Loading…
Loading…
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |
|---|---|---|---|---|---|
| show_calibration_points_method | 4081 | Show Cal.Curve | Shows Calibration Curve | msrc_UNKNOWN | 详细信息 |
| do_calibration_method | 4082 | Sort&Check Curve | Sort&Check Calibration Curve | msrc_UNKNOWN | 详细信息 |
| enter_cal_point_method | 4083 | Enter Cal.Pt. | Enter Calibration Point | msrc_UNKNOWN | 详细信息 |
| enter_background_method | 4084 | Set Background | It is important to measure the background when the probe is a rod detector. The background is the natural radiation only. The background must be measured, when the source is not yet installed on the vessel. | msrc_UNKNOWN | 详细信息 |
| enter_adjust_lower_cal_point_method | 4085 | Adjust Lo.Cal.Pt. | Adjusts Lower Calibration Point | msrc_UNKNOWN | 详细信息 |
| enter_adjust_upper_cal_point_method | 4086 | Adjust Up.Cal.Pt. | Adjusts Upper Calibration Point | msrc_UNKNOWN | 详细信息 |
| error_log_method | 4087 | Show Error Log | Shows the last occured errors. | msrc_UNKNOWN | 详细信息 |
| change_password_method | 4088 | Change Password | This is a availability to set up max. 3 password levels. The password for the full access level includes the access to configuration and calibration too. Each password can be different or equal to another password. Password for access Read Only can't be changed. | msrc_UNKNOWN | 详细信息 |
| enter_password_method | 4089 | Enter Access Password | In order to get access to other level, the right password must be entered. | msrc_UNKNOWN | 详细信息 |
| abort_restore_factory_setting_method | 40EC | msrc_UNKNOWN | 详细信息 | ||
| restore_factory_settings_method | 408A | Factory Settings | Factory Reset will delete all settings and restore the factory default values. | msrc_UNKNOWN | 详细信息 |
| save_cal_curve_as_basic_curve_method | 408B | Save | Save the current calibration curve in a separate register. E.g. a Basic Calibration Curve. | msrc_UNKNOWN | 详细信息 |
| load_basic_curve_method | 408C | Load | Load a previous stored calibration curve, and overwrite the current one. | msrc_UNKNOWN | 详细信息 |
| sensor_reset_method | 40CF | Hardware Reset | Hardware Reset will restart the CPU without loosing data. | msrc_UNKNOWN | 详细信息 |
| pre_edit_digital_output_method | 40D0 | msrc_UNKNOWN | 详细信息 | ||
| post_edit_digital_output_method | 40D1 | msrc_UNKNOWN | 详细信息 | ||
| digital_output_test_method | 40ED | Dig.Output Test | Runs Digital Output Test | msrc_UNKNOWN | 详细信息 |
| plateau_measurement_method | 40D2 | Measure Plateau | Runs Plateau measurement | msrc_UNKNOWN | 详细信息 |
| show_plateau_points_method | 40D3 | Show Plateau | Shows Plateau Points | msrc_UNKNOWN | 详细信息 |
| show_operating_mode_method | 40EE | Show Op.Mode | Shows Operation Mode | msrc_UNKNOWN | 详细信息 |
| refresh_dig_out_parameter_method | 40DA | Updating......... | msrc_UNKNOWN | 详细信息 | |
| write_and_refresh_dig_out_parameter_method | 40DB | Updating......... | msrc_UNKNOWN | 详细信息 | |
| refresh_dig_in_parameter_method | 40DD | Updating......... | msrc_UNKNOWN | 详细信息 | |
| write_and_refresh_dig_in_parameter_method | 40EF | Updating......... | msrc_UNKNOWN | 详细信息 | |
| refresh_var_loop_current_error_method | 40D7 | Updating......... | msrc_UNKNOWN | 详细信息 | |
| refresh_var_damping_mode_method | 40D9 | Updating......... | msrc_UNKNOWN | 详细信息 | |
| refresh_var_interference_detect_ctrl_method | 40DF | Updating......... | msrc_UNKNOWN | 详细信息 | |
| refresh_var_level_units_method | 40D6 | Updating......... | msrc_UNKNOWN | 详细信息 | |
| write_and_refresh_var_detector_hv_ctrl_method | 40D8 | Updating......... | msrc_UNKNOWN | 详细信息 | |
| loop_test | 1002 | 回路测试 | 回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。 | msrc_UNKNOWN | 详细信息 |
| dac_trim | 1004 | D/A修正 | 数字到模拟修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。 | msrc_UNKNOWN | 详细信息 |
| return_to_normal | 1016 | 中止返回正常 | msrc_UNKNOWN | 详细信息 | |
| leave_fixed_current_mode | 1003 | 退出固定电流模式 | 退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。 | msrc_UNKNOWN | 详细信息 |
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |