方法列表 - GE Masoneilan - SVI II AP-00CA

Loading…

名称	ID	标签	描述	类型	源代码
post_method_fill_100	4141	fill		msrc_UNKNOWN	详细信息
methodShowFirmwareVersion	4086	Firmware Version	Display the firmware version.	msrc_UNKNOWN	详细信息
methodChangeMode	4011	Change Mode	Change mode: Changes the mode to Normal Mode, Manual Mode, or Setup Mode. Normal Mode: The position setpoint follows the input signal. Always return to Normal Mode to return to Control by the Control System. Manual Mode: The position setpoint remains at the last position prior to entering Manual Mode. Position setpoint may adjusted with the local pushbuttons or by HART commands. Setup Mode: The position setpoint remains at the last position prior to entering Setup Mode. Use this mode to change configuration and calibration information.	msrc_UNKNOWN	详细信息
methodFindStops	4032	Find Stops	Run automatic find stops will establish the calibration position of the valve at actuator pressure vented and at full supply pressure.	msrc_UNKNOWN	详细信息
methodAutoTune	4035	Autotune	Run PID Autotune will automatically find best dynamic parameters for responsive valve positioning. Always isolate the valve from the process. The valve will move full open and full closed. The valve will continuously change position for about 5 minutes.	msrc_UNKNOWN	详细信息
methodSetupWizard	4019	Setup Wizard	The setup wizard will guide you through basic steps to setup the positioner on an actuator. You may skip this wizard if the valve and positioner have been factory configured and calibrated. Always isolate the valve from the process. The wizard allows setting Air Action. The valve move full open and full closed. You will be prompted if mode must be changed. The steps are in the following order: 1. Set Air action to Air to Open or Air to Close; 2. Run Find Stops, to set 0% to the valve closed position and to set 100% to full opened position. 3. Run Auto Tune to determine best dynamic parameters for position control. 4. Reset Basic Configuration and Calibration to Factory Defaults.	msrc_UNKNOWN	详细信息
methodFactoryConfiguration	4039	Reset Basic Config and Cal To Defaults	The Reset to Factory Default will set the following list of configuration and calibration parameters to defaults: Air Action is set to ATO; All PID tuning parameters are set to defaults; Input current range is set to 4 to 20 mA; Open stop adjustment is set to 100%; Position error parameters are reset and disabled; Bumpless transfer is disabled; Position limits are disabled; Tight shutoff is set to 0.5% and enabled; Characterization is set to linear; Pressure units and language are set to psi and English; Button Locks = None; Controller = None;	msrc_UNKNOWN	详细信息
methodReadFaults	403F	Current Faults	Read the device's current faults.	msrc_UNKNOWN	详细信息
methodReadClearFaults	4013	Read/Clear Faults	Read the device's current faults. Optionally, the fault status may also be cleared.	msrc_UNKNOWN	详细信息
methodClearFaults	4040	Clear Current Faults	Clear the current device status/faults	msrc_UNKNOWN	详细信息
methodReadHistoricFaults	4041	Historical Faults	Read the device's historical faults.	msrc_UNKNOWN	详细信息
methodClearHistoricFaults	4042	Clear All Faults	Clear the historic and current device faults/status.	msrc_UNKNOWN	详细信息
methodManualSetpoint	4012	Set Position	Set manual valve setpoint in % or set the position by equivalent input current to simulate non-linear characterization and limits.	msrc_UNKNOWN	详细信息
methodFullyOpen	4037	Full Open	Fully Open valve	msrc_UNKNOWN	详细信息
methodFullyClose	4038	Full Close	Fully Close Valve	msrc_UNKNOWN	详细信息
methodConfigureWizard	403A	Configure Wizard	Change configuration of Limit Override, Tight shutoff, Pressure units, Language, Button Locks, Air Action, and Near Closed Value. Limit Overrideallows Find Stops, Autotune and Diagnostics to override position limits.	msrc_UNKNOWN	详细信息
methodCharacterization	408F	Custom / Standard Characterization	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVI2AP positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.	msrc_UNKNOWN	详细信息
methodRestoreAONormal	4134			msrc_UNKNOWN	详细信息
methodSetAnalogOutput	4030	Set Analog Output	User can set a fixed analog output of the position retransmitter.This is used only for checking loop wiring. Select Finished to return to position measurement function.	msrc_UNKNOWN	详细信息
methodChangeOutputRange	4031	Re-transmitter Range	User can enter the upper and lower range values of valve position corresponding to output current 4 and 20 mA. The values typically are 0 and 100 %.	msrc_UNKNOWN	详细信息
