Loading…
名称 ID 标签 描述 类型 访问 分类
cDensityUnits 4055 Density Units 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 读/写 枚举 32
dDensityValue 4056 Density 现场设备变量值——在没有用户干扰的条件下，根据时间改变大小的数值。 读/写 浮点 34
dDensityDamping 4149 Density Damping Factor 阻尼值——同时应用至各自模拟量输出的数值表示和模拟值的阻尼时间常数。该变量的单位始终为秒钟。 读/写 浮点 32
dDensityUpperSensorLimit 4057 密度URL 传感器上限值——定义上限值的最大可用数值。 读 浮点 8
dDensityLowerSensorLimit 4058 密度LRL 传感器下限值——定义上限值的最小可用数值。 读 浮点 8
dDensityMinimumSpan 4059 Minimum Span 最小范围值——定义上限值和下限值之间允许的最小差。 读 浮点 8
dDensityFrequency 4233 Frequency Value of variable given in frequency output 读 浮点 514
dDensityFreqRange 4234 Density Frequency Limit Pulse frequency at maximum flow rate 读/写 浮点 512
dDensityFreqPercent 4235 Frequency Percent Percent of maximum flow rate 读 浮点 34
sluglo 405D Slug Low Limit A programmable low limit on density, which enables the transmitter to indicate slug flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed slug flow limits. 读/写 浮点 8
slughi 405E Slug High Limit A programmable high limit on density, which enables the transmitter to indicate slug flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed slug flow limits. 读/写 浮点 8
slug_delay_time 4125 Slug Delay Time The time delay between the density exceeding the slug-flow thresholds and the slug-flow error being declared. 读/写 浮点 8
cTemperatureUnits 4061 Temperature Units 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 读/写 枚举 32
dTemperatureValue 4062 Temperature 现场设备变量值——在没有用户干扰的条件下，根据时间改变大小的数值。 读 浮点 34
dTemperatureUpperSensorLimit 4063 温度URL 传感器上限值——定义上限值的最大可用数值。 读 浮点 8
dTemperatureLowerSensorLimit 4064 温度LRL 传感器下限值——定义上限值的最小可用数值。 读 浮点 8
dTemperatureMinimumSpan 4065 Minimum Span 最小范围值——定义上限值和下限值之间允许的最小差。 读 浮点 8
dTemperatureFrequency 4236 Frequency Value of variable given in frequency output 读 浮点 514
dTemperatureFreqRange 4237 Temperature Frequency Limit Pulse frequency at maximum flow rate 读/写 浮点 512
dTemperatureFreqPercent 4238 Frequency Percent Percent of maximum flow rate 读 浮点 34
txvar_code 4158 读/写 索引 4096
dMassFlowFallback 400F Mass Flow Fallback Value assigned to the parameter when it can not be determined correctly due to process or system conditions. 读/写 浮点 32
dMassFlowHiAlarmSetpoint 4011 Mass Flow Hi Alarm Setpoint Assigns value, above which an alarm indication is given 读/写 浮点 1024
dMassFlowLowAlarmSetpoint 4010 Mass Flow Low Alarm Setpoint Assigns value, below which an alarm indication is given 读/写 浮点 1024
dMassFlowLfCutoff 4012 Mass Flow Low Flow Cutoff When the actual flow rate is below this value, the indicated flow rate goes to zero, and any outputs configured for this parameter will go the appropriate value. 读/写 浮点 8
名称 ID 标签 描述 类型 访问 分类