Device dictionary

Loading…

Reference ID	String
0	9739MVD
1	Model
2	Transmitter Software
3	.1f
4	Universal
5	Field Device
6	DescriÃ§Ã£o
7	Hardware
8	A000: Undefined
9	A001: EEPROM Error (CP)
10	A002: RAM Error (CP)
11	A003: No Sensor Response
12	A004: Temperature Overrange
13	A005: Mass Flow Overrange
14	A006: Characterization Required
15	A007: Real-Time Interrupt Failure
16	A008: Density Overrange
17	A009: Transmitter Initializing/Warming Up
18	A010: Calibration Failure
19	A011: Zero Calibration Failed: Low
20	A012: Zero Calibration Failed: High
21	A013: Zero Calibration Failed: Unstable
22	A014: Transmitter Failure
23	A015: MA Readback Error
24	A016: Sensor RTD Failure
25	A017: T-Series RTD Failure
26	A018: EEPROM Error (Xmtr)
27	A019: RAM Error (Xmtr)
28	A020: No Flow Cal Value
29	A021: No K1 Value
30	A022: Config DB Corrupt (CP)
31	A023: Internal Totals Corrupt (CP)
32	A024: Program Corrupt (CP)
33	A025: Boot Sector Fault (CP)
34	A027: Security Breach
35	A028: CP Write Failure
36	A029: PIC/Daughterboard Comm Failure
37	A030: Incorrect Board Type
38	A031: Low Power
39	A032: MV: Outputs to Fault
40	A033: No LPO/RPO Signal
41	A034: Meter Verification Failed
42	A035: Meter Verification Aborted
43	A036: Undefined
44	A037: Undefined
45	A038: Undefined
46	A039: Undefined
47	A100: MAO1 Saturated
48	A101: MAO1 Fixed
49	A102: Drive Overrange
50	A103: Data Loss Possible
51	A104: Calibration-In-Progress
52	A105: Slug Flow
53	A106: Burst Mode Enabled
54	A107: Power Reset Occurred
55	A108: Single-SP Event 1 ON
56	A109: Single-SP Event 2 ON
57	A110: FO Saturated
58	A111: FO Fixed
59	A112: Upgrade Transmitter Software
60	A113: MAO2 Saturated
61	A114: MAO2 Fixed
62	A115: No External Data
63	A116: API: Temperature Overrange
64	A117: API: Density Overrange
65	A118: DO1 Fixed
66	A120: ED: Curve Fit Failure
67	A121: ED: Extrapolation alarm
68	A124: FI Saturated
69	A129: PPI Display Error
70	A130: Undefined
71	A131: Reserved
72	A132: Sensor Simulation Active
73	A133: PIC UI EEPROM Error
74	A134: PPI Memory Error
75	A135: PPI Communication Error
76	A136: Undefined
77	A137: Undefined
78	A138: TBR Active
79	A139: Undefined
80	D1 Calibration In Progress
81	D2 Calibration In Progress
82	D3 Calibration In Progress
83	D4 Calibration In Progress
84	FD Calibration In Progress
85	Zero Calibration In Progress
86	Temperature Slope Calibration In Progress
87	Temperature Offset Calibration In Progress
88	Discrete Event 1 Active
89	Discrete Event 2 Active
90	Discrete Event 3 Active
91	Discrete Event 4 Active
92	Discrete Event 5 Active
93	Discrete Output 1 Active
94	Discrete Input 1 Active
95	Reserved
96	Undefined
97	Undefined
98	Flow Switch Hysteresis Out of Range
99	Invalid Channel A Assignment Code
100	Invalid Channel B Assignment Code
101	Invalid Channel C Assignment Code
102	Invalid Channel D Assignment Code
103	Invalid Channel E Assignment Code
104	Invalid Channel F Assignment Code
105	Invalid Channel A Power Source Code
106	Invalid Channel B Power Source Code
107	Invalid Channel C Power Source Code
108	Invalid Channel D Power Source Code
109	Invalid Channel E Power Source Code
110	Invalid Channel F Power Source Code
111	Invalid Units Code
112	Invalid Milliamp Input Variable Code
113	Enable Concentration Measurement Code Out of Range
114	Enable Curve Lock Code Out of Range
115	Invalid Concentration Units Code
116	Invalid Temperature Units Code
117	Invalid Density Units Code
118	Transmitter-Specific Command Error (Invalid CM curve)
119	Reference Temperature Out of Range
120	Water Reference Temperature Out of Range
121	Water Reference Density Out of Range
122	Slope Trim Out of Range
123	Slope Offset Out of Range
124	Extrapolation Alarm Limit Out of Range
125	Max Fit Order Out of Range
126	Invalid Curve Index
127	Invalid Data Index
128	Current (mA Output 1)
129	Current (mA Output 2)
130	Current (mA Input)
131	Offset Calibration
132	Slope Calibration
133	mA Output 2 Loop Test
134	Trim mA Output 1
135	Trim mA Output 2
136	Resets internal totalizers.
137	Display K Factor
138	The number of pulses per unit of measure output via the frequency output
139
140	Inputs/Outputs
141	Frequency Output
142	Alterar gravidade do alerta
143	AtribuiÃ§Ã£o de aÃ§Ã£o de leitura discreta
144	Rever todas as aÃ§Ãµes discretas
145	Discrete Output Test
146	mA Outputs
147	Additional Information for Above
148	No Additional Information for Above
149	Reset Matrix Data
150	Load Matrix Data From Device
151	Enter Matrix
152	Refresh Hours Since Last Run
153	Ler dados modbus
154	Escrever dados modbus
155	mA Input
156	Configure Matrix
157	Trim Concentration Measurement Process Variables
158	Reiniciar dispositivo
159	Restaure a config de fÃ¡brica
160	IdentificaÃ§Ã£o
161	Revisions
162	HART Burst Mode
163	Set Up mA Input
164	Discrete Input
165	ParÃ¢metros informativos
166	InformaÃ§Ã£o do transmissor
167	Inputs/Outputs Fault Actions
168	Discrete Output
169	Digital Communications
170	Modbus Data
171	Concentration Measurement
172	Concentration Measurement Configuration
173	Matrix Configuration
174	Isotherm 1
175	Isotherm 2
176	Isotherm 3
177	Isotherm 4
178	Isotherm 5
179	Isotherm 6
180	Entrada em mA
181	Redefinir/Restaurar
182	.2f
183	.3f
184	.4f
185	.5f
186	4.2f
187	Transmitter Serial Number
188	8d
189	8.2f
190	8.3f
191	8.6f
192	.6f
193	10.4f
194	6.2f
195	Sensor Flange
196	Tube Lining
197	Tube Wetted Material
198	5.4f
199	5.2f
200	5d
201	5.3f
202	5.5f
203	uSec
204	6.5f
205	2d
206	Fault Action
207	Escala superior (21,0-24,0 mA)
208	Escala inferior (1,0-3,6 mA)
209	Fault Action
210	Digital Fault Actions
211	Fault Level
212	Fault Level
213	1d
214	7.2f
215	4d
216	Polled Variable 1
217	Polled Variable 2
218	9.8f
219	10.7f
220	Meter Verify Failed
221	RS485 Dual Function
222	Discrete Input State
223	Discrete Input State 2
224	3d
225	VariÃ¡vel
226	Tipo de evento
227	NLPD
228	NLPH
229	NLPM
230	NLPS
231	Nm3/day
232	Nm3/hr
233	Nm3/min
234	Nm3/sec
235	SCFD
236	SCFH
237	SCFM
238	SCFS
239	SLPD
240	SLPH
241	SLPM
242	SLPS
243	Sm3/day
244	Sm3/hr
245	Sm3/min
246	Sm3/sec
247	SL
248	Sm3
249	Special
250	Simulate Primary Purpose Variables
251	Simulation Control
252	Simulation Fixed Value
253	Simulation Ramp Low Point
254	Simulation Ramp High Point
255	Simulation Ramp Period
256	V
257	mmi_current algorithm state_label
258	Set Frequency Input Scaling
259	4.1f
260	Hours Since Last Run
261	Active Matrix
262	Curve 1
263	Curve 2
264	Curve 3
265	Curve 4
266	Curve 5
267	Curve 6
268	Reference Temperature
269	The reference temperature of the fluid
270	Water Reference Temperature
271	Trim Slope
272	Trim Offset
273	Extrapolation Alarm Limit
274	Matrix Name
275	Curve Name
276	Curve Fit Maximum Order
277	Curve Fit Max Order
278	Curve Fit Results
279	Good
280	Poor
281	Failed
282	Empty
283	Concentration Units
284	Accuracy
285	Enabled
286	Enable Concentration Measurement
287	Enable ED
288	Lock/Unlock Concentration Matrices
289	Indicates whether the curve is locked from writing
290	Not Locked
291	Locked
292	Derived Variable
293	Standard
294	Density at Ref.
295	S.G.
296	Mass Conc(Dens)
297	Mass Conc(SG)
298	Volume Conc(Dens)
299	Volume Conc(SG)
300	Conc(Dens)
301	Conc(SG)
302	Water Reference Density
303	Reason for Abort
304	Transmitter Running Seconds at Test
305	Enable Temperature High Extrapolation Limit
306	Disabled
307	Enable Density Low Extrapolation Limit
308	Enable Density High Extrapolation Limit
309	Enable Temperature Low Extrapolation Limit
310	Slope
311	Offset
312	2
313	3
314	4
315	5
316	Temperature Units
317	Density Units
318	Concentration Unit String
319	Matrix Being Configured
320	Channel D
321	Channel E
322	Channel F
323	Milliampere Input
324	Power Source
325	Channel D Power Source
326	DO Power Source
327	Concentration 1
328	Concentration 2
329	Concentration 3
330	Concentration 4
331	Concentration 5
332	SpecConc0
333	SpecConc1
334	SpecConc2
335	SpecConc3
336	SpecConc4
337	SpecConc5
338	DensAtConc0
339	DensAtConc1
340	DensAtConc2
341	DensAtConc3
342	DensAtConc4
343	DensAtConc5
344	Density
345	Density
346	Density
347	Density
348	Density
349	4.4f
350	mA Input Upper Range Value
351	mA Input Lower Range Value
352	mA Input Level
353	mA Input Variable Assignment
354	External Pressure
355	External Temperature
356	None
357	Milliamp Input Units
358	API Vol Flow Digital Units
359	API Dens Digital Units
360	ED Vol Flow Digital Units
361	ED Dens Digital Units
362	Manter atribuiÃ§Ã£o existente
363	Configure map variables, primary and secondary output, discrete outputs, pulse output, discrete inputs, pulse input settings and RS-485 port.
364	Unit Codes
365	Alert Severity
366	Enter an Alert number and change the Alert's severity to Fault, Information or Ignore.
367	Enter an Alert number and view the current severity of the alert.
368	Revision Numbers
369	State is On.
370	State is Off.
371	Esta tela nÃ£o atualizarÃ¡ automaticamente depois de se alterar o campo 'tipo'. Selecione 'guia de configuraÃ§Ã£o' e entÃ£o retorne a esta tela para ver a configuraÃ§Ã£o atual.
372	Optional Setup
373	Configure the Process Monitor Screens by selecting the desired process variables for each screen.
374	Configure the number of decimal places for each process variable.
375	Digital to analog trim of the mA output 1.
376	Digital to analog trim of the mA output 2.
377	Perform First Point (Air) Calibration.
378	Perform Second Point (Water) Calibration.
379	Perform Flowing Density Calibration.
380	Perform Fourth Point (user’s choice) Calibration.
381	Set a fixed output value for the discrete output.
382	Simulation Configuration
383	Mass Flow Rate Simulation Settings
384	Density Simulation Settings
385	Temperature Simulation Settings
386	Loop Tests
387	Assign variables to the first and second milliamp outputs, define upper and lower range values, cutoffs, and dampings.
388	Assign variables to the discrete output, set flow switch.
389	Assign variables to the discrete input.
390	Assign range values to the milliamp input.
391	Set up Bell-202 port (HART only) and RS-485 port.
392	Set Up Bell 202 Port
393	mA Output Trim
394	Note: To assign action to discrete inputs go to alert setup, discrete events, assign discrete actions
395	CM Configuration
396	Methods
397	Concentration
398	Extrapolation Alert
399	Reference Conditions
400	AÃ§Ãµes recomendadas: 1. Verifique se hÃ¡ golfada (slug flow). 2. Examine as variÃ¡veis de diagnÃ³stico para verificar se os tubos estÃ£o vibrando. Pickoffs de esquerda e de direita devem ficar acima de 10mV. 3. Verifique os circuitos do sensor. 4. Verifique se hÃ¡ entupimentos nos tubos do sensor. 5. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 6. Se o problema persistir, entre em contato com a Micro Motion.
401	AÃ§Ãµes recomendadas: 1. Verifique se o sensor estÃ¡ conectado ao transmissor. 2. Verifique os circuitos RTD do sensor. 3. Verifique se a temperatura do processo estÃ¡ dentro da faixa do sensor e do transmissor. 4. Se o problema persistir, entre em contato com a Micro Motion.
402	AÃ§Ãµes recomendadas: 1. Se outros alertas estiverem presentes (tipicamente, A003, A006, A008, A102 ou A105), resolva aqueles alertas primeiramente. Se o alerta A005 persistir, continue com as sugestÃµes abaixo. 2. Examine as variÃ¡veis de diagnÃ³stico para verificar se os tubos estÃ£o vibrando. Pickoffs de esquerda e de direita devem ficar acima de 10mV. 3. Verifique os circuitos do sensor. 4. Verifique se hÃ¡ erosÃ£o nos tubos do sensor atravÃ©s da verificaÃ§Ã£o de densidade. 5. Se o problema persistir, entre em contato com a Micro Motion.
