Loading…
Loading…
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |
|---|---|---|---|---|---|
| zero_trim_at_zero | 4045 | 归零修正 | Zero trim - Make the sensor input the new zero input reference. Sensor gain trim point is adjusted. | msrc_UNKNOWN | 详细信息 |
| sv_upper_trim | 4047 | Temp upper trim | msrc_UNKNOWN | 详细信息 | |
| sv_lower_trim | 4046 | Temp low trim | msrc_UNKNOWN | 详细信息 | |
| transmitter_self_test | 400A | Self test | msrc_UNKNOWN | 详细信息 | |
| master_reset | 400B | Master reset | msrc_UNKNOWN | 详细信息 | |
| reset_flag | 4007 | Reset config chgd | Resets the configuration changed flag | msrc_UNKNOWN | 详细信息 |
| write_protect_contrl | 401E | Write prtct cntrl | Changes the write protect setting of the transmitter | msrc_UNKNOWN | 详细信息 |
| comp_mode_toggle | 403A | Comp mode on/off | Turns on/off digital compensation of input errors. | msrc_UNKNOWN | 详细信息 |
| toggle_pv_damping | 4040 | Damp mode on/off | Turns on/off damping of input | msrc_UNKNOWN | 详细信息 |
| select_alarm_code | 4019 | Select alarm code | This command performs the function of setting the PV Analog Output Current Failure Alarm mode of the device to allow a prespecified current condition upon a hardware failure condition as indicated by an over pressure condition, sensor malfunction or other condition requiring notification to the analog control system | msrc_UNKNOWN | 详细信息 |
| restore_settings | 4009 | Restr fctry set | This command will restore all original factory settings to the slave device. It will destroy, by overwriting, any user calibration, notes, messages, tags, or other modifications which have been entered into the slave device by the user | msrc_UNKNOWN | 详细信息 |
| return_to_normal | 1016 | 中止返回正常 | msrc_UNKNOWN | 详细信息 | |
| warning_message | 1017 | 设置回路为手动 | msrc_UNKNOWN | 详细信息 | |
| loop_test | 1002 | 回路测试 | 回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。 | msrc_UNKNOWN | 详细信息 |
| dac_trim | 1004 | D/A修正 | 数字到模拟修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。 | msrc_UNKNOWN | 详细信息 |
| zero_trim | 1006 | Zero calibrate | Zero calibrate - Make the sensor input the new zero input reference. Sensor gain trim point is not adjusted. | msrc_UNKNOWN | 详细信息 |
| leave_fixed_current_mode | 1003 | 退出固定电流模式 | 退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。 | msrc_UNKNOWN | 详细信息 |
| applied_rerange | 1007 | 应用数值 | 应用值——通过将需要的上限值和下限值应用至设备输入对设备执行重新排列。 | msrc_UNKNOWN | 详细信息 |
| sensor_a_upper_sensor_trim | 1789 | Gain trim | Pressure Sensor Upper Trim- Calibrate the pressure sensor. | msrc_UNKNOWN | 详细信息 |
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |