Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| before_poll | 4000 | Before polling | msrc_UNKNOWN | Details | |
| put_in_manual | 4065 | Loop in manual | msrc_UNKNOWN | Details | |
| back_to_normal | 4066 | Back to normal | msrc_UNKNOWN | Details | |
| write_protect_on | 4049 | Write protect | Write protects the device, if correct password is entered | msrc_UNKNOWN | Details |
| write_protect_off | 404A | Write enable | Write enables the device, if correct password is previously entered | msrc_UNKNOWN | Details |
| set_new_password | 404B | New password | Sets a new password for write protection, if correct password is entered | msrc_UNKNOWN | Details |
| show_serial_number | 4060 | Serial Number | 9 digit production line serial number, consisting of yybbbrrrr, where <yy> is the year of production, <bbb> is the batch number and <rrrr> is a running number for this batch. Expanded from device id | msrc_UNKNOWN | Details |
| enter_sensor_configuration | 404C | Sensor config | Configures the sensor, sensor type, measurement type, CJC compensation etc. | msrc_UNKNOWN | Details |
| enter_cable_resistance | 404E | Enter value | Enter new value for cable resistance. If the device setup is RTD/Ohm 3 or 4 wire, cable resistance for sensor 1 is the expected max value for the total cable resistance in 2 wires. Otherwise it is the actual total cable resistance for the selected sensor | msrc_UNKNOWN | Details |
| measure_cable_resistance | 404F | Measure value | Automaticly measures the cable resistance. If the device setup is RTD/Ohm 3 or 4 wire, cable resistance for sensor 1 is the expected max value for the total cable resistance in 2 wires. Otherwise it is the actual total cable resistance for the selected sensor | msrc_UNKNOWN | Details |
| restore_configuration | 4067 | restoring configuration | msrc_UNKNOWN | Details | |
| broken_namur_down | 405C | NAMUR down | Enables broken sensor error detection, and sets the error output value to 3.5 mA acc. to NAMUR NE43 | msrc_UNKNOWN | Details |
| broken_namur_up | 405D | NAMUR up | Enables broken sensor error detection, and sets the error output value to 23 mA acc. to NAMUR NE43 | msrc_UNKNOWN | Details |
| shorted_namur_down | 405E | NAMUR down | Enables shorted sensor error detection, and sets the error output value to 3.5 mA acc. to NAMUR NE43 | msrc_UNKNOWN | Details |
| shorted_namur_up | 405F | NAMUR up | Enables shorted sensor error detection, and sets the error output value to 23 mA acc. to NAMUR NE43 | msrc_UNKNOWN | Details |
| override_dac_trim | 4048 | Override D/A trim | Overrides any previously D/A trimming by restoring factory calibration values | msrc_UNKNOWN | Details |
| transmitter_loop_test | 1023 | Messkreistest | Meßkreistest- ermöglicht es, den Analogausgang manuell auf einen gewünschten konstanten Wert einzustellen | msrc_UNKNOWN | Details |
| transmitter_dac_trim | 1024 | D/A Abgleich | Digital zu Analog Abgleich- Ermöglicht den Abgleich der Endpunkten des gewählten Analogausgangs mit einer externen Referenz | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | Fest-Stromausgang beenden | Konstantstrom Modus verlassen- Der Analogausgang war auf einen bestimmten Ausgangswert eingefroren. Es erfolgt die Rückkehr zu der Betriebsart, bei der der Analogausgang wieder dem Prozeßwert folgt | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | Abbruch Rückk. zu normal | msrc_UNKNOWN | Details | |
| Name | ID | Label | Description | Type | Source |