Device dictionary

Loading…

Reference ID	String
0	YOKOGAWA
1	EJX
2	Operate mode
3	Field Device Specific Operating Mode - A possible mode of operation in Field Device.
4	Device configuration locked
5	Device is in write-protect or is locked.
6	Burst OFF
7	Burst ON
8	inH2O @68degF
9	ftH2O @68degF
10	mmH2O @68degF
11	g/cm2
12	kg/cm2
13	ftH2O
14	Feet of Water at 4 Degrees Celsius
15	hPa
16	Hectopascals
17	Chg power on info- Change the information displayed when turn on the power.
18	Chg power on info
19	Abort of the Chg power on info- Display the power on information.
20	Abort of the Chg power on info
21	Chg universal rev- Change the universal command revision.
22	Chg universal rev
23	Abort of the Chg universal rev- Display the universal revision.
24	Abort of the Chg universal rev
25	Status group 1
26	P sensor error
27	CT sensor error
28	Cap EEPROM error
29	AT sensor error
30	Amp EEPROM error
31	Status group 2
32	CPU board error
33	No device ID
34	Status group 3
35	P outside limit
36	SP outside limit
37	CT outside limit
38	AT outside limit
39	Status group 4
40	P over range
41	SP over range
42	Status group 5
43	P high alarm
44	P low alarm
45	SP high alarm
46	SP low alarm
47	CT high alarm
48	CT low alarm
49	Status group 6
50	Illegal P LRV
51	Illegal P URV
52	Illegal P SPAN
53	P SPAN trim err
54	P ZERO trim err
55	Illegal SP LRV
56	Illegal SP URV
57	Illegal SP SPAN
58	Status group 7
59	SP SPAN trim err
60	SP ZERO trim err
61	SC config error
62	Status group 8
63	FT high alarm
64	FT low alarm
65	ILBD over range
66	Invalid Ref DP
67	Invalid Ref SPL
68	Invalid Ref SPH
69	Invalid Ref F
70	Status group 9
71	B Blocking
72	H Side Blocking
73	L Side Blocking
74	Large Fluct H
75	Large Fluct L
76	A Blocking
77	Status group 10
78	P.Simulate Mode
79	SP.Simulate Mode
80	T.Simulate Mode
81	.2f
82	.3f
83	.4f
84	.1f
85	.5f
86	.0f
87	.6f
88	Burst
89	Cmd 48: Read Additional Device Status
90	Read Additional Device - This command reads additional device status information
91	Event
92	Device status Mask
93	Device Status Mask
94	Status group 1 Mask
95	Device Specific Status 1 Mask
96	Status group 2 Mask
97	Device Specific Status 2 Mask
98	Status group 3 Mask
99	Device Specific Status 3 Mask
100	Status group 4 Mask
101	Device Specific Status 4 Mask
102	Status group 5 Mask
103	Device Specific Status 5 Mask
104	Status group 6 Mask
105	Device Specific Status 6 Mask
106	Ext dev status Mask
107	Extended Field Device Status Mask
108	Diagnostic status 0 Mask
109	Device Diagnostic Status 0 Mask
110	Diagnostic status 1 Mask
111	Device Diagnostic Status 1 Mask
112	AO fixed Mask
113	AO Fixed Mask
114	AO saturated Mask
115	AO Saturated Mask
116	Status group 7 Mask
117	Device Specific Status 7 Mask
118	Status group 8 Mask
119	Device Specific Status 8 Mask
120	Status group 9 Mask
121	Device Specific Status 9 Mask
122	Status group 10 Mask
123	Device Specific Status 10 Mask
124	Variable Code
125	Burst Variable Code
126	Update Period
127	Update period for burst message
128	Max Update Period
129	Maxium update period for burst message
130	Command
131	Mode
132	Trigger Mode
133	Burst Message Trigger Mode
134	Trigger Class
135	Burst Trigger Class
136	Trigger Units
137	Burst Trigger Units
138	Trigger Level
139	Burst Trigger Level
140	Status
141	Event Status
142	Control
143	Event Notification Control
144	1st Unack Time
145	Time First Unack Event Triggered
146	Retry Time
147	Event Notification Retry Time
148	Max Update Time
149	Debounce Interval
150	Event Debounce Interval
151	Squawk Control
152	Off
153	On
154	Squawk Once
155	Pres %
156	Pres Damp
157	6.2f
158	Si Oil
159	F Oil
160	Process Conn type
161	Thread
162	Num of RS
163	Two Seals
164	Extension
165	HTV-W
166	HTV-E
167
168	Data Quality
169	Limit Status
170	Update time period
171	Update time period help
172	Property
173	Device variable properties
174	P LTP
175	P UTP
176	AO alm typ
177	Hold Last Output Value
178	Enumeration May Be Used For Manufacturer Specific Definitions
179	Process Conn matl
180	Module type
181	DP
182	Pressure
183	Excess Correction Attemped
184	Not write protect mode
185	The First Password Accepted
186	Keypad input
187	Pres trim info.
188	SP sensor trim
189	SP trim info.
190	Trim info.
191	Diag Parameters
192	ILBD Parameters
193	Diag Variables
194	Diag Reference
195	Fluct Variables
196	Test
197	Configuration
198	Diag Lim
199	Diag Ref Lim
200	HT Parameters
201	Flg Temp Lim
202	Diag Output
203	Error log
204	SP Range
205	SP A/G Setup
206	SP sensor
207	Temp sensor
208	T.Z. Cmp menu
209	S.C. menu
210	Process Alerts
211	Config Pres Alerts
212	Config Temp Alerts
213	DO Config
214	Display condition
215	Disp select
216	P disp condition
217	SP disp condition
218	Engr disp range
219	Wrt protect menu
220	Pres sensor trim
221	Self Test- Commands the EJX electronics to perform a selftest. Reports any errors that occured.
222	Clear digital to analog trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
223	Clear D/A trim
224	Pressure trim- Executes full sensor trim with zero point adjustment by Lower Pt and span adjustment by Upper Pt.
225	Pres trim
