Device dictionary

Loading…

Reference ID	String
0	EPROM Checksum: Replace Transmitter or Replace Transmitter
1	RAM Error: Replace Transmitter
2	Debug, IRQ: Inform Dräger Fax: +49-451-882-2042
3	Cmd 48, Byte 0, Bit 0x10 Set
4	Cmd 48, Byte 0, Bit 0x08 Set
5	Debug, com1: Inform Dräger Fax: +49-451-882-2042
6	Debug, com2: Inform Dräger Fax: +49-451-882-2042
7	Cmd 48, Byte 0, Bit 0x01 Set
8	No sensorConnect sensor or Check sensor for electrolyte leakage: Resistance between pins 3<->6 shall be > 10MOhms or Replace Sensor or Replace Transmitter
9	Invalid sensor typeUse only sensors intended for Polytron2
10	Invalid sensor versionUse only sensors intended for Polytron2 or Replace Transmitter
11	Wrong sensor installedInstall Senser with correct Part No. or disable Sensor Lock temporarily
12	Wrong Gas Database
13	Invalid EEPROM versionPerform Standard Initialization or Perform Fundamental Initialization or Calibrate analog interface or Replace Transmitter
14	Cmd 48, Byte 1, Bit 0x02 Set
15	Cmd 48, Byte 1, Bit 0x01 Set
16	I2C-bus error during sensor data uploadReplace Sensor or Replace Transmitter
17	No valid sensor data read blockReplace Sensor or Replace Transmitter
18	No valid sensor data notice blockReplace Sensor or Replace Transmitter
19	No valid sensor data write blockReplace Sensor or Replace Transmitter
20	Checksum of gas name table corruptedInterrupt supply voltage > 1 sec (Reset)
21	Cmd 48, Byte 2, Bit 0x04 Set
22	Cmd 48, Byte 2, Bit 0x02 Set
23	Cmd 48, Byte 2, Bit 0x01 Set
24	Manufacturer database corruptedReplace Transmitter
25	EEPROM database corruptedPerform Fundamental Initialization or Calibrate analog interface
26	I2C-bus error during sensor data downloadInterrupt supply voltage > 1 sec (Reset)
27	Sensor stack 1 ErrorInform Dräger Fax: +49-451-882-2042
28	Sensor stack 2 ErrorInform Dräger Fax: +49-451-882-2042
29	HC11 Stack 1: Inform Dräger Fax: +49-451-882-2042
30	HC11 Stack 2: Inform Dräger Fax: +49-451-882-2042
31	Cmd 48, Byte 3, Bit 0x01 Set
32	Cmd 48, Byte 4, Bit 0x80 Set
33	Cmd 48, Byte 4, Bit 0x40 Set
34	Cmd 48, Byte 4, Bit 0x20 Set
35	Analog Database Checksum: Interrupt supply voltage > 1 sec (Reset)
36	Install test failedCheck supply voltage
37	Warning Parameters corrupted: Inform Dräger Fax: +49-451-882-2042
38	Invalid Supply Voltage: Check supply voltage
39	Invalid Loop Current: Check supply voltage; Calibrate analog interface or Replace Transmitter
40	Cmd 48, Byte 5, Bit 0x80 Set
41	Cmd 48, Byte 5, Bit 0x40 Set
42	Cmd 48, Byte 5, Bit 0x20 Set
43	Cmd 48, Byte 5, Bit 0x10 Set
44	Cmd 48, Byte 5, Bit 0x08 Set
45	Cmd 48, Byte 5, Bit 0x04 Set
46	Cmd 48, Byte 5, Bit 0x02 Set
47	Cmd 48, Byte 5, Bit 0x01 Set
48	No valid span calibrationCalibrate Sensor (zero) and Calibrate Sensor (span)
49	No valid zero calibrationCalibrate Sensor (zero)
50	No write access to sensor database during calibrationInterrupt supply voltage > 1 sec (Reset) and Calibrate Sensor (zero) and Calibrate Sensor (span) or Replace Sensor or Replace Transmitter
51	Cmd 48, Byte 14, Bit 0x10 Set
52	Too negative concentrationClean ambient from gasses with negative cross sensitivity or Calibrate Sensor (zero)
53	Sensor failed self testReplace Sensor
54	Sensor potential incompatibleUse only sensors intended for Polytron2
