Device dictionary

Loading…

Reference ID	String
0	FVS4000
1	Error 120%QmaxDN
2	Kit-Fram
3	Backup Database
4	Error steam
5	Front End
6	Error flow >103%
7	Error Dbase
8	Error totalizer
9	Error temperature
10	Max alarm flow
11	Min alarm flow
12	Error reg alarm
13	Max alarm Temp
14	Min alarm Temp
15	Pulse factor lim
16	Pulse width lim.
17	Totalizer unit
18	Low flow cutoff
19	Selfcheck contact
20	Selfcheck flow
21	Selfcheck Iout
22	Device setup
23	AO1
24	Process variab. 2
25	Special Commands
26	Primary
27	Calculation
28	Input/Output
29	Display
30	Unit
31	Totalizer
32	Pulse output
33	Current output
34	Alarm
35	PT100
36	Service Parameter
37	DSP
38	VIB
39	Standard
40	Spectrum
41	Diagnostic
42	Error bytes
43	Status bytes
44	Adjust
45	k-factor
46	f Liquid
47	k Liquid
48	f Gas
49	k Gas
50	Flow Unit volume or mass
51	Flow Unit
52	Unit Qvol
53	Volume Flow Unit
54	Unit Qm
55	Mass Flow Unit
56	Totl.Unit
57	Totalizer unit for volume and mass flow
58	Unit vol.totl.
59	Available units for vol.flow totalizer.
60	Unit mass totl.
61	Available units for mass flow totalizer.
62	Density unit
63	Available units for density.
64	Temperature unit
65	Temperature Unit Help
66	Temperature unit
67	Qv
68	Qm
69	Qn
70	Qs
71	Flow Q in specified flow mode.
72	.2f
73
74	Qop
75	Volume Flow
76	Standard Flow
77	Mass Flow Qm
78	Totl
79	Totalizer. Integral of flow.
80	Totl
81	T
82	Help Temperature
83	.1f
84	p
85	Help Pressure
86	F
87	Frequency of whirl in primary.
88	Freq
89	%
90	Percent of flow
91	Q%
92	Q
93	Tot
94	Reset Conf.Changed
95	Totalizer reset
96	Reset Err.register
97	Primary
98	Primary can be selected as a Vortex or swirl type
99	Swirl ST/SR
100	Vortex VT/VR
101	Metersize Swirl
102	Selection of swirl type primary meter size
103	15 mm 1/2 in
104	20 mm 3/4 in
105	25 mm 1 in
106	32 mm 1-1/4 in
107	40 mm 1-1/2 in
108	50 mm 2 in
109	80 mm 3 in
110	100 mm 4 in
111	150 mm 6 in
112	200 mm 8 in
113	300 mm 12 in
114	400 mm 16 in
115	Metersize Vortex
116	Selection of Vortex type primary meter size
117	DIN 15mm 0.5in
118	DIN 25mm 1in
119	DIN 40mm 1.5in
120	DIN 50mm 2in
121	DIN 80mm 3in
122	DIN 100mm 4in
123	DIN 150mm 6in
124	DIN 200mm 8in
125	DIN 250mm 10in
126	DIN 300mm 12in
127	ANSI 15mm 0.5in
128	ANSI 25mm 1in
129	ANSI 40mm 1.5in
130	ANSI 50mm 2in
131	ANSI 80mm 3in
132	ANSI 100mm 4in
133	ANSI 150mm 6in
134	ANSI 200mm 8in
135	ANSI 250mm 10in
136	ANSI 300mm 12in
137	Flow mode
138	Different selections for operating mode of the instrument depends on setting of enable k-set and PT100 sensor
139	Gas Qv
140	Gas Stnd Qs (Cmp)
141	Gas MassQm (pD)
142	Gas Norm Qn (pT)
143	Gas Stnd Qs (pT)
144	Gas MassQm (pT)
145	steam satu.Qm
146	steam satu.Qv
147	Liquid Qv
148	Liquid Qm (D)
149	Liquid Qm (D,T)
150	Liquid Qm (V,T)
151	Normal condi.
152	Standard conditions for pressure and temperature at calculation
153	1.0133bara 0C
154	1.0133bara 20C
155	Language
156	Available languages on the instrument display for textes.
157	German
158	English
159	Main display
160	Select the parameter to be shown on the instrument display.
161	Q flow mode
162	Qv operate
163	Percent
164	Frequency
165	Temperature
166	Multipl.display
167	Select the parameter to be shown multiplexed on the instrument display.
168	2.Line multi.