methodManualStop	4034	Manual Stops	This method is used to set manual stops.	msrc_UNKNOWN	详细信息
methodOpenStopAdj	4033	Open Stop Adjustment	Open stop adjustment; Allows to adjust travel to less than mechanical limits. Must be between 60% and 100% of mechanical travel set with Find Stops.	msrc_UNKNOWN	详细信息
methodTuning	4036	Manual Tuning	The user can set tuning PID coefficients.	msrc_UNKNOWN	详细信息
methodStrokeTime	4074	Stroke Time	set stroke time. Stroke time is used to limit rate of change of travel. Stroke time is expressed as sec/100% travel	msrc_UNKNOWN	详细信息
methodSetIPCount	4069	Set I/P Output	set I/P output.	msrc_UNKNOWN	详细信息
methodCalibSignal	403D	Input Current Sensor	To calibrate or to check the 4-20mA current sensor.	msrc_UNKNOWN	详细信息
methodCalibPressure	403E	Pressure Sensor	This operation will change zero calibration of all available pressure sensors .	msrc_UNKNOWN	详细信息
methodReadPressures	4028	Read Pressures	To read pressures.	msrc_UNKNOWN	详细信息
methodResetCalibrationData	4027	Reset Cal Factory Defaults	Reset Calibration Data: This will restore all sensor calibration data to factory defaults. If calibrations have been performed they will be lost!	msrc_UNKNOWN	详细信息
methodPerformDiagnostics	402B	Run Diagnostics	Perform valve signature and valve functional analysis. Displays the diagnostic test results.	msrc_UNKNOWN	详细信息
methodResetContinuous	4051	Reset Historian	Reset valve historian data (stroke count, cycle count, time open, time closed and time near closed ) to 0. The previous data is lost and must be recorded to be used later.	msrc_UNKNOWN	详细信息
methodReset	401F	Reset SVI II AP	This function performs a master reset to the device, causing it to go through its startup routine and re-initializing all of its operating parameters from non volatile memory.	msrc_UNKNOWN	详细信息
methodInterruptProcessNoModeChange	40BD	Stop Procedure		msrc_UNKNOWN	详细信息
methodDisableSwitchPositionLimits	4158	disble the fswitch1value, and fswitch2value		msrc_UNKNOWN	详细信息
TS_limit_check_method	415B	Tight Shutoff Limit Check		msrc_UNKNOWN	详细信息
pos_limit_check_method	40EA	Position Limit Check		msrc_UNKNOWN	详细信息
Transfer_Time_check_method	415C	Transfer Time Check		msrc_UNKNOWN	详细信息
Near_Pos__check_method	415D	Near Closed Value Check		msrc_UNKNOWN	详细信息
signal_range_check_method	40F7	Signal Range Check		msrc_UNKNOWN	详细信息
mthdReadCustomCharacterizationData	4192	Read Custom Characterization Data	Select characterization. If Custom is selected then continue to set custom points.	msrc_UNKNOWN	详细信息
mthdCheckCharacterizationData	4193	Edit Characterization	Control valves are often characterized to give a specific relationship between flow capacity (Cv) and percent opening of the valve. The valve can be characterized with special purpose trim or with the SVI2AP positioner. Selecting Custom Configuration displays an additional screen where the user can enter a custom characterization curve to fit his/her needs. The curve can have up to 9 points and points in between are linearly interpolated.	msrc_UNKNOWN	详细信息
methodDoSaveSignature	4194	Save	Save the signature data.	msrc_UNKNOWN	详细信息
methodSaveSignature	4195	Save	save the current signature data	msrc_UNKNOWN	详细信息
methodBaselineSignature	4196	Baseline	Baselined the saved signature data.	msrc_UNKNOWN	详细信息
methodReadCurrentSignature	4197	Current	Load the current signature curve.	msrc_UNKNOWN	详细信息
methodReadSavedSignature	4199	Saved	Load the saved signature curve.	msrc_UNKNOWN	详细信息
methodReadBaselinedSignature	419A	Baseline	Load the baselined signature curve.	msrc_UNKNOWN	详细信息
methodTransSignatureData	4198	Translate Signature Data	Load the signature data from device	msrc_UNKNOWN	详细信息
methodCurrentMode	4142	What is Current Mode?	What is Current Mode? - To get the current mode of this device	msrc_UNKNOWN	详细信息
methodDiagnosDisplay	412A	Read Diagnostic Data	Displays CONTINUOUS DIAGNOSTIC DATA including number of full strokes the valve has made,the number of cycles (direction changes),the time the valve has spent open, the time the valve has been closed and the time the valve has spent throttling near the seat.	msrc_UNKNOWN	详细信息
methodReadRawData	4146	Read Raw Data	Returns information from the SVI2AP that is useful to Masoneilan technicians for diagnostic purposes. The information includes the input current on the auxiliary input channel, the A/D values from the pressure, signal, and position measurements, the D/A value of the signal to the I/P, and the internal SVI2AP temperature.	msrc_UNKNOWN	详细信息
名称	ID	标签	描述	类型	源代码