403	AÃ§Ãµes recomendadas: 1. Verifique a caracterizaÃ§Ã£o. Verifique especificamente os valores de Fluxo FCF e K1 na placa de identificaÃ§Ã£o do sensor. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 3. Se o problema persistir, entre em contato com a Micro Motion.
404	AÃ§Ãµes recomendadas: 1. Verifique a caracterizaÃ§Ã£o. Verifique especificamente os valores de FlowCal e K1 na placa de identificaÃ§Ã£o do sensor. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 3. Se o problema persistir, entre em contato com a Micro Motion.
405	AÃ§Ãµes recomendadas: 1. Se outros alertas estiverem presentes (tipicamente, A003, A006, A008, A102 ou A105), resolva aqueles alertas primeiramente. Se o alerta A008 persistir, continue com as sugestÃµes abaixo. 2. Verifique o processo. Verifique se hÃ¡ ar nos tubos de fluxo, se os tubos nÃ£o estÃ£o cheios, se hÃ¡ material estranho ou algum revestimento nos tubos. 3. Verifique os circuitos do sensor. 4. Verifique a caracterizaÃ§Ã£o da densidade e se a configuraÃ§Ã£o estÃ¡ compatÃvel com a placa de identificaÃ§Ã£o do sensor. 5. Examine as variÃ¡veis de diagnÃ³stico para verificar se a frequÃªncia de tubo bruto estÃ¡ na faixa adequada para o tipo de sensor. 6. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 7. Se o problema persistir, entre em contato com a Micro Motion.
406	AÃ§Ãµes recomendadas: 1. Deixe o medidor de fluxo se aquecer (aproximadamente 30 segundos). O erro deve desaparecer quando o medidor de fluxo estiver pronto para a operaÃ§Ã£o normal. 2. Verifique a tensÃ£o de entrada para garantir que esteja entre 12 e 15 V. 3. Se o alerta nÃ£o desaparecer, certifique-se de que o sensor esteja completamente cheio ou completamente vazio. 4. Verifique os circuitos do sensor. 5. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
407	AÃ§Ãµes recomendadas: 1. Se o alerta aparecer quando o transmissor estiver no ponto zero, certifique-se de que nÃ£o hÃ¡ fluxo atravÃ©s do sensor e entÃ£o, tente novamente. 2. Desligue e ligue o medidor de fluxo para limpar o alerta. 3. Se for apropriado, restaure o zero de fÃ¡brica para voltar a operar o medidor de fluxo. 4. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 5. Se o alerta aparecer durante uma calibraÃ§Ã£o de densidade, entre em contato com a Micro Motion.
408	Ações recomendadas: 1. Se o alerta aparecer quando o transmissor estiver no ponto zero, certifique-se de que não há fluxo através do sensor e então, tente novamente. 2. Desligue e ligue o medidor de fluxo para limpar o alerta. 3. Se for apropriado, restaure o zero de fábrica para voltar a operar o medidor de fluxo. 4. Se quiser alterar a gravidade do alerta, vá em Configurar (Configure)-> Configuração de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 5. Se o alerta aparecer durante uma calibração de densidade, entre em contato com a Micro Motion.
409	AÃ§Ãµes recomendadas: 1. Resolva primeiramente outros alertas ativos. 2. Desligue e ligue o medidor de fluxo. 3. Se o alerta persistir, o transmissor pode precisar de manutenÃ§Ã£o. Entre em contato com a Micro Motion.
410	AÃ§Ãµes recomendadas: 1. Verifique os circuitos do detector de temperatura de resistÃªncia (RTD) do sensor. 2. Verifique se a temperatura do processo estÃ¡ dentro da faixa do sensor e do transmissor. 3. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 4. Se o problema persistir, entre em contato com a Micro Motion.
411	AÃ§Ãµes recomendadas: 1.Desligue e ligue o transmissor. 2.Se o problema persistir, entre em contato com a Micro Motion.
412	AÃ§Ãµes recomendadas: 1. Verifique a caracterizaÃ§Ã£o em relaÃ§Ã£o Ã placa de identificaÃ§Ã£o do sensor. Verifique especificamente os valores de FCF (fator de calibraÃ§Ã£o de fluxo), K1 e K2. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 3. Se o problema persistir, entre em contato com a Micro Motion.
413	AÃ§Ãµes recomendadas: 1. Verifique a caracterizaÃ§Ã£o em relaÃ§Ã£o Ã placa de identificaÃ§Ã£o do sensor. Verifique especificamente os valores de FlowCal (calibraÃ§Ã£o de fluxo), K1 e K2. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 3. Se o problema persistir, entre em contato com a Micro Motion.
414	AÃ§Ãµes recomendadas: 1. Se A017 estiver ativo, resolva-o primeiramente. 2. Verifique a caracterizaÃ§Ã£o em relaÃ§Ã£o Ã placa de identificaÃ§Ã£o do sensor. Verifique especificamente os valores de FCF (fator de calibraÃ§Ã£o de fluxo), K1 e K2. 3. Verifique os circuitos do RTD (detector de temperatura da resistÃªncia) do sensor. 4. Se o problema persistir, entre em contato com a Micro Motion.
415	AÃ§Ãµes recomendadas: 1. Verifique a fiaÃ§Ã£o entre o transmissor e o processador central. 2. Verifique a entrada de energia para o transmissor e para o processador central. 3. Desligue e ligue o transmissor. 4. Se o problema persistir, entre em contato com a Micro Motion.
416	AÃ§Ãµes recomendadas: 1. O alarme pode ser anulado pelo usuÃ¡rio colocando o transmissor de volta no modo de seguranÃ§a, mas um procedimento autorizado Ã© necessÃ¡rio para selar o transmissor.
417	AÃ§Ãµes recomendadas: 1. Verifique se a tensÃ£o de entrada do processador central Ã© no mÃnimo 12 V. 2. Verifique a alimentaÃ§Ã£o de energia e toda a fiaÃ§Ã£o.
418	AÃ§Ãµes recomendadas: 1. Verifique se hÃ¡ golfada (slug flow). 2. Examine as variÃ¡veis de diagnÃ³stico para verificar se os tubos estÃ£o vibrando. Pickoffs de esquerda e de direita devem ficar acima de 10mV. 3. Verifique os circuitos do sensor. 4. Verifique se hÃ¡ entupimentos dos tubos do sensor. 5. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 6. Se o problema persistir, entre em contato com a Micro Motion.