169	Multiplex display on/off
170	Hardware Config.
171	Hardware configuration
172	I/Hart
173	I/Hart/ Puls_Bin
174	I/Hart/ Q_Alarm
175	I/Hart/ T_Alarm
176	I/Hart/ S_Alarm
177	k-linearisation
178	Modes for k-factor linearisation.
179	Mean value
180	5 points
181	Enable K-Set
182	Modes for k-factor-set
183	Gas
184	Liquid
185	Liquid & Gas
186	PT100 Sensor
187	enable/disable PT100 sensor
188	off
189	on
190	Boot Page
191	Boot Page: Standard or Spectrum !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
192	Spectrum
193	Freq. Min
194	Frequency minimum !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
195	954 Hz
196	477 Hz
197	238 HZ
198	119 Hz
199	60 Hz
200	30 Hz
201	15 Hz
202	8 Hz
203	4 Hz
204	2 Hz
205	1 Hz
206	Freq. Max
207	Frequency maximum !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
208	2500 Hz
209	954 Hz
210	477 HZ
211	238 Hz
212	119 Hz
213	60 Hz
214	30 Hz
215	15 Hz
216	8 Hz
217	4 Hz
218	2 Hz
219	Freq.Spec.Bal.
220	Frequency Spec. Balance !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
221	Off
222	1
223	2
224	3
225	BP-Aver.Damp
226	BP - Average Damping !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
227	1.0 s
228	2.0 s
229	5.0 s
230	.4f
231	col uc_var
232	help unsigned char variables
233	Instrument no.
234	Instrument number.
235	5u
236	Description geraetenummer
237	Overflow
238	Number of totalizer overflows. Please refer to instruction book for more information.
239	mains interrupt
240	Number of power supply interruptions since starting up the instrument.
241	Temp.Interv
242	Temperature interval . !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
243	Gain Max
244	Gain max !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
245	GainVibTrg
246	Gain Vib Trigger !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
247	LowDisGain
248	Low Dis Gain !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
249	HighDisGain
250	High Dis Gain !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
251	col ui_var
252	help ui variables
253	QmaxDN operat.
254	Maximum flow value of metersize at operation mode
255	8.2f
256	Qmax
257	Upper span value
258	Qmin operat.
259	Low flow cutoff-value
260	Reference temp
261	Value for temperature at operation conditions
262	8.3f
263	Pressure Popr abs
264	Value for pressure at operation conditions
265	Compressibility
266	Factor for flow calculation due to standard conditions.
267	Normal density
268	Value for density at normal conditions for massflow calculation.
269	Reference density
270	Value for density at operation conditions for massflow calculation.
271	Vol.extension
272	Volume extension of liquids as a function of temperature.
273	‰/K
274	Density Extension
275	Density extension of liquids as a function of temperature.
276	%./K
277	Pulse factor
278	Value of pulse factor for totalizer calculation.
279	Edit Pulse factor
280	Edit Pulse width
281	Value of pulse width for pulse output.
282	Pulse width
283	ms
284	7.3f
285	Damping
286	Time constant for current output damping.
287	5.2f
288	Iout at Alarm
289	Alarm current
290	Max Q-Alarm
291	Help max Q-Alarm
292	6.2f
293	Min Q-Alarm
294	Help min Q-Alarm
295	Max T-Alarm
296	Help max T-Alarm
297	Min T-Alarm
298	Help min T-Alarm
299	Adjust Iout 4 mA
300	Adjust 4 mA current output value. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
301	6.3f
302	Adjust Iout 20 mA
303	Adjust 20 mA current output value. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
304	Temp.correct
305	temperature correction !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
306	L mean k-factor
307	Mean k-factor value of primary, Please refer to the calibration protocol. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
308	8.1f
309	L k1
310	K-factor k1 is related to frequency f1. Please refer to calibration protocol! !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
311	L k2
312	K-factor k2 is related to frequency f2. Please refer to calibration protocol! !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
313	L k3
314	K-factor k3 is related to frequency f3. Please refer to calibration protocol! !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
315	L k4
316	K-factor k4 is related to frequency f4. Please refer to calibration protocol! !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
317	L k5
318	K-factor k5 is related to frequency f5. Please refer to calibration protocol! !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
319	L f1
320	Frequency point liquid f1 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
321	L f2
322	Frequency point liquid f2 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
323	L f3
324	Frequency point liquid f3 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
325	L f4
326	Frequency point liquid f4 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
327	L f5
328	Frequency point liquid f5 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
329	G mean k-factor
330	G k1
331	G k2
332	G k3
333	G k4
334	G k5
335	G f1
336	Frequency point g_f1 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
337	G f2
338	Frequency point g_f2 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
339	G f3
340	Frequency point g_f3 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
341	G f4
342	Frequency point g_f4 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
343	G f5
344	Frequency point g_f5 for k-factor linearisation. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
345	Input min.
346	Input minimum. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
347	Vib Qv fact
348	Vib Qv factor. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
349	LowDisFreq
350	Low Dis Frequency. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
351	HighDisFreq
352	High Dis Frequency. !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
353	col fl_var
354	float variables index
355	Amplificat.
356	Bp0 output
357	!! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
358	TempMeas cnt
359	Bp1 output
360	FreqMeas cnt
361	Freq.Meas count !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
362	BP status
363	BP status !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
364	No AD-Input
365	Vibrate Cut Off
366	Ini BP-Range
367	Range Flws Freq
368	IniVib In Meas
369	Vib In Meas
370	IniTmp In Meas
371	Tmp In Meas
372	Periods
373	Periods !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
374	Samples
375	Sampl/Per.
376	Bp2 output
377	AD input
378	AD input !! FOR SERVICE ONLY !! CHANGING OF SERVICE-PARAMETERS MAY HAVE AN EFFECT ON THE OPERATION OF THE PLANT, THE BUS COMMUNICATION AND MAY ENDANGER LIFES.
379	BP output
380	Bp3 output
381	BP-Freq.rel.
382	Bp4 output
383	Vib output
384	Bp5 output
385	.3f
386	FMU860
387	DT
388	DVC
389	FCX
390	AS800
391	340T
392	340C
393	344
394	Siemens Micro K
395	SITRANS L
396	SIPAN PH
397	SITRANS P
398	75SMT
399	UNIDELTA
400	8320
401	SX5100
402	TSV175
403	DMU
404	3780
405	BM70
406	8u
407	4.2f
408	7d
409	Sensor
410	Sensor Info
411	Input
412	Outputs
413	Analog Output
414	HART Output
415	Reset Configuration Changed Flag ?
416	Reset totalizer?
417	Reset error register and totalizer mains interrupt?
418	Write new pulse factor %{0}?
419	Converter changed input. New pulse factor %{0}
420	Converter changed pulsewidth to %{0} ms
421	Write new pulse width %{0} ms?
422	Converter changed input. New pulse width %{0} ms
Reference ID	String