| 0 |
Failure |
| 1 |
Out of Specification |
| 2 |
Function Check |
| 3 |
Device Configuration Locked |
| 4 |
Status Simulation Active |
| 5 |
Discrete Variable Simulation Active |
| 6 |
Event Notification Overflow |
| 7 |
Battery or Power Supply needs Maintenance |
| 8 |
Subdevice Mismatch |
| 9 |
Subdevice with Duplicate IDs Found |
| 10 |
Stale Data Notice |
| 11 |
Radio failure |
| 12 |
Yokogawa |
| 13 |
AXG1A |
| 14 |
10:Main board CPU failure |
| 15 |
11:Reverse calculation failure |
| 16 |
12:Main board EEPROM failure |
| 17 |
13:Main board EEPROM default |
| 18 |
14:Sensor board failure |
| 19 |
15:Sensor communication error |
| 20 |
16:A/D1 failure[Signal] |
| 21 |
17:A/D2 failure[Exciter] |
| 22 |
18:Coil open |
| 23 |
19:Coil short |
| 24 |
20:Exciter failure |
| 25 |
21:PWM1 stop |
| 26 |
22:PWM2 stop |
| 27 |
23:Option board mismatch |
| 28 |
24:Option board EEPROM failure |
| 29 |
25:Option board A/D failure |
| 30 |
26:Option board SPI failure |
| 31 |
27:Parameter restore incomplete |
| 32 |
28:Indicator board failure |
| 33 |
29:Indicator board EEPROM failure |
| 34 |
30:LCD driver failure |
| 35 |
31:Indicator board mismatch |
| 36 |
32:Indicator communication error |
| 37 |
33:microSD card failure |
| 38 |
50:Signal overflow |
| 39 |
51:Empty pipe detection |
| 40 |
52:H/L or HH/LL alarm |
| 41 |
53:Adhesion over level 4 |
| 42 |
60:Span configuration error |
| 43 |
61:PV flow select configuration error |
| 44 |
62:Analog output 1 4-20mA limit error |
| 45 |
63:Analog output 2 4-20mA limit error |
| 46 |
64:Analog output 1 multi range error |
| 47 |
65:H/L HH/LL configuration error |
| 48 |
66:Density configuration error |
| 49 |
67:Pulse output 1 configuration error |
| 50 |
68:Pulse output 2 configuration error |
| 51 |
69:Nominal size configuration error |
| 52 |
70:Adhesion configuration error |
| 53 |
71:Flow noise configuration error |
| 54 |
72:Data logging not started |
| 55 |
80:Analog output 1 saturated |
| 56 |
81:Analog output 2 saturated |
| 57 |
82:Pulse output 1 saturated |
| 58 |
83:Pulse output 2 saturated |
| 59 |
84:Analog input saturated |
| 60 |
85:Cable misconnect |
| 61 |
86:Coil insulation warning |
| 62 |
131:Transmitter type mismatch |
| 63 |
87:Adhesion over level 3 |
| 64 |
88:Low conductivity warning |
| 65 |
89:Insulation detection |
| 66 |
90:Flow noise over level 3 |
| 67 |
91:Flow noise over level 4 |
| 68 |
92:Autozero warning |
| 69 |
93:Verification warning |
| 70 |
94:Factory noise warning |
| 71 |
95:Simulation active |
| 72 |
96:Analog output 1 fixed |
| 73 |
97:Analog output 2 fixed |
| 74 |
98:Pulse output 1 fixed |
| 75 |
99:Pulse output 2 fixed |
| 76 |
100:Analog input fixed |
| 77 |
101:Parameter restore running |
| 78 |
102:Display over warning |
| 79 |
103:microSD card size warning |
| 80 |
104:Parameter backup incomplete |
| 81 |
105:microSD card mismatch |
| 82 |
106:microSD card removal procedure error |
| 83 |
120:Watchdog |
| 84 |
121:Power off |
| 85 |
122:Instant power failure |
| 86 |
123:Parameter backup running |
| 87 |
124:Data logging running |
| 88 |
130:Device ID not entered |
| 89 |
Velocity |
| 90 |
Volume flow |
| 91 |
Mass flow |
| 92 |
Totalizer1 |
| 93 |
Totalizer2 |
| 94 |
Totalizer3 |
| 95 |
Noise level |
| 96 |
Calorific value |
| 97 |
Help message for mass flow |
| 98 |
Data quality |
| 99 |
Limit status |
| 100 |
Simulate |
| 101 |
|
| 102 |
update period |
| 103 |
Update time period help |
| 104 |
Calorific value help |
| 105 |
Velocity help |
| 106 |
Totalizer1 help |
| 107 |
Totalizer2 help |
| 108 |
Totalizer3 help |
| 109 |
Flow noise |
| 110 |
Noise level help |
| 111 |
Mass Flow |
| 112 |
7g |
| 113 |
Mass flow digital unit |
| 114 |
Mass flow data quality |
| 115 |
Mass flow limit status |
| 116 |
Mass flow family status |
| 117 |
Mass flow rate classification |
| 118 |
Mass flow update period |
| 119 |
10 ms |
| 120 |
Flow family |
| 121 |
Mass flow USL |
| 122 |
Mass flow LSL |
| 123 |
Mass flow min span |
| 124 |
Mass flow damping value |
| 125 |
Flow rate write dev var code |
| 126 |
7d |
| 127 |
Mass flow URV |
| 128 |
Mass flow LRV |
| 129 |
Volume Flow |
| 130 |
Volume flow digital unit |
| 131 |
L/d |
| 132 |
Mgal/d |
| 133 |
Volume flow data quality |
| 134 |
Volume flow limit status |
| 135 |
Volume flow family status |
| 136 |
Volume flow rate classification |
| 137 |
Volume flow update period |
| 138 |
Volume flow family |
| 139 |
Volume flow rate write dev var code |
| 140 |
Volume flow USL |
| 141 |
Volume flow LSL |
| 142 |
Volume flow min span |
| 143 |
Volume flow damping value |
| 144 |
Volume flow URV |
| 145 |
Volume flow LRV |
| 146 |
Calorific unit |
| 147 |
MJ/s |
| 148 |
MJ/d |
| 149 |
Calorific data quality |
| 150 |
Calorific limit status |
| 151 |
Calorific val family status |
| 152 |
Calorific val rate classification |
| 153 |
Calorific val update period |
| 154 |
Not calculated |
| 155 |
Calorific val flow family |
| 156 |
Calorific val rate write dev var code |
| 157 |
Calorific value USL |
| 158 |
Calorific value LSL |
| 159 |
Calorific value min span |
| 160 |
Calorific damping |
| 161 |
Velocity digital unit |
| 162 |
Velocity data quality |
| 163 |
Velocity limit status |
| 164 |
Velocity family status |
| 165 |
Velocity rate classification |
| 166 |
Velocity update period |
| 167 |
Velocity family |
| 168 |
Velocity rate write dev var code |
| 169 |
Velocity USL |
| 170 |
Velocity LSL |
| 171 |
Velocity min span |
| 172 |
Velocity damping value |
| 173 |
Total 1 digital unit |
| 174 |
J |
| 175 |
Totalizer1 data quality |
| 176 |
Totalizer1 limit status |
| 177 |
Totalizer1 family status |
| 178 |
Totalizer1 rate classification |
| 179 |
Totalizer1 update period |
| 180 |
Totalizer1 family |
| 181 |
Totalizer1 rate write dev var code |
| 182 |
Total 2 digital unit |
| 183 |
Totalizer2 data quality |
| 184 |
Totalizer2 limit status |
| 185 |
Totalizer2 family status |
| 186 |
Totalizer2 rate classification |
| 187 |
Totalizer2 update period |
| 188 |
Totalizer2 family |
| 189 |
Totalizer2 rate write dev var code |
| 190 |
Total 3 digital unit |
| 191 |
Totalizer3 data quality |
| 192 |
Totalizer3 limit status |
| 193 |
Totalizer3 family status |
| 194 |
Totalizer3 rate classification |
| 195 |
Totalizer3 update period |
| 196 |
Totalizer3 family |
| 197 |
Totalizer3 rate write dev var code |
| 198 |
Totalizer1 USL |
| 199 |
Totalizer1 LSL |
| 200 |
Totalizer1 min span |
| 201 |
Totalizer1 damping val |
| 202 |
Totalizer2 USL |
| 203 |
Totalizer2 LSL |
| 204 |
Totalizer2 min span |
| 205 |
Totalizer2 damping val |
| 206 |
Totalizer3 USL |
| 207 |
Totalizer3 LSL |
| 208 |
Totalizer3 min span |
| 209 |
Totalizer3 damping val |
| 210 |
Flow noise unit |
| 211 |
Flow noise data quality |
| 212 |
Flow noise limit status |
| 213 |
Flow noise family status |
| 214 |
Flow noise classification |
| 215 |
Flow noise update period |
| 216 |
Flow noise family |
| 217 |
Flow noise USL |
| 218 |
Flow noise LSL |
| 219 |
Flow noise min span |
| 220 |
Flow noise damping for AO and frequency |
| 221 |
Flow noise write dev var code |
| 222 |
Flow noise URV |
| 223 |
Flow noise LRV |
| 224 |
slot0 |
| 225 |
slot1 |
| 226 |
slot2 |
| 227 |
slot3 |
| 228 |
slot4 |
| 229 |
slot5 |
| 230 |
slot6 |
| 231 |
slot7 |
| 232 |
Command |
| 233 |
Update Period |
| 234 |
Max Update Period |
| 235 |
Mode |
| 236 |
Trigger Mode |
| 237 |
Classification |
| 238 |
Trigger Units |
| 239 |
Trigger Level |
| 240 |
Burst Messages |
| 241 |
Events |
| 242 |
Invalid Date Detected |
| 243 |
Status |
| 244 |
Event Time Stamp |
| 245 |
Retry Time |
| 246 |
Update Time |
| 247 |
Debounce |
| 248 |
Flow Noise |
| 249 |
Density value select |
| 250 |
Fixed value |
| 251 |
Correction value |
| 252 |
Flow noise function |
| 253 |
Disable |
| 254 |
Enable |
| 255 |
Flow noise level 1 |
| 256 |
cm/s |
| 257 |
4.1f |
| 258 |
Flow noise level 2 |
| 259 |
Flow noise level 3 |
| 260 |
Flow noise level 4 |
| 261 |
Flow noise status |
| 262 |
Level0 |
| 263 |
Level1 |
| 264 |
Level2 |
| 265 |
Level3 |
| 266 |
Level4 |
| 267 |
Flow noise damping |
| 268 |
s |
| 269 |
Flow noise span |
| 270 |
Low conductivity function |
| 271 |
Conductivity value |
| 272 |
mS/cm |
| 273 |
Conductivity low limit |
| 274 |
6.4f |
| 275 |
Diagnostic execution |
| 276 |
Not execute |
| 277 |
Electorode insulation execute |
| 278 |
Connection check execute |
| 279 |
V peak hold value |
| 280 |
V |
| 281 |
4.3f |
| 282 |
Display select1 |
| 283 |
Flow rate(%) |
| 284 |
PV |
| 285 |
Flow rate(%bar) |
| 286 |
Calorie |
| 287 |
Tag number |
| 288 |
Long tag |
| 289 |
Commun Protocol |
| 290 |
Adhesion |
| 291 |
Analog out1 |
| 292 |
Analog out2 |
| 293 |
Flow noise level |
| 294 |
Totalizer1 count |
| 295 |
Totalizer2 count |
| 296 |
Totalizer3 count |
| 297 |
Display select2 |
| 298 |
None |
| 299 |
Display select3 |
| 300 |
Display select4 |
| 301 |
Display select5 |
| 302 |
Display select6 |
| 303 |
Display select7 |
| 304 |
Display select8 |
| 305 |
Log1 select |
| 306 |
Electrode A |
| 307 |
Electrode B |
| 308 |
V peak |
| 309 |
Log2 select |
| 310 |
Log3 select |
| 311 |
Log4 select |
| 312 |
PV flow select |
| 313 |
Volume |
| 314 |
Mass |
| 315 |
Diag |
| 316 |
Status output1 function |
| 317 |
No function |
| 318 |
Alarm output |
| 319 |
Warning output |
| 320 |
Total limit 1 |
| 321 |
Total limit 2 |
| 322 |
Total limit 3 |
| 323 |
H/L alarm |
| 324 |
HH/LL alarm |
| 325 |
Fwd/Rev range |
| 326 |
Auto2 range |
| 327 |
Ext2 answer |
| 328 |
Pulse2 select |
| 329 |
Non-Connect |
| 330 |
Status output2 function |
| 331 |
System alarm |
| 332 |
Process alarm |
| 333 |
Setting alarm |
| 334 |
50:Sig overflow |
| 335 |
51:Empty detect |
| 336 |
53:Adh over lv4 |
| 337 |
85:Cable miscon |
| 338 |
86:Coil insulate |
| 339 |
87:Adh over lv3 |
| 340 |
88:LC warn |
| 341 |
89:Insu detect |
| 342 |
90:FLN over lv3 |
| 343 |
91:FLN over lv4 |
| 344 |
93:Verif warn |
| 345 |
94:FC noise warn |
| 346 |
Lo alarm |
| 347 |
Lo Lo alarm |
| 348 |
Hi alarm |
| 349 |
Hi Hi alarm |
| 350 |
Status output3 function |
| 351 |
AO2 select |
| 352 |
Non-connect |
| 353 |
dev var sim data quality |
| 354 |
dev var sim limit status |
| 355 |
dev var sim unit |
| 356 |
simulation value for edit |
| 357 |
simulation flag for edit |
| 358 |
Status simulation mode |
| 359 |
Index of bit to be simulated |
| 360 |
3d |
| 361 |
Operate mode |
| 362 |
Device status Simulate |
| 363 |
Status group 0 Simulate |
| 364 |
Status group 1 Simulate |
| 365 |
Status group 2 Simulate |
| 366 |
Status group 3 Simulate |
| 367 |
Status group 4 Simulate |
| 368 |
Status group 5 Simulate |
| 369 |
Ext dev status Simulate |
| 370 |
Operate mode Simulate |
| 371 |
Device Diagnostic Status 0 Simulate |
| 372 |
Device Diagnostic Status 1 Simulate |
| 373 |
AO saturated Simulate |
| 374 |
I/O and Subdevice Status Simulate |
| 375 |
WirelessHART Status Simulate |
| 376 |
AO fixed Simulate |
| 377 |
Status group 14 Simulate |
| 378 |
Status group 15 Simulate |
| 379 |
Status group 16 Simulate |
| 380 |
Status group 17 Simulate |
| 381 |
Status group 18 Simulate |
| 382 |
Status group 19 Simulate |
| 383 |
Status group 20 Simulate |
| 384 |
last clock date for edit |
| 385 |
last clock time for edit |
| 386 |
Squawk |
| 387 |
Off |
| 388 |
On |
| 389 |
Squawk Once |
| 390 |
Flow user unit AO1 local |
| 391 |
User unit1 |
| 392 |
Flow user unit AO2 local |
| 393 |
User unit2 |
| 394 |
flow noise unit |
| 395 |
Volume flow unit |
| 396 |
Ml/s |
| 397 |
Ml/min |
| 398 |
Ml/h |
| 399 |
Ml/d |
| 400 |
m3/s |
| 401 |
m3/min |
| 402 |
m3/h |
| 403 |
m3/d |
| 404 |
kl/s |
| 405 |
kl/min |
| 406 |
kl/h |
| 407 |
kl/d |
| 408 |
l/s |
| 409 |
l/min |
| 410 |
l/h |
| 411 |
l/d |
| 412 |
cm3/s |
| 413 |
cm3/min |
| 414 |
cm3/h |
| 415 |
cm3/d |
| 416 |
kcf/s |
| 417 |
kcf/min |
| 418 |
kcf/h |
| 419 |
kcf/d |
| 420 |
cf/s |
| 421 |
cf/min |
| 422 |
cf/h |
| 423 |
cf/d |
| 424 |
mcf/s |
| 425 |
mcf/min |
| 426 |
mcf/h |
| 427 |
mcf/d |
| 428 |
Mgal/s |
| 429 |
Mgal/min |
| 430 |
Mgal/h |
| 431 |
kgal/s |
| 432 |
kgal/min |
| 433 |
kgal/h |
| 434 |
kgal/d |
| 435 |
gal/s |
| 436 |
gal/min |
| 437 |
gal/h |
| 438 |
gal/d |
| 439 |
mgal/s |
| 440 |
mgal/min |
| 441 |
mgal/h |
| 442 |
mgal/d |
| 443 |
kbbl/s |
| 444 |
kbbl/min |
| 445 |
kbbl/h |
| 446 |
kbbl/d |
| 447 |
bbl/s |
| 448 |
bbl/min |
| 449 |
bbl/h |
| 450 |
bbl/d |
| 451 |
mbbl/s |
| 452 |
mbbl/min |
| 453 |
mbbl/h |
| 454 |
mbbl/d |
| 455 |
ubbl/s |
| 456 |
ubbl/min |
| 457 |
ubbl/h |
| 458 |
ubbl/d |
| 459 |
calorific flow unit |
| 460 |
MJ/min |
| 461 |
MJ/h |
| 462 |
kJ/s |
| 463 |
kJ/min |
| 464 |
kJ/h |
| 465 |
kJ/d |
| 466 |
J/s |
| 467 |
J/min |
| 468 |
J/h |
| 469 |
J/d |
| 470 |
kcal/s |
| 471 |
kcal/min |
| 472 |
kcal/h |
| 473 |
kcal/d |
| 474 |
cal/s |
| 475 |
cal/min |
| 476 |
cal/h |
| 477 |
cal/d |
| 478 |
BTU/s |
| 479 |
BTU/min |
| 480 |
BTU/h |
| 481 |
BTU/d |
| 482 |
Mass flow unit |
| 483 |
t/s |
| 484 |
t/min |
| 485 |
t/h |
| 486 |
t/d |
| 487 |
kg/s |
| 488 |
kg/min |
| 489 |
kg/h |
| 490 |
kg/d |
| 491 |
g/s |
| 492 |
g/min |
| 493 |
g/h |
| 494 |
g/d |
| 495 |
klb/s |
| 496 |
klb/min |
| 497 |
klb/h |
| 498 |
klb/d |
| 499 |
lb/s |
| 500 |
lb/min |
| 501 |
lb/h |
| 502 |
lb/d |
| 503 |
Range information |
| 504 |
No multi range |
| 505 |
[F1] |
| 506 |
[F2] |
| 507 |
[F3] |
| 508 |
[F4] |
| 509 |
[R1] |
| 510 |
[R2] |
| 511 |
[R3] |
| 512 |
[R4] |
| 513 |
[ABS] |
| 514 |
Disp flowrate |
| 515 |
Disp flowrate% |
| 516 |
Flow noise value |
| 517 |
AO2 current |
| 518 |
mA |
| 519 |
5.3f |
| 520 |
Flow rate |
| 521 |
AO1 current |
| 522 |
8d |
| 523 |
Language |
| 524 |
English |
| 525 |
French |
| 526 |
German |
| 527 |
Italian |
| 528 |
Spanish |
| 529 |
Portuguese |
| 530 |
Russian |
| 531 |
Chinese |
| 532 |
Japanese |
| 533 |
Volume flow damping AO/frequency |
| 534 |
Volume flow damping pulse/total |
| 535 |
Ml(Megaliter) |
| 536 |
m3 |
| 537 |
kl(Kiloliter) |
| 538 |
l(liter) |
| 539 |
cm3 |
| 540 |
kcf |
| 541 |
cf |
| 542 |
mcf |
| 543 |
Mgal(US) |
| 544 |
kgal(US) |
| 545 |
gal(US) |
| 546 |
mgal(US) |
| 547 |
kbbl(US Oil) |
| 548 |
bbl(US Oil) |
| 549 |
mbbl(US Oil) |
| 550 |
ubbl(US Oil) |
| 551 |
kbbl(US Beer) |
| 552 |
bbl(US Beer) |
| 553 |
mbbl(US Beer) |
| 554 |
ubbl(US Beer) |
| 555 |
Time unit |
| 556 |
/s |
| 557 |
/min |
| 558 |
/h |
| 559 |
/d |
| 560 |
Volume flow span |
| 561 |
Execute |
| 562 |
Autozero progress |
| 563 |
Velocity damping AO/frequency |
| 564 |
Velocity damping pulse/total |
| 565 |
Mass flow damping AO/frequency |
| 566 |
Mass flow damping pulse/total |
| 567 |
Calorific value damping AO/frequency |
| 568 |
Calorific value damping pulse/total |
| 569 |
Low MF |
| 570 |
5.4f |
| 571 |
High MF |
| 572 |
Low MF EDF |
| 573 |
High MF EDF |
| 574 |
Measure mode |
| 575 |
Standard DF |
| 576 |
Enhanced DF |
| 577 |
Nominal size unit |
| 578 |
mm |
| 579 |
inch |
| 580 |
Nominal size |
| 581 |
Velocity unit |
| 582 |
m/s |
| 583 |
ft/s |
| 584 |
t |
| 585 |
kg |
| 586 |
g |
| 587 |
klb |
| 588 |
lb |
| 589 |
MJ |
| 590 |
kJ |
| 591 |
kcal |
| 592 |
cal |
| 593 |
BTU |
| 594 |
Velocity span |
| 595 |
Mass flow span |
| 596 |
Calorific flow span |
| 597 |
Velocity check |
| 598 |
User span select AO1 |
| 599 |
No |
| 600 |
Yes |
| 601 |
User unit AO1 |
| 602 |
User span AO1 |
| 603 |
User span select AO2 |
| 604 |
User unit AO2 |
| 605 |
User span AO2 |
| 606 |
Zero value |
| 607 |
Total1 unit |
| 608 |
klb(US) |
| 609 |
lb(US) |
| 610 |
Total1 conv factor |
| 611 |
Total1 low cut |
| 612 |
Total1 fail opts |
| 613 |
Measured value |
| 614 |
Stop |
| 615 |
Last valid |
| 616 |
Total1 options |
| 617 |
Balanced |
| 618 |
Absolute |
| 619 |
Only positive |
| 620 |
Only negative |
| 621 |
Hold |
| 622 |
Total1 Start/Stop |
| 623 |
Start |
| 624 |
Total1 Reset/Preset |
| 625 |
Reset |
| 626 |
Preset |
| 627 |
Total1 preset value |
| 628 |
Total1 set point |
| 629 |
Total1 count unit |
| 630 |
Total2 unit |
| 631 |
Total2 conv factor |
| 632 |
Total2 low cut |
| 633 |
Total2 fail opts |
| 634 |
Total2 options |
| 635 |
Total2 Start/Stop |
| 636 |
Total2 Reset/Preset |
| 637 |
Total2 preset value |
| 638 |
Total2 set point |
| 639 |
Total2 count unit |
| 640 |
Total3 unit |
| 641 |
Total3 conv factor |
| 642 |
Total3 low cut |
| 643 |
Total3 fail opts |
| 644 |
Total3 options |
| 645 |
Total3 Start/Stop |
| 646 |
Total3 Reset/Preset |
| 647 |
Total3 preset value |
| 648 |
Total3 set point |
| 649 |
Total3 count unit |
| 650 |
Totalizer reset mode |
| 651 |
Pulse1 output mode |
| 652 |
Fixed pulse output |
| 653 |
Frequency output |
| 654 |
Status output |
| 655 |
Pulse1 active mode |
| 656 |
On active |
| 657 |
Off active |
| 658 |
Pulse1 fix width |
| 659 |
0.05ms |
| 660 |
0.1ms |
| 661 |
0.5ms |
| 662 |
1ms |
| 663 |
20ms |
| 664 |
33ms |
| 665 |
50ms |
| 666 |
100ms |
| 667 |
200ms |
| 668 |
330ms |
| 669 |
500ms |
| 670 |
1000ms |
| 671 |
2000ms |
| 672 |
Duty cycle 50% |
| 673 |
Pulse1 rate unit |
| 674 |
n unit/P |
| 675 |
u unit/P |
| 676 |
m unit/P |
| 677 |
Unit/P |
| 678 |
k unit/P |
| 679 |
M unit/P |
| 680 |
n P/unit |
| 681 |
u P/unit |
| 682 |
m P/unit |
| 683 |
P/unit |
| 684 |
k P/unit |
| 685 |
M P/unit |
| 686 |
Pulse1 rate value |
| 687 |
Pulse1 low cut |
| 688 |
Pulse1 alarm out |
| 689 |
0 pps |
| 690 |
Max pps |
| 691 |
Frequency1 at 0% |
| 692 |
5d |
| 693 |
Frequency1 at 100% |
| 694 |
Pulse1 option |
| 695 |
Pulse2 active pulse |
| 696 |
Normal |
| 697 |
For magnetic counter |
| 698 |
Pulse2 output mode |
| 699 |
Pulse2 active mode |
| 700 |
Pulse2 fix width |
| 701 |
Pulse2 rate unit |
| 702 |
Pulse2 rate value |
| 703 |
Pulse2 low cut |
| 704 |
Pulse2 alarm out |
| 705 |
Frequency2 at 0% |
| 706 |
Frequency2 at 100% |
| 707 |
Pulse2 option |
| 708 |
Status output3 active mode |
| 709 |
Status input3 active mode |
| 710 |
Short(On) act |
| 711 |
Open(Off) act |
| 712 |
Status input3 state |
| 713 |
Open |
| 714 |
Short |
| 715 |
Status input3 function |
| 716 |
0% Signal Lock |
| 717 |
Ext auto zero |
| 718 |
Tolal preset 1 |
| 719 |
Total preset 2 |
| 720 |
Total preset 3 |
| 721 |
Ext2 ranges |
| 722 |
0% Signal Lock 2 |
| 723 |
Forward span 2 |
| 724 |
Reverse span 1 |
| 725 |
Reverse span 2 |
| 726 |
Auto range hyst |
| 727 |
2d |
| 728 |
Bi direction hyst |
| 729 |
AO1 low cut |
| 730 |
AO1 high limit |
| 731 |
AO1 low limit |
| 732 |
AO1 alarm out |
| 733 |
<2.4mA |
| 734 |
3.8mA |
| 735 |
4mA |
| 736 |
20.5mA |
| 737 |
>21.6mA |
| 738 |
AO1 range mode |
| 739 |
Normal range |
| 740 |
Abs range |
| 741 |
AO2 low cut |
| 742 |
AO2 high limit |
| 743 |
AO2 low limit |
| 744 |
AO2 alarm out |
| 745 |
AI function |
| 746 |
Monitoring |
| 747 |
Diff temperature |
| 748 |
Ext temperature |
| 749 |
AI high limit |
| 750 |
AI low limit |
| 751 |
AI current |
| 752 |
AI unit |
| 753 |
deg C |
| 754 |
deg F |
| 755 |
K |
| 756 |
AI URV |
| 757 |
AI LRV |
| 758 |
AO1 trim clear |
| 759 |
Not exectute |
| 760 |
AO1 trim 4mA |
| 761 |
AO1 trim 20mA |
| 762 |
AO2 trim clear |
| 763 |
AO2 trim 4mA |
| 764 |
AO2 trim 20mA |
| 765 |
AI trim clear |
| 766 |
AI trim 4mA |
| 767 |
AI trim 20mA |
