %0 Hz.
681	Select 'mA Output' level:
682	Output Value:
683	'mA Output' is fixed at %0 mA.
684	Connect the reference meter.
685	Click Next to set 'mA Output' to %0 mA.
686	Enter reading from the reference meter:
687	Does the device output match the reference meter?
688	Yes;No
689	All totalizers have been started.
690	All totalizers have been stopped.
691	All totalizers have been reset.
692	Mass total has been reset.
693	Volume total has been reset.
694	GSV total has been reset.
695	Returning 'Frequency Output' to normal function...
696	Returning 'mA Output' to normal function...
697	Note-Variables which use this as the units code will be in the previous units until this value is sent to the device.
698	alarmNum
699	Select Alert Severity:
700	Start Sensor Zero;Reset Mass Total;Reset Volume Total;Reset All Totals;Start/Stop Totals;Start Smart Meter Verification
701	Start Sensor Zero;Reset Mass Total;Reset Gas Standard Volume Total;Reset All Totals;Start/Stop Totals;Start Smart Meter Verification
702	None;Discrete Event 1;Discrete Event 2;Discrete Event 3;Discrete Event 4;Discrete Event 5
703	Start Sensor Zero;Reset Mass Total;Reset Volume Total;Reset All Totals;Start/Stop Totals
704	Start Sensor Zero;Reset Mass Total;Reset Gas Standard Volume Total;Reset All Totals;Start/Stop Totals
705	%0 is assigned to %1.
706	All alerts are acknowledged.
707	Selection for data type:
708	Enter 'Coil Number':
709	number
710	Enter 'Register Number':
711	'Coil Mode' is %0 and 'Exception Code' is %1.
712	'Unsigned 16 Value' is %0 and 'Exception Code' is %1.
713	'Unsigned 32 Value' is %0 and 'Exception Code' is %1.
714	'Floating Point Value' is %0 and 'Exception Code' is %1.
715	Coil Mode:
716	Disable;Enable
717	Enter 'Unsigned 16 Value':
718	uValue
719	Enter 'Unsigned 32 Value':
720	Enter 'Floating Point Value':
721	fValue
722	Select the 'Simulation Mode':
723	select
724	'Simulation Mode' is %0.
725	floatFaultVal
726	intLMVFaultTimeout
727	Starting Smart Meter Verification, please wait.
728	Smart Meter Verification completed: %{0} %
729	Smart Meter Verification PASSED. Meter meets factory specifications.
730	Smart Meter Verification FAILED. Meter may not meet factory specifications. Press Help for more Information.
731	Smart Meter Verification error.
732	Smart Meter Verification error. %{0}
733	Frequency Factor (Hz):
734	floatFreqVal
735	Rate Factor:
736	floatRateVal
737	Pulses/Unit:
738	floatPulsesPerUnit
739	Units/Pulse:
740	floatUnitsPerPulse
741	'Configuration Changed Flag' is being reset, please wait.
742	'Configuration Changed Flag' has been reset.
743	Mass Flow Rate: Value %0 %1 Gas Standard Volume Flow Rate: Value %2 %3 Density: Value %4 %5
744	Select Burst Mode:
745	Select Burst Option:
746	Burst Mode configuration completed.
747	Current sensor type selection is Other (Curved Tube). Select Sensor Type:
748	Current sensor type selection is T-Series (Straight Tube). Select Sensor Type:
749	Select 'Pressure Unit' used by the external pressure device:
750	Current primary variable selection is %0. Select Primary Variable:
751	View Alert Severity of:
752	Priority: Failed - Fix Now Description: An uncorrectable checksum mismatch has been detected. Recommended Actions: 1. Cycle power to the flow meter. 2. The flow meter might need service. Contact Micro Motion.
753	No Additional Information Available
754	Priority: Failed - Fix Now Description: ROM checksum error or a RAM location cannot be written to. Recommended Actions: 1. Cycle power to the flowmeter. 2. The flow meter might need service. Contact Micro Motion.
