Loading…
Loading…
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |
|---|---|---|---|---|---|
| method_ds_loop_test | 410F | Loop test | 回路测试——允许用户将选择的模拟量输出手动调节至选择的常数输出值。 | msrc_UNKNOWN | 详细信息 |
| method_ds_da_trim | 4113 | D/A trim | 数字到模拟修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。 | msrc_UNKNOWN | 详细信息 |
| method_ds_scaled_da_trim | 4114 | Scaled D/A trim | 数字到模拟缩放修正——允许对选择的模拟量输出进行标定，在模拟量输出的操作端点有外部参考。 | msrc_UNKNOWN | 详细信息 |
| ds_leave_fixed_current_mode | 411B | 退出固定电流模式 | 退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。 | msrc_UNKNOWN | 详细信息 |
| method_ds_scv_trim_reset | 4116 | PV trim value reset | PV trim value reset- Reset PV trim value to 0.000. | msrc_UNKNOWN | 详细信息 |
| method_ds_cf_reset | 4119 | CF reset | CF reset- Reset the latest Calibration Factor value to 1.00000. It reset Calibration failure of Diag status. And it set the latest calibration status Calib status to Success | msrc_UNKNOWN | 详细信息 |
| method_ds_manual_calib_start | 4117 | Manual calib Start | Manual calib Start- Start the manual calibration process. Once manual calibration start, it can not stop till end. | msrc_UNKNOWN | 详细信息 |
| method_ds_auto_calib_start_stop | 411A | Auto calib Start/Stop operation | Auto calibration Start/Stop operation. | msrc_UNKNOWN | 详细信息 |
| method_ds_ao_failsafe_sim | 4110 | Fail safe simulation | Fail safe simulation- Simurates the analog output at the fail safe condition. After the fail safe simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. | msrc_UNKNOWN | 详细信息 |
| method_ds_failsafe_sim_clear | 411C | End Fail safe simulation. | End Fail safe simulation. | msrc_UNKNOWN | 详细信息 |
| method_ds_do_status_sim | 4111 | STATUS simulation | STATUS simulation- Simulates the STATUS output, Open or Close. After the STATUS output simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. If Continue is pressed, the simulation continues for 10 minutes or 2 hours more. | msrc_UNKNOWN | 详细信息 |
| method_ds_status_sim_clear | 411D | End- Simulates the STATUS output. | End- Simulates the STATUS output. | msrc_UNKNOWN | 详细信息 |
| method_ds_do_calib_sim | 4112 | CALIB simulation | CALIB simulation- Simulates the CALIB output, Open or Close. After the CALIB output simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. If Continue is pressed, the simulation continues for 10 minutes or 2 hours more. | msrc_UNKNOWN | 详细信息 |
| method_ds_calib_sim_clear | 411E | End- Simulates the CALIB output. | End- Simulates the CALIB output. | msrc_UNKNOWN | 详细信息 |
| method_ds_calib_log_clear | 4109 | Calib log clear | Calib log clear- Clears the Calib log in device. | msrc_UNKNOWN | 详细信息 |
| method_ds_error_log_clear | 410B | Error log clear | Error log clear- Clears the Error log in device. | msrc_UNKNOWN | 详细信息 |
| method_ds_conf_log_clear | 410D | Config log clear | Config log clear- Clears the Config log in device. | msrc_UNKNOWN | 详细信息 |
| method_ds_upload_gascvd_data | 4129 | Upload GasCVD data | Upload GasCVD data- Upload GasCVD dynamic data in device. | msrc_UNKNOWN | 详细信息 |
| method_ds_ad_refresh | 412B | Refresh AD count | Refresh AD count- Read latest AD count from GasCVD. | msrc_UNKNOWN | 详细信息 |
| leave_fixed_current_mode | 1003 | 退出固定电流模式 | 退出固定电流模式——使选择的模拟量输出退出输出为常数值的模式，使输出返回输出跟踪输入的模式。 | msrc_UNKNOWN | 详细信息 |
| return_to_normal | 1016 | 中止返回正常 | msrc_UNKNOWN | 详细信息 | |
| warning_message | 1017 | 设置回路为手动 | msrc_UNKNOWN | 详细信息 | |
| 名称 | ID | 标签 | 描述 | 类型 | 源代码 |