55	Cmd 48, Byte 14, Bit 0x01 Set
56	Debug measurement 1 ErrorInform Dräger Fax: +49-451-882-2042
57	Debug ADC 1 ErrorInform Dräger Fax: +49-451-882-2042
58	Debug ADC 2 ErrorInform Dräger Fax: +49-451-882-2042
59	Incorrect sensor potentialCheck supply voltage or Replace Transmitter
60	Pre-Amplifier Offset ErrorReplace Transmitter
61	Pre-Amplifier power consumption ErrorReplace Transmitter
62	Debug measurement 3 ErrorInform Dräger Fax: +49-451-882-2042
63	ADC overflowReplace Transmitter or Interrupt supply voltage > 1 sec (Reset)
64	ADC timing ErrorInform Dräger Fax: +49-451-882-2042
65	Cmd 48, Byte 16, Bit 0x20 Set
66	ADC common mode ErrorCheck supply voltage or Replace Transmitter
67	ADC span ErrorCheck supply voltage or Replace Transmitter
68	ADC zero ErrorCheck supply voltage or Replace Transmitter
69	HC11 ADC span ErrorCheck supply voltage or Replace Transmitter
70	HC11 ADC zero ErrorCheck supply voltage or Replace Transmitter
71	Cmd 48, Byte 17, Bit 0x80 Set
72	Cmd 48, Byte 17, Bit 0x40 Set
73	Cmd 48, Byte 17, Bit 0x20 Set
74	Cmd 48, Byte 17, Bit 0x10 Set
75	Cmd 48, Byte 17, Bit 0x08 Set
76	Cmd 48, Byte 17, Bit 0x04 Set
77	Cmd 48, Byte 17, Bit 0x02 Set
78	Cmd 48, Byte 17, Bit 0x01 Set
79	Cmd 48, Byte 18, Bit 0x80 Set
80	Cmd 48, Byte 18, Bit 0x40 Set
81	Cmd 48, Byte 18, Bit 0x20 Set
82	Cmd 48, Byte 18, Bit 0x10 Set
83	Cmd 48, Byte 18, Bit 0x08 Set
84	ADC invalid paramtersInform Dräger Fax: +49-451-882-2042
85	ADC time outInform Dräger Fax: +49-451-882-2042
86	ADC overrunInform Dräger Fax: +49-451-882-2042
87	Analog span not calibrated: Calibrate analog interface
88	Analog zero not calibrated: Calibrate analog interface
89	Cmd 48, Byte 22, Bit 0x20 Set
90	Cmd 48, Byte 22, Bit 0x10 Set
91	Cmd 48, Byte 22, Bit 0x08 Set
92	Date not programmedSet Clock
93	Time not programmedSet Clock
94	Clock back-up supply downSet Jumper X3 or replace Li-battery or Replace Transmitter
95	Cmd 48, Byte 23, Bit 0x80 Set
96	Cmd 48, Byte 23, Bit 0x40 Set
97	Sensor warm-up, no measurement: Wait for sensor to warm up
98	Sensor warm-up, Measurement error <4x spec.: Wait for sensor to warm up
99	Sensor counter electrode voltage out of rangeStop non permissable permanent gassing or Replace Sensor or Replace Transmitter or Replace Transmitter
100	Gas concentration is too highReduce gas concentration or Replace Sensor
101	Sensor temperature too lowAdjust ambient temperature to permissable range or Replace Sensor or Replace Transmitter
102	Sensor temperature too highAdjust ambient temperature to permissable range or Replace Sensor or Replace Transmitter
103	End of sensor life due to exposureReplace Sensor
104	End of sensor life due to poor sensitivityReplace Sensor
105	Cmd 48, Byte 24, Bit 0x20 Set
106	Cmd 48, Byte 24, Bit 0x10 Set
107	Too high exposure since last (span) calibrationCalibrate Sensor (zero) and Calibrate Sensor (span)
108	Calibration interval expiredCalibrate Sensor (zero) and Calibrate Sensor (span)
109	Gas concentration was too highCalibrate Sensor (zero) and Calibrate Sensor (span)
110	Sensor temperature was too highCalibrate Sensor (zero) and Calibrate Sensor (span)
111	.1f
112	.2f
113	8.2f
114	5.2f
115	4.2f
116	Upload Var List
117	4d
118	2d
119	AlmMinMax
120	RangeRef
121	.3f
122	02X
123	7d
124	8.1f
