Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| zero_trim_at_zero | 4045 | ｾﾞﾛ ﾄﾘﾑ | Zero trim - Make the sensor input the new zero input reference. Sensor gain trim point is adjusted. | msrc_UNKNOWN | Details |
| sv_upper_trim | 4047 | Temp upper trim | msrc_UNKNOWN | Details | |
| sv_lower_trim | 4046 | Temp low trim | msrc_UNKNOWN | Details | |
| transmitter_self_test | 400A | Self test | msrc_UNKNOWN | Details | |
| master_reset | 400B | Master reset | msrc_UNKNOWN | Details | |
| reset_flag | 4007 | Reset config chgd | Resets the configuration changed flag | msrc_UNKNOWN | Details |
| write_protect_contrl | 401E | Write prtct cntrl | Changes the write protect setting of the transmitter | msrc_UNKNOWN | Details |
| comp_mode_toggle | 403A | Comp mode on/off | Turns on/off digital compensation of input errors. | msrc_UNKNOWN | Details |
| toggle_pv_damping | 4040 | Damp mode on/off | Turns on/off damping of input | msrc_UNKNOWN | Details |
| select_alarm_code | 4019 | Select alarm code | This command performs the function of setting the PV Analog Output Current Failure Alarm mode of the device to allow a prespecified current condition upon a hardware failure condition as indicated by an over pressure condition, sensor malfunction or other condition requiring notification to the analog control system | msrc_UNKNOWN | Details |
| restore_settings | 4009 | Restr fctry set | This command will restore all original factory settings to the slave device. It will destroy, by overwriting, any user calibration, notes, messages, tags, or other modifications which have been entered into the slave device by the user | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| warning_message | 1017 | ﾙｰﾌﾟをﾏﾆｭｱﾙにします | msrc_UNKNOWN | Details | |
| loop_test | 1002 | ﾙｰﾌﾟ ﾃｽﾄ | ﾙｰﾌﾟ ﾃｽﾄ - ｱﾅﾛｸﾞ出力をﾕｰｻﾞｰが選択した値で固定出力します | msrc_UNKNOWN | Details |
| dac_trim | 1004 | D/A ﾄﾘﾑ | D/A ﾄﾘﾑ (ﾃﾞｼﾞﾀﾙ/ｱﾅﾛｸﾞ ﾄﾘﾑ) - ｵﾍﾟﾚｰﾃｨﾝｸﾞ ｴﾝﾄﾞ ﾎﾟｲﾝﾄに対するｱﾅﾛｸﾞ出力と外部指示計とのｷｬﾘﾌﾞﾚｰｼｮﾝを行います。 | msrc_UNKNOWN | Details |
| zero_trim | 1006 | Zero calibrate | Zero calibrate - Make the sensor input the new zero input reference. Sensor gain trim point is not adjusted. | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | 固定電流ﾓｰﾄﾞを終ります | 現在の固定ﾓｰﾄﾞを終了 - ｱﾅﾛｸﾞ出力を定数値のﾓｰﾄﾞから移行させ, 出力が入力に応じて変わるﾓｰﾄﾞに戻します。 | msrc_UNKNOWN | Details |
| applied_rerange | 1007 | 実入力 | 実入力 - 機器のﾚﾝｼﾞ変換を Upper ﾚﾝｼﾞ値と Lower ﾚﾝｼﾞ値の実際の入力で行います。 | msrc_UNKNOWN | Details |
| sensor_a_upper_sensor_trim | 1789 | Gain trim | Pressure Sensor Upper Trim- Calibrate the pressure sensor. | msrc_UNKNOWN | Details |
| Name | ID | Label | Description | Type | Source |