| 768 |
Flow direction |
| 769 |
Forward |
| 770 |
Reverse |
| 771 |
Rate limit |
| 772 |
3.1f |
| 773 |
Dead time |
| 774 |
Noise filter |
| 775 |
Manual |
| 776 |
Pulsing flow |
| 777 |
Power synchronize |
| 778 |
Set power frequency |
| 779 |
4.2f |
| 780 |
IEX power frequency |
| 781 |
Measured power frequency |
| 782 |
6.2f |
| 783 |
Set SIL |
| 784 |
Density unit |
| 785 |
kg/m3 |
| 786 |
lb/gal |
| 787 |
lb/cf |
| 788 |
Density fixed value |
| 789 |
Standard density |
| 790 |
Standard temperature |
| 791 |
5.2f |
| 792 |
Temp coef A1 |
| 793 |
Temp coef A2 |
| 794 |
Measured temperature |
| 795 |
Correct density |
| 796 |
Specific heat |
| 797 |
J/kg*K |
| 798 |
6.1f |
| 799 |
Calorific fix temp |
| 800 |
Low alarm |
| 801 |
High alarm |
| 802 |
Low low alarm |
| 803 |
High high alarm |
| 804 |
Hi/Lo alarm hysteresis |
| 805 |
2.0f |
| 806 |
Burn out |
| 807 |
High |
| 808 |
Low |
| 809 |
Alarm out mask 1 |
| 810 |
13:Main board EEPROM default on |
| 811 |
21:PWM1 stop on |
| 812 |
22:PWM2 stop on |
| 813 |
23:Option board mismatch on |
| 814 |
24:Option EEPROM failure on |
| 815 |
25:Option board A/D failure on |
| 816 |
26:Option board SPI failure on |
| 817 |
28:Indicator board failure on |
| 818 |
29:Ind EEP FAIL on |
| 819 |
30:LCD driver failure on |
| 820 |
31:Indicator board mismatch on |
| 821 |
32:Indicator communication error on |
| 822 |
33:microSD card failure on |
| 823 |
Alarm out mask 4 |
| 824 |
130:Device ID not entered on |
| 825 |
Alarm record mask 1 |
| 826 |
Alarm record mask 2 |
| 827 |
50:Signal overflow on |
| 828 |
51:Empty pipe detection on |
| 829 |
52:H/L HH/LL alarm on |
| 830 |
53:Adhesion over level 4 on |
| 831 |
85:Cable misconnect on |
| 832 |
Alarm record mask 3 |
| 833 |
125:Data logging clear on |
| 834 |
Alarm record 1 |
| 835 |
16:A/D 1 failure[Signal] FAIL |
| 836 |
17:A/D 2 failure[Exciter] FAIL |
| 837 |
32:Indicator board communication error |
| 838 |
Alarm record time 1 |
| 839 |
Alarm record 2 |
| 840 |
24:Option board EEPROM Failure |
| 841 |
Alarm record time 2 |
| 842 |
Alarm record 3 |
| 843 |
Alarm record time 3 |
| 844 |
Alarm record 4 |
| 845 |
Alarm record time 4 |
| 846 |
Display format PV |
| 847 |
Auto |
| 848 |
0 digit |
| 849 |
1 digit |
| 850 |
2 digit |
| 851 |
3 digit |
| 852 |
4 digit |
| 853 |
5 digit |
| 854 |
Auto 2 |
| 855 |
Display format total 1 |
| 856 |
6 digit |
| 857 |
7 digit |
| 858 |
Display format total 2 |
| 859 |
Display format total 3 |
| 860 |
Display contrast |
| 861 |
-5 |
| 862 |
-4 |
| 863 |
-3 |
| 864 |
-2 |
| 865 |
-1 |
| 866 |
0 |
| 867 |
+1 |
| 868 |
+2 |
| 869 |
+3 |
| 870 |
+4 |
| 871 |
+5 |
| 872 |
Display line |
| 873 |
1 Line(Big) |
| 874 |
1 Line |
| 875 |
2 Line |
| 876 |
3 Line |
| 877 |
4 Line |
| 878 |
Display period |
| 879 |
0.2s |
| 880 |
0.4s |
| 881 |
1.0s |
| 882 |
2.0s |
| 883 |
4.0s |
| 884 |
8.0s |
| 885 |
Display NE107 |
| 886 |
NE107 |
| 887 |
Display alarm |
| 888 |
Detail |
| 889 |
Display scroll |
| 890 |
Auto(2s) |
| 891 |
Auto(4s) |
| 892 |
Auto(8s) |
| 893 |
Display damping |
| 894 |
Display format date |
| 895 |
MM/DD/YYYY |
| 896 |
DD/MM/YYYY |
| 897 |
YYYY/MM/DD |
| 898 |
Display measure mode |
| 899 |
Trend |
| 900 |
Trend offline urv |
| 901 |
Trend offline lrv |
| 902 |
Trend select 1 |
| 903 |
Trend select 2 |
| 904 |
Trend select 3 |
| 905 |
Trend select 4 |
| 906 |
Display inversion |
| 907 |
Invert |
| 908 |
LCD test |
| 909 |
Show Pattern1 |
| 910 |
Show Pattern2 |
| 911 |
Show Pattern3 |
| 912 |
Show Pattern4 |
| 913 |
Squawk once |
| 914 |
Language package |
| 915 |
Package1 |
| 916 |
Package2 |
| 917 |
Display installation |
| 918 |
No disp |
| 919 |
With disp |
| 920 |
IRSW operation |
| 921 |
Display time |
| 922 |
Current time |
| 923 |
Operation days |
| 924 |
Operation time |
| 925 |
Transmitter type |
| 926 |
Non |
| 927 |
1A Type |
| 928 |
4A Type |
| 929 |
Option board ID |
| 930 |
Multi |
| 931 |
Multi(SI+SO) |
| 932 |
Reserved |
| 933 |
IS |
| 934 |
Electrode size |
| 935 |
1 mm |
| 936 |
3 mm |
| 937 |
8 mm |
| 938 |
10 mm |
| 939 |
6 mm |
| 940 |
IO1 |
| 941 |
NAN |
| 942 |
AO1 Act |
| 943 |
AO1 Pas |
| 944 |
AO2 Act |
| 945 |
AI Act |
| 946 |
AI Pas |
| 947 |
PLS/SO2 Pas |
| 948 |
PLS/SO2 Act1 |
| 949 |
PLS/SO2 Act2/3 |
| 950 |
IO2 |
| 951 |
PLS/SO1 Pas |
| 952 |
NM1 |
| 953 |
IO3 |
| 954 |
AO2 Pas |
| 955 |
SO3 Pas |
| 956 |
SI3 V-Free |
| 957 |
Modbus(GND) |
| 958 |
Basic model code |
| 959 |
Suffix config 1 |
| 960 |
Suffix config 2 |
| 961 |
Option 1 |
| 962 |
Option 2 |
| 963 |
Option 3 |
| 964 |
Option 4 |
| 965 |
Remote sensor basic model code |
| 966 |
Remote sensor suffix config 1 |
| 967 |
Remote sensor suffix config 2 |
| 968 |
Remote sensor option 1 |
| 969 |
Remote sensor option 2 |
| 970 |
Remote sensor option 3 |
| 971 |
Remote sensor option 4 |
| 972 |
Transmitter serial No |
| 973 |
Sensor serial No |
| 974 |
Memo 1 |
| 975 |
Memo 2 |
| 976 |
Memo 3 |
| 977 |
Main board revision |
| 978 |
Sensor board revision |
| 979 |
Indicator board revision |
| 980 |
Adhesion function |
| 981 |
Adhesion level 1 |
| 982 |
M ohm |
| 983 |
Adhesion level 2 |
| 984 |
Adhesion level 3 |
| 985 |
Adhesion level 4 |
| 986 |
Adhesion value |
| 987 |
Adhesion status |
| 988 |
Adhesion check cycle |
| 989 |
0.5 min |
| 990 |
1 min |
| 991 |
2 min |
| 992 |
10 min |
| 993 |
VF execution max time |
| 994 |
VF execution progress |
| 995 |
% |
| 996 |
VF execution status |
| 997 |
diag exe progress |
| 998 |
diag exe finish sts |
| 999 |
IEX output |
| 1000 |
Coil insulation threshold |
| 1001 |
IEX compare |
| 1002 |
IEX coil resistance |
| 1003 |
ohm |
| 1004 |
5.1f |
| 1005 |
Electrode voltage A |
| 1006 |
3.2f |
| 1007 |
Electrode voltage B |
| 1008 |
Empty status |
| 1009 |
Full |
| 1010 |
Empty |
| 1011 |
VF target select |
| 1012 |
Magnetic |
| 1013 |
Excitation |
| 1014 |
Calculation |
| 1015 |
Device status |
| 1016 |
Conn status |
| 1017 |
Diagnostic output |
| 1018 |
Zero |
| 1019 |
VF mode |
| 1020 |
No flow |
| 1021 |
Flow |
| 1022 |
VF No |
| 1023 |
Factory |
| 1024 |
Previous |
| 1025 |
Present |
| 1026 |
VF check result |
| 1027 |
Passed |
| 1028 |
Failed |
| 1029 |
Canceled |
| 1030 |
No Data |
| 1031 |
Unknown |
| 1032 |
VF operation time |
| 1033 |
Magnetic circuit result |
| 1034 |
Skip |
| 1035 |
Excitation circuit result |
| 1036 |
VF device status result |
| 1037 |
Connection status result |
| 1038 |
Calculation circuit result |
| 1039 |
Release time |
| 1040 |
30 min |
| 1041 |
1 h |
| 1042 |
3 h |
| 1043 |
12 h |
| 1044 |
AO1 |
| 1045 |
Pulse1 |
| 1046 |
pps |
| 1047 |
SO1 |
| 1048 |
Close |
| 1049 |
AO2 |
| 1050 |
Pulse2 |
| 1051 |
SO2 |
| 1052 |
AI |
| 1053 |
SO3 |
| 1054 |
SI3 |
| 1055 |
Test 2 mode |
| 1056 |
Test |
| 1057 |
Test 2 output value |
| 1058 |
Factory backup name |
| 1059 |
Factory backup date |
| 1060 |
SD backup name |
| 1061 |
Backup name 1 |
| 1062 |
Backup date 1 |
| 1063 |
Backup name 2 |
| 1064 |
Backup date 2 |
| 1065 |
Backup name 3 |
| 1066 |
Backup date 3 |
| 1067 |
Backup execute |
| 1068 |
Store Main to 1 |
| 1069 |
Store Main to 2 |
| 1070 |
Store Main to 3 |
| 1071 |
Store Main to SD |
| 1072 |
Store EEP1 to SD |
| 1073 |
Store EEP2 to SD |
| 1074 |
Store EEP3 to SD |
| 1075 |
Restore execute |
| 1076 |
Duplicate Data1 |
| 1077 |
Duplicate Data2 |
| 1078 |
Duplicate Data3 |
| 1079 |
Duplicate SD |
| 1080 |
Restore Data1 |
| 1081 |
Restore Data2 |
| 1082 |
Restore Data3 |
| 1083 |
Restore SD |
| 1084 |
Compulsion Data1 |
| 1085 |
Compulsion Data2 |
| 1086 |
Compulsion Data3 |
| 1087 |
Compulsion SD |
| 1088 |
Restore Factory |
| 1089 |
Restore result |
| 1090 |
Unexecuted |
| 1091 |
Success |
| 1092 |
Fail |
| 1093 |
running |
| 1094 |
File name |
| 1095 |
Interval time |
| 1096 |
1 s |
| 1097 |
10 s |
| 1098 |
30 s |
| 1099 |
5 min |
| 1100 |
Start time |
| 1101 |
Start date |
| 1102 |
End time |
| 1103 |
24 h |
| 1104 |
72 h |
| 1105 |
240 h |
| 1106 |
720 h |
| 1107 |
1440 h |
| 1108 |
Logging Exe |
| 1109 |
Key code |
| 1110 |
4d |
| 1111 |
Write protect |
| 1112 |
Enable write 10min |
| 1113 |
New password |
| 1114 |
Software seal |
| 1115 |
Keep |
| 1116 |
Break |
| 1117 |
no_unit |
| 1118 |
|
| 1119 |
fix_unit_cm |
| 1120 |
Valid status |
| 1121 |
Burst Command number for edit |
| 1122 |
Event Notification retry time for edit |
| 1123 |
Event Notification maximum update time for edit |
| 1124 |
Event Notification de-bounce interval for edit |
| 1125 |
Burst Message update period for edit |
| 1126 |
Burst Message max update period for edit |
| 1127 |
Burst Message trigger mode for edit |
| 1128 |
Burst Message trigger classification for edit |
| 1129 |
Burst Message trigger units for edit |
| 1130 |
Burst Message trigger level for edit |
| 1131 |
Device Status Mask for edit |
| 1132 |
Status Group 0 Mask for edit |
| 1133 |
Status Group 1 Mask for edit |
| 1134 |
Status Group 2 Mask for edit |
| 1135 |
Status Group 3 Mask for edit |
| 1136 |
Status Group 4 Mask for edit |
| 1137 |
Status Group 5 Mask for edit |
| 1138 |
Status Group 14 Mask for edit |
| 1139 |
Status Group 15 Mask for edit |
| 1140 |
Status Group 16 Mask for edit |
| 1141 |
Status Group 17 Mask for edit |
| 1142 |
Status Group 18 Mask for edit |
| 1143 |
Status Group 19 Mask for edit |
| 1144 |
Status Group 20 Mask for edit |
| 1145 |
Ext Dev status Mask for edit |
| 1146 |
Dev Diag Status 0 Mask for edit |
| 1147 |
Dev Diag Status 1 Mask for edit |
| 1148 |
Dev Diag Status 2 Mask for edit |
| 1149 |
analog channel saturated Mask for edit |
| 1150 |
analog channel fixed Mask for edit |