755	Priority: Failed - Fix Now Description: Continuity failure of drive circuit, LPO, or RPO, or LPO-RPO mismatch when driving. Recommended Actions: 1. Check the sensor circuitry. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
756	Drive Gain: Value %0
757	Priority: Failed - Fix Now Description: The value computed for the resistance of the line RTD or the Meter/Case RTD is outside limits. Recommended Actions: 1. Verify that a sensor is connected to the transmitter. 2. Check the sensor RTD circuitry. 3. Verify that process temperature is within range of sensor and transmitter. 4. If the problem persists, contact Micro Motion.
758	Temperature: Value %0
759	Priority: Failed - Fix Now Description: The measured flow has exceeded the maximum flow rate of the sensor. Recommended Actions: 1. If other alerts are present (typically, A003, A006, A008, A102, or A105), resolve those alerts first. If the A005 alert persists, continue with the suggestions below. 2. View the diagnostic variables to verify whether tubes are vibrating. Left and Right pickoffs should be above 10mV. 3. Check the sensor circuitry. 4. Check the sensor tubes for erosion by verifying density. 5. If the problem persists, contact Micro Motion.
760	Priority: Failed - Fix Now Description: One or more required characterization parameters have not been entered. Recommended Actions: 1. Check the characterization. Specifically, verify the FlowCal and K1 values on the sensor tag. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
761	Flow Cal: Value %0 K1: Value %1 uSec K2: Value %2 uSec
762	Priority: Failed - Fix Now Description: One or more required characterization parameters have not been entered. Recommended Actions: 1. Check the characterization. Specifically, verify the Flow FCF and K1 values on the sensor tag. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
763	Flow FCF: Value %0 K1: Value %1 uSec K2: Value %2 uSec
764	Priority: Failed - Fix Now Description: The measured density has exceeded 0-10 g/Cucm. Recommended Actions: 1. If other alerts are present (typically, A003, A006, A102, or A105), resolve those alerts first. If the A008 alert persists, continue with the suggestions below. 2. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes. 3. Check the sensor circuitry. 4. Verify density characterization and verify configuration matches sensor tag. 5 View diagnostic variables to verify raw tube frequency is in the proper range for the sensor type. 6. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 7. If the problem persists, contact Micro Motion.
765	Priority: Failed - Fix Now Description: Transmitter in power-up mode. Recommended Actions: 1. Allow the flowmeter to warm up (approximately 30 seconds). The error should disappear once the flowmeter is ready for normal operation. 2. Check the input voltage to ensure its between 12 and 15 V. 3. If alert does not clear, make sure that the sensor is completely full or completely empty. 4. Check the sensor circuitry. 5. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
766	Priority: Failed - Fix Now Description: Mechanical zero: The resulting zero was greater than 3 microseconds. Temperature or Density Calibrations: Many possible causes. Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter to clear the alert. 3. If appropriate, restore the factory zero to return the flowmeter to operation. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 5. If alert appears during a density calibration, contact Micro Motion.
767	Priority: Failed - Fix Now Description: Mechanical zero: Calibration procedure failed due to reverse flow through the sensor. Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter to clear the alert. 3. If appropriate, restore the factory zero to return the flowmeter to operation. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 5. If alert appears during a density calibration, contact Micro Motion.
768	Priority: Failed - Fix Now Description: Mechanical zero: Calibration procedure failed due to flow through the sensor.The resulting zero was greater than 3 microseconds. Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter to clear the alert. 3. If appropriate, restore the factory zero to return the flowmeter to operation. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 5. If alert appears during a density calibration, contact Micro Motion.
769	Priority: Failed - Fix Now Description: Mechanical zero: The resulting zero was greater than 3 microseconds. Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter to clear the alert. 3. If appropriate, restore the factory zero to return the flowmeter to operation. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 5. If alert appears during a density calibration, contact Micro Motion.