226	Clear pressure sensor trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
227	Clear P snsr trim
228	Static pressure trim- Executes full sensor trim with zero point adjustment by Lower Pt and span adjustment by Upper Pt.
229	Static Pres trim
230	Clear static pressure sensor trim- Resets the trim adjustment to the initial calibrated values that were set at factory.
231	Clear SP snsr trim
232	Error log clear- Clears the error records.
233	Error log Clear
234	SP Apply values
235	Signal characterizer point setting- Sets the coordinates of break points to characterize the values in percent of the output.
236	Point setting
237	Digital output test- Allows the user to test the contact output for a digital signal at the contact output terminal of the device. Select 'On' to output the digital signal.
238	DO Test
239	Modify engineering unit- Modifies the engineering unit or sets a customized engineering unit. Enter a series of up to eight alphanumeric characters, spaces, or slashes (only first six characters are shown on LCD). Note that if you already select the unit at 'Set Engineering Unit,' the unit appears as a default. Then re-enter the unit but enter a space instead of a character to display the character in lowercase on LCD. For example, in order to show 'aBCd' on LCD, enter 'ABCD' first, then enter '_BC_'.
240	Modify Engr Unit
241	Test Key
242	Enable parameter change for 10 min.- releases the software write protection for 10 minutes when the password is entered.
243	Enable wrt 10min
244	New password- Sets or changes the password for software write protection.
245	New password
246	Aborting
247	Exiting
248	Set Diag Mode
249	Pres Zero trim
250	Error log view- Displays the error records from log1(latest) to log4.
251	Error log view
252	Set engineering unit- Selects the engineering unit from the list.
253	Set Engr Unit
254	Static Pressure- Pressure of the process measured with respect to the reference pressure equal to 0.
255	SP
256	Static pressure percent of range- Static Pressure Variable that tracks the Digital Value representation with respect to the range defined by the Lower Range Value and Upper Range Value, for normal operating modes. The units of this variable are always in percent.
257	SP %
258	Sensor temperature- Temperature measured at sensor capsule.
259	Engineer Unit Select Code for Easy Setting
260	psia
261	mmHgA
262	mmAq
263	mmWG
264	Torr
265	inHgA
266	gf/cm2
267	kgf/cm2
268	kg/cm2G
269	kg/cm2A
270	t/h
271	m3/h
272	m3/min
273	l/h
274	l/min
275	kl/h
276	kl/min
277	Nl/h
278	Nl/min
279	Nm3/h
280	Nm3/min
281	ACFH
282	ACFM
283	SCFH
284	SCFM
285	GPH
286	GPM
287	kg/m3
288	g/cm3
289	Engineering display- Process variable displayed in user scale and unit.
290	Engr Disp
291	Engineering display exponents- Exponents for user scale display.
292	Engr exp
293	x1
294	x10
295	x100
296	x1000
297	Engineering unit- Engineering unit for user scale display.
298	Engr Unit
299	Lower pressure trim deviation- Deviation from the original value.
300	P LTD
301	Upper pressure trim deviation- Deviation from the original value.
302	P UTD
303	Lower static pressure trim point- Applied static pressure at which the last lower static pressure trim was performed.
304	SP LTP
305	Upper static pressure trim point- Applied static pressure at which the last upper static pressure trim was performed.
306	SP UTP
307	Lower static pressure trim deviation- Deviation from the original value.
308	SP LTD
309	Upper static pressure trim deviation- Deviation from the original value.
310	SP UTD
311	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record who to trim the device.
312	Trim Who
313	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record when the latest trim is done for the device.
314	Trim Date
315	Trim information- Text that is associated with the trim information. This text can be used by the user in any way. A recommended use is to record where the latest trim is done for the device.
316	Trim Loc
317	Trim information- Text that is associated with the trim information. This text can be used by the user in any way, and there is no recommended use.
318	Trim Desc
319	Low cut- Sets the range in vicinity of 0% within which the low cut function is activated according to the selected low cut mode.
320	Low cut
321	5.2f
322	Low cut mode- Selects the type of the low cut function to be used; LINEAR or ZERO.
323	Low cut mode
324	High/Low swap- Reverses the high pressure side and low pressure side of the transmitter. For example, use this function when assigning the high pressure impulse line connection to the L side of the transmitter.
325	H/L Swap
326	Static Pressure Lower Range Value- Defines the operational endpoint from which the 0% point of the Percent Range are derived.
327	SP LRV
328	Static Pressure Upper Range Value- Defines the operational endpoint from which the 100% point of the Percent Range are derived.
329	SP URV
330	Static Pressure Variable Unit- Engineering unit to be displayed with the Digital Value representation, Minimum Span, Upper Range Value, Lower Range Value, Lower Sensor Limit, and Upper Sensor Limit for the Static Pressure.