| 1151 |
Explosion protection |
| 1152 |
1 |
| 1153 |
2 |
| 1154 |
3 |
| 1155 |
4 |
| 1156 |
5 |
| 1157 |
6 |
| 1158 |
7 |
| 1159 |
8 |
| 1160 |
9 |
| 1161 |
10 |
| 1162 |
11 |
| 1163 |
12 |
| 1164 |
13 |
| 1165 |
14 |
| 1166 |
15 |
| 1167 |
16 |
| 1168 |
17 |
| 1169 |
18 |
| 1170 |
19 |
| 1171 |
20 |
| 1172 |
Select MS code |
| 1173 |
Test mode |
| 1174 |
Velocity test on |
| 1175 |
Volume flow test on |
| 1176 |
Mass flow test on |
| 1177 |
Calorific value test on |
| 1178 |
AO1 test on |
| 1179 |
Pulse1 test on |
| 1180 |
SO1 test on |
| 1181 |
AO2 test on |
| 1182 |
Pulse2 test on |
| 1183 |
SO2 test on |
| 1184 |
AI test on |
| 1185 |
SO3 test on |
| 1186 |
SI3 test on |
| 1187 |
SO11 test on |
| 1188 |
SI11 test on |
| 1189 |
SO12 test on |
| 1190 |
SI12 test on |
| 1191 |
Alm test on |
| 1192 |
Forward span 3 |
| 1193 |
Forward span 4 |
| 1194 |
Reverse span 3 |
| 1195 |
Reverse span 4 |
| 1196 |
Status output11 active mode |
| 1197 |
Status output11 function |
| 1198 |
Auto3 range |
| 1199 |
Auto4 range |
| 1200 |
Ext3 answer |
| 1201 |
Ext4 answer |
| 1202 |
Status input11 active mode |
| 1203 |
Status input11 function |
| 1204 |
Total preset1 |
| 1205 |
Total preset2 |
| 1206 |
Total preset3 |
| 1207 |
Ext3 ranges |
| 1208 |
Ext4 ranges |
| 1209 |
Status input11 state |
| 1210 |
Status output12 active mode |
| 1211 |
Status output12 function |
| 1212 |
Status input12 active mode |
| 1213 |
Status input12 function |
| 1214 |
Status input12 state |
| 1215 |
SO11 |
| 1216 |
Alarm out mask 2 |
| 1217 |
60:Span configuration error on |
| 1218 |
61:PV flow configuration error on |
| 1219 |
62:Analog output 1 4-20mA limit error on |
| 1220 |
63:Analog output 2 4-20mA limit error on |
| 1221 |
64:Analog output 1 multi range error on |
| 1222 |
65:H/L HH/LL configuration error on |
| 1223 |
66:Density configuration error on |
| 1224 |
67:Pulse output 1 configuration error on |
| 1225 |
68:Pulse output 2 configuration error on |
| 1226 |
69:Nominal size configuration error on |
| 1227 |
70:Adhesion configuration error on |
| 1228 |
71:Flow noise config error on |
| 1229 |
72:Data logging not started on |
| 1230 |
80:Analog output 1 saturated on |
| 1231 |
81:Analog output 2 saturated on |
| 1232 |
82:Pulse output 1 saturated on |
| 1233 |
83:Pulse output 2 saturated on |
| 1234 |
84:Analog input saturated on |
| 1235 |
86:Coil insulation warning on |
| 1236 |
131:Transmitter type mismatch on |
| 1237 |
Alarm out mask 3 |
| 1238 |
87:Adhesion over level 3 on |
| 1239 |
88:Low conductivity warning on |
| 1240 |
89:Insulation detection on |
| 1241 |
90:Flow noise over level 3 on |
| 1242 |
91:Flow noise over level 4 on |
| 1243 |
92:Autozero warning on |
| 1244 |
93:Verification warning on |
| 1245 |
94:Factory noise warning on |
| 1246 |
95:Simulation active on |
| 1247 |
96:Analog output 1 fixed on |
| 1248 |
97:Analog output 2 fixed on |
| 1249 |
98:Pulse output 1 fixed on |
| 1250 |
99:Pulse output 2 fixed on |
| 1251 |
100:Analog input fixed on |
| 1252 |
101:Parameter restore running on |
| 1253 |
102:Display over warning on |
| 1254 |
103:microSD card size warning on |
| 1255 |
104:Parameter backup incomplete on |
| 1256 |
105:microSD card mismatch on |
| 1257 |
106:microSD card removal error on |
| 1258 |
120:Watchdog on |
| 1259 |
121:Power off on |
| 1260 |
122:Instant power failure on |
| 1261 |
123:Parameter backup running on |
| 1262 |
124:Data logging running on |
| 1263 |
SI11 |
| 1264 |
SO12 |
| 1265 |
SI12 |
| 1266 |
Alarm |
| 1267 |
Flow sensor select |
| 1268 |
ADMAG AXG |
| 1269 |
ADMAG AXW |
| 1270 |
ADMAG AXF |
| 1271 |
ADMAG |
| 1272 |
ADMAG AE |
| 1273 |
ADMAG SE |
| 1274 |
YEWMAG |
| 1275 |
Calibrator |
| 1276 |
Other1 |
| 1277 |
Other2 |
| 1278 |
Other3 |
| 1279 |
MIO |
| 1280 |
NM2 |
| 1281 |
Modbus |
| 1282 |
Alarm output active mode |
| 1283 |
Burst Variable SLOT for edit |
| 1284 |
User_unit1 |
| 1285 |
User_unit2 |
| 1286 |
user unit2 |
| 1287 |
Calorific flow |
| 1288 |
No_connect |
| 1289 |
Velecity |
| 1290 |
User Unit2(calorie) |
| 1291 |
Not write protect mode |
| 1292 |
Change PV map |
| 1293 |
Change SV map |
| 1294 |
Change TV map |
| 1295 |
Change QV map |
| 1296 |
Aborting |
| 1297 |
Exiting |
| 1298 |
Set Date/Time |
| 1299 |
Set current date and time. |
| 1300 |
Reset cfg chng flag |
| 1301 |
Autozero Exe |
| 1302 |
Device variable simulation |
| 1303 |
Enable device variable simulation |
| 1304 |
Device status bit simulation |
| 1305 |
AO1 trim |
| 1306 |
AO2 trim |
| 1307 |
Clear D/A trim 1 |
| 1308 |
Clear D/A trim 2 |
| 1309 |
AI trim |
| 1310 |
Clear AI trim |
| 1311 |
Backup Exe |
| 1312 |
Restore Exe |
| 1313 |
Pulse/Status out 1 |
| 1314 |
Display setting |
| 1315 |
Reset condensed status map |
| 1316 |
Verification Exe |
| 1317 |
Diagnostic Exe |
| 1318 |
Stop burst |
| 1319 |
Stop burst messages |
| 1320 |
Stop easy burst |
| 1321 |
Stop easy burst messages |
| 1322 |
Set easy burst |
| 1323 |
Setup easy burst message |
| 1324 |
stop Detailed Burst |
| 1325 |
Stop Detailed Burst Message |
| 1326 |
set Detailed Burst |
| 1327 |
Setup Detailed Burst Messages |
| 1328 |
Sub Routine for Burst setting 103 edit |
| 1329 |
Sub Routine for Burst setting 103 write |
| 1330 |
Sub Routine for Burst setting 104 edit |
| 1331 |
Sub Routine for Burst setting 104 write |
| 1332 |
Sub Routine for Burst setting 107 edit |
| 1333 |
Sub Routine for Burst setting 107 write |
| 1334 |
Sub Routine for Burst setting 108 edit |
| 1335 |
Sub Routine for Burst setting 108 write |
| 1336 |
Sub Routine for Burst Message turn OFF |
| 1337 |
Sub Routine for Burst Message turn ON |
| 1338 |
Sub Routine for Burst Slots |
| 1339 |
Sub Routine for Burst Target Command |
| 1340 |
Sub Routine for Burst Period |
| 1341 |
Sub Routine for Burst Get DV-code |
| 1342 |
Sub Routine for Burst Trigger |
| 1343 |
stop Event |
| 1344 |
Stop Event Notification |
| 1345 |
set Event |
| 1346 |
Setup Event Notification |
| 1347 |
acknowledge Event |
| 1348 |
Acknowledge Event Notification |
| 1349 |
Sub Routine for Event Notification turn OFF |
| 1350 |
Sub Routine for Event Notification turn ON |
| 1351 |
Sub Routine for Event setting 116 edit |
| 1352 |
Sub Routine for Event setting 116 write |
| 1353 |
Sub Routine for Event setting 117 write |
| 1354 |
Sub Routine for Event Timing |
| 1355 |
Sub Routine for Event Status Mask |
| 1356 |
Online |
| 1357 |
Process variables root menu |
| 1358 |
Diagnostic root menu |
| 1359 |
Maintenance root menu |
| 1360 |
Device root menu |
| 1361 |
Current alarm |
| 1362 |
Dynamic variables |
| 1363 |
Dynamic variables unit |
| 1364 |
Device variables |
| 1365 |
Device variables status |
| 1366 |
Totalizer count |
| 1367 |
View outputs |
| 1368 |
View inputs |
| 1369 |
Status/Self test |
| 1370 |
Alarm/Event device status |
| 1371 |
Condensed status map |
| 1372 |
Status group 0 |
| 1373 |
Status group 1 |
| 1374 |
Status group 2 |
| 1375 |
Status group 3 |
| 1376 |
Status group 4 |
| 1377 |
Status group 5 |
| 1378 |
Ext dev status |
| 1379 |
Device Diagnostic Status 0 |
| 1380 |
Device Diagnostic Status 1 |
| 1381 |
AO saturated |
| 1382 |
I/O and Subdevice Status |
| 1383 |
WirelessHART Status |
| 1384 |
AO fixed |
| 1385 |
Status group 14 |
| 1386 |
Status group 15 |
| 1387 |
Status group 16 |
| 1388 |
Status group 17 |
| 1389 |
Status group 18 |
| 1390 |
Status group 19 |
| 1391 |
Status group 20 |
| 1392 |
Alarm record mask |
| 1393 |
Alarm record |
| 1394 |
Alarm out mask |
| 1395 |
Time stamp |
| 1396 |
Diagnosis |
| 1397 |
Result |
| 1398 |
Conductivity |
| 1399 |
Verification |
| 1400 |
Autozero |
| 1401 |
AO/AI trim |
| 1402 |
AO trim |
| 1403 |
High/Low alarm configuration |
| 1404 |
Input test |
| 1405 |
Output test |
| 1406 |
Param bkup/restore |
| 1407 |
Data logging |
| 1408 |
Display indication |
| 1409 |
Easy setup wizard |
| 1410 |
Basic setup |
| 1411 |
Detailed setup |
| 1412 |
Process variables |
| 1413 |
Density |
| 1414 |
Temperature |
| 1415 |
Sensor |
| 1416 |
User span |
| 1417 |
Totalizer |
| 1418 |
Pulse/Status |
| 1419 |
Pulse/Status output 1 |
| 1420 |
Pulse/Status output 2 |
| 1421 |
Status output 3 |
| 1422 |
Status input 3 |
| 1423 |
Status output 11 |
| 1424 |
Status output 12 |
| 1425 |
Status input 11 |
| 1426 |
Status input 12 |
| 1427 |
Analog output/input |
| 1428 |
Analog output 1 |
| 1429 |
Analog output 2 |
| 1430 |
Analog input |
| 1431 |
Multi range |
| 1432 |
AUX calculation |
| 1433 |
Display |
| 1434 |
Line select |
| 1435 |
Trend select |
| 1436 |
Display format |
| 1437 |
Display operation configuration |
| 1438 |
Device information |
| 1439 |
Order information |
| 1440 |
Version/Number information |
| 1441 |
Memo |
| 1442 |
HART setup |
| 1443 |
Burst setup |
| 1444 |
Easy burst setup |
| 1445 |
Detailed burst setup |
| 1446 |
BM1 Setting |
| 1447 |
BM2 Setting |
| 1448 |
BM3 Setting |
| 1449 |
Event setup |
| 1450 |
Event Setting |
| 1451 |
Protection |
| 1452 |
Upload variables |
| 1453 |
Offline root menu |
| 1454 |
IO Status |
| 1455 |
Status Bit Not Supported |
| 1456 |
No Effect |
| 1457 |
Maintenance Required |
| 1458 |
Used to map a status condition to a severity level. |
| 1459 |
PV Analog Channel Saturated |
| 1460 |
PV Analog Channel Fixed |
| 1461 |
Critical Power Failure |
| 1462 |
Simulation Active |
| 1463 |
Non-Volatile memory failure |
| 1464 |
Volatile memory error |
| 1465 |
Watchdog reset executed |
| 1466 |
Voltage conditions out of range |
| 1467 |
Environmental conditions out of range |
| 1468 |
Electronic failure |
| 1469 |