419	AÃ§Ãµes recomendadas: 1. Verifique se a faixa de saÃda mA estÃ¡ configurada com valores apropriados. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
420	AÃ§Ãµes recomendadas: 1. Verifique o endereÃ§o HART. Se este for diferente de zero, configure o parÃ¢metro de aÃ§Ã£o de saÃda mA para habilitar a saÃda mA viva ou se for desejado um modo multiponto, altere a gravidade do alerta para ignorar indo Ã tela Configurar (Configure) -> ConfiguraÃ§Ã£o do alerta (Alert Setup) -> Gravidade do alerta (Alert Severity). 2. Se estiver executando o ajuste de saÃda mA, saia do ajuste de saÃda mA. 3. Se estiver executando o teste em loop da saÃda mA, saia do teste em loop da saÃda mA. 4. Verifique se a saÃda foi fixada atravÃ©s de comunicaÃ§Ãµes digitais ou do display local.
421	AÃ§Ãµes recomendadas: 1. Deixe que o medidor de fluxo termine a calibraÃ§Ã£o. 2. Para procedimentos de calibraÃ§Ã£o de zero, vocÃª pode abortar a calibraÃ§Ã£o, configurar o parÃ¢metro de tempo zero para um valor mais baixo e reiniciar a calibraÃ§Ã£o. 3. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
422	AÃ§Ãµes recomendadas: 1. Nenhuma aÃ§Ã£o necessÃ¡ria. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
423	AÃ§Ãµes recomendadas: 1. Altere os fatores de escala de saÃda de frequÃªncia para configuraÃ§Ãµes mais apropriadas. 2. Se a terceira variÃ¡vel estiver configurada para fluxo de volume, a baixa densidade ou tubos vazios podem causar que a frequÃªncia de saÃda sature. 3. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
424	AÃ§Ãµes recomendadas: 1. Saia do teste em loop de frequÃªncia de saÃda. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
425	AÃ§Ãµes recomendadas: 1. Saia do teste de saÃda discreta. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
426	A119: Discrete Output 2 Fixed
427	AÃ§Ãµes recomendadas: 1. Verifique a configuraÃ§Ã£o da matriz de mediÃ§Ã£o de concentraÃ§Ã£o (CM) utilizando Configurar (Configure) -> ConfiguraÃ§Ã£o manual (Manual Setup) -> MediÃ§Ãµes (Measurements) -> MediÃ§Ã£o de concentraÃ§Ã£o (Concentration Measurement) -> Acessar matriz (Enter Matrix).
428	AÃ§Ãµes recomendadas: 1. Desabilite a simulaÃ§Ã£o de saÃda. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
429	AÃ§Ãµes recomendadas: 1. Verifique os circuitos do sensor. 2. Se este for o Ãºnico alarme ativo, ignore-o. Se desejado, reconfigure a gravidade do alarme para ignorar. 3. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
430	AÃ§Ãµes recomendadas: 1. Verificar se o transmissor e o processador central tÃªm a tensÃ£o de entrada apropriadas. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen). 3. Se o problema persistir, entre em contato com a Micro Motion.
431	AÃ§Ãµes recomendadas: 1. Verifique se o sensor estÃ¡ completamente cheio. 2. Verifique se os limites de slug estÃ£o configurados para valores apropriados. 3. Verifique se o limite de densidade estÃ¡ Ã no mÃnimo 0,2 g/cc. 4. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
432	AÃ§Ãµes recomendadas: 1. Nenhuma aÃ§Ã£o necessÃ¡ria. 2. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
433	AÃ§Ãµes recomendadas: 1. Verifique o processo. 2. Verifique a configuraÃ§Ã£o para a tabela de referÃªncia de mediÃ§Ãµes de petrÃ³leo e temperatura. 3. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
434	AÃ§Ãµes recomendadas: 1. Se outros alertas estiverem presentes, resolva-os primeiro. 2. Verifique o processo. 3. Verifique a configuraÃ§Ã£o para a tabela de referÃªncia de mediÃ§Ãµes de petrÃ³leo e densidade. 4. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
435	AÃ§Ãµes recomendadas: 1. Verifique a temperatura e a densidade do processo. 2. Verifique o limite de alerta para mediÃ§Ãµes de concentraÃ§Ã£o (CM). 3. Verifique o processo. Se os tubos estiverem vazios ou se houver gÃ¡s no processo, espere que as condiÃ§Ãµes sejam eliminadas. 4. Se quiser alterar a gravidade do alerta, vÃ¡ em Configurar (Configure)-> ConfiguraÃ§Ã£o de alerta (Alert setup) -> Tela de gravidade do alerta (Alert severity screen).
436	Frequency input from external device is too high.
437	Recommended Actions: 1. Verify that frequency input parameters are set to appropriate values.
438	Batch total has exceeded target: • Batch has not ended. • Flow is still being measured.
439	Recommended Actions: 1. Check wiring for discrete output indicating overrun. 2. Check device connected to discrete output indicating overrun. 3. Enable batch Automatic Overshoot Compensation (AOC). 4. After cause has been diagnosed, press RESET or START to start new batch.
440	A129: Internal Error (Display)
441	(Custody transfer only) Readback function from transmitter display indicates error or failure.
442	Recommended Actions: 1. Cycle power to the flow meter. 2. If problem persists, call Micro Motion.
443	(Custody transfer only) The ticket printer is out of paper.
444	Recommended Actions: 1. Add paper to the printer.
445	A134: Memory Error (Display)
446	Memory or checksum error in transmitter display.
447	Recommended Actions: 1. Cycle power to the flow meter. 2. The flow meter might need service. Contact Micro Motion.
448	A135: Transmitter/Display Communications Error
449	Internal communication error with transmitter display.
450	A136: Power Outage
451	The power was off for at least 30 seconds.
452	Recommended Actions: 1. No action required.
453	A137: Measurement Paused
454	Continuous mode measurements are paused.
455	Recommended Actions: 1. No action required. If desired, resume measurement.
456	A138: Transient Bubble Remediation (TBR) Active
457	The drive gain has exceeded the configured TBR threshold and the configured TBR action has been implemented.
458	A139: External Water Cut Out-of-Range
459	The water cut measured by the water cut monitor is above the configured External Water Cut Limit.
460	AÃ§Ãµes recomendadas: 1. Verifique o processo e a presenÃ§a de golfada (slug flow). 2. Verifique as variÃ¡veis de diagnÃ³stico. 3. Verifique os circuitos do sensor. 4. Verifique se hÃ¡ erosÃ£o nos tubos do sensor. 5. Se o problema persistir, entre em contato com a Micro Motion.
461	Reference Condition
462	Read modbus register values.
463	Electronic Conditions
464	Sensor Conditions
465	Recommended Actions: 1. Check for slug flow. 2. Check the test points. 3. Check the sensor circuitry. 4. Check sensor tubes for plugging. 5. If the problem persists, contact Micro Motion.
466	Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. If the problem persists, contact Micro Motion.