331	SP Unit
332	Absolute/gauge selection- Type of Static pressure variable.
333	A/G Select
334	Gauge
335	Absolute
336	Atmospheric Pressure Value- Sets the coefficient value used for the conversion of the measured absolute pressure value into gauge pressure value.
337	Atm. Pres Value
338	Static Pressure High/Low Select- Measuring point of the static pressure; high pressure side or low pressure side.
339	SP H/L Select
340	Amp Temperature
341	Amp temp
342	Field Device Variable Unit- Digital unit that the variable will be displayed with. Sensor Temperature- Temperature associated with the sensor that is responsible for a process measurement.
343	Temp Unit
344	Bi-directional flow measurement setup- Enables/disables bi-directional flow measurement mode. In this mode, when the pressure equivalent to 0% is applied, the device outputs 50%. Applicable only for differential pressure transmitters.
345	Bi-dir mode
346	Normal Mode
347	Bi-Direction Mode
348	Quick response- Enables/disables to set the damping value less than 0.5 sec.
349	Quick resp
350	Temperature Zero compensation mode- Enables/disables temperature zero compensation.
351	T.Z. Cmp mode
352	Temperature Zero shift compensation- Defines the value to be used for temperature zero shift compensation.
353	Temp Zero
354	%/degC
355	7.3f
356	Signal characterizer- Enables/disables signal characterizer function.
357	S.C.
358	Disabled
359	Enabled
360	Number of break points- Sets the number of points for signal characterizer.
361	Num of points
362	2u
363	Displays the start point of X.
364	X Start
365	Displays the start point of Y.
366	Y Start
367	Displays the end point of X.
368	X End
369	Displays the end point of Y.
370	Y End
371	Status of digital output- Displays the current status of digital output.
372	Digital Output
373	Automatic recover- Defines if the device automatically returns to normal operation without restarting or not, once after it recovers from the sensor error status.
374	Auto recover
375	Analog output lower limit- Sets the lower limit value for analog output.
376	AO lower limit
377	Analog output upper limit- Sets the upper limit value for analog output.
378	AO upper limit
379	Selects alert mode for pressure alarm.
380	Pres Alert mode
381	Hi. Al Detect
382	Lo. Al Detect
383	Hi/Lo. Al Detect
384	Sets threshold value for pressure high alarm.
385	Hi Alert Val
386	Sets threshold value for pressure low alarm.
387	Lo Alert Val
388	Selects alert mode for static pressure alarm.
389	SP Alert mode
390	Selects alert mode for sensor temperature alarm.
391	Temp Alert mode
392	Bar indicator- Defines to show/hide bar indicator on LCD.
393	Bar indicator
394	Sets threshold value for static pressure high alarm.
395	SP Hi Alert Val
396	Sets threshold value for static pressure low alarm.
397	SP Lo Alert Val
398	Sets threshold value for sensor temperature high alarm.
399	Temp Hi Alert Val
400	4.0f
401	Sets threshold value for sensor temperature low alarm.
402	Temp Lo Alert Val
403	DO selection- Select alarm(s) whose status should be output via digital output.
404	DO Select
405	Pres/SP
406	Pres/Temp
407	SP/Temp
408	Pres/SP/Temp
409	Diag Alarm
410	All
411	DO signal type- Defines the action of digital output when the alarm is detected.
412	DO Signal type
413	ON WHEN AL. DETECT
414	OFF WHEN AL. DETECT
415	LCD output1- Defines the variable to be shown on LCD.
416	Disp Out1
417	PRES
418	PRES %
419	ENGR. PRES
420	LCD output2- Defines the variable to be shown on LCD.
421	Disp Out2
422	LCD output3- Defines the variable to be shown on LCD.
423	Disp Out3
424	LCD output4- Defines the variable to be shown on LCD.
425	Disp Out4
426	Display pressure % function- Defines the display mode for pressure variable in %; Linear or Squareroot.
427	Disp Pres % fnctn
428	Display pressure % resolution- Defines the display resolution level for pressure variable in %; normal or high resolution.
429	Disp Pres % Reso
430	High Resolution
431	Pressure display decimal position- Defines the decimal point position for the pressure variable display.
432	Pres disp point
433	0
434	1
435	2
436	3
437	4
438	Static pressure display decimal point position- Defines the decimal point position for the static pressure variable display.