Discrete Variable Simulation active |
| 1470 |
Secondary Analog Channel Saturated |
| 1471 |
Tertiary Analog Channel Saturated |
| 1472 |
Quaternary Analog Channel Saturated |
| 1473 |
Quinary Analog Channel Saturated |
| 1474 |
Subdevice list changed |
| 1475 |
Duplicate master detected |
| 1476 |
Subdevice mismatch |
| 1477 |
Subdevice with duplicate IDs found |
| 1478 |
Stale data notice |
| 1479 |
Capacity Denied |
| 1480 |
Bandwidth allocation pending |
| 1481 |
Block transfer pending |
| 1482 |
Secondary Analog Channel Fixed |
| 1483 |
Tertiary Analog Channel Fixed |
| 1484 |
Quaternary Analog Channel Fixed |
| 1485 |
Quinary Analog Channel Fixed |
| 1486 |
126:microSD card insert |
| 1487 |
127:microSD card removed |
| 1488 |
Starting Status Map Index must be even value. |
| 1489 |
Condensed status value |
| 1490 |
Allows simulation of different status conditions. |
| 1491 |
Clear |
| 1492 |
Set |
| 1493 |
Bit Index |
| 1494 |
Common Tables |
| 1495 |
Interoperable * |
| 1496 |
Universal |
| 1497 |
Common Practice |
| 1498 |
Pressure Universal |
| 1499 |
Pressure Common |
| 1500 |
Menu |
| 1501 |
Rosemount Magflow |
| 1502 |
Rosemount Pressure |
| 1503 |
Moore Products |
| 1504 |
Siemens Pressure |
| 1505 |
P2 Common |
| 1506 |
Wireless |
| 1507 |
Munge |
| 1508 |
Analytical Oxygen/Combustion/Methane/CO |
| 1509 |
Flow Totalizer - Rate Indicator |
| 1510 |
Flow Variable Area |
| 1511 |
Flow Coriolis Mass |
| 1512 |
Flow Ultrasonic - Gas |
| 1513 |
Flow Ultrasonic - Liquid |
| 1514 |
Level Ultrasonic |
| 1515 |
Level Radar - Microwave |
| 1516 |
Pressure Absolute |
| 1517 |
Level Capacitance |
| 1518 |
Pressure Differential |
| 1519 |
Level Hydrostatic |
| 1520 |
Level |
| 1521 |
Pressure Absolute/Relative |
| 1522 |
Level Microwave |
| 1523 |
Level Radar |
| 1524 |
Level Density - Nuclear |
| 1525 |
Flow Electromagnetic |
| 1526 |
Flow Vortex |
| 1527 |
Flow Magmeter - Rack Version |
| 1528 |
Flow High Performance Magmeter |
| 1529 |
Flow Mass |
| 1530 |
Flow Ultrasonic |
| 1531 |
Flow Magnetic |
| 1532 |
Flow Magnetic - Custody Transfer |
| 1533 |
Flow 2-wire Magnetic |
| 1534 |
Flow Coriolis Mass - Custody Transfer |
| 1535 |
Flow 2-wire Vortex |
| 1536 |
Flow Thermal |
| 1537 |
Temperature Head Mounted |
| 1538 |
Temperature Compact |
| 1539 |
Temperature DIN Rail Mounted |
| 1540 |
Analytical pH |
| 1541 |
Analytical Conductivity - Conductive |
| 1542 |
Analytical Conductivity - Inductive |
| 1543 |
Temperature Sensor |
| 1544 |
Level Servo |
| 1545 |
Temperature DIN Rail |
| 1546 |
Analytical ORP |
| 1547 |
Analytical pION |
| 1548 |
Analytical IConc |
| 1549 |
Analytical Electrode Conductivity |
| 1550 |
Analytical Toroidal Conductivity |
| 1551 |
Valve Positioner |
| 1552 |
Valve Controller |
| 1553 |
Pressure |
| 1554 |
Pressure Multivariable |
| 1555 |
Analytical pH/ORP |
| 1556 |
Flow Coriolis |
| 1557 |
Analytical Conductivity |
| 1558 |
Valve Positioner/Pneumatic |
| 1559 |
Valve Actuator - Electrical |
| 1560 |
Temperature Dual Input |
| 1561 |
Valve Actuator |
| 1562 |
Analytical Corrosion |
| 1563 |
Analytical Density - Nuclear |
| 1564 |
Level Continuous Gamma |
| 1565 |
Level Laser Ranging |
| 1566 |
Pressure Safety |
| 1567 |
Flow Vortex/Swirl |
| 1568 |
Analytical 4 Electrode Conductivity |
| 1569 |
Analytical 2 Electrode Conductivity |
| 1570 |
Analytical Troidal Conductivity |
| 1571 |
Analytical pH/ORP/pIon/Ion Conc |
| 1572 |
Analytical Oxygen |
| 1573 |
Pressure P, dP + Multivariable |
| 1574 |
Temperature 2-wire |
| 1575 |
Pressure w/ PID |
| 1576 |
Pressure Saturated Steam |
| 1577 |
Analytical Density - Gamma Ray |
| 1578 |
Level Gamma Ray |
| 1579 |
Analytical Weight - Gamma Ray |
| 1580 |
Level w/ Density - Gamma Ray |
| 1581 |
Analytical Motorized Density |
| 1582 |
Flow Multivariable Mass |
| 1583 |
Temperature Multivariable |
| 1584 |
Specialty HART-to-Analog Signal Conv |
| 1585 |
Flow dP |
| 1586 |
Pressure Low Power |
| 1587 |
Pressure Certified SIL2 |
| 1588 |
Interoperable |
| 1589 |
Analytical Density |
| 1590 |
Valve Positioner/Electropneumatic |
| 1591 |
Flow Magnetic Inductive |
| 1592 |
Analytical |
| 1593 |
Analytical Opacity Monitor |
| 1594 |
Analytical Oxygen/Combustion |
| 1595 |
Analytical 2-wire Conductivity |
| 1596 |
Analytical 2-wire Conductivity w/ pure H20 |
| 1597 |
Analytical 2-wire Conductivity w/ % conc |
| 1598 |
Analytical 2-wire Oxygen/Chlorine/Ozone |
| 1599 |
Analytical 2-wire pH/ORP |
| 1600 |
Analytical 2-wire Contacting/Toroidal |
| 1601 |
Analytical Oxygen - High Temperature |
| 1602 |
Analytical Conductivity w/ % conc |
| 1603 |
Analytical pH/ORP/ISE |
| 1604 |
Analytical Amperometric Analyzer |
| 1605 |
Analytical Dual Input Analyzer |
| 1606 |
Pressure Pressure/Level |
| 1607 |
Analytical Consistency |
| 1608 |
Analytical Microwave-Pulp Consistency |
| 1609 |
Analytical Microwave Consistency |
| 1610 |
Valve Digital Positioner |
| 1611 |
Valve Smart Valve Positioner |
| 1612 |
Temperature Differential |
| 1613 |
Analytical Dissolved Oxygen |
| 1614 |
Analytical pH Controller |
| 1615 |
Analytical Conductivity/Resistivity Controller |
| 1616 |
Analytical Conductivity/Resistivity |
| 1617 |
Level Displacement |
| 1618 |
Temperature w/ PID |
| 1619 |
Valve Universal Positioner |
| 1620 |
Level Radar - Reflex |
| 1621 |
Pressure Gauge |
| 1622 |
Pressure Sealed Gauge |
| 1623 |
Valve Digital Positioner w/ PID |
| 1624 |
Valve Intelligent Positioner |
| 1625 |
Analytical Gas Detector |
| 1626 |
Analytical Infrared Gas Detector |
| 1627 |
Analytical Electrochemical Gas Detector |
| 1628 |
Analytical Measuring Instruments |
| 1629 |
Level Magnostrictive |
| 1630 |
Valve On/Off Valve Controller |
| 1631 |
Level Radar - Pulse |
| 1632 |
Level Continuous Capactive |
| 1633 |
Valve Damper Actuator |
| 1634 |
Valve Electric Damper Actuator |
| 1635 |
Flow Electronic |
| 1636 |
Flow Vortex - Multiparameter Mass |
| 1637 |
Analytical UV Flame Detector |
| 1638 |
Analytical UVIR Flame Detector |
| 1639 |
Analytical IR Flame Detector |
| 1640 |
Analytical Fire Detector |
| 1641 |
Analytical Gas Detector Display Interface |
| 1642 |
Analytical Toxic Gas Detector |
| 1643 |
Analytical Flame Detector |
| 1644 |
Level Nuclear |
| 1645 |
Analytical Microwave |
| 1646 |
Analytical Density - Radiometric |
| 1647 |
Level Radiometric |
| 1648 |
Analytical Gas/Steam |
| 1649 |
Level Nucleonic |
| 1650 |
Analytical Blade Consistency |
| 1651 |
Analytical Rotary Consistency |
| 1652 |
Pressure Absolute/Differential |
| 1653 |
Positioner |
| 1654 |
Analytical Combustible Gas Detector |
| 1655 |
Analytical Point Infrared Gas Detector |
| 1656 |
Analytical Multi-Detector Monitor System |
| 1657 |
Valve Positioner/Electro-hydraulic |
| 1658 |
Valve Monitor |
| 1659 |
Enable on token-passing data link layer only |
| 1660 |
Enable on TDMA data link layer only |
| 1661 |
Enable on both TDMA and token-passing data link layer |
| 1662 |
WirelessHART Device |
| 1663 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 1664 |
Primary |
| 1665 |
Primary Analog Channel |
| 1666 |
Secondary |
| 1667 |
Secondary Analog Channel |
| 1668 |
Tertiary |
| 1669 |
Tertiary Analog Channel |
| 1670 |
Quaternary |
| 1671 |
Quaternary Analog Channel |
| 1672 |
Quinary |
| 1673 |
Quinary Analog Channel |
| 1674 |
Lock all |
| 1675 |
Trim not supported |
| 1676 |
Configuration cannot be changed |
| 1677 |
Locked by gateway |
| 1678 |
Analog Input Channel |
| 1679 |
Analog Output Channel |
| 1680 |
Simulation active |
| 1681 |
The device is in simulation mode and the level output is not representative of the process. |
| 1682 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 1683 |
The RAM memory check is invalid or maybe corrupt |
| 1684 |
A watchdog reset has been performed |
| 1685 |
A voltage condition is outside its allowable range |
| 1686 |
An internal or environmental condition is beyond acceptable limits. |
| 1687 |
A hardware problem not related to the sensor has been detected. |
| 1688 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 1689 |
Continuous |
| 1690 |
The Burst Message is published continuously at (worst case) the Minimum Update Period. |
| 1691 |
Window |
| 1692 |
The Burst Message is triggered when the source value deviates more than the specified trigger value |
| 1693 |
Rising |
| 1694 |
The Burst Message is triggered when source value Rises Above the specified trigger value. |
| 1695 |
Falling |
| 1696 |
The Burst Message is triggered when the source value Falls Below the specified trigger value. |
| 1697 |
On-change |
| 1698 |
The Burst Message is triggered when any value in the message changes. |
| 1699 |
Battery life |
| 1700 |
Percent range |
| 1701 |
Loop current |
| 1702 |
Primary variable |
| 1703 |
Secondary variable |
| 1704 |
Tertiary variable |
| 1705 |
Quaternary variable |
| 1706 |
Enable event notification on token-passing data link layer |
| 1707 |
Enable event notification on TDMA data link layer |
| 1708 |
Enable event notification on TDMA and token-passing data link layer |
| 1709 |
Configuration changed event pending |
| 1710 |
Device status event pending |
| 1711 |
More status available event pending |
| 1712 |
Enable single data point trending |
| 1713 |
Enable filtered trending |
| 1714 |
The sample is filtered using a time constant equal to one-third the trend sample period |
| 1715 |
Enable average trending |
| 1716 |
The value obtained by dividing the sum of all samples in the period by the total number of samples |
| 1717 |
Read receive time |
| 1718 |
Write date and time |
| 1719 |
