Device dictionary

Loading…

Reference ID	String
0	TP2000 Series
1	Toshniwal Industries Private Limited.
2	.4f
3	11.4f
4	Sensor info
5
6	Sensor mode
7	The sensor mode of transmitter
8	DP
9	Differential pressure sensor
10	LT
11	Differential pressure level sensor
12	DR
13	Differential pressure remote sensor
14	GP
15	Gauge pressure sensor
16	GRN
17	Gauge pressure sensor direct pack
18	GRS
19	Gauge pressure remote sensor
20	AP
21	Absolute pressure sensor
22	ARN
23	Absolute pressure sensor direct pack
24	ARS
25	Absolute pressure remote sensor
26	Sensor range
27	The sensor range of transmitter
28	1 KPa
29	Upper sensor limit is 1 kpa
30	6 KPa
31	Upper sensor limit is 6 kpa
32	40 KPa
33	Upper sensor limit is 40 kpa
34	250 KPa
35	Upper sensor limit is 250 kpa
36	3000 KPa
37	Upper sensor limit is 3000 kpa
38	2000 KPa
39	Upper sensor limit is 2000 kpa
40	10 MPa
41	Upper sensor limit is 10 MPa
42	21 MPa
43	Upper sensor limit is 21 MPa
44	40 MPa
45	Upper sensor limit is 40 MPa
46	60 MPa
47	Upper sensor limit is 60 MPa
48	70 MPa
49	Upper sensor limit is 70 MPa
50	4000 KPa
51	Upper sensor limit is 4000 kpa
52	LCD display
53	Local LCD display code
54	PV
55	Primary variable display
56	Percent
57	Percent range display
58	Current
59	Loop current display
60	OUT
61	Simulate from loop current display
62	Key zero
63	Off
64	Local key button status is off
65	On
66	Local key button status is on
67	Key span
68	Keys status
69	UnLocked
70	Local buttons is unlocked
71	Locked
72	Local buttons is locked
73	OUT unit
74	The OUT value could be set to any meaning
75	OUT value
76	OUT LRV
77	OUT URV
78	Signal cut
79	Small signal cut down percent
80	.2f
81	6.2f
82	Electronic s/n
83	Electronic board serial number
84	7d
85	Low alarm
86	Low alarm current value
87	.3f
88	6.3f
89	High alarm
90	High alarm current value
91	setting not accepted
92	Low saturation
93	Low saturation current value
94	High saturation
95	High saturation current value
96	Low alert value
97	Low alert pressure value when saturated
98	High alert value
99	High alert pressure value when saturated
100	setting_not_accepted
101	Max pressure
102	The maximum overrange value recorded
103	Min pressure
104	The minimum overrange value recorded
105	Isolator material
106	The isolator material used
107	None
108	316L
109	316L Stainless Steel
110	Hast-C
111	Hastelloy C
112	316L-Gold
113	Gold Plated on 316L
114	316L-FEP
115	FEP Plated on 316L
116	Tantalum
117	Monel
118	Other
119	Other Items
120	Fill fluid
121	The fill fluid used
122	Si-oil
123	Silicone Oil
124	F-oil
125	Fluorinated Oil
126	Pl-oil
127	Plant Oil
128	Process connection
129	The process connection way used
130	1
131	1/2NPT female thread
132	2
133	1/2NPT male thread(Include 1/4 NPT internal)
134	3
135	M20*1.5 male thread
136	4
137	G1/2 male thread
138	5
139	Vacuum interface
140	6
141	1/4NPT male thread
142	7
143	1/4NPT female thread
144	8
145	G1/4 male thread
146	9
147	High temperature dissipation interface, 1/2NPT female thread
148	L
149	G1 thread pulp interface sealing device
150	M
151	M44*1.25 thread pulp interface sealing device
152	S
153	Ф25.8 insertion pulp interface sealing device
154	R
155	Remote seal for GP/AP
156	N
157	7/16UNF and 1/4NPT female thread, No relief valve
158	B
159	7/16UNF and 1/4NPT female thread, Relief valves at the end of flanges
160	U
161	7/16UNF and 1/4NPT female thread, Relief valves at the upper part of the flange side
162	D
163	7/16UNF and 1/4NPT female thread, Relief valves at the lower part of the flange side