439	SP disp point
440	Engineering display lower range value- Sets the lower range value equivalent to 0% for user scale display.
441	Engr LRV
442	Engineering display upper range value- Sets the upper range value equivalent to 100% for user scale display.
443	Engr URV
444	Engineering display decimal position- Defines the decimal point position for user scale display.
445	Engr point
446	Model 1- Model and Suffix codes of the device.
447	Model 1
448	Model 2- Part of the Model and suffix codes of the device, which follows the codes shown in Model 1.
449	Model 2
450	Model 3- Part of the Model and suffix codes of the device, which follows the codes shown in Model 2.
451	Model 3
452	Style code- Displays the style code of the device.
453	Style No.
454	Serial number- Displays the serial number of the device.
455	Serial No.
456	Manufacturing date- Displays the date of manufacturing the device.
457	Mftr Date
458	Extra number- Reference number for special customization.
459	Extra No.
460	External zero-adjustment permission- Enables/disables external zero adjustment.
461	Ext SW
462	Software rev
463	Gasket Material- Construction material of a seal that exists between the module and flange.
464	Gasket matl
465	Process Connector Size- Hardware adjacent to the sensor, that physically connects the process to the sensor.
466	Process Conn size
467	ANSI3, C150
468	ANSI3, C300
469	ANSI3, C600
470	ANSI4, C150
471	ANSI4, C300
472	ANSI2, C150
473	ANSI2, C300
474	ANSI2, C600
475	DIN80, PN10/16
476	DIN80, PN25/40
477	DIN80, PN64
478	DIN100, PN10/16
479	DIN100, PN25/40
480	DIN50, PN10/16
481	DIN50, PN25/40
482	DIN50, PN64
483	ANSI 150
484	ANSI 300
485	ANSI 600
486	DIN 10/16
487	DIN 25
488	DIN 40
489	1/2NPT Female
490	1/4NPT Female
491	Rc 1/2 Female
492	1/2NPT Male
493	G 1/2 Male
494	M2O * 1.5 Male
495	R 1/2 Male
496	Remote Seal Fill Fluid- Fluid material in the device remote seal.
497	Silicone
498	SH704
499	SH705
500	Ethy Gly/H2O
501	Prop Gly/H2O
502	Software seal- Displays whether or not a master password was used (Break).
503	Software seal
504	Break
505	Keep
506	SI Option
507	OFF
508	ON
509	Pressure Sensor Range Code
510	P Range code
511	M
512	H
513	L
514	A
515	B
516	C
517	E
518	V
519	D
520	Static Pressure Sensor Range Code
521	SP Range code
522	Standard
523	Pressure Value or % Value for Trim
524	Pres for trim
525	Static Pressure Value or % Value for Trim
526	SP for trim
527	Engineer Unit of Capital Letter
528	Small Character of Engineer Unit
529	X1 Value
530	X1
531	Y1 Value
532	Y1
533	X2 Value
534	X2
535	Y2 Value
536	Y2
537	X3 Value
538	X3
539	Y3 Value
540	Y3
541	X4 Value
542	X4
543	Y4 Value
544	Y4
545	X5 Value
546	X5
547	Y5 Value
548	Y5
549	X6 Value
550	X6
551	Y6 Value
552	Y6
553	X7 Value
554	X7
555	Y7 Value
556	Y7
557	X8 Value
558	X8
559	Y8 Value
560	Y8
561	X9 Value
562	X9
563	Y9 Value
564	Y9
565	Pressure Trim Mode Selection Code
566	Auto, Lower Pt
567	Auto, Upper Pt
568	Manual, Lower Pt
569	Manual, Upper Pt
570	Pressure Trim Point or Deviation
571	Static Pressure Trim Mode Selection Code
572	Static Pressure Trim Point or Deviation
573	Trim Clear Code
574	Not Clear
575	ALL
576	Keyword for Test Mode
577	Data No. for Test
578	Data1 for Test
579	Data2 for Test
580	04X
581	08X
582	Error Record Selection Code
583	Log1
584	Latest
585	Log2
586	Log3
587	Log4
588	Oldest
589	Error Record 0
590	Error Rec 0
591	2X
592	Error Record 1
593	Error Rec 1
594	Error Record 2
595	Error Rec 2
596	Error Record 3
597	Error Rec 3
598	Error Record 4
599	Error Rec 4
600	Error Record 5
601	Error Rec 5
602	Error Record 6
603	Error Rec 6
604	Error Record 7
605	Error Rec 7
606	Data Selection Code
607	Value 1
608	VALUE 1
609	Value 2
610	VALUE 2
611	Digital Output Test Code
612	Exit DO Test mode
613	Space for 8 characters
614	Diag Error Status.
615	Diag Error
616	Bit mask for Alarm against Diag Error Status.
617	Diag Option
618	Diag Mode.
619	Diag Mode
620	Stop
621	Calculation
622	Reference
623	Diag Applicable.
624	Diag Applicable
625	Ratio of Root fluct DP for Reference with Compensation Status.
626	Ratio fDP Status
627	Sensor Failure
628	Device Failure
629	Uncertain
630	Invalid Ref
631	Good
632	Ratio of Root fluct DP for Reference.
633	Ratio fDP
634	Ratio of Root fluct SP low side for Reference Status.
635	Ratio fSPl Status
636	Ratio of Root fluct SP low side for Reference.
637	Ratio fSPl
638	Ratio of Root fluct SP high side for Reference Status.
639	Ratio fSPh Status
640	Ratio of Root fluct SP high side for Reference.
641	Ratio fSPh
642	Blocking Factor Status.
643	BlkF Status
644	Blocking Factor.
645	BlkF
646	DPAvg Status.
647	DPAvg Status
648	DPAvg.
649	DPAvg
650	Compensated Ratio of Root fluct DP for Reference Status.
651	CRatio fDP Status
652	Compensated Ratio of Root fluct DP for Reference.
653	CRatio fDP
654	Non-Compensated Ratio of Root fluct DP for Reference Status.
655	NRatio fDP Status
656	Non-Compensated Ratio of Root fluct DP for Reference.
657	NRatio fDP
658	fluct DP Status.
659	fDP Status
660	fluct DP.
661	fDP
662	12g
663	.5e
664	fluct SP low side Status.
665	fSPl Status
666	fluct SP low side.
667	fSPl
668	fluct SP high side Status.
669	fSPh Status
670	fluct SP high side.