Non-Volatile Clock |
| 1720 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 1721 |
Clock Uninitialized |
| 1722 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 1723 |
Line Power |
| 1724 |
Device is powered via a hardwired connection to a plant power source. |
| 1725 |
Battery Power |
| 1726 |
Device operates solely of its (internal) battery. |
| 1727 |
Recharg.B./Power Sc. |
| 1728 |
Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat). |
| 1729 |
Idle |
| 1730 |
Active search |
| 1731 |
Looking for neighbors. |
| 1732 |
Negotiating |
| 1733 |
Quarantined |
| 1734 |
Operational |
| 1735 |
Suspended |
| 1736 |
Deep sleep |
| 1737 |
Ultra-low power |
| 1738 |
Wireless Signal Found |
| 1739 |
Network packets have been recognized |
| 1740 |
Wireless Signal Identified |
| 1741 |
Wireless Time Synchronized |
| 1742 |
WirelessHart Signal Identified |
| 1743 |
Network Admission Requested |
| 1744 |
Set on transmission of first join request |
| 1745 |
Join Retrying |
| 1746 |
Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started. |
| 1747 |
Join Failed |
| 1748 |
Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search. |
| 1749 |
Network Security Clearance Granted |
| 1750 |
Network Manager Session Established |
| 1751 |
Network Joined |
| 1752 |
Network Joined. Normal superframe and links obtained. |
| 1753 |
Network Bandwidth Requested |
| 1754 |
Negotiating Network Properties. Gateway session obtained. |
| 1755 |
Join Complete |
| 1756 |
Normal operating mode. |
| 1757 |
No restrictions |
| 1758 |
SI Only |
| 1759 |
Restricted to SI Unit codes only |
| 1760 |
Open - accept all devices |
| 1761 |
Use Whitelist for access |
| 1762 |
Use Blacklist |
| 1763 |
Use Whitelist and Blacklist |
| 1764 |
Lockdown - disable join links |
| 1765 |
Process automation device |
| 1766 |
Discrete device |
| 1767 |
Hybrid:Process automation+discrete |
| 1768 |
I/O System |
| 1769 |
WirelessHART Process automation device |
| 1770 |
WirelessHART Discrete device |
| 1771 |
WirelessHART Process automation+discrete |
| 1772 |
WirelessHART Gateway |
| 1773 |
WirelessHART Access point |
| 1774 |
WirelessHART Process adapter |
| 1775 |
WirelessHART Discrete adapter |
| 1776 |
WirelessHART enabled handheld/portable maintenance tool |
| 1777 |
Don't attempt to join |
| 1778 |
Join now |
| 1779 |
Attempt to join immediately on powerup or reset |
| 1780 |
US |
| 1781 |
United States of America |
| 1782 |
JP |
| 1783 |
Japan |
| 1784 |
DE |
| 1785 |
Germany |
| 1786 |
FR |
| 1787 |
France |
| 1788 |
ES |
| 1789 |
Spain |
| 1790 |
RU |
| 1791 |
Russian Federation |
| 1792 |
CN |
| 1793 |
People's Republic of China |
| 1794 |
Nominal |
| 1795 |
Device Power Status is nominal |
| 1796 |
Device Power Status is low |
| 1797 |
Critically Low |
| 1798 |
Device Power Status is critically low |
| 1799 |
Recharging - Low |
| 1800 |
Recharging - High |
| 1801 |
Secondary Master |
| 1802 |
Primary Master |
| 1803 |
Device Profile |
| 1804 |
Time Set Option |
| 1805 |
Real Time Clock Flags |
| 1806 |
Country |
| 1807 |
Country of intended device installation |
| 1808 |
SI Unit Control |
| 1809 |
Indicates if device should only display SI unit codes |
| 1810 |
Burst Trigger Units |
| 1811 |
Burst Trigger Class |
| 1812 |
Wired HART Enabled |
| 1813 |
Enabled on Wired HART device connection only |
| 1814 |
Wireless HART Enabled |
| 1815 |
Enabled on WirelessHART device connection only |
| 1816 |
Both Wired and WirelessHart Enabled |
| 1817 |
Enabled on both Wired and WirelessHART connections |
| 1818 |
Burst Msg Trigger Mode |
| 1819 |
Event Status |
| 1820 |
Event Notification Control |
| 1821 |
Operate mode Mask |
| 1822 |
Not Defined |
| 1823 |
Power Source |
| 1824 |
Power source of the device |
| 1825 |
Wireless Mode |
| 1826 |
Join Status |
| 1827 |
The current location in the joining sequence of operations. |
| 1828 |
Network Access Mode |
| 1829 |
Join Mode |
| 1830 |
Power Status |
| 1831 |
Power status of the device |
| 1832 |
Master Mode |
| 1833 |
This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode. |
| 1834 |
Trend Units |
| 1835 |
Trend Device Variable Unit Code |
| 1836 |
Trend Classification |
| 1837 |
Trend Device Variable Classification |
| 1838 |
Trend Control |
| 1839 |
Device Status Mask |
| 1840 |
Ext dev status Mask |
| 1841 |
Device Diagnostic Status 0 Mask |
| 1842 |
Device Diagnostic Status 1 Mask |
| 1843 |
Device Diagnostic Status 2 Mask |
| 1844 |
Device Diagnostic Status 3 Mask |
| 1845 |
AO saturated Mask |
| 1846 |
AO fixed Mask |
| 1847 |
Latched Device Status |
| 1848 |
Latched Ext dev status |
| 1849 |
Latched Operate Mode |
| 1850 |
Latched Device Diagnostic Status 0 |
| 1851 |
Latched Device Diagnostic Status 1 |
| 1852 |
Latched Device Diagnostic Status 2 |
| 1853 |
Latched Device Diagnostic Status 3 |
| 1854 |
Latched AO saturated |
| 1855 |
Latched AO fixed |
| 1856 |
Wireless Module Device Type |
| 1857 |
Device type of the Wireless Radio |
| 1858 |
Wireless Module Manufacturer ID |
| 1859 |
Manufacturer of the Wireless Radio contained in this device |
| 1860 |
Subdevice Device Type |
| 1861 |
Device type of the subdevice attached to this system. |
| 1862 |
Subdevice Manufacturer Id |
| 1863 |
Manufacturer of the subdevice attached to this system. |
| 1864 |
Time Stamp |
| 1865 |
Relative time value on network |
| 1866 |
8u |
| 1867 |
Dynamic Variables Returned for Device Variables |
| 1868 |
Command Response Truncated |
| 1869 |
Configuration Change Counter Mismatch |
| 1870 |
Status bytes mismatch |
| 1871 |
8.3f |
| 1872 |
.3f |
| 1873 |
Update time adjusted |
| 1874 |
Invalid burst message |
| 1875 |
Invalid device variable classification |
| 1876 |
Invalid burst trigger mode selection code |
| 1877 |
Burst condition conflict |
| 1878 |
Update period increased |
| 1879 |
Insufficient bandwidth |
| 1880 |
Update period or debounce interval adjusted |
| 1881 |
Update times adjusted |
| 1882 |
Update rate uncertain |
| 1883 |
Not all events cleared |
| 1884 |
Device Variable |
| 1885 |
Total Burst Msgs |
| 1886 |
Total number of burst messages supported by this device |
| 1887 |
Number of Events Supported |
| 1888 |
Time First Unack Event Triggered |
| 1889 |
The time when the first unacknowledged event was triggered |
| 1890 |
Event Debounce Interval |
| 1891 |
Event Notification Retry Time |
| 1892 |
Max Update Time |
| 1893 |
Device Specific Status 0 Mask |
| 1894 |
Device Specific Status 1 Mask |
| 1895 |
Device Specific Status 2 Mask |
| 1896 |
Device Specific Status 3 Mask |
| 1897 |
Device Specific Status 4 Mask |
| 1898 |
Device Specific Status 5 Mask |
| 1899 |
Device Specific Status 14 Mask |
| 1900 |
Device Specific Status 15 Mask |
| 1901 |
Device Specific Status 16 Mask |
| 1902 |
Device Specific Status 17 Mask |
| 1903 |
Device Specific Status 18 Mask |
| 1904 |
Device Specific Status 19 Mask |
| 1905 |
Device Specific Status 20 Mask |
| 1906 |
Latched Device Specific Status 0 |
| 1907 |
Latched Device Specific Status 1 |
| 1908 |
Latched Device Specific Status 2 |
| 1909 |
Latched Device Specific Status 3 |
| 1910 |
Latched Device Specific Status 4 |
| 1911 |
Latched Device Specific Status 5 |
| 1912 |
Latched Device Specific Status 14 |
| 1913 |
Latched Device Specific Status 15 |
| 1914 |
Latched Device Specific Status 16 |
| 1915 |
Latched Device Specific Status 17 |
| 1916 |
Latched Device Specific Status 18 |
| 1917 |
Latched Device Specific Status 19 |
| 1918 |
Latched Device Specific Status 20 |
| 1919 |
Latched Cfg chng count |
| 1920 |
Update period for burst message |
| 1921 |
Maxium update period for burst message |
| 1922 |
Burst Command |
| 1923 |
Cmd 48: Read Additional Device Status |
| 1924 |
Read Additional Device - This command reads additional device status information |
| 1925 |
Burst Trigger Level |
| 1926 |
Event Number |
| 1927 |
Set Clock Time |
| 1928 |
Time to set the real time clock in the field device to, or time that the real-time clock was last set |
| 1929 |
Set Clock Date |
| 1930 |
Date to set the real-time clock in the field device to, or date that the real-time clock was last set |
| 1931 |
Current Time |
| 1932 |
Current Time based upon the real-time clock in the field device |
| 1933 |
Current Date |
| 1934 |
Current Date based upon the real-time clock in the field device |
| 1935 |
Burst Message Number |
| 1936 |
PV is: |
| 1937 |
PV is: %{primary_variable_code}
Are you sure to change the parameter ? |
| 1938 |
PV map was changed successfully. |
| 1939 |
SV is: |
| 1940 |
SV is: %{secondary_variable_code}
Are you sure to change the parameter ? |
| 1941 |
SV map was changed successfully. |
| 1942 |
TV is: |
| 1943 |
TV is: %{tertiary_variable_code}
Are you sure to change the parameter ? |
| 1944 |
TV map was changed successfully. |
| 1945 |
QV is: |
| 1946 |
QV is: %{quaternary_variable_code}
Are you sure to change the parameter ? |
| 1947 |
QV map was changed successfully. |
| 1948 |
Enter current password to enable to write for 10 minutes: |
| 1949 |
Released the write protection for 10 minutes. |
| 1950 |
If you wish to release completely, you have to change password to all of spaces. |
| 1951 |
Enter new password to change state of write protect: |
| 1952 |
Re-enter new password within 30 seconds: |
| 1953 |
Aborting method due to last error |
| 1954 |
Changed to new password. |
| 1955 |
It changed the state of protection related password. |
| 1956 |
Current date in device: %{current_date}
Current time in device: %{current_time}
Are you sure you to change the date and time ?