125	8.3f
126	d
127	3d
128	2x
129	p2GasIndex
130	p2Units1
131	p2Units2
132	p2Units3
133	p2Units4
134	p2Units5
135	p2Units6
136	p2Units7
137	p2Units8
138	p2Units9
139	p2Units10
140	p2Units11
141	p2Units12
142	p2Units13
143	p2Units14
144	p2Units15
145	p2Units16
146	p2Units17
147	p2Units18
148	p2Units19
149	p2Units20
150	p2Units21
151	p2Units22
152	p2Units23
153	p2Units24
154	p2Units25
155	p2Units26
156	p2Units27
157	p2Units28
158	p2Units29
159	p2Units30
160	p2Units31
161	p2UnitIndex
162	8u
163	Panic: Unknown Bit Cmd 48, Byte 19, 0x10
164	Panic: Unknown Bit Cmd 48, Byte 21, 0x10
165	Panic: Unknown Bit Cmd 48, Byte 21, 0x08
166	Panic: Unknown Bit Cmd 48, Byte 21, 0x04
167	Panic: Unknown Bit Cmd 48, Byte 21, 0x02
168	Panic: Unknown Bit Cmd 48, Byte 21, 0x01
169	SetupErrorCfg
170	WrapErrorCfg
171	EnterParamMode
172	ExitParamMode
173	EnterGasConfig
174	ExitGasConfig
175	Unexpected Error Command %{cmd}
176	The handheld will temporarily loose communication with the Polytron. Please Select "Online" to Reconnect
177	Online Info
178	Mode %{1} %{2} %{3} Online Info %{4} %{5} %{6} %{7} %{8} %{14} %{9} %{10} %{11} %{12} %{13} %{15} %{16}
179	Master Reset
180	Master Reset - Performs a master reset of the field device. Equivalent to cycling the transmitter power supply
181	MaintPasswd=%{0} Change Password?
182	Enter Maintenance Password
183	Entering Parameter Configuration Mode
184	Saving Password
185	Entering Measurement Mode
186	ConfigPasswd=%{0} Change Password?
187	Enter Configuration Password
188	Disable Warning Signal?
189	Disabling Analog Warning Signal
190	Enable Warning Signal?
191	N/A! Multidrop
192	Device is in Mutidrop; Analog Warning Signal is NOT Applicable
193	Device is in Mutidrop; Analog Warning Signal is NOT Applicable
194	Output Set to: %{2} %{1}
195	Use Special Signal
196	Fault;Warning;Maintenance
197	Enable Alarms
198	TestGas= %{0} MaxConc= %{3} %{1} Enter Actual Conc
199	Value Stabilized? %{2} %0 %{1}
200	Value OK? %{2} %{0} %{1}
201	Yes;No
202	Not doing the calibration
203	Too many write attempts
204	Remove Test Gas
205	Is Value out of Alarm Range? %{2} %0 %{1}
206	History Buffer %{4} %{5} %{6} %{7} %{8} %{14} %{9} %{10} %{11} %{12} %{13} %{15} %{16} Reset History?
207	MeasGas= %{0} Units= %{1} Change Gas/Units?
208	ExitGasSelect
209	Exiting from Gas Selection (selection mode not active)
210	Gas/Units NOT changed
211	TestGas= %{0} Units= %{1} Change Test Gas or Units?
212	ExitCalGasSelect
213	Exiting from Cal Gas Selection (selection mode not active)
214	Cal Gas and Units NOT changed
215	ExitReloadDB
216	Exiting from Cal Gas Selection (Reload DB)
217	Reloading Measurement Gas DB
218	Upload Timeout. Continue Upload?
219	Bad DB Upload. Retry Upload?
220	Offline
221	p2GasInfoArray
222	Warning; Some relays still active: Alarm 1: %{2} Alarm 2: %{1} ErrorRelay: %{0}
223	Sensor ready in %{0} Minutes Calibration possible in %{1} Minutes
224	4mA;20mA;Other mA;End
225	Output Set to: %{2} %{1}
226	Set Output Level Again?
227	Yes;No
228	Fault;Warning;Maintenance;End
229	About to Reset Error History
230	Error History is reset
231	Warning: SEND will fail while HMI Active. Please Correct
232	Reloading Measurement Gas DB
233	Upload Timeout. Continue Upload?
234	Entering Measurement Mode
Reference ID	String