671	fSPh
672	Test 1
673	Test 2
674	Test 3
675	Test 4
676	Diag Period.
677	Diag Period
678	Diag Limit fluct DP max.
679	Lim fDPmax
680	Diag Limit fluct DP min.
681	Lim fDPmin
682	Diag Limit fluct SP low side max.
683	Lim fSPlmax
684	Diag Limit fluct SP low side min.
685	Lim fSPlmin
686	Diag Limit fluct SP high side max.
687	Lim fSPhmax
688	Diag Limit fluct SP high side min.
689	Lim fSPhmin
690	Diag Limit Blocking Factor max.
691	Lim BlkFmax
692	Diag Limit Blocking Factor min.
693	Lim BlkFmin
694	Diag Limit DPAvg max.
695	Lim DPAvgmax
696	5.5f
697	Diag Limit DPAvg min.
698	Lim DPAvgmin
699	Diag Alarm Suppression Count.
700	Diag Supp Count
701	.0d
702	Diag Description.
703	Diag Description
704	Reference fluct DP Status.
705	Ref fDP Status
706	Reference fluct DP.
707	Ref fDP
708	10g
709	.3e
710	Reference fluct SP low side Status.
711	Ref fSPl Status
712	Reference fluct SP low side.
713	Ref fSPl
714	Reference fluct SP high side Status.
715	Ref fSPh Status
716	Reference fluct SP high side.
717	Ref fSPh
718	Reference Blocking Factor Status.
719	Ref BlkF Status
720	Reference Blocking Factor.
721	Ref BlkF
722	10.6f
723	Reference DPAvg Status.
724	Ref DPAvg Status
725	Reference DPAvg.
726	Ref DPAvg
727	Reference Limit fluct DP min.
728	Ref Lim fDPmin
729	Reference Limit fluct SP min.
730	Ref Lim fSPmin
731	Reference Limit Blocking Factor max.
732	Ref Lim BlkFmax
733	Flow Compensation for Ratio of Root fluct DP.
734	Diag DPComp
735	Compensation
736	Non-Compensation
737	Flg temp.
738	Flg temp
739	Flg Temp Coef.
740	Flg Temp Coef
741	Flg Temp Hi Alert Val.
742	Flg Temp Hi Alert Val
743	Flg Temp Lo Alert Val.
744	Flg Temp Lo Alert Val
745	Diag Analog Output Option.
746	Diag Out Option
747	Burnout
748	Fall back
749	Diag Fixed Analog Output Value.
750	Diag Fixed Out Val
751	Small Char. did not convert successfully.
752	Analog output trim
753	SP setup
754	Config SP Alerts
755	Additional Info
756	Write variables
757	Device Variables and Status
758	Properties
759	Burst Condition
760	Burst Message 1
761	Burst Message 2
762	Burst Message 3
763	Burst Variables
764	Event Notification
765	Event Mask
766	Knowledge
767	Re-range
768	Time Stamp
769	Maintenance
770	Offline
771	Master Reset- Commands the EJX electronics to reset and perform a selftest. Reports any errors that occured.
772	Reset Configuration changed flag.
773	Reset Cfg chng flag
774	Simulate.
775	Simulate
776	Set Burst Period
777	Configure Burst Period
778	Set Burst Trigger
779	Configure Burst Trigger
780	Set Event Notification Timing
781	Configure Event Notification Timing
782	Acknowledge Event Notification
783	Static Pressure Lower Sensor Limit Value- Defines the minimum usable value for the Lower Range Value for the static pressure.
784	SP LSL
785	Static Pressure Upper Sensor Limit Value- Defines the maximum usable value for the Upper Range Value for the static pressure.
786	SP USL
787	Static Pressure Minimum Span- Defines the minimum usable span for the static pressure.
788	SP Min span
789	Static Pressure Damping Value- Damping time constant applied to both the Digital Value representation for static pressure. The units of this variable are always in seconds.
