方法列表 - GE Masoneilan - SVi1000-00CC

Loading…

名称	ID	标签	描述	类型	源代码
methodReadSlot	4042	Select the slot	To load the tuning parameters stored in the specific slot	msrc_UNKNOWN	详细信息
post_method_fill_100	40B7	fill		msrc_UNKNOWN	详细信息
methodShowFirmwareVersion	4062	Firmware Version	Display the firmware version.	msrc_UNKNOWN	详细信息
methodChangeMode	4003	Change Mode	Change mode: Changes the mode to Normal Mode, Manual Mode, or Setup Mode. Normal Mode: The position setpoint follows the input signal. Always return to Normal Mode to return to Control by the Control System. Manual Mode: The position setpoint remains at the last position prior to entering Manual Mode. Position setpoint may adjusted with the local pushbuttons or by HART commands. Setup Mode: The position setpoint remains at the last position prior to entering Setup Mode. Use this mode to change configuration and calibration information.	msrc_UNKNOWN	详细信息
methodFindStops	401D	Find Stops	Run automatic find stops will establish the calibration position of the valve at actuator pressure vented and at full supply pressure.	msrc_UNKNOWN	详细信息
methodAutoTune	4021	Autotune	Run PID Autotune will automatically find best dynamic parameters for responsive valve positioning. Always isolate the valve from the process. The valve will move full open and full closed. The valve will continuously change position for about 5 minutes. To SVi1000 device, this operation need the device should be set PID selector to slot 0/ATO or slot 8/ATC	msrc_UNKNOWN	详细信息
methodSetupWizard	400A	Setup Wizard	The setup wizard will guide you through basic steps to setup the positioner on an actuator. You may skip this wizard if the valve and positioner have been factory configured and calibrated. Always isolate the valve from the process. The wizard allows setting Air Action. The valve move full open and full closed. You will be prompted if mode must be changed. The steps are in the following order: 1. Run Find Stops, to set 0% to the valve closed position and to set 100% to full opened position. 2. Run Auto Tune to determine best dynamic parameters for position control. 3. Reset Basic Configuration and Calibration to Factory Defaults.	msrc_UNKNOWN	详细信息
methodFactoryConfiguration	4025	Reset Basic Config and Cal To Defaults	The Reset to Factory Default will set the following list of configuration and calibration parameters to defaults: The PID tunning parameters in slot 0 are set to defaults; Input current range is set to 4 to 20 mA; Open stop adjustment is set to 100%; Position error parameters are reset and disabled; Bumpless transfer is disabled; Position limits are disabled; Position rate limits are disabled; Tight shutoff is set to 0 and enabled; Characterization is set to linear;	msrc_UNKNOWN	详细信息
methodReadFaults	4027	Current Faults	Read the current faults of device.	msrc_UNKNOWN	详细信息
methodReadClearFaults	4005	Read/Clear Faults	Read the device's current faults. Optionally, the fault status may also be cleared.	msrc_UNKNOWN	详细信息
methodClearFaults	4028	Clear Current Faults	Clear the current device status/faults	msrc_UNKNOWN	详细信息
methodReadHistoricFaults	4029	Historical Faults	Read the historical faults of device.	msrc_UNKNOWN	详细信息
methodClearHistoricFaults	402A	Clear All Faults	Clear the historic and current device faults/status.	msrc_UNKNOWN	详细信息
methodManualSetpoint	4004	Set Position	Set manual valve setpoint in % or set the position by equivalent input current to simulate non-linear characterization and limits.	msrc_UNKNOWN	详细信息
methodFullyOpen	4023	Full Open	Fully Open valve	msrc_UNKNOWN	详细信息
methodFullyClose	4024	Full Closed	Fully Close Valve	msrc_UNKNOWN	详细信息
methodConfigureWizard	40C6	Configure Wizard	Change configuration of Tight shutoff.	msrc_UNKNOWN	详细信息
methodCharacterization	406A	Custom / Standard Characterization	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVi1000 positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.	msrc_UNKNOWN	详细信息
methodManualStop	401E	Manual Stops	This method is used to set manual stops.	msrc_UNKNOWN	详细信息
methodOpenStopAdj	4020	Open Stop Adjustment	Open stop adjustment; Allows to adjust travel to less than mechanical limits. Must be between 60% and 100% of mechanical travel set with Find Stops.	msrc_UNKNOWN	详细信息
methodTuning	4022	Manual Tuning	The user can set tuning PID parameters for slot 0, even though the current selector was selected for the other slot. To SVi1000 device, The only slot 0 PID parameters can be updated.	msrc_UNKNOWN	详细信息
restore_original_PIDs	40C8	abort restore		msrc_UNKNOWN	详细信息
methodSetIPCount	403A	Set I/P Output	Set IP Value. A value of 0 resets the device to allow the control task to set the I/P (changing modes or a reset also switches back to normal control modes).	msrc_UNKNOWN	详细信息
methodCalibSignal	4026	Input crnt snsr.	To calibrate or to check the 4-20mA current sensor.	msrc_UNKNOWN	详细信息
methodResetCalibrationData	4016	Reset Cal Factory Defaults	Reset Calibration Data: This will restore all sensor calibration data to factory defaults. If calibrations have been performed they will be lost!	msrc_UNKNOWN	详细信息
methodResetContinuous	41B1	Reset Historian	Reset valve historian data (stroke count, cycle count, time open, time closed and time near closed ) to 0. The previous data is lost and must be recorded to be used later.	msrc_UNKNOWN	详细信息
methodReset	4010	Reset SVi1000	This function performs a master reset to the device, causing it to go through its startup routine and re-initializing all of its operating parameters from non volatile memory.	msrc_UNKNOWN	详细信息
range_error_warning	40D5	Range error warning		msrc_UNKNOWN	详细信息
methodInterruptProcessNoModeChange	40BB	Stop Procedure		msrc_UNKNOWN	详细信息
methodRestoreAONormal	41BB			msrc_UNKNOWN	详细信息
methodSetAnalogOutput	41B4	Set Analog Output	User can set a fixed analog output of the position retransmitter.This is used only for checking loop wiring. Select Finished to return to position measurement function.	msrc_UNKNOWN	详细信息
methodChangeOutputRange	41B5	Re-transmitter Range	User can enter the upper and lower range values of valve position corresponding to output current 4 and 20 mA. The values typically are 0 and 100 %.	msrc_UNKNOWN	详细信息
method_serial_number	41BD	Read Device S/N	Read device and terminal board serial number.	msrc_UNKNOWN	详细信息
save_position_limits_value	40EF	save current parameters	save current parameters	msrc_UNKNOWN	详细信息
set_position_limits	406F	Set Position Limits	Set the valve position low/high limits	msrc_UNKNOWN	详细信息
pos_limit_check_method	40F0	Check signal range	Check signal range.	msrc_UNKNOWN	详细信息
save_signal_range_value	4102	save current parameters	save current parameters	msrc_UNKNOWN	详细信息
signal_range_check_method	4103	Check signal range	Check signal range.	msrc_UNKNOWN	详细信息
set_signal_range	401C	Set the signal range	Set the low/high input signal	msrc_UNKNOWN	详细信息
mthdReadCustomCharacterizationData	4148	Read Custom Characterization Data	Select characterization. If Custom is selected then continue to set custom points.	msrc_UNKNOWN	详细信息
methodCurrentMode	41A1	What is Current Mode?	What is Current Mode? - To get the current mode of this device	msrc_UNKNOWN	详细信息
mthdCheckCharacterizationData	4149	Edit	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVi1000 positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.	msrc_UNKNOWN	详细信息
名称	ID	标签	描述	类型	源代码