770	Priority: Failed - Fix Now Description: Internal memory or program fault has been detected. Recommended Actions: 1. Resolve other active alerts first. 2. Cycle power to the flowmeter. 3. If alert persists, the transmitter might need service. Contact Micro Motion.
771	Priority: Failed - Fix Now Description: The value computed for the resistance of the Line RTD is outside limits. Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 4. If the problem persists, contact Micro Motion.
772	Priority: Failed - Fix Now Description: The value computed for the resistance of the Meter/Case RTD is outside limits. Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 4. If the problem persists, contact Micro Motion.
773	Priority: Failed - Fix Now Description: The flow calibration factor and/or K1 has not been entered since the last master reset. Recommended Actions: 1. Check the characterization against the sensor tag. Specifically, verify the FlowCal, K1 and K2 values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
774	Priority: Failed - Fix Now Description: The flow calibration factor and/or K1 has not been entered since the last master reset. Recommended Actions: 1. Check the characterization against the sensor tag. Specifically, verify the Flow FCF, K1 and K2 values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If the problem persists, contact Micro Motion.
775	Priority: Failed - Fix Now Description: The sensor is recognized as a straight tube but the K1 value indicates a curved tube, or vice versa. Recommended Actions: 1. If A017 is active, resolve it first. 2. Check the characterization against the sensor tag. Specifically, verify the Flow FCF, K1 and K2 values. 3. Check the sensor RTD circuitry. 4. If the problem persists, contact Micro Motion.
776	Flow FCF: Value %0 K1: Value %1 us K2: Value %2 us
777	Priority: Failed - Fix Now Description: Transmitter electronics failure has occurred. Recommended Actions: 1. Cycle power to the flowmeter. 2. If the problem persists, contact Micro Motion.
778	Priority: Failed - Fix Now Description: The loaded software is not compatible with the programmed board type. Recommended Actions: 1. Contact Micro Motion.
779	Priority: Failed - Fix Now Description: The core processor is not receiving enough power. Recommended Actions: 1. Verify the core processor input voltage is at least 12V. 2. Check the power supply and all power wiring.
780	Priority: Failed - Fix Now Description: Smart Meter Verification is in progress, with outputs are fixed. Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to last measured value.
781	Priority: Failed - Fix Now Description: No signal from Left Pickoff or Right Pickoff, suggesting that sensor tubes are not vibrating. Recommended Actions: 1. Check for two-phase flow. 2. View the diagnostic variables to verify whether tubes are vibrating. Left and Right pickoffs should be above 10mV. 3. Check the sensor circuitry. 4. Check sensor tubes for plugging. 5. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 6. If the problem persists, contact Micro Motion.
782	Priority: Advisory Description: The calculated amount of current output is outside of the linear range. Recommended Actions: 1. Verify that mA output range values are set to appropriate values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
783	Primary Variable: %0 %0: Value %1 %2
784	PV LRV: Value %0 %1 PV URV: Value %2 %3
785	Priority: Advisory Description: Non-zero HART address configured, or user has set the mA output to a fixed value. Recommended Actions: 1. Check the HART address. If non-zero, set 'mA Output Action' parameter to enable 'Live mA Output' or if multi-drop mode is desired change the alert severity to ignore by going to the Configure-> Alert Setup-> Alert Severity screen. 2. If mA output trim is being performed, exit mA output trim. 3. If mA output loop test is being performed, exit mA output loop test. 4. Check to see if the output has been fixed via digital communications or the local display.