790	SP Damp
791	Sensor Temperature - Temperature at the sensor that is responsible for a process measurement.
792	temperature_digital_units_help
793	temperature_digital_value_help
794	Static Pres
795	static_pressure_digital_units_help
796	static_pressure_digital_value_help
797	Percent Range
798	percent_range_digital_units_help
799	percent_range_digital_value_help
800	Loop Warning Variables
801	Displays a warning message before new values are sent.
802	Percent Range Variable Unit
803	Percent Range Data Quality
804	Percent Range Quality help
805	Percent Range Limit Status
806	Percent Range Limit Status help
807	Percent Range Classification
808	Percent Range Classification help
809	Percent Range Family status
810	Percent Range Family status help
811	Percent Range Family
812	Percent Range Family help
813	Percent Range Update time
814	Percent Range Update time period help
815	0 ms
816	45 ms
817	360 ms
818	1 s
819	Percent Range USL
820	Percent RangeUSL help
821	Percent Range LSL
822	Percent Range LSL help
823	Percent Range min span
824	Percent Range min span help
825	Percent Range Damp
826	Percent Range Damp help
827	8.3f
828	Percent Range snsr s/n
829	Percent Ranges nsr s/n help
830	7d
831	% rnge property
832	Variable is not calculated by device
833	Device variable is not calculated by field device
834	Variable is being simulated
835	Device variable is being simulated
836	Loop Current Variable Unit
837	Loop Current Data Quality
838	Loop Current Data Quality help
839	Loop Current Limit Status
840	Loop Current Limit Status help
841	Loop Current Classification
842	Loop Current Classification help
843	Loop Current Family status
844	Loop Current Family status help
845	Loop Current Family
846	Loop Current Family help
847	Loop Current Update time
848	Loop Current Update time period help
849	Loop Current USL
850	Loop Current USL help
851	Loop Current LSL
852	Loop Current LSL help
853	Loop Current min span
854	Loop Current min span help
855	Loop Current Damp
856	Loop Current Damp help
857	Loop Current snsr s/n
858	Loop Current snsr s/n help
859	Loop Current property
860	loop_current_digital_units_help
861	loop_current_digital_value_help
862	Pres Classification
863	Pressure Classification help
864	Pres Data Quality
865	Pressure Quality help
866	Pres Limit Status
867	Pressure Limit Status help
868	Pres Family status
869	Pressure Family status help
870	Pres Family
871	Pressure Family help
872	Pres property
873	Activation Key for Optional Function.
874	Option Password
875	Event Number
876	Temp Data Quality
877	Temperature Data Quality help
878	Temp Limit Status
879	Temperature Limit Status help
880	Temp Classification
881	Temperature Classification help
882	Temp family status
883	Temperature family status help
884	Temp Family
885	Temperature Family help
886	Temp update time
887	Temperature Update time period help
888	Temp USL
889	Temp LSL
890	Temp min span
891	Temp snsr s/n
892	Snsr temp property
893	SP Data Quality
894	Static Pressure Quality help
895	SP Limit Status
896	Static Pressure Limit Status help
897	SP Classification
898	Static Pressure Classification help
899	SP Family status
900	Static Pressure Family status help
901	SP Family
902	Static Pressure Family help
903	SP update time
904	Static Pressure Update time period help
905	SP snsr s/n
906	SP snsr s/n help
907	Pressure write dev var code
908	SP write dev var code
909	SP property
910	temperature write dev var code
911	% range write dev var code
912	Loop current write dev var code
913	Test Auto Release Time
914	10 min
915	30 min
916	60 min
917	3 hour
918	6 hour
919	12 hour
920	PV Analog Channel Saturated
921	PV Analog Channel Fixed
922	Wireless
923	WirelessHART Device
924	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
925	Primary
926	Primary Analog Channel
927	Secondary
928	Secondary Analog Channel
929	Tertiary
930	Tertiary Analog Channel
931	Quaternary
932	Quaternary Analog Channel
933	Quinary
934	Quinary Analog Channel
935	Critical Power Failure
936	Lock all
937	Trim not supported
938	Configuration cannot be changed
939	Locked by gateway
940	Analog Input Channel
941	Analog Output Channel
942	Secondary Analog Channel Saturated
943	Tertiary Analog Channel Saturated
944	Quaternary Analog Channel Saturated
945	Quinary Analog Channel Saturated
946	Secondary Analog Channel Fixed
947	Tertiary Analog Channel Fixed
948	Quaternary Analog Channel Fixed
949	Quinary Analog Channel Fixed
950	Simulation active
951	The device is in simulation mode and the level output is not representative of the process.
952	Non-Volatile memory failure
953	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
954	Volatile memory error
955	The RAM memory check is invalid or maybe corrupt
956	Watchdog reset executed
957	A watchdog reset has been performed
958	Voltage conditions out of range
959	A voltage condition is outside its allowable range
960	Environmental conditions out of range
961	An internal or environmental condition is beyond acceptable limits.
962	Electronic failure
963	A hardware problem not related to the sensor has been detected.
964	Subdevice list changed
965	Duplicate master detected
966	Capacity Denied
967	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
968	Bandwidth allocation pending
969	Block transfer pending
970	Battery life
971	Percent range
972	Loop current
973	Primary variable
974	Secondary variable
975	Tertiary variable
976	Quaternary variable
977	Read receive time
978	Write date and time
979	Non-Volatile Clock
980	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
981	Clock Uninitialized
982	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
983	None
984	No restrictions
985	SI Only
986	Restricted to SI Unit codes only
987	Process automation device
988	Discrete device
989	Hybrid:Process automation+discrete
990	I/O System
991	WirelessHART Process automation device
992	WirelessHART Discrete device
993	WirelessHART Process automation+discrete
994	WirelessHART Gateway
995	WirelessHART Access point
996	WirelessHART Process adapter
997	WirelessHART Discrete adapter
998	WirelessHART enabled handheld/portable maintenance tool
999	Device Profile
1000	US
1001	United States of America
1002	JP
1003	Japan
1004	DE
1005	Germany
1006	FR
1007	France
1008	ES
1009	Spain
1010	RU
1011	Russian Federation
1012	CN
1013	People's Republic of China
1014	Secondary Master