164	V
165	Vertical mounting flange,7/16UNF and 1/4NPT female thread, Relief valves at the upper part of the flange side
166	LN
167	Level, low side:7/16UNF and 1/4NPT female thread, No relief valve
168	LB
169	Level, low side:7/16UNF and 1/4NPT female thread, Relief valves at the end of flanges
170	LU
171	Level, low side:7/16UNF and 1/4NPT female thread, Relief valves at the upper part of the flange side
172	LD
173	Level, low side:7/16UNF and 1/4NPT female thread, Relief valves at lower part of the flange side
174	RN
175	Remote, low side:7/16UNF and 1/4NPT female thread, No relief valve
176	RB
177	Remote, low side:7/16UNF and 1/4NPT female thread, Relief valves at the end of flanges
178	RU
179	Remote, low side:7/16UNF and 1/4NPT female thread, Relief valves at the upper part of the flange side
180	RD
181	Remote, low side:7/16UNF and 1/4NPT female thread, Relief valves at the lower part of the flange side
182	RR
183	Remote, Double flange
184	Process Co.Ma.
185	Process connection material used
186	O-ring material
187	O-ring material used
188	NBR
189	Nitrile Rubber
190	FKM
191	Viton
192	PTFE
193	Teflon
194	Remote mode
195	The sensor remote mode used
196	None
197	Level flange, No capillary high-pressure side
198	RH
199	Capillary high-pressure side(DP)
200	RH/RL
201	Capillary both high/low-pressure side(DP)
202	TH
203	Capillary high-pressure side (DP thread)
204	TH/TL
205	Capillary both high/low- pressure side (DP thread)
206	Direct installation, No capillary(GP/AP)
207	RS
208	Capillary(GP/AP)
209	UN
210	Direct installation, No capillary (GP/AP with internal diaphragm)
211	US
212	Capillary (GP/AP with internal diaphragm)
213	TS
214	Capillary (GP/AP thread)
215	PS
216	Capillary (GP/AP high-temp melt)
217	Seal type
218	Remote seal type used
219	Type D
220	Type D, DN2526
221	Type E
222	Type E, DN2526
223	Type RF
224	Type RF, ANSI B16.5
225	Seal diaphgram Ma.
226	Remote seal diaphgram material used
227	Seal fill fluid
228	Remote seal fill fluid used
229	Si-oil(H)
230	High-temp Silicone Oil
231	Si-oil(UH)
232	Ultra High-temperature Silicone Oil
233	Oil(UL)
234	Ultra Low-temperature Filling Oil
235	Oil(UH)
236	Ultra High-temperature Filling Oil
237	Get 0%
238	Set the value as pv lower range
239	Get 100%
240	Set the value as pv upper range
241	Upper sensor trim
242	Upper sensor range trim
243	Lower sensor trim
244	Lower sensor range trim
245	mH2O
246	Meters of Water at 68 Degrees Fahrenheit
247	Pres Dev fmly
248	Pres Class
249	Pres PDQ
250	Pres LS
251	Pres Fmly stat
252	.1f
253	4.1f
254	Pressure Update Period
255	Pres Lower trim
256	Pres Upper trim
257	Pres Trim support
258	Pres Min lower trim
259	Pres Max lower trim
260	Pres Min upper trim
261	Pres Max upper trim
262	Pres Min trim diff
263	Simulate
264	Update Period
265	Snsr s/n(detail)
266	Sensor serial number in detail
267	Snsr temp unit
268	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
269	Temp Class
270	Temp PDQ
271	Temp LS
272	Temp Dev Stat
273	Temp USL
274	Temp LSL
275	Temp min span
276	8.3f
277	Temp Update Period
278	Temp snsr s/n
279	Secondary Variable - Temperature Reference
280	Pressure
281	Temperature
282	Device settings
283	Diagnostics
284	Maintenance
285	Offline
286	Operate
287	Quick setup
288	Rerange
289	Max trim percent(%FS)
290	%
291	Sensor range trim
292	Sensor trim points
293	Alarm/Saturation
294	Scaled output
295	General
296	Serial number
297	Module info
298	Remote seal info
299	Security
300	Buttons status
301	Press record
302	ﾚﾝｼﾞ範囲(out)