786	HART Address: %0 mAO Fault Action: %1
787	Priority: Maintenance - Fix Soon Description: The drive power (current/voltage) is at its maximum. Recommended Actions: 1. Check the sensor circuitry. 2. If this is the only active alarm, it can be ignored. If desired, reconfigure the alarm severity to Ignore. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
788	Priority: Advisory Description: A calibration procedure is in progress. Recommended Actions: 1. Allow the flowmeter to complete calibration. 2. For zero calibration procedures, you may abort the calibration, set the zero time parameter to a lower value, and restart the calibration. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
789	Priority: Maintenance - Fix Soon Description: The density has exceeded the user-defined slug (density) limits. Recommended Actions: 1. Check that sensor is completely full. 2. Check that slug limits are set to appropriate values. 3. Verify density cutoff is at least 0.2 g/cc. 4. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
790	Slug High Limit: Value %0 g/Cucm Slug Low Limit: Value %1 g/Cucm Slug Duration: Value %2 sec
791	Priority: Advisory Description: Device is in HART burst mode. Recommended Actions: 1. No action required. 2. If desired, reconfigure the alert severity to Ignore by going to the Configure-> Alert Setup-> Alert Severity screen.
792	Priority: Maintenance - Fix Soon Description: Transmitter has been restarted. Recommended Actions: 1. No action required. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
793	Priority: Advisory Description: Process variable assigned to frequency output is outside configured scale limits. Recommended Actions: 1. Change frequency output scaling factors to more appropriate settings. 2. If the Third Variable is set to volume flow, low density or empty tubes can cause the frequency output to saturate. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
794	Third Variable: %0 %0: Value %1 %2
795	Rate Factor: Value %0 Hz Pulses/Unit: Value %1 Units/Pulse: Value %2
796	Priority: Advisory Description: User has set the frequency output to a fixed value. Recommended Actions: 1. Exit frequency output loop test. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
797	Tube Frequency: Value %0 Hz
798	Priority: Advisory Description: Non-zero HART address configured, or user has set the mA output to a fixed value. Recommended Actions: 1. Check the HART address. If non-zero, set 'mA Output Action' parameter to enable 'Live mA Output' or if multi-drop mode is desired change the alert severity to ignore by going to the Configure-> Alert Setup-> Alert Severity screen. 2. If mA output trim is being performed, exit mA output trim. 3. If mA output loop test is being performed, exit mA output loop test. 4. Check to see if the output has been fixed via digital communications or the local display.
799	Priority: Maintenance - Fix Soon Description: No response received from polled device. Recommended Actions: 1. HART polling connection to external device has failed. Ensure that external device is available. 2. Verify device operation. 3. Verify wiring. 4. Verify polling configuration.
800	Poll Control: %0 Ext Device Tag 1: %1 Polled Variable 1: %2
801	Ext Device Tag 2: %0 Polled Variable 2: %1
802	Priority: Maintenance - Fix Soon Description: Smart Meter Verification is in progress. Recommended Actions: 1. Allow the procedure to complete. You may abort the procedure if desired. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
803	Priority: Advisory Description: Simulation mode is enabled. Recommended Actions: 1. Disable output simulation. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
804	Priority: Maintenance - Fix Soon Description: An uncorrectable checksum mismatch has been detected. Recommended Actions: 1. Cycle power to the flow meter. 2. The flow meter might need service. Contact Micro Motion.
805	Priority: Advisory Description: Discrete Event 1 has been triggered. Recommended Actions: 1. No action required.
806	Discrete Event Var: %0 Discrete Event Type: %1
807	Setpoint A: Value %0 Setpoint B: Value %1
808	Priority: Advisory Description: Discrete Event 2 has been triggered. Recommended Actions: 1. No action required.
809	Priority: Advisory Description: Discrete Event 3 has been triggered. Recommended Actions: 1. No action required.
810	Priority: Advisory Description: Discrete Event 4 has been triggered. Recommended Actions: 1. No action required.
811	Priority: Advisory Description: Discrete Event 5 has been triggered. Recommended Actions: 1. No action required.
812	Priority: Advisory Description: Discrete Input is active. Recommended Actions: 1. No action required.
813	Priority: Maintenance - Fix Soon Description: Primary variable has exceeded sensor limits. Recommended Actions: 1. Verify process and check for two-phase flow. 2. Check the diagnostic variables. 3. Check the sensor circuitry 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
814	Priority: Maintenance - Fix Soon Description: Non-primary variable has exceeded sensor limits. Recommended Actions: 1. Verify process and check for two-phase flow. 2. Check the diagnostic variables. 3. Check the sensor circuitry 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
815	Priority: Maintenance - Fix Soon Description: The calculated amount of current output is outside of the linear range. Recommended Actions: 1. Verify that mA output range values are set to appropriate values.