1015	Primary Master
1016	Device Diagnostic Status 0
1017	Device Diagnostic Status 1
1018	I/O and Subdevice Status
1019	WirelessHART Status
1020	Time Set Option
1021	Real Time Clock Flags
1022	Country
1023	Country of intended device installation
1024	SI Unit Control
1025	Indicates if device should only display SI unit codes
1026	Enable on token-passing data link layer only
1027	Enable on TDMA data link layer only
1028	Enable on both TDMA and token-passing data link layer
1029	Continuous
1030	The Burst Message is published continuously at (worst case) the Minimum Update Period.
1031	Window
1032	The Burst Message is triggered when the source value deviates more than the specified trigger value
1033	Rising
1034	The Burst Message is triggered when source value Rises Above the specified trigger value.
1035	Falling
1036	The Burst Message is triggered when the source value Falls Below the specified trigger value.
1037	On-change
1038	The Burst Message is triggered when any value in the message changes.
1039	Enable event notification on token-passing data link layer
1040	Enable event notification on TDMA data link layer
1041	Enable event notification on TDMA and token-passing data link layer
1042	Configuration changed event pending
1043	Device status event pending
1044	More status available event pending
1045	Wired HART Enabled
1046	Enabled on Wired HART device connection only
1047	Wireless HART Enabled
1048	Enabled on WirelessHART device connection only
1049	Both Wired and WirelessHart Enabled
1050	Enabled on both Wired and WirelessHART connections
1051	Burst Msg Trigger Mode
1052	Device Diagnostic Status 2 Mask
1053	Device Diagnostic Status 3 Mask
1054	Latched Device Status
1055	Operate mode Mask
1056	Not Defined
1057	Latched Ext dev status
1058	Latched Device Diagnostic Status 0
1059	Latched Device Diagnostic Status 1
1060	Latched Device Diagnostic Status 2
1061	Latched Device Diagnostic Status 3
1062	Latched AO saturated
1063	Latched AO fixed
1064	Latched Operate Mode
1065	Relative time value on network
1066	8u
1067	Dynamic Variables Returned for Device Variables
1068	Command Response Truncated
1069	Configuration Change Counter Mismatch
1070	Status bytes mismatch
1071	Device Variable
1072	Burst Command
1073	Subdevice Missing
1074	Total Burst Msgs
1075	Total number of burst messages supported by this device
1076	Current Date
1077	Current Date based upon the real-time clock in the field device
1078	Current Time
1079	Current Time based upon the real-time clock in the field device
1080	Set Clock Date
1081	Date to set the real-time clock in the field device to, or date that the real-time clock was last set
1082	Set Clock Time
1083	Time to set the real time clock in the field device to, or time that the real-time clock was last set
1084	Burst Variable Slot - Device variable code assigned to the slot to be read in burst mode.
1085	Burst Variable Codes
1086	The time when the first unacknowledged event was triggered
1087	5.3f
1088	Burst Message Number
1089	Number of Events Supported
1090	Latched Cfg chng count
1091	Device Specific Status 0 Mask
1092	Device Specific Status 14 Mask
1093	Device Specific Status 15 Mask
1094	Device Specific Status 16 Mask
1095	Device Specific Status 17 Mask
1096	Device Specific Status 18 Mask
1097	Device Specific Status 19 Mask
1098	Device Specific Status 20 Mask
1099	Device Specific Status 21 Mask
1100	Device Specific Status 22 Mask
1101	Device Specific Status 23 Mask
1102	Device Specific Status 24 Mask
1103	Latched Device Specific Status 0
1104	Latched Device Specific Status 1
1105	Latched Device Specific Status 2
1106	Latched Device Specific Status 3
1107	Latched Device Specific Status 4
1108	Latched Device Specific Status 5
1109	Latched Device Specific Status 14
1110	Latched Device Specific Status 15
1111	Latched Device Specific Status 16
1112	Latched Device Specific Status 17
1113	Latched Device Specific Status 18
1114	Latched Device Specific Status 19
1115	Latched Device Specific Status 20
1116	Latched Device Specific Status 21
1117	Latched Device Specific Status 22
1118	Latched Device Specific Status 23
1119	Latched Device Specific Status 24
1120	Update time adjusted
1121	Invalid burst message
1122	Invalid device variable classification
1123	Invalid burst trigger mode selection code
1124	Burst condition conflict
1125	Update period increased
1126	Insufficient bandwidth
1127	Update period or debounce interval adjusted
1128	Update times adjusted
1129	Update rate uncertain
1130	Not all events cleared
1131	count
1132	.3g
1133	.f
1134	%
1135	3.2f
1136	s
1137	4.2f
1138	6.4f
1139	This function is not supported.
1140	In write protect mode.
1141	Current power on informatin is ON. Select status
1142	OFF;ON
1143	Current power on informatin is OFF. Select status
1144	Power on info is changed to ON.
1145	Power on info is changed to OFF.
1146	Current power on informatin is ON.
1147	Current power on informatin is OFF.
1148	Confirm that the configuration tool supports new universal rev. After the universal rev is changed, the following operations are required. 1 Exit the configuration tool. 2 Power OFF and ON the device. 3 Restart the configuration tool.
1149	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. New universal rev is %{next_universal_rev} with fld dev rev %{next_device_rev}. Are you sure to change the universal rev?
1150	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. Are you sure to change the universal rev?
1151	Universal rev %{test_key_4_upper1} is not supported!
1152	Enter new rev number. 5: universal rev 5 7: universal rev 7
1153	Number is invalid.
1154	Current universal rev is %{0}. Universal rev is not changed.
1155	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. Are you sure to stay with current universal rev?
1156	New rev is applied only after power OFF and ON the device. Are you sure to change the universal rev from %{universal_revision} to %{object_universal_rev}?
1157	Setting in progress, please wait for several seconds.
1158	Process incompleted.
1159	To complete the change of universal rev: 1 Exit the configuration tool. 2 Power OFF and ON the device. 3 Restart the configuration tool.
1160	Process completed.
1161	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}. New universal rev will be %{next_universal_rev} with fld dev rev %{next_device_rev}.