|
| 1957 |
NO;YES |
| 1958 |
Enter date (MM/DD/YYYY) |
| 1959 |
Enter time (hh:mm:ss) |
| 1960 |
Device returned a response of warning.
Please refer to the following. |
| 1961 |
Device returned a response of error.
Please refer to the following.
After that this operation will be aborted. |
| 1962 |
Are you sure to perform device reset ? |
| 1963 |
Exit;Execute |
| 1964 |
Device reset fail:response error |
| 1965 |
There is active status. Please refer to the followings. |
| 1966 |
All status are cleared. |
| 1967 |
Is it OK to reset the configuration changed flag ? |
| 1968 |
It was done to reset the configuration changed flag. |
| 1969 |
Are you sure to execute Autozero? |
| 1970 |
Not execute;Execute |
| 1971 |
The previous error was seen while trying to initiate auto zero. |
| 1972 |
Executing autozero...%{Autozero_progress}% |
| 1973 |
Autozero execute was aborted |
| 1974 |
Autozero passed for Calibrator |
| 1975 |
Autozero passed |
| 1976 |
Autozero failed |
| 1977 |
The previous error was seen while trying to abort Autozero. |
| 1978 |
Select squawk control: |
| 1979 |
Squawk Off. |
| 1980 |
Squawk in progress just for once. |
| 1981 |
Squawk in progress. |
| 1982 |
Is it OK to exit with Squawk Off ? |
| 1983 |
Select a Device Variable: |
| 1984 |
Value for simulate: (%{simulation_unit_for_edit})
|
| 1985 |
Data quality status for simulate:
|
| 1986 |
Limit status for simulate:
|
| 1987 |
Are you sure ?
Device Variable:%{deviceVariables_simulation}
Value:%{simulation_value_for_edit} (%{simulation_unit_for_edit})
Data quality status:%{simulation_data_quality_for_edit}
Limit status:%{simulation_limit_status_for_edit}
|
| 1988 |
Modify;OK |
| 1989 |
Read Backed:
Device Variable:%{deviceVariables_simulation}
Value:%{simulation_value_for_check} (%{simulation_unit_for_check})
Data quality:%{simulation_data_quality_for_check}
Limit status:%{simulation_limit_status_for_check}
|
| 1990 |
Exit Device variables simulation ? |
| 1991 |
Exit;Continue |
| 1992 |
Finish device variable simulation |
| 1993 |
device variable simulation was aborted |
| 1994 |
Select the status simulation mode: |
| 1995 |
Are you sure to change the status simulation mode ? |
| 1996 |
Status bit simulation was disabled. |
| 1997 |
Target bit to simulate: |
| 1998 |
Exit simulation;Exit (as maintaining simulation);Device Status;Status group 0;Status group 1;Status group 2;Status group 3;Status group 4;Status group 5;Ext dev status;Operate mode;Device Diagnostic Status 0;Device Diagnostic Status 1;AO saturated;I/O and Subdevice Status;WirelessHART Status;AO fixed;Status group 14;Status group 15;Status group 16;Status group 17;Status group 18;Status group 19;Status group 20; |
| 1999 |
Set bit to simulate: |
| 2000 |
Fld dev output 4mA equal to reference meter ? |
| 2001 |
Fld dev output 20mA equal to reference meter ? |
| 2002 |
Are you sure to clear D/A trim 1 ? |
| 2003 |
D/A trim 1 was cleared successfully. |
| 2004 |
Are you sure to clear D/A trim 2 ? |
| 2005 |
D/A trim 2 was cleared successfully. |
| 2006 |
WARN-Input value may be changed. |
| 2007 |
Connect reference input source. |
| 2008 |
It may take a long time to become stable input depending on the damping value. |
| 2009 |
Input 4.0 mA as the zero trim point for the reference input. |
| 2010 |
Measured input current is %[5.3f]{Analog_input_current} mA.
Wait for a second... |
| 2011 |
Measured input current is %[5.3f]{Analog_input_current} mA.
Has it become stable ? |
| 2012 |
Is it OK to enter the measured input value ?
Or, re-enter the value. |
| 2013 |
Wait for trimming... |
| 2014 |
Measured input current is %[5.3f]{Analog_input_current} mA.
Is it trimmed correctly ? |
| 2015 |
Input 20.0 mA as the gain trim point for the reference input. |
| 2016 |
Measured input current is %[6.3f]{Analog_input_current} mA.
Wait for a second... |
| 2017 |
Measured input current is %[6.3f]{Analog_input_current} mA.
Has it become stable ? |
| 2018 |
Measured input current is %[6.3f]{Analog_input_current} mA.
Is it trimmed correctly ? |
| 2019 |
Analog input trim was completed. |
| 2020 |
Are you sure to clear AI trim ? |
| 2021 |
AI trim was cleared successfully. |
| 2022 |
Are you sure to execute parameter backup? |
| 2023 |
The previous error was seen while trying to initiate parameter backup. |
| 2024 |
Executing parameter backup... |
| 2025 |
Checking backup result... |
| 2026 |
Parameter backup successed |
| 2027 |
Parameter backup failed |
| 2028 |
The previous error was seen while trying to abort parameter backup. |
| 2029 |
Parameter backup was aborted. |
| 2030 |
Are you sure to execute parameter restore? |
| 2031 |
The previous error was seen while trying to initiate parameter restore. |
| 2032 |
Executing parameter restore... |
| 2033 |
Checking restore result... |
| 2034 |
Parameter restore successed |
| 2035 |
Parameter restore failed |
| 2036 |
The previous error was seen while trying to abort parameter restore. |
| 2037 |
Parameter restore was aborted. |
| 2038 |
Current volume flow parameters
Volume flow unit: %{Volume_flow_unit}
Time unit: %{Time_unit}
Volume flow damping AO/frequency: %{Volume_flow_damping_AO_frequency}s
Volume flow damping pulse/total: %{Volume_flow_damping_pulse_total}s
Volume flow span: %{Volume_flow_span}%{Volume_flow_unit}%{Time_unit}
|
| 2039 |
Select the Volume flow unit |
| 2040 |
Select the Time unit |
| 2041 |
Enter the Volume flow damping AO/frequency |
| 2042 |
Enter the Volume flow damping pulse/total |
| 2043 |
Enter the Volume flow span |
| 2044 |
Parameters to send to the device:
Volume flow unit: %{Volume_flow_unit}
Time unit: %{Time_unit}
Volume flow damping AO/frequency: %{Volume_flow_damping_AO_frequency}s
Volume flow damping pulse/total: %{Volume_flow_damping_pulse_total}s
Volume flow span: %{Volume_flow_span}%{Volume_flow_unit}%{Time_unit}
|
| 2045 |
Are you sure to change the parameters ? |
| 2046 |
Device configuration changing. It will take a few seconds. |
| 2047 |
Volume flow settings were changed successfully. |
| 2048 |
Aborted. Volume flow settings were not changed. |
| 2049 |
Current pulse/status out 1 parameters
Pulse1 rate unit: %{Pulse_output_1_rate_unit}
Pulse1 rate value: %{Pulse_output_1_rate_value}%{Pulse_output_1_rate_unit}
Frequency1 at 0%: %{Frequency_out_1_at_0_per}Hz
Frequency1 at 100%: %{Frequency_out_1_at_100_per}Hz
|
| 2050 |
Select the pulse out 1 rate unit |
| 2051 |
Enter the pulse out 1 rate value |
| 2052 |
Enter the Frequency1 at 0% |
| 2053 |
Enter the Frequency1 at 100% |
| 2054 |
Parameters to send to the device:
Pulse1 rate unit: %{Pulse_output_1_rate_unit}
Pulse1 rate value: %{Pulse_output_1_rate_value}%{Pulse_output_1_rate_unit}
Frequency1 at 0%: %{Frequency_out_1_at_0_per}Hz
Frequency1 at 100%: %{Frequency_out_1_at_100_per}Hz
|
| 2055 |
Pulse/Status out 1 settings were changed successfully. |
| 2056 |
Aborted. Pulse/Status out 1 settings were not changed. |
| 2057 |
Current display select values
Display select1: %{Display_line_select_1}
Display select2: %{Display_line_select_2}
Display select3: %{Display_line_select_3}
|
| 2058 |
Select the display select 1 |
| 2059 |
Select the display select 2 |
| 2060 |
Select the display select 3 |
| 2061 |
Parameters to send to the device:
Display select1: %{Display_line_select_1}
Display select2: %{Display_line_select_2}
Display select3: %{Display_line_select_3}
|
| 2062 |
Display settings were changed successfully. |
| 2063 |
Aborted. Display settings were not changed. |
| 2064 |
WARN-Condensed status map will be reset to the default mapping values. |
| 2065 |
Are you sure to reset to the default mapping values ? |
| 2066 |
Condensed status map were reset to the default mapping values. |
| 2067 |
The previous error was seen while trying to initiate verification. |
| 2068 |
Are you sure to execute verification ? |
| 2069 |
Executing verification...%{VF_execution_progress}% |
| 2070 |
Checking VF result... |
| 2071 |
Verification passed
VF operation time: %{VF_Operation_time}
Magnetic circuit result: %{Magnetic_circuit_result}
Excitation circuit result: %{Excitation_circuit_result}
Calculation circuit result:%{Calculation_circuit_result}
VF device status result: %{Calculation_circuit_result_dev_sts}
Connection status result: %{Calculation_circuit_result_connect}
|
| 2072 |
Verification was aborted
Check the alarm |
| 2073 |
Verification failed
VF operation time: %{VF_Operation_time}
Magnetic circuit result: %{Magnetic_circuit_result}
Excitation circuit result: %{Excitation_circuit_result}
Calculation circuit result:%{Calculation_circuit_result}
VF device status result: %{Calculation_circuit_result_dev_sts}
Connection status result: %{Calculation_circuit_result_connect}
|
| 2074 |
The previous error was seen while trying to suspend Verification |
| 2075 |
Verification was aborted |
| 2076 |
Are you sure to perform Total1 reset/preset ? |
| 2077 |
Total1 reset successed |
| 2078 |
Total1 preset successed |
| 2079 |
Are you sure to perform Total2 reset/preset ? |
| 2080 |
Total2 reset successed |
| 2081 |
Total2 preset successed |
| 2082 |
Are you sure to perform Total3 reset/preset ? |
| 2083 |
Total3 reset successed |
| 2084 |
Total3 preset successed |
| 2085 |
Are you sure to execute Diagnosis ? |
| 2086 |
The previous error was seen while trying to initiate diagnosis. |
| 2087 |
Executing diagnosis...%{diag_exe_progress}% |
| 2088 |
Checking diagnosis result... |
| 2089 |
Diag execution was aborted |
| 2090 |
Electorode is normal |
| 2091 |
Electrode deterioration has occured |
| 2092 |
Diag execution was aborted
Check the alarm. |
| 2093 |
Connection is normal |
| 2094 |
Wire misconnection has occured |
| 2095 |
The previous error was seen while trying to suspend Diagnosis. |
| 2096 |
Select a target. |
| 2097 |
Easy Burst Message;Burst Message 1;Burst Message 2;Burst Message 3;ALL |
| 2098 |
Burst Message %[d]{target} is already OFF.
|
| 2099 |
Stop the Burst Message %[d]{target}. Are you sure ? |
| 2100 |
Stop all the Burst Messages. Are you sure ? |
| 2101 |
Easy Burst Message is already OFF.
|
| 2102 |
Stop the Easy Burst Message. Are you sure ? |
| 2103 |
Easy Burst is already ON.