467	Process Conditions
468	Recommended Actions: 1. If other alerts are present (typically, A003, A006, A008, A102, or A105), resolve those alerts first. If the A005 alert persists, continue with the suggestions below. 2. Verify process and check for slug flow. 3. Check the test points. 4. Check the sensor circuitry. 5. Check the sensor tubes for erosion. 6. If the problem persists, contact Micro Motion.
469	Configuration Conditions
470	Recommended Actions: 1. Check the characterization. Specifically, verify the FCF and K1 values. 2. If the problem persists, contact Micro Motion.
471	Recommended Actions: 1. If other alerts are present (typically, A003, A006, A102, or A105), resolve those alerts first. If the A008 alert persists, continue with the suggestions below. 2. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes. 3. Check for slug flow. 4. Check the sensor circuitry. 5. Verify calibration factors in transmitter configuration. 6. Check the test points. 7. If the problem persists, contact Micro Motion.
472	Recommended Actions: 1. Allow the flowmeter to warm up (approximately 30 seconds). The error should disappear once the flowmeter is ready for normal operation. 2. If alert does not clear, make sure that the sensor is completely full or completely empty. 3. Check the sensor circuitry.
473	Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
474	Recommended Actions: 1. Ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
475	Recommended Actions: 1. Remove or reduce sources of electromechanical noise, then retry. Sources of noise include mechanical pumps, pipe stress at sensor, electrical interference, or vibration effects from nearby machinery. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
476	Recommended Actions: 1. Cycle power to the flowmeter. 2. The transmitter might need service. Contact Micro Motion.
477	Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. Check the characterization. Specifically, verify the FCF and K1 values. 4. If the problem persists, contact Micro Motion.
478	Recommended Actions: 1.Cycle power to the transmitter. 2.If problem persists, call Micro Motion.
479	Recommended Actions: 1. Check the characterization. Specifically, verify the FCF and K1 values. 2. Check the sensor RTD circuitry. 3. If the problem persists, contact Micro Motion.
480	Recommended Actions: 1.Cycle power to the flowmeter. 2.The transmitter might need service. Contact Micro Motion.
481	Recommended Actions: 1. Verify the wiring between the Transmitter and Core Processor. 2. Cycle power to the transmitter. 3. If problem persists, call Micro Motion.
482	Recommended Actions: 1. Alarm can be cleared by user, but authorized procedure is required to reestablish security.
483	Recommended Actions: 1. Cycle power to the flowmeter. 2. The transmitter might need service or upgrading. Contact Micro Motion.
484	Recommended Actions: 1. Cycle power to the flowmeter. 2. Contact Micro Motion.
485	Recommended Actions: 1. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes.
486	Recommended Actions: 1. Check the sensor circuitry. 2. If this is the only active alarm, it can be ignored. If desired, reconfigure the alarm severity to Ignore.
487	Recommended Actions: 1. Contact Micro Motion to upgrade the transmitter software. Note: The transmitter is still functional.
488	Recommended Actions: 1. No action required. 2. If desired, reconfigure the alarm severity to Ignore.
489	Recommended Actions: 1. HART polling connection to external device has failed. Ensure that external device is available: 2. Verify device operation. 3. Verify wiring. 4. Verify polling configuration.
490	Recommended Actions: 1. Verify process. 2. Verify configuration for Petroleum Measurement reference table and temperature.
491	Recommended Actions: 1. Verify process. 2. Verify configuration for Petroleum Measurement reference table and density.
492	Recommended Actions: 1. Verify the process temperature and density. 2. Verify Concentration Measurement (CM) configuration.
493	Recommended Actions: 1. Verify process and check for slug flow. 2. Check the test points. 3. Check the sensor circuitry. 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
494	Recommended Actions: 1. Verify that mA output range values are set to appropriate values.
495	Recommended Actions: 1. The first command to recognize this condition will automatically reset this flag. 2. This flag may also be set following a Master Reset or a Self Test.
496	Recommended Actions: 1. Check the test points. 2. Check the sensor circuitry. 3. If the problem persists, contact Micro Motion.
497	Recommended Actions: 1. Allow the flowmeter to complete calibration. 2. For zero calibration procedures, you may abort the calibration, set the zero time parameter to a lower value, and restart the calibration.
498	Recommended Actions: 1. Disable output simulation.
499	Recommended Actions: 1. Check the HART address. If non-zero, enable Loop Current Mode parameter. 2. Exit mA output trim. 3. Exit mA output loop test. 4. Check to see if the output has been fixed via digital communication.
500	Recommended Actions: 1. Change frequency output scaling factors to more appropriate settings.
501	Recommended Actions: 1. Exit frequency output loop test.
502	Recommended Actions: 1. Exit mA output trim. 2. Exit mA output loop test. 3. Check to see if the output has been fixed via digital communications.
503	Recommended Actions: 1. Verify Concentration Measurement (CM) configuration.
504	Classic View
505	mA Output 1
506	mA Output 2
507	Ver variáveis de diagnóstico
508	Ver caracterização de densidade
509	Ver condições de golfada (slug flow)
510	Ver as variáveis de medições de concentração
511	Caracterização de densidade
512	Condição de golfada (slug flow)
513	CalibraÃ§Ã£o
514	Realize uma calibraÃ§Ã£o zero.
515	Realize uma calibraÃ§Ã£o da densidade.
516	Performs a temperature calibration.
517	Ligar e desligar o dispositivo sem afetar sua configuraÃ§Ã£o.
518	Sobregravar a configuraÃ§Ã£o existente do dispositivo com a configuraÃ§Ã£o definida na fÃ¡brica.
519	Redefina manualmente a sinalizaÃ§Ã£o de configuraÃ§Ã£o alterada se o host nÃ£o puder redefinir a sinalizaÃ§Ã£o automaticamente.
520	FMU860
521	DT
522	DVC
523	FCX
524	AS800
525	340T
526	340C
527	344
528	Siemens Micro K
529	SITRANS L
530	SIPAN PH
531	SITRANS P
532	75SMT
533	UNIDELTA
534	8320
535	SX5100
536	TSV175
537	DMU
538	3780
539	BM70
540	8u
541	low
542	high
543	tmp_av
544	A alteraÃ§Ã£o da configuraÃ§Ã£o pode afetar a operaÃ§Ã£o o transmissor. Certifique-se de que o circuito de controle esteja definido para operaÃ§Ã£o manual antes de continuar.
545	Calibration is in progress...
546	Density calibration is completed.
547	Frequency Output:
548	Enter Meter Value:
549	Selftest complete
550	No Device Problems seen during Selftest
551	WARN-Stopping totalizer disables frequency output
552	ERROR: Totalizer reset not allowed when flow is not zero.
553	Ev1 Triggered: Yes
554	Ev1 Triggered: No
555	Ev2 Triggered: Yes
556	Ev2 Triggered: No
557	Transmitter status complete
558	Transmitter status OK
559	NOTE-Loop may be returned to automatic control
560	NOTE-Send PV assignment before modifying range values.
561	NOTE-Send SV assignment before modifying range values.
562	NOTE-Send TV assignment before modifying frequency scaling.
563	K-Factor: %{yatemp} pulses/unit.
564	floatFreqVal
565	floatRateVal
566	Please select Burst Mode:
567	A problem was detected
568	Abort;Fix and Retry
569	Choose Burst Variable:
570	Burst mode configuration is completed. Note-Please return loop to automatic control.
571	select
572	floatPulsesPerUnit
573	floatUnitsPerPulse
574	Current primary variable selection is mass flow rate. Select Primary Variable:
575	Current Selection;Mass Flow Rate;Temperature;Density;Volume Flow Rate;Viscosity;Differential Pressure;Event1;Event2
576	Current primary variable selection is temperature. Select Primary Variable:
577	Current primary variable selection is density. Select Primary Variable:
578	Current primary variable selection is volume flow rate. Select Primary Variable:
579	Current primary variable selection is viscosity. Select Primary Variable:
580	Current primary variable selection is differential pressure. Select Primary Variable:
581	Current primary variable selection is event1. Select Primary Variable:
582	Current Selection;Mass Flow Rate;Temperature;Density;Volume Flow Rate;Viscosity;Differential Pressure;Differential Pressure;Event1;Event2
583	Current primary variable selection is event2. Select Primary Variable:
584	Current secondary variable selection is mass flow rate. Select Secondary Variable:
585	Current secondary variable Selection is temperature. Select Secondary Variable:
586	Current secondary variable selection is density. Select Secondary Variable:
587	Current secondary variable selection is volume flow rate. Select Secondary Variable:
588	Current secondary variable selection is viscosity Select Secondary Variable:
589	Current secondary variable selection is differential Pressure Select Secondary Variable:
590	Current secondary variable selection is event1. Select Secondary Variable:
591	Current secondary variable selection is event2. Select Secondary Variable:
592	alarmNum
593	Start Sensor Zero;Reset Mass Total;Reset Volume Total;Reset Petroleum Reference Volume;Reset All Totals;Reset Concentration Reference Volume;Reset Concentration Net Mass;Reset Concentration Net Volume;Start/Stop Totals;Increment Concentration Curve;Print Screen;Print custody transfer screen;Reset Gas Standard Volume Total
594	Starting meter verification, please wait.
595	Meter verification completed: %{0}%
596	Meter verification PASS.
597	Meter verification FAILED.
598	Meter verification error.
599	Meter verification error. %{0}
600	Meter Verification will hold outputs at last value for about 2 minutes. Press Next to Start or Cancel to End.
601	Discrete output level is off.
602	Discrete output 1 level is on.
603	fValue
604	Current Primary Variable Selection is %0 Select Primary Variable:
605	Current Secondary Variable Selection is %0 Select Secondary Variable:
606	Priority: Failed - Fix Now Description: Continuity failure of drive circuit, LPO, or RPO, or LPO-RPO mismatch when driving. Recommended Actions: 1. Check for slug flow. 2. Check the test points. 3. Check the sensor circuitry. 4. Check sensor tubes for plugging. 5. If the problem persists, contact Micro Motion.
607	Drive Gain: Value %0
608	Priority: Failed - Fix Now Description: The value computed for the resistance of the line RTD or the Meter/Case RTD is outside limits. Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. If the problem persists, contact Micro Motion
609	Temperature: Value %0
610	Priority: Failed - Fix Now Description: The measured flow has exceeded the maximum flow rate of the sensor. Recommended Actions: 1. If other alerts are present (typically, A003, A006, A008, A102, or A105), resolve those alerts first. If the A005 alert persists, continue with the suggestions below. 2. Verify process and check for slug flow. 3. Check the test points 4. Check the sensor circuitry. 5. Check the sensor tubes for erosion. 6. If the problem persists, contact Micro Motion.
611	No Additional Information Available
612	Priority: Failed - Fix Now Description: One or more required characterization parameters have not been entered. Recommended Actions: 1. Check the characterization. Specifically, verify the FCF and K1 values. 2. If the problem persists, contact Micro Motion
613	Flow Cal: Value %0 K1: Value %1 uSec K2: Value %2 uSec
614	Flow FCF: Value %0 K1: Value %1 uSec K2: Value %2 uSec
615	Priority: Failed - Fix Now Description: The measured density has exceeded 0-10 g/cm3. Recommended Actions: 1. If other alerts are present (typically, A003, A006, A102, or A105), resolve those alerts first. If the A008 alert persists, continue with the suggestions below. 2. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes. 3. Check for slug flow. 4. Check the sensor circuitry. 5. Verify calibration factors in transmitter configuration. 6. Check the test points. 7. If the problem persists, contact Micro Motion
616	Priority: Failed - Fix Now Description: Transmitter in power-up mode. Recommended Actions: XX
617	Priority: Failed - Fix Now Description: Mechanical zero: The resulting zero was greater than 3 microseconds Temperature or Density Calibrations: many possible causes Recommended Actions: 1. If alert appears during a transmitter zero, ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
618	Priority: Failed - Fix Now Description: Mechanical zero: Calibration procedure failed due to reverse flow through the sensor. Recommended Actions: 1. Ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
619	Priority: Failed - Fix Now Description: Mechanical zero: Calibration procedure failed due to flow through the sensor.The resulting zero was greater than 3 microseconds. Recommended Actions: 1. Ensure that there is no flow through the sensor, then retry. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
620	Priority: Failed - Fix Now Description: Mechanical zero: The resulting zero was greater than 3 microseconds. Recommended Actions: 1. Remove or reduce sources of electromechanical noise, then retry. Sources of noise include mechanical pumps, pipe stress at sensor, electrical interference, or vibration effects from nearby machinery. 2. Cycle power to the flowmeter, then retry. 3. If appropriate, restore the factory zero to return the flowmeter to operation.
621	Priority: Failed - Fix Now Description: Many possible causes. Recommended Actions: 1. Cycle power to the flowmeter. 2. The transmitter might need service. Contact Micro Motion.
622	Priority: Failed - Fix Now Description: The value computed for the resistance of the Line RTD is outside limits. Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. Check the characterization. Specifically, verify the FCF and K1 values 4. If the problem persists, contact Micro Motion.
623	Priority: Failed - Fix Now Description: The value computed for the resistance of the Meter/Case RTD is outside limits. Recommended Actions: 1. Check the sensor RTD circuitry. 2. Verify that process temperature is within range of sensor and transmitter. 3. Check the characterization. Specifically, verify the FCF and K1 values 4. If the problem persists, contact Micro Motion.
624	Priority: Failed - Fix Now Description: The transmitter has experienced an EEPROM checksum failure. Recommended Actions: 1.Cycle power to the transmitter. 2.If problem persists, call Micro Motion.
625	Priority: Failed - Fix Now Description: A RAM location in the transmitter cannot be written to. Recommended Actions: 1.Cycle power to the transmitter. 2.If problem persists, call Micro Motion.
626	Priority: Failed - Fix Now Description: The flow calibration factor and/or K1 has not been entered since the last master rese Recommended Actions: 1. Check the characterization. Specifically, verify the FCF and K1 values. 2. If the problem persists, contact Micro Motion.
627	Priority: Failed - Fix Now Description: The sensor is recognized as a straight tube but the K1 value indicates a curved tube, or vice versa. Recommended Actions: 1. Check the characterization. Specifically, verify the FCF and K1 values. 2. Check the sensor RTD circuitry. 3. If the problem persists, contact Micro Motion.
628	Priority: Failed - Fix Now Description: Uncorrectable checksum mismatch. Recommended Actions: 1. Cycle power to the flowmeter. 2. The transmitter might need service. Contact Micro Motion.
629	Priority: Failed - Fix Now Description: Communication errors between transmitter and core processor. Recommended Actions: 1. Verify the wiring between the Transmitter and Core Processor. 2. Cycle power to the transmitter. 3. If problem persists, call Micro Motion.
630	Priority: Failed - Fix Now Description: Weights and Measures security seal has been broken. Recommended Actions: 1. Alarm can be cleared by user, but authorized procedure is required to reestablish security.
631	Priority: Failed - Fix Now Description: An attempt to write data to the core processor has failed. Recommended Actions: 1. Cycle power to the flowmeter. 2. The transmitter might need service or upgrading. Contact Micro Motion.
632	Priority: Failed - Fix Now Description: The core processor is not receiving enough power. Recommended Actions: 1. Check the power supply and all power wiring.
633	Priority: Failed - Fix Now Description: Meter verification is in progress, with outputs set to fault. Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to last measured value.
634	Priority: Failed - Fix Now Description: Meter verification is in progress, with outputs set to fault or last measured value. Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to continue measuring.
635	Priority: Failed - Fix Now Description: No signal from Left Pickoff or Right Pickoff, suggesting that sensor tubes are not vibrating. Recommended Actions: 1. Verify process. Check for air in the flow tubes, tubes not filled, foreign material in tubes, or coating in tubes.
636	Priority: Failed - Fix Now Description: Meter Verification Failed. Recommended Actions: 1. The test result is not within acceptable limits. Micro Motion recommends that you immediately re-run the meter verification test with outputs held at fault or last measured value. If the meter passes the second test, the fail result can be ignored. If the meter fails the second test, the flow tubes may be damaged. Use the knowledge of your process to consider the type of damage and determine the appropriate action. These actions might include removing the meter from service and physically inspecting the tubes. At a minimum, perform a flow validation and a density calibration.
637	Meter Verification Run Counter: %0 Transmitter Running Hours at Test: %1 Left Pickoff Stiffness: %2
638	Right Pickoff Stiffness: %0
639	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: User Initiated Abort Recommended Actions: Wait for 15 seconds before starting meter verification again.
640	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: Frequency Drift Recommended Actions: Ensure temperature, flow and density are stable and run meter verification again.
641	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: High Drive Gain Recommended Actions: Ensure flow is steady and minimize entrained gas and run meter verification again.
642	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: Unstable Flow Recommended Actions: Reduce flow rate and run meter verification again.
643	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: No Air Reference Recommended Actions: Perform factory calibration on air.
644	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: No Water Reference Recommended Actions: Perform factory calibration on water.
645	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: Missing Configuration Recommended Actions: Load verification parameter registers with proper values.
646	Priority: Failed - Fix Now Description: Meter Verification Aborted. Reason: Other Recommended Actions: Run meter verification again. If abort persists, call Micro Motion customer support.
647	Meter Verification Run Counter: %0 Transmitter Running Hours at Test: %1 Abort Code: %2
648	Left Pickoff Stiffness: %0 Right Pickoff Stiffness: %1
649	Priority: Advisory Description: The calculated amount of current output is outside of the linear range. Recommended Actions: 1. Verify that mA output range values are set to appropriate values.
650	Primary Variable: %0 %0: Value %1 %2
651	PV LRV: Value %0 %1 PV URV: Value %2 %3
652	Priority: Advisory Description: Non-zero HART address configured, or user has set the mA output to a fixed value. Recommended Actions: 1. Check the HART address. If non-zero, set mA Output Action parameter to enable Live mA Output. 2. Exit mA output trim. 3. Exit mA output loop test. 4. Check to see if the output has been fixed via digital communications.
653	HART Address: %0 mAO Fault Action: %1
654	Priority: Maintenance - Fix Soon Description: The drive power (current/voltage) is at its maximum. Recommended Actions: 1. Check the sensor circuitry. 2. If this is the only active alarm, it can be ignored. If desired, reconfigure the alarm severity to Ignore.
655	Priority: Maintenance - Fix Soon Description: The core processor was unable to successfully store the totalizers and inventories on the last power down and must rely on the previously saved values. These values may be up to two hours old. Recommended Actions: 1. Contact Micro Motion to upgrade the transmitter software. Note: The transmitter is still functional.
656	Priority: Advisory Description: A calibration procedure is in progress. Recommended Actions: 1. Allow the flowmeter to complete calibration. 2. For zero calibration procedures, you may abort the calibration, set the zero time parameter to a lower value, and restart the calibration.
657	Priority: Maintenance - Fix Soon Description: The density has exceeded the user-defined slug (density) limits. Recommended Actions: 1. Check that sensor is completely full. 2. Check that slug limits are set to appropriate values.
658	Slug High Limit: Value %0 g/Cucm Slug Low Limit: Value %1 g/Cucm Slug Duration: Value %2 sec Left Pickoff Amplitude: Value %3 V Right Pickoff Amplitude: Value %4 V Drive Gain: Value %5 %
659	Priority: Advisory Description: Device is in HART burst mode. Recommended Actions: 1. No action required. 2. If desired, reconfigure the alarm severity to Ignore.
660	Priority: Maintenance - Fix Soon Description: Transmitter has been restarted. Recommended Actions: 1. No action required.
661	Priority: Maintenance - Fix Soon Description: Event 1 has been triggered. Recommended Actions: 1. No action required. 2. If desired, reconfigure the alarm severity to Ignore.
662	Event 1 Setpoint: Value %0 Event 1 Variable: %1 Event 1 Type: %2
663	Priority: Maintenance - Fix Soon Description: Event 2 has been triggered. Recommended Actions: 1. No action required. 2. If desired, reconfigure the alarm severity to Ignore.
664	Event 2 Setpoint: Value %0 Event 2 Variable: %1 Event 2 Type: %2
665	Priority: Advisory Description: Process variable assigned to frequency output is outside configured scale limits. Recommended Actions: 1. Change frequency output scaling factors to more appropriate settings.
666	Third Variable: %0 %0: Value %1 %2
667	Rate Factor: Value %0 Hz Pulses/Unit: Value %1 Units/Pulse: Value %2
668	Priority: Advisory Description: User has set the frequency output to a fixed value. Recommended Actions: 1. Exit frequency output loop test.
669	Tube Frequency: Value %0 Hz
670	Priority: Advisory Description: User has set the mA output to a fixed value. Recommended Actions: 1. Exit mA output trim. 2. Exit mA output loop test. 3. Check to see if the output has been fixed via digital communications.
671	Priority: Maintenance - Fix Soon Description: No response received from polled device. Recommended Actions: 1. HART polling connection to external device has failed. Ensure that external device is available: 2. Verify device operation. 3. Verify wiring. 4. Verify polling configuration.
672	Poll Control: %0 Ext Device Tag 1: %1 Polled Variable 1: %2
673	Ext Device Tag 2: %0 Polled Variable 2: %1
674	Priority: Maintenance - Fix Soon Description: The process temperature is outside Petroleum Measurement defined extrapolation limits. Recommended Actions: 1. Verify process. 2. Verify configuration for Petroleum Measurement reference table and temperature.
675	Priority: Maintenance - Fix Soon Description: The process density is outside Petroleum Measurement defined extrapolation limits. Recommended Actions: 1. Verify process. 2. Verify configuration for Petroleum Measurement reference table and density.
676	Priority: Advisory Description: The user has set the discrete output to a fixed state. Recommended Actions: 1. No action required. 2. If desired, reconfigure the alarm severity to Ignore.
677	Priority: Advisory Description: The configured density/temperature/concentration values do not result in a proper Concentration Measurement (CM) curve. Recommended Actions: 1. Verify Concentration Measurement (CM) configuration.
678	Priority: Maintenance - Fix Soon Description: The process temperature or density is outside the user-defined extrapolation limits. Recommended Actions: 1. Verify the process temperature and density. 2. Verify Concentration Measurement (CM) configuration.
679	Priority: Maintenance - Fix Soon Description: Meter verification in progress, with outputs set to last measured value. Recommended Actions: 1. Allow the procedure to complete. 2. If desired, abort the procedure and restart with outputs set to fault.
680	Priority: Maintenance - Fix Soon Description: Meter verification in progress. Recommended Actions: 1. Allow the procedure to complete. You may abort the procedure if desired.
681	Priority: Advisory Description: Simulation mode is enabled. Recommended Actions: 1. Disable output simulation.
682	Priority: Advisory Description: Discrete Event 1 has been triggered. Recommended Actions: 1. No action required.
683	Discrete Event Var: %0 Discrete Event Type: %1
684	Setpoint A: Value %0 Setpoint B: Value %1
685	Priority: Advisory Description: Discrete Event 2 has been triggered. Recommended Actions: 1. No action required.
686	Priority: Advisory Description: Discrete Event 3 has been triggered. Recommended Actions: 1. No action required.
687	Priority: Advisory Description: Discrete Event 4 has been triggered. Recommended Actions: 1. No action required.
688	Priority: Advisory Description: Discrete Event 5 has been triggered. Recommended Actions: 1. No action required.
689	Priority: Advisory Description: Discrete Input is active. Recommended Actions: 1. No action required.
690	Priority: Maintenance - Fix Soon Description: Primary variable has exceeded sensor limits. Recommended Actions: 1. Verify process and check for slug flow. 2. Check the test points. 3. Check the sensor circuitry 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
691	Priority: Maintenance - Fix Soon Description: Non-primary variable has exceeded sensor limits. Recommended Actions: 1. Verify process and check for slug flow. 2. Check the test points. 3. Check the sensor circuitry 4. Check the sensor tubes for erosion. 5. If the problem persists, contact Micro Motion.
692	Priority: Maintenance - Fix Soon Description: The calculated amount of current output is outside of the linear range. Recommended Actions: 1. Verify that mA output range values are set to appropriate values.
693	Priority: Maintenance - Fix Soon Description: Power has been removed and reapplied resulting in the reinstallations of the setup information. Recommended Actions: 1. The first command to recognize this condition will automatically reset this flag. 2. This flag may also be set following a Master Reset or a Self Test.
694	Priority: Maintenance - Fix Soon Description: A write or set command has been executed. Recommended Actions: 1. No action required.
695	Priority: Maintenance - Fix Soon Description: A hardware error or failure has been detected by the device. Recommended Actions: 1. Check the test points. 2. Check the sensor circuitry. 3. If the problem persists, contact Micro Motion.
696	Priority: Failed - Fix Now Description: An uncorrectable checksum mismatch has been detected. Recommended Actions: 1. Cycle power to the flow meter. 2. The flow meter might need service. Contact Micro Motion.
697	Priority: Failed - Fix Now Description: ROM checksum error or a RAM location cannot be written to. Recommended Actions: 1. Cycle power to the flowmeter. 2. The flow meter might need service. Contact Micro Motion.
698	Test Result #%{Datalog_Index} Test Result Number: %0 Running Hours: %1 Test Result: %2 Abort Code %3 LPO Stiffness: %4 RPO Stiffness: %5
699	Priority: Failed - Fix Now Description: Transmitter electronics failure has occurred. Recommended Actions: 1. Cycle power to the flowmeter. 2. Contact Micro Motion.
700	Priority: Failed - Fix Now Description: The loaded software is not compatible with the programmed board type. Recommended Actions: 1. Contact Micro Motion.
701	To reset all matrix press Next or press Cancel.
702	All matrix data has been set to 0.
703	Concentration Measurement screen needs to be refreshed.
704	To reset all matrix data, press OK. Otherwise, press Abort.
705	The concentration matrix is locked, please unlock the matrix to configure.
706	number
707	Coil Value is %0 and Exception Code is %1
708	Unsigned 16 Value is %0 and Exception Code is %1
709	Unsigned 32 Value is %0 and Exception Code is %1
710	Floating Point Value is %0 and Exception Code is %1
711	Register is read-only.
712	uValue
713	Redefinindo a sinalizaÃ§Ã£o de configuraÃ§Ã£o alterada. Aguarde.
714	A sinalizaÃ§Ã£o de configuraÃ§Ã£o alterada foi reinicializada.
715	Select the matrix being configured:
716	Curve 1;Curve 2;Curve 3;Curve 4;Curve 5;Curve 6
717	Access Restricted
718	Resetting device. Please wait.
719	ReinÃcio do dispositivo concluÃdo com sucesso.
720	VocÃª vai sobregravar a config do dispositivo com valores de fÃ¡brica. Antes de continuar, defina o circuit de contr para oper manual e garanta que os val de config existentes sejam document ou salvos em arquivo. Se perder conexÃ£o do dispositivo, reconecte com padrÃµes. Continuar?
721	Aborting due to field device error
722	Factory values are restored successfully.
Reference ID	String