Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| method_ds_loop_test | 410F | Loop test | ﾙｰﾌﾟ ﾃｽﾄ - ｱﾅﾛｸﾞ出力をﾕｰｻﾞｰが選択した値で固定出力します | msrc_UNKNOWN | Details |
| method_ds_da_trim | 4113 | D/A trim | D/A ﾄﾘﾑ (ﾃﾞｼﾞﾀﾙ/ｱﾅﾛｸﾞ ﾄﾘﾑ) - ｵﾍﾟﾚｰﾃｨﾝｸﾞ ｴﾝﾄﾞ ﾎﾟｲﾝﾄに対するｱﾅﾛｸﾞ出力と外部指示計とのｷｬﾘﾌﾞﾚｰｼｮﾝを行います。 | msrc_UNKNOWN | Details |
| method_ds_scaled_da_trim | 4114 | Scaled D/A trim | ｽｹｰﾘﾝｸﾞ D/A ﾄﾘﾑ - ｵﾍﾟﾚｰﾃｨﾝｸﾞ ｴﾝﾄﾞ ﾎﾟｲﾝﾄに対する選択したｱﾅﾛｸﾞ出力と外部指示系とのｷｬﾘﾌﾞﾚｰｼｮﾝを行います。 | msrc_UNKNOWN | Details |
| ds_leave_fixed_current_mode | 411B | 固定電流ﾓｰﾄﾞを終ります | 現在の固定ﾓｰﾄﾞを終了 - ｱﾅﾛｸﾞ出力を定数値のﾓｰﾄﾞから移行させ, 出力が入力に応じて変わるﾓｰﾄﾞに戻します。 | msrc_UNKNOWN | Details |
| method_ds_scv_trim_reset | 4116 | PV trim value reset | PV trim value reset- Reset PV trim value to 0.000. | msrc_UNKNOWN | Details |
| method_ds_cf_reset | 4119 | CF reset | CF reset- Reset the latest Calibration Factor value to 1.00000. It reset Calibration failure of Diag status. And it set the latest calibration status Calib status to Success | msrc_UNKNOWN | Details |
| method_ds_manual_calib_start | 4117 | Manual calib Start | Manual calib Start- Start the manual calibration process. Once manual calibration start, it can not stop till end. | msrc_UNKNOWN | Details |
| method_ds_auto_calib_start_stop | 411A | Auto calib Start/Stop operation | Auto calibration Start/Stop operation. | msrc_UNKNOWN | Details |
| method_ds_ao_failsafe_sim | 4110 | Fail safe simulation | Fail safe simulation- Simurates the analog output at the fail safe condition. After the fail safe simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. | msrc_UNKNOWN | Details |
| method_ds_failsafe_sim_clear | 411C | End Fail safe simulation. | End Fail safe simulation. | msrc_UNKNOWN | Details |
| method_ds_do_status_sim | 4111 | STATUS simulation | STATUS simulation- Simulates the STATUS output, Open or Close. After the STATUS output simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. If Continue is pressed, the simulation continues for 10 minutes or 2 hours more. | msrc_UNKNOWN | Details |
| method_ds_status_sim_clear | 411D | End- Simulates the STATUS output. | End- Simulates the STATUS output. | msrc_UNKNOWN | Details |
| method_ds_do_calib_sim | 4112 | CALIB simulation | CALIB simulation- Simulates the CALIB output, Open or Close. After the CALIB output simulation starts, it will continue for 10 minutes and then it will automatically return to normal states. If Continue is pressed, the simulation continues for 10 minutes or 2 hours more. | msrc_UNKNOWN | Details |
| method_ds_calib_sim_clear | 411E | End- Simulates the CALIB output. | End- Simulates the CALIB output. | msrc_UNKNOWN | Details |
| method_ds_calib_log_clear | 4109 | Calib log clear | Calib log clear- Clears the Calib log in device. | msrc_UNKNOWN | Details |
| method_ds_error_log_clear | 410B | Error log clear | Error log clear- Clears the Error log in device. | msrc_UNKNOWN | Details |
| method_ds_conf_log_clear | 410D | Config log clear | Config log clear- Clears the Config log in device. | msrc_UNKNOWN | Details |
| method_ds_upload_gascvd_data | 4129 | Upload GasCVD data | Upload GasCVD data- Upload GasCVD dynamic data in device. | msrc_UNKNOWN | Details |
| method_ds_ad_refresh | 412B | Refresh AD count | Refresh AD count- Read latest AD count from GasCVD. | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | 固定電流ﾓｰﾄﾞを終ります | 現在の固定ﾓｰﾄﾞを終了 - ｱﾅﾛｸﾞ出力を定数値のﾓｰﾄﾞから移行させ, 出力が入力に応じて変わるﾓｰﾄﾞに戻します。 | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| warning_message | 1017 | ﾙｰﾌﾟをﾏﾆｭｱﾙにします | msrc_UNKNOWN | Details | |
| Name | ID | Label | Description | Type | Source |