You need turn OFF Easy Burst for the moment. Are you sure to turn OFF ?
|
| 2104 |
Abort;Turn-Off to continue |
| 2105 |
Detailed Burst Message is ON.
|
| 2106 |
Select a data that you want to get: |
| 2107 |
PV;Loop Current and Percent Range;PV,SV,TV,QV;Device Variable;Device Variable with Status;Additional Device Status |
| 2108 |
SLOT 0: |
| 2109 |
Device variable of SLOT 0 has to be besides "Not used". Try again.
|
| 2110 |
SLOT 1: |
| 2111 |
SLOT 2: |
| 2112 |
SLOT 3: |
| 2113 |
Are you sure ?
|
| 2114 |
Loop Current and Percent Range |
| 2115 |
PV,SV,TV,QV |
| 2116 |
Device Variable: |
| 2117 |
Device Variable with Status: |
| 2118 |
Additional Device Status |
| 2119 |
SLOT 0:%{burst_variable_slot_for_edit[0]}
SLOT 1:%{burst_variable_slot_for_edit[1]}
SLOT 2:%{burst_variable_slot_for_edit[2]}
SLOT 3:%{burst_variable_slot_for_edit[3]}
|
| 2120 |
|
| 2121 |
Burst Message 1;Burst Message 2;Burst Message 3 |
| 2122 |
Burst Message %[d]{bmn} is already OFF.
|
| 2123 |
Stop the Burst Message %[d]{bmn}. Are you sure ? |
| 2124 |
Easy Burst Message is ON.
|
| 2125 |
Burst Message %[d]{bmn} is already ON.
You need turn OFF Burst Message %[d]{bmn} for the moment. Are you sure to turn OFF ?
|
| 2126 |
SLOT 0 (Required) |
| 2127 |
;SLOT 1 |
| 2128 |
;SLOT 2 |
| 2129 |
;SLOT 3 |
| 2130 |
;SLOT 4 |
| 2131 |
;SLOT 5 |
| 2132 |
;SLOT 6 |
| 2133 |
;SLOT 7 |
| 2134 |
;Display |
| 2135 |
;Proceed to the next |
| 2136 |
;Abort |
| 2137 |
Select a number of SLOT or what to do :
|
| 2138 |
SLOT %{slot_no}: |
| 2139 |
All slots SLOT number %{slot_no} or later will be "Not used". Are you sure ?
|
| 2140 |
No(modify this SLOT);Yes |
| 2141 |
Device Variables :
|
| 2142 |
SLOT 0:%{burst_variable_slot_for_edit[0]}
|
| 2143 |
SLOT 1:%{burst_variable_slot_for_edit[1]}
|
| 2144 |
SLOT 2:%{burst_variable_slot_for_edit[2]}
|
| 2145 |
SLOT 3:%{burst_variable_slot_for_edit[3]}
|
| 2146 |
SLOT 4:%{burst_variable_slot_for_edit[4]}
|
| 2147 |
SLOT 5:%{burst_variable_slot_for_edit[5]}
|
| 2148 |
SLOT 6:%{burst_variable_slot_for_edit[6]}
|
| 2149 |
SLOT 7:%{burst_variable_slot_for_edit[7]}
|
| 2150 |
PV,SV,TV,QV; |
| 2151 |
Device Variable with Status |
| 2152 |
Setting Burst Message Period :
|
| 2153 |
Set - Update Period;Set - Maximum Update Period;Display;Proceed to next;Abort (Discard) |
| 2154 |
Update Period(in Seconds): |
| 2155 |
0.5;1;2;4;8;16;32;60-3600(Any Value) |
| 2156 |
Maximum Update Period(in Seconds): |
| 2157 |
Update Period : %{update_period_for_edit}
Maximum Update Period : %{max_update_period_for_edit}
|
| 2158 |
Update Period must be less than or equal to the Maximum Update Period.
Please correct either of parameters. |
| 2159 |
You have not yet inputted any timing parameters. (*)
|
| 2160 |
* Update Period : %{update_period_for_edit}
|
| 2161 |
Update Period : %{update_period_for_edit}
|
| 2162 |
* Maximum Update Period : %{max_update_period_for_edit}
|
| 2163 |
Maximum Update Period : %{max_update_period_for_edit}
|
| 2164 |
Do you apply these values and proceed the next? |
| 2165 |
NO:Return;YES:Proceed |
| 2166 |
Input Time(in Seconds from 60 to 3600): |
| 2167 |
ms_timval |
| 2168 |
Value to update:
Update Period : %{update_period_for_edit}
Maximum Update Period : %{max_update_period_for_edit}
|
| 2169 |
Select a trigger mode: |
| 2170 |
Trigger Level: (%{burst_trigger_units_for_edit}) |
| 2171 |
Event Notification is already OFF.
|
| 2172 |
Stop the Event Notification. Are you sure ? |
| 2173 |
Event Notification is already ON.
You need turn OFF Event Notification for the moment. Are you sure to turn OFF ?
|
| 2174 |
In order to enable the Event Notification, it is necessary to enable any Detailed Burst Messages. |
| 2175 |
All events have already acked. |
| 2176 |
Target latched outstanding event to ack:
Time of first: %{time_of_first_unack_event}
Config. Chng. Cntr: %{config_change_counter_latched_value}
|
| 2177 |
Are you sure to acknowledge the latched outstanding event ? |
| 2178 |
All events have acked. |
| 2179 |
Setting Event Notification Timing :
|
| 2180 |
Set - Event Notification Retry Time;Set - Maximum Update Time;Set - Event De-bounce Interval;Display;Proceed to next;Abort (Discard) |
| 2181 |
Event Notification Retry Time(in Seconds): |
| 2182 |
Maximum Update Time(in Seconds): |
| 2183 |
Event De-bounce Interval(in Seconds): |
| 2184 |
0.5;1;2;4;8;16;32;60-3600(Any Value);0(No De-bounce) |
| 2185 |
Event Notification Retry Time : %{event_notification_retry_time_event_for_edit}
Maximum Update Time : %{max_update_time_event_for_edit}
Event De-bounce Interval : %{event_debounce_interval_event_for_edit}
|
| 2186 |
The Retry Time must be less than or equal to the Maximum Update Time.
Please correct either of parameters. |
| 2187 |
* Event Notification Retry Time : %{event_notification_retry_time_event_for_edit}
|
| 2188 |
Event Notification Retry Time : %{event_notification_retry_time_event_for_edit}
|
| 2189 |
* Maximum Update Time : %{max_update_time_event_for_edit}
|
| 2190 |
Maximum Update Time : %{max_update_time_event_for_edit}
|
| 2191 |
* Event De-bounce Interval : %{event_debounce_interval_event_for_edit}
|
| 2192 |
Event De-bounce Interval : %{event_debounce_interval_event_for_edit}
|
| 2193 |
Value to update:
Event Notification Retry Time : %{event_notification_retry_time_event_for_edit}
Maximum Update Time : %{max_update_time_event_for_edit}
Event De-bounce Interval : %{event_debounce_interval_event_for_edit}
|
| 2194 |
Setting Event Notification Bit Mask :
|
| 2195 |
Set - Device Status Mask;Set - Device Specific Status 0 Mask;Set - Device Specific Status 1 Mask;Set - Device Specific Status 2 Mask;Set - Device Specific Status 3 Mask;Set - Device Specific Status 4 Mask;Set - Device Specific Status 5 Mask;Set - Device Specific Status 14 Mask;Set - Device Specific Status 15 Mask;Set - Device Specific Status 16 Mask;Set - Device Specific Status 17 Mask;Set - Device Specific Status 18 Mask;Set - Device Specific Status 19 Mask;Set - Device Specific Status 20 Mask;Set - Extended Device Status Mask;Set - Device Diagnostic Status 0 Mask;Set - Device Diagnostic Status 1 Mask;Set - Analog Channel Saturated 1 Mask;Set - Device Diagnostic Status 2 Mask;Set - Device Diagnostic Status 3 Mask;Set - Analog Channel Fixed 1 Mask;Display Masks1;Display Masks2;Proceed to the next;Abort (Discard) |
| 2196 |
Device Status: |
| 2197 |
Device Specific Status 0: |
| 2198 |
Device Specific Status 1: |
| 2199 |
Device Specific Status 2: |
| 2200 |
Device Specific Status 3: |
| 2201 |
Device Specific Status 4: |
| 2202 |
Device Specific Status 5: |
| 2203 |
Device Specific Status 14: |
| 2204 |
Device Specific Status 15: |
| 2205 |
Device Specific Status 16: |
| 2206 |
Device Specific Status 17: |
| 2207 |
Device Specific Status 18: |
| 2208 |
Device Specific Status 19: |
| 2209 |
Device Specific Status 20: |
| 2210 |
Extended Device Status: |
| 2211 |
Device Diagnostic Status 0: |
| 2212 |
Device Diagnostic Status 1: |
| 2213 |
Analog Channel Saturated 1: |
| 2214 |
Device Diagnostic Status 2: |
| 2215 |
Device Diagnostic Status 3: |
| 2216 |
Analog Channel Fixed 1: |
| 2217 |
Device Status Mask : %[02x]{device_status_mask_for_edit}
Device Specific Status 0 Mask : %[02x]{device_specific_status_0_mask_for_edit}
Device Specific Status 1 Mask : %[02x]{device_specific_status_1_mask_for_edit}
Device Specific Status 2 Mask : %[02x]{device_specific_status_2_mask_for_edit}
Device Specific Status 3 Mask : %[02x]{device_specific_status_3_mask_for_edit}
Device Specific Status 4 Mask : %[02x]{device_specific_status_4_mask_for_edit}
Device Specific Status 5 Mask : %[02x]{device_specific_status_5_mask_for_edit}
Device Specific Status 14 Mask : %[02x]{device_specific_status_14_mask_for_edit}
Device Specific Status 15 Mask : %[02x]{device_specific_status_15_mask_for_edit}
Device Specific Status 16 Mask : %[02x]{device_specific_status_16_mask_for_edit}
|
| 2218 |
Device Specific Status 17 Mask : %[02x]{device_specific_status_17_mask_for_edit}
Device Specific Status 18 Mask : %[02x]{device_specific_status_18_mask_for_edit}
Device Specific Status 19 Mask : %[02x]{device_specific_status_19_mask_for_edit}
Device Specific Status 20 Mask : %[02x]{device_specific_status_20_mask_for_edit}
Extended Device Status Mask : %[02x]{extended_device_status_mask_for_edit}
Device Diagnostic Status 0 Mask : %[02x]{standardized_status_0_mask_for_edit}
Device Diagnostic Status 1 Mask : %[02x]{standardized_status_1_mask_for_edit}
Analog Channel Saturated 1 Mask :%[02x]{analog_channel_saturated1_mask_for_edit}
Device Diagnostic Status 2 Mask : %[02x]{standardized_status_2_mask_for_edit}
Device Diagnostic Status 3 Mask : %[02x]{standardized_status_3_mask_for_edit}
Analog Channel Fixed 1 Mask :%[02x]{analog_channel_fixed1_mask_for_edit}
|