816	Priority: Maintenance - Fix Soon Description: Non-zero HART address configured, or user has set the mA output to a fixed value. Recommended Actions: 1. Check the HART address. If non-zero, set mA Output Action parameter to enable Live mA Output. 2. If mA output trim is being performed, exit mA output trim. 3. If mA output loop test is being performed, exit mA output loop test. 4. Check to see if the output has been fixed via digital communications or the local display.
817	Priority: Advisory Description: Power has been removed and reapplied resulting in the reinstallations of the setup information. Recommended Actions: 1. The first command to recognize this condition will automatically reset this flag. 2. This flag may also be set following a Master Reset or a Self Test.
818	Priority: Maintenance - Fix Soon Description: A write or set command has been executed. Recommended Actions: 1. No action required.
819	Priority: Failed - Fix Now Description: A hardware error or failure has been detected by the device. Recommended Actions: 1. This is a summary alert and is generated when one of the fault severity alerts is active. Resolve the other active alerts first.
820	Factory zero has been restored.
821	Smart Meter Verification will hold outputs at last value for about 2 minutes. Press Next to Start or Cancel to End.
822	Smart Meter Verification will hold outputs at fault value for about 2 minutes. Press Next to Start or Cancel to End.
823	Smart Meter Verification in progress: %{intSMVprogress}% complete
824	Smart Meter Verification FAILED. Meter may not meet factory specifications. Recommended Action: Run Smart Meter Verification with outputs held at last measured value or fault.
825	Smart Meter Verification FAILED. Meter may not meet factory specifications. Recommended Action: Immediately re-run the Smart Meter Verification test. If the meter passes the second test, the fail result can be ignored. If the meter fails the second test, the flow tubes may be damaged and should be investigated.
826	Smart Meter Verification ABORTED. Reason: %{0} Recommended Action: Wait for 15 seconds before starting Smart Meter Verification again.
827	The device is write protected, switch off the 'Security Switch' to disable write protection mode.
828	Aborting due to field device error.
829	Smart Meter Verification schedule is turned off.
830	Can't abort verification,Smart Meter Verification already complete.
831	Smart Meter Verification ABORTED. Reason: User Initiated Abort Recommended Action: Wait for 15 seconds before starting Smart Meter Verification again.
832	Uploading Smart Meter Verification results from the device. This will take a few minutes. Uploading progress (19 total) : %{0}
