Loading…
Loading…
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |
|---|---|---|---|---|---|
| before_poll | 4000 | Before polling | msrc_UNKNOWN | 详细信息 | |
| put_in_manual | 4065 | Loop in manual | msrc_UNKNOWN | 详细信息 | |
| back_to_normal | 4066 | Back to normal | msrc_UNKNOWN | 详细信息 | |
| write_protect_on | 4049 | Write protect | Write protects the device, if correct password is entered | msrc_UNKNOWN | 详细信息 |
| write_protect_off | 404A | Write enable | Write enables the device, if correct password is previously entered | msrc_UNKNOWN | 详细信息 |
| set_new_password | 404B | New password | Sets a new password for write protection, if correct password is entered | msrc_UNKNOWN | 详细信息 |
| show_serial_number | 4060 | Serial Number | 9 digit production line serial number, consisting of yybbbrrrr, where <yy> is the year of production, <bbb> is the batch number and <rrrr> is a running number for this batch. Expanded from device id | msrc_UNKNOWN | 详细信息 |
| enter_sensor_configuration | 404C | Sensor config | Configures the sensor, sensor type, measurement type, CJC compensation etc. | msrc_UNKNOWN | 详细信息 |
| enter_cable_resistance | 404E | Enter value | Enter new value for cable resistance. If the device setup is RTD/Ohm 3 or 4 wire, cable resistance for sensor 1 is the expected max value for the total cable resistance in 2 wires. Otherwise it is the actual total cable resistance for the selected sensor | msrc_UNKNOWN | 详细信息 |
| measure_cable_resistance | 404F | Measure value | Automaticly measures the cable resistance. If the device setup is RTD/Ohm 3 or 4 wire, cable resistance for sensor 1 is the expected max value for the total cable resistance in 2 wires. Otherwise it is the actual total cable resistance for the selected sensor | msrc_UNKNOWN | 详细信息 |
| restore_configuration | 4067 | restoring configuration | msrc_UNKNOWN | 详细信息 | |
| broken_namur_down | 405C | NAMUR down | Enables broken sensor error detection, and sets the error output value to 3.5 mA acc. to NAMUR NE43 | msrc_UNKNOWN | 详细信息 |
| broken_namur_up | 405D | NAMUR up | Enables broken sensor error detection, and sets the error output value to 23 mA acc. to NAMUR NE43 | msrc_UNKNOWN | 详细信息 |
| shorted_namur_down | 405E | NAMUR down | Enables shorted sensor error detection, and sets the error output value to 3.5 mA acc. to NAMUR NE43 | msrc_UNKNOWN | 详细信息 |
| shorted_namur_up | 405F | NAMUR up | Enables shorted sensor error detection, and sets the error output value to 23 mA acc. to NAMUR NE43 | msrc_UNKNOWN | 详细信息 |
| override_dac_trim | 4048 | Override D/A trim | Overrides any previously D/A trimming by restoring factory calibration values | msrc_UNKNOWN | 详细信息 |
| transmitter_loop_test | 1023 | 回路测试 | 回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。 | msrc_UNKNOWN | 详细信息 |
| transmitter_dac_trim | 1024 | D/A修正 | 数字到模拟修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。 | msrc_UNKNOWN | 详细信息 |
| leave_fixed_current_mode | 1003 | 退出固定电流模式 | 退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。 | msrc_UNKNOWN | 详细信息 |
| return_to_normal | 1016 | 中止返回正常 | msrc_UNKNOWN | 详细信息 | |
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |