Device dictionary

Loading…

Reference ID	String
0	82TC CONC
1	Toroidal Concentration Transmitter
2	ABB Instrumentation
3	EC1 HI.PV.AD
4	Process Variable A/D over range
5	EC2 LO.PV.AD
6	Process Variable A/D under range
7	EC3 PH.PCB
8	pH/ORP/pION input PCB with Conductivity/concentration firmware
9	EC6 TE.PCB
10	2-electrode conductivity input PCB with Toroidal conductivity/concentration firmware
11	EC7 EC.PCB
12	Electrode conductivity input PCB with Toroidal conductivity/concentration firmware
13	PC6 HI.LOOP
14	Current loop above upper range
15	PC7 LO.LOOP
16	Current loop below lower range value
17	PC8 HI.PV
18	PV above transmitter range
19	PC9 LO.PV
20	PV below transmitter range
21	PC10 HI.TEMP
22	Temperature above transmitter range
23	PC11 LO.TEMP
24	Temperature below transmitter range
25	PC12 HI.T.AD
26	Open or missing Temperature Sensor
27	PC13 LO.T.AD
28	Shorted Temperature Sensor
29	PC2O BAD.SEE
30	Bad SEEPROM or bad input PCB assembly
31	PC21 NO.F.CAL
32	Missing factory cal or nonfunctional SEEPROM
33	PC22 BLNK.EE
34	Blank microprocessor EEPROM
35	PC25 ROM.SUM
36	Incorrect EPROM checksum
37	PC30 R0.F.CAL
38	Out of range or missing factory cal for conductivity circuit range zero
39	PC31 R1.F.CAL
40	Out of range or missing factory cal for conductivity circuit range one
41	PC32 R2.F.CAL
42	Out of range or missing factory cal for conductivity circuit range two
43	PC33 R3.F.CAL
44	Out of range or missing factory cal for conductivity circuit range three
45	PC34 R4.F.CAL
46	Out of range or missing factory cal for conductivity circuit range four
47	PC45 BA.F.CAL
48	Out of range or missing factory cal for 3-k ohm Balco temp.compensator
49	PC46 PT.F.CAL
50	Out of range or missing factory cal for PT100 temp. compensator
51	PC48 PK.F.CAL
52	Out of range or missing factory cal for PT1000 temp. compensator
53	PC50 R0.CHKS
54	Incorrect or missing conductivity circuit range zero checksum
55	PC51 R1.CHKS
56	Incorrect or missing conductivity circuit range one checksum
57	PC52 R2.CHKS
58	Incorrect or missing conductivity circuit range two checksum
59	PC53 R3.CHKS
60	Incorrect or missing conductivity circuit range three checksum
61	PC54 R4.CHKS
62	Incorrect or missing conductivity circuit range four checksum
63	PC65 BA.CHKS
64	Incorrect or missing 3-k ohm Balco temp. compensator checksum
65	PC66 PT.CHKS
66	Incorrect or missing PT100 temp. compensator checksum
67	PC68 PK.CHKS
68	Incorrect or missing PT1000 temp. compensator checksum
69	PV was unstable during PV cal
70	PV value was unstable during PV calibration
71	PV was drifting during PV cal
72	PV value was drifting during PV calibration
73	PV LO OFFSET
74	PV calibration Offset too low
75	PV LO SLOPE
76	PV calibration Slope too low
77	PV HI OFFSET
78	PV calibration Offset too high
79	PV HI SLOPE
80	PV calibration Slope too high
81	Temp Offset Warning
82	Temperature calibration Offset unacceptable
83	Temp Slope Warning
84	Temperature calibration Slope unacceptable
85	In PV Cal mode
86	A PV zero or span point calibration is being performed on the device
87	PV eng. unit
88	ppb
89	Parts per Billion
90
91	Concentration - Field Device Variable Digital value that changes magnitude with respect to time with no user intervention.
92	.3f
93	.2f
94	8.2f
95	11.3f
96	8u
97	Temp Unit
98	Temperature- In Auto temp comp mode, it is the Temp read with the temp sensor. In Manual temp comp mode, it is the user entered temp value
99	In calibration security mode
100	Transmitter Busy - Cannot Process Command
101	10.3f
102	PV slope
103	PV sensor slope value
104	PV offset
105	PV sensor offset value.
106	Temperature sensor Slope
107	Temperature sensor offset
108	Temperature sensor offset value.
109	Span point value
110	Span calibration point value for PV calibration
111	Temp. calibration value
112	Temperature calibration value
113	Zero point value
114	Zero calibration point value
115	Concentration cal
116	HART Parameters
117	Offline Configuration Parameters
118	PV Range Setup
119	Reset Transmitter
120	Reset Transmitter - Instructs the transmitter to generate a reset. The result is similar to the effects of briefly interrupting power to the transmitter. This can be used to recover from an error condition if needed.
121	Zero point cal
122	Calibration of the process sensor input via a Zero-Point offset calibration
123	Span point cal
124	Calibration of the process sensor input via a Span-Point slope calibration
125	Read cal values
126	Temp. Cal
127	Calibration of Temperature sensor input via one-point smart calibration that adjusts offset and slope
128	Edit Cal
129	Manual adjustment of process sensor and temperature offset and slope values
130	Reset Cal
131	Reset the process and temperature sensor calibration data to the values set at the factory
132	Refresh variables
133	Read transmitter variables to refresh their values. This will update any variable that was modified via the device keypad.
134	FMU860
135	DT
136	DVC
137	FCX
138	AS800
139	340T
140	340C
141	344
142	Siemens Micro K
143	SITRANS L
144	SIPAN PH
145	SITRANS P
146	75SMT
147	UNIDELTA
148	8320
149	SX5100
150	TSV175
151	DMU
152	3780
153	BM70
154	low
155	high
156	tmp_av
157	Transmitter will be Reset! Continue?
158	Transmitter Reset is in process, please wait.
159	Reading current values of all transmitter variables, please wait.
160	Transmitter Reset successful
161	Access denied PV cal in progress
162	Zero cal point: %{4} %{3} Press OK to continue
163	Press OK when PV is stable %0 %{3}
164	Waiting for calibration
165	PV was DRIFTING during PV cal
166	PV was UNSTABLE during PV cal
167	Calculated Slope:%{1} Offset:%{2}
168	REJECT;ACCEPT
169	PV cal completed Slope: %{1} Offset: %{2}
170	Calibration was not successful. Do you want to retry?
171	Enter Span cal point
172	Enter Temperature:
173	TEMP OFFSET WARNING
174	TEMP SLOPE WARNING
175	Edit PV Slope
176	Edit PV Offset
177	Edit Temp. Slope
178	Edit Temp. Offset
179	Press OK to Reset Calibration
180	Reading transmitter variables, please wait.
Reference ID	String