1162	Current universal rev is %{universal_revision} with fld dev rev %{transmitter_revision}.
1163	Self test in progress please wait
1164	Device maybe stuck in selftest.
1165	Device maybe stuck in master reset.
1166	Master Reset OK
1167	D/A trim data is cleared.
1168	Select trim mode
1169	Off;Auto, Lower Pt;Auto, Upper Pt;Manual, Lower Pt;Manual, Upper Pt
1170	Pres for trim %{0} %{1}
1171	tmp
1172	Pres sensor trim data is cleared.
1173	SP for trim %{0} %{1}
1174	SP sensor trim data is cleared.
1175	Execute OK ?
1176	Exit;Execute
1177	Performing log clear
1178	0%;100%;Exit
1179	Apply new 0% input
1180	Current applied process value: %{static_pressure_value} %{static_pressure_units}
1181	Set as 0% value;Read new value;Leave as found
1182	Apply new 100% input
1183	Set as 100% value;Read new value;Leave as found
1184	Select one
1185	List;Edit all points;Edit one point;Exit
1186	List X1 %[6.2f]{0}% Y1 %[6.2f]{1}% X2 %[6.2f]{2}% Y2 %[6.2f]{3}% X3 %[6.2f]{4}% Y3 %[6.2f]{5}%
1187	List X4 %[6.2f]{6}% Y4 %[6.2f]{7}% X5 %[6.2f]{8}% Y5 %[6.2f]{9}% X6 %[6.2f]{10}% Y6 %[6.2f]{11}%
1188	List X7 %[6.2f]{12}% Y7 %[6.2f]{13}% X8 %[6.2f]{14}% Y8 %[6.2f]{15}% X9 %[6.2f]{16}% Y9 %[6.2f]{17}%
1189	Num of points is 0.
1190	It will set S.C. to be disabled, OK?
1191	No;Yes
1192	Set S.C. to be disabled...
1193	Specify S.C. point to set value
1194	choice
1195	Off;On;Exit
1196	Digital Output is fixed to %{0}
1197	Enter Engr Unit:
1198	Enter a space for the character to display it in lowercase:
1199	Select case:
1200	Write;Read;Coefs Clear;End
1201	Test Key 1
1202	Test Key 2
1203	Select one:
1204	Test Key 3;Test Key 4
1205	Test Key 3
1206	Test Key 4
1207	Test Key 3 %{0}
1208	Test Key 4 %{0}%{1} %{2}
1209	Now Clearing!
1210	Enter current password to enable to write for 10 minutes:
1211	Released the write protection for 10 minutes.
1212	If you wish to release completely, you have to change password to all of spaces.
1213	Enter new password to change state of write protect:
1214	Re-enter new password within 30 seconds:
1215	Aborting method due to last error
1216	Changed to new password.
1217	It changed the state of protection related password.
1218	Current Diag Mode is : %{diag_mode} Select Diag Mode
1219	Stop;Calculation;Reference
1220	Show the:
1221	Log1(Latest);Log2;Log3;Log4(Oldest);Exit
1222	Advanced Diag Fail.
1223	Simulation mode
1224	No error
1225	Select unit
1226	;kPa;MPa;mbar;bar;psi;psia;mmH2O;mmHg;mmHgA;mmAq;mmWG;Torr;inH2O;inHg;inHgA;ftH2O;gf/cm2;kgf/cm2;kg/cm2G;kg/cm2A;atm;kg/h;t/h;m3/h;m3/min;l/h;l/min;kl/h;kl/min;Nl/h;Nl/min;Nm3/h;Nm3/min;ACFH;ACFM;SCFH;SCFM;GPH;GPM;m;mm;in;ft;kg/m3;g/cm3
1227	;kPa;MPa;mbar;bar;atm;kg/h;t/h;m3/h;m3/min;l/h;l/min;kl/h;kl/min;Nl/h;Nl/min;Nm3/h;Nm3/min;m;mm;kg/m3;g/cm3
1228	It will reset the master CPU, OK ?
1229	Master Reset in progress please wait
1230	Self Test OK
1231	Configuration changed flag was reset.
1232	Select Device variable.
1233	Off;PV;SV;TV;Percent Range;Loop Current
1234	Input Digital value.(%{ejx_lvar_sim_unit_code})
1235	Select Data quality.
1236	Bad;Poor accuracy;Manual / Fixed;Good
1237	Select Limit status.
1238	Not limited;Low limited;High limited;Constant
1239	Choose update period
1240	0.5s;1s;2s;4s;8s;16s;32s;1min;5min;10min;15min;30min;45min;60min
1241	Choose max update period
1242	Error - Update period is larger than max update period. Please select update period again.
1243	Choose burst trigger mode.
1244	Continuous;On-change
1245	Continuous;Window;Rising;Falling;On-change
1246	Set Burst Trigger Level for
1247	[ %{burst_messages[0].BURST_UNIT} ]
1248	tmp_burst_trigger_level
1249	[ %{burst_messages[1].BURST_UNIT} ]
1250	[ %{burst_messages[2].BURST_UNIT} ]
1251	select update period
1252	select max update period
1253	Choose event debounce interval
1254	Off;0.5s;1s;2s;4s;8s;16s;32s;1min;5min;10min;15min;30min;45min;60min
1255	Current applied process value: %{pressure_value} %{pressure_units}
1256	low
1257	high
1258	Enter Event Number
1259	Select Transaction
1260	Trans 0: Read Event Notification;Trans 1: Send Acknowledge
Reference ID	String