Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| self_test_658T | 408D | Xmtr Self Test | Commands the 658T to perform a self-test. Note: Analog output is affected during the test. | msrc_UNKNOWN | Details |
| zero_trim_658T | 408E | Lead Resist Trim | Trim the lead resistances so that the output reads zero, repectively reset the historical lead resistance value to 0. Used with 2-wire or dual RTD measurements only. | msrc_UNKNOWN | Details |
| reset_analog_trim | 408F | Reset Analog Trim | Reset the Analog Output to the factory settings. | msrc_UNKNOWN | Details |
| set_sensor_connection | 4090 | Select Sensor | Define the sensor type and the sensor connection. | msrc_UNKNOWN | Details |
| sensor_setup_method | 4091 | Sensor Setup Info | Displays the sensor type, linearization mode, sensor connection, and cold junction compensation. | msrc_UNKNOWN | Details |
| set_line_break_detection_method | 4092 | Sensor Fail Det. | Enable or disable the detection of a sensor failure or line break. | msrc_UNKNOWN | Details |
| exit_line_break_detection | 4093 | Exit Line Break Detection | msrc_UNKNOWN | Details | |
| set_characterization | 4094 | Snsr Offset Curve | Correction or characterization of input sensor(s). 2-22 pairs of values. | msrc_UNKNOWN | Details |
| correction_system_status | 4097 | Snsr Offset Curve | Display the status of the Sensor Offset Curve System. | msrc_UNKNOWN | Details |
| sensor_curve_system_off | 4095 | 特性化ﾓｰﾄﾞから出ます | msrc_UNKNOWN | Details | |
| exit_sensor_curve_setup | 4096 | 特性化ﾓｰﾄﾞから出ます | msrc_UNKNOWN | Details | |
| set_temp_comp | 4098 | msrc_UNKNOWN | Details | ||
| show_temp_comp_method | 4099 | msrc_UNKNOWN | Details | ||
| failsafe_report_method | 409A | Failsafe Report | Displays current failsafe setup. | msrc_UNKNOWN | Details |
| failsafe | 409B | Failsafe Report | Configuration of the mA output upon failsafe. | msrc_UNKNOWN | Details |
| exit_failsafe_setup | 409C | Exit Failsafe Setup | msrc_UNKNOWN | Details | |
| set_eng_units_method | 409D | Engineering Units | Set the engineering unit to be displayed with the Digital Value representation, Upper Range Value, Lower Range Value, and Lower Sensor Limit. | msrc_UNKNOWN | Details |
| exit_eng_units_setup | 409E | Exit Engineering Units Setup | msrc_UNKNOWN | Details | |
| set_line_freq | 409F | Line Freq & Filt | Set the power line frequency and filter. | msrc_UNKNOWN | Details |
| exit_line_freq_setup | 40A0 | Exit Line Freq & Filter Setup | msrc_UNKNOWN | Details | |
| enter_smartsmoothing_method | 40A1 | Smart Smoothing | Suppression of noise through averaging with fast response to 1-10 degC changes of the input. Min value - 0.25, Max value - 30. | msrc_UNKNOWN | Details |
| exit_ss_setup | 40A2 | Exit Smart Smoothing Setup | msrc_UNKNOWN | Details | |
| enter_validtime_method | 40A3 | Validation Time | Validation time sets the time interval for bad data suppression. Min value - 0.25, Max value - 10. | msrc_UNKNOWN | Details |
| exit_vtime_setup | 40A4 | Exit Validation Time Setup | msrc_UNKNOWN | Details | |
| enter_lrv_method | 40A5 | Set LRV | Specify the Lower Range Value, (the 4ma value). | msrc_UNKNOWN | Details |
| exit_lrv_setup | 40A6 | Exit LRV Setup | msrc_UNKNOWN | Details | |
| enter_urv_method | 40A7 | Set URV | Specify the Upper Range Value, (the 20ma value). | msrc_UNKNOWN | Details |
| exit_urv_setup | 40A8 | Exit URV Setup | msrc_UNKNOWN | Details | |
| apply_lrv | 40A9 | Apply LRV | Perform a device rerange by applying the 4ma value to the device input. | msrc_UNKNOWN | Details |
| apply_urv | 40AA | Apply URV | Perform a device rerange by applying the 20ma value to the device input. | msrc_UNKNOWN | Details |
| enter_damping_method | 40AB | Set Damping | Specify exponential damping of input signal, maximum time constant 32 seconds. | msrc_UNKNOWN | Details |
| exit_damping_setup | 40AC | Exit DAMPING Setup | msrc_UNKNOWN | Details | |
| enter_internaltemp_method | 40AD | Internal Temp Unit | Engineering units of the internal temperature of the device. | msrc_UNKNOWN | Details |
| exit_inttemp_setup | 40AE | Exit Internal Temp Unit Setup | msrc_UNKNOWN | Details | |
| exit_fixed_method | 40AF | Reset Failsafe Val | Clear latched Failsafe. | msrc_UNKNOWN | Details |
| acknowl_stat | 40B0 | Clear Hist Status | Clear the historical status information for failures. The historical status information is not automatically cleared when the failure is removed. They have to be cleared manually. | msrc_UNKNOWN | Details |
| pv_units_warning | 40B1 | warn | msrc_UNKNOWN | Details | |
| return_to_normal | 1016 | ﾉｰﾏﾙ ﾓｰﾄﾞに戻します | msrc_UNKNOWN | Details | |
| dac_trim | 1004 | Trim 4-20mA | D/A ﾄﾘﾑ (ﾃﾞｼﾞﾀﾙ/ｱﾅﾛｸﾞ ﾄﾘﾑ) - ｵﾍﾟﾚｰﾃｨﾝｸﾞ ｴﾝﾄﾞ ﾎﾟｲﾝﾄに対するｱﾅﾛｸﾞ出力と外部指示計とのｷｬﾘﾌﾞﾚｰｼｮﾝを行います。 | msrc_UNKNOWN | Details |
| loop_test | 1002 | ﾙｰﾌﾟ ﾃｽﾄ | ﾙｰﾌﾟ ﾃｽﾄ - ｱﾅﾛｸﾞ出力をﾕｰｻﾞｰが選択した値で固定出力します | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | 固定電流ﾓｰﾄﾞを終ります | 現在の固定ﾓｰﾄﾞを終了 - ｱﾅﾛｸﾞ出力を定数値のﾓｰﾄﾞから移行させ, 出力が入力に応じて変わるﾓｰﾄﾞに戻します。 | msrc_UNKNOWN | Details |
| Name | ID | Label | Description | Type | Source |