方法列表 - Magnetrol - Model TA2 2.x-00E1

Loading…

名称	ID	标签	描述	类型	源代码
Refresh_History_table	41A7	View History	Displays current status and run time as well as a history of most recent faults and warnings. For each event, the run time when the event occurred and the duration of the event are shown. The run time is the time since power up or a history reset. The table of history events displays the most recent event at the top with successively preceding events in descending order.	msrc_UNKNOWN	详细信息
HistReset_method	41AA	Reset History	Clears entries in Status History and resets the run time to zero.	msrc_UNKNOWN	详细信息
RTD_Calibration	4233	Calibrate RTDs	Use this function to calibrate the probe RTDs for the temperature and flow measurements. The probe tip must be submerged in a constant temperature water bath. A separate accurate temperature reading device must be used to determine the actual water bath temperature. An inaccurate calibration temperature entry will result in performance that is out of specification or a non-functional unit.	msrc_UNKNOWN	详细信息
exit_rtd_cal	423B	Exit RTD Cal		msrc_UNKNOWN	详细信息
Heater_Calibration	423A	Calibrate Heater	Use this menu to calibrate the PWM settings for the heater current control. An accurate ammeter must be connected in series with the heater wiring. When prompted, enter the value of the current displayed on the ammeter. Press 'Save' to store the present setting. After the actual currents corresponding to the 50 mA and 200 mA settings are saved, the device will compute the heater slope and intercept. The device will report the results of the calibration as the Heater Calibration parameter. An inaccurate heater calibration entry will result in performance that is out of specification or a non-functional unit.	msrc_UNKNOWN	详细信息
exit_htr_cal	423C	Exit Heater Cal		msrc_UNKNOWN	详细信息
Zero_Power_Test	4226	Zero Power Test	This test checks that the resistances of the temperature sensors have not changed. The test should be performed either in a water bath or under flowing conditions. During the test, the heater drive current is shut off. The measured ambient temperature should match the actual ambient temperature. See the TA2 Installation and Operations Manual for other details of the test.	msrc_UNKNOWN	详细信息
Low_Cal_Validation	4227	Low Cal Validation	This procedure validates the heat transfer characteristics of the sensor under low flow conditions. Perform the test at room temperature with the sensor supported vertically. A shroud should be placed around the sensor tip to isolate the tip from air currents. The shroud should not be tight against the sensor tip. During the test, the heater drive current is set to a pre-set value. The measured Delta T temperature (the temperature difference between the two pins) is measured and compared against a stored value. See the TA2 Installation and Operations Manual for other details of the test including recommended comparison between the measured and stored values.	msrc_UNKNOWN	详细信息
High_Cal_Validation	4228	High Cal Validation	This procedure validates the heat transfer characteristics of the sensor under high flow conditions. Perform the test in room temperature water with the sensor supported vertically. The sensor must be completely covered and the water must be kept still. During the test, the heater drive current is set to a pre-set value. The measured Delta T temperature (the temperature difference between the two pins) is measured and compared against a stored value. See the TA2 Installation and Operations Manual for other details of the test including recommended comparison between the measured and stored values.	msrc_UNKNOWN	详细信息
exit_probe_check	423D	Exit Probe Check		msrc_UNKNOWN	详细信息
PulseOutTest	422A	Test Pulse		msrc_UNKNOWN	详细信息
exit_pulse_test	4242	Exit Pulse Test		msrc_UNKNOWN	详细信息
TempReset_method	422D	Reset Temperatures	Reset the maximum and minimum temperatures measured for the electronics to the present temperature.	msrc_UNKNOWN	详细信息
ProcessTempReset_method	422C	Reset Temperatures	Reset the maximum process temperature measured at the probe to the present temperature.	msrc_UNKNOWN	详细信息
TotalizerReset_method	419C	Reset Totalizer	Reset Totalizer - Resets the totalizer and elapsed time to 0.	msrc_UNKNOWN	详细信息
exit_fixed_htr	422B	Exit Fixed Signal		msrc_UNKNOWN	详细信息
loop2_test	4229	AO2 Loop Test	Loop test- Allows the User to manually manipulate the Analog Output to a selected constant output value.	msrc_UNKNOWN	详细信息
loop2_dac_trim	41A2	D/A Trim AO2	Digital to Analog Trim- Allows the calibration of a selected Analog Output with an external reference at the operating endpoints of the Analog Output.	msrc_UNKNOWN	详细信息
leave_fixed_current_mode2	4298	退出固定电流模式	退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。	msrc_UNKNOWN	详细信息
reset_config_changed	4222	Reset Config Chgd	Resets the Configuration Changed bit in the Device Status	msrc_UNKNOWN	详细信息
dac_trim	1004	D/A Trim AO1	数字到模拟修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。	msrc_UNKNOWN	详细信息
loop_test	1002	AO1 Loop Test	回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。	msrc_UNKNOWN	详细信息
return_to_normal	1016	中止返回正常		msrc_UNKNOWN	详细信息
leave_fixed_current_mode	1003	退出固定电流模式	退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。	msrc_UNKNOWN	详细信息
warning_message	1017	设置回路为手动		msrc_UNKNOWN	详细信息
名称	ID	标签	描述	类型	源代码