303	PV Analog Channel Saturated
304	PV Analog Channel Fixed
305	Wireless
306	WirelessHART Device
307	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
308	Primary
309	Primary Analog Channel
310	Secondary
311	Secondary Analog Channel
312	Tertiary
313	Tertiary Analog Channel
314	Quaternary
315	Quaternary Analog Channel
316	Quinary
317	Quinary Analog Channel
318	Critical Power Failure
319	Lock all
320	Trim not supported
321	Configuration cannot be changed
322	Locked by gateway
323	Analog Input Channel
324	Analog Output Channel
325	Secondary Analog Channel Saturated
326	Tertiary Analog Channel Saturated
327	Quaternary Analog Channel Saturated
328	Quinary Analog Channel Saturated
329	Secondary Analog Channel Fixed
330	Tertiary Analog Channel Fixed
331	Quaternary Analog Channel Fixed
332	Quinary Analog Channel Fixed
333	Simulation active
334	The device is in simulation mode and the level output is not representative of the process.
335	Non-Volatile memory failure
336	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
337	Volatile memory error
338	The RAM memory check is invalid or maybe corrupt
339	Watchdog reset executed
340	A watchdog reset has been performed
341	Voltage conditions out of range
342	A voltage condition is outside its allowable range
343	Environmental conditions out of range
344	An internal or environmental condition is beyond acceptable limits.
345	Electronic failure
346	A hardware problem not related to the sensor has been detected.
347	Subdevice list changed
348	Duplicate master detected
349	Capacity Denied
350	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
351	Bandwidth allocation pending
352	Block transfer pending
353	Battery life
354	Percent range
355	Loop current
356	Primary variable
357	Secondary variable
358	Tertiary variable
359	Quaternary variable
360	Read receive time
361	Write date and time
362	Non-Volatile Clock
363	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
364	Clock Uninitialized
365	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
366	No restrictions
367	SI Only
368	Restricted to SI Unit codes only
369	Process automation device
370	Discrete device
371	Hybrid:Process automation+discrete
372	I/O System
373	WirelessHART Process automation device
374	WirelessHART Discrete device
375	WirelessHART Process automation+discrete
376	WirelessHART Gateway
377	WirelessHART Access point
378	WirelessHART Process adapter
379	WirelessHART Discrete adapter
380	WirelessHART enabled handheld/portable maintenance tool
381	Device Profile
382	United States of America
383	JP
384	Japan
385	DE
386	Germany
387	FR
388	France
389	ES
390	Spain
391	Russian Federation
392	CN
393	People's Republic of China
394	Secondary Master
395	Primary Master
396	Device Diagnostic Status 0
397	Device Diagnostic Status 1
398	I/O and Subdevice Status
399	WirelessHART Status
400	Time Set Option
401	Real Time Clock Flags
402	Country
403	Country of intended device installation
404	SI Unit Control
405	Indicates if device should only display SI unit codes
406	Time Stamp
407	Relative time value on network
408	8u
409	Dynamic Variables Returned for Device Variables
410	Command Response Truncated
411	Configuration Change Counter Mismatch
412	Status bytes mismatch
413	Device Variable
414	Variable to trim
415	4mA;Exit
416	20mA;Exit
417	Please connect standard pressure source
418	The upper sensor limit is %[11.4f,L]{pressureUSL} %[U]{pressureUSL}; The max trim percent is 20 %FS; The last upper trim point is %[11.4f,L]{trim_point} %[U]{pressureUpperTrimPoint}; The process value is %[11.4f,D]{pressureValue} %[U]{pressureValue}; Please wait for the process value to be stable before operation.
419	The lower sensor limit is %[11.4f,L]{pressureLSL} %[U]{pressureLSL}; The max trim percent is 20 %FS; The last lower trim point is %[11.4f,L]{trim_point} %[U]{pressureLowerTrimPoint}; The process value is %[11.4f,D]{pressureValue} %[U]{pressureValue}; Please wait for the process value to be stable before operation!
420	現在のﾄﾘﾑﾎﾟｲﾝﾄ: %[11.4f,L]{lower_trim_point}%[U]{pressureLowerTrimPoint} 及び %[11.4f,L]{upper_trim_point} %[U]{pressureUpperTrimPoint}. です。ﾎﾟｲﾝﾄをﾘｾｯﾄしますか?
Reference ID	String