833	For Hours between Recurring Runs, valid range is 1 to 1000 hours or 0 for no recurring schedule. Please enter again.
834	Uploading results data from device. This will take a few minutes.
835	Test Result #%{Datalog_Index} Run Number: %0 Result: %1 Abort Code: %2 Time in Seconds: %3
836	Priority: Failed - Fix Now Description: Smart Meter Verification failed. The stiffness values not within acceptable limits. Recommended Actions: 1. Immediately re-run the Smart Meter Verification test with outputs held at fault or last measured value. If the meter passes the second test, the fail result can be ignored. If the meter fails the second test, the flow tubes may be damaged. 2. Use the knowledge of your process to consider the type of damage and determine the appropriate action. These actions might include removing the meter from service and physically inspecting the tubes. At a minimum, perform a flow validation and a density calibration. 3. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
837	Smart Meter Verification Run Counter: %0 Transmitter Running Hours at Test: %1 Left Pickoff Stiffness: %2
838	Right Pickoff Stiffness: %0
839	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: User Initiated Abort Recommend Actions: 1. Wait for 15 seconds before starting Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
840	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: Frequency Drift Recommend Actions: 1. Ensure temperature, flow and density are stable and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
841	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: High Drive Gain Recommend Actions: 1. Ensure flow is steady and minimize entrained gas and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
842	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: Unstable Flow Recommend Actions: 1. Reduce flow rate and run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
843	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: No Air Reference Recommend Actions: 1. Perform factory calibration on air. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
844	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: No Water Reference Recommend Actions: 1. Perform factory calibration on water. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
845	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: Missing Configuration Recommend Actions: 1. Load verification parameter registers with proper values. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
846	Priority: Failed - Fix Now Description: Smart Meter Verification aborted. Reason: Other Recommend Actions: 1. Run Smart Meter Verification again. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen. 3. If abort persists, contact Micro Motion.
847	Smart Meter Verification Run Counter: %0 Transmitter Running Hours at Test: %1 Abort Code: %2
848	Left Pickoff Stiffness: %0 Right Pickoff Stiffness: %1
849	LD Optimization is %0.
850	LD Optimization:
851	Next
852	select1
853	Select Alert Number:
854	Current severity is %0.
855	%{1} is set to %{0}.
856	A001: EEPROM Error (CP) is set to %0.
857	A002: RAM Error (CP) is set to %0.
858	A003: No Sensor Response is set to %0.
859	A004: Temperature Overrange is set to %0.
860	A005: Mass Flow Rate Overrange is set to %0.
861	A006: Characterization Required is set to %0.
862	A008: Density Overrange is set to %0.
863	A009: Transmitter Initializing Warming Up is set to %0.
864	A010: Calibration Failure is set to %0.
865	A011: Zero Calibration Failed: Low is set to %0.
866	A012: Zero Calibration Failed: High is set to %0.
867	A013: Zero Calibration Failed: Unstable is set to %0.
868	A014: Transmitter Failure is set to %0.
869	A016: Sensor RTD Failure is set to %0.
870	A017: T-Series RTD Failure is set to %0.
871	A020: No Flow Cal Value is set to %0.
872	A021: No K1 Value is set to %0.
873	A029: PIC Daughterboard Comm Failure is set to %0.
874	A030: Incorrect Board Type is set to %0.
875	A031: Low Power is set to %0.
876	A032: SMV: Outputs Fixed is set to %0.
877	A033: No LPO RPO Signal is set to %0.
878	A034: Smart Meter Verification Failed is set to %0.
879	A035: Smart Meter Verification Aborted is set to %0.
880	A100: MAO1 Saturated is set to %0.
881	A101: MAO1 Fixed is set to %0.
882	A102: Drive Overrange is set to %0.
883	A103: Data Loss Possible is set to %0.
884	A104: Calibration-In-Progress is set to %0.
885	A105: Two-Phase Flow is set to %0.
886	A106: Burst Mode Enabled is set to %0.
887	A107: Power Reset Occurred is set to %0.
888	A110: FO Saturated is set to %0.
889	A111: FO Fixed is set to %0.
890	A115: No External Data is set to %0.
891	A118: DO1 Fixed is set to %0.
892	A131: SMV in progress is set to %0.
893	A132: Sensor Simulation Active is set to %0.
894	Access Restricted
895	Device is being reset, please wait.
896	Device reset completed successfully.
897	You are about to overwrite the device configuration with factory values. Before continuing, set the control loop for manual operation and ensure that existing configuration values are documented or saved to a file. If the device connection is lost, reconnect using the defaults. Proceed?
898	Factory values were restored successfully.
899	Priority: Advisory The user has set the discrete output to a fixed state. Recommended Actions: 1. Exit discrete output test. 2. If you want to change the alert severity, go to the Configure-> Alert Setup-> Alert Severity screen.
Reference ID	String