Device dictionary

Loading…

Reference ID	String
0	9701/03 Mass flo
1	Date- Gregorian calendar date, entered as mm/dd/yy, that is stored in the Field Device. This date can be used by the user in any way. There is no specific recommended use.
2	No
3	4.1f
4	RTD failure
5	Temperature out of range
6	Mass flow out of range
7	Volume flow out of range
8	Analog output saturated
9	Data loss possible
10	Analog output fixed
11	Raw flow overflow
12	Raw electronic zero overflow
13	Auto zero failure
14	Frequency output saturated
15	Frequency output fixed
16	Flo unit
17	Flo
18	.1f
19	.2f
20	.3f
21	.4f
22	.5f
23	The flow rate below which the frequency/pulse output indicates zero flow.
24	Flo cutoff
25	mA
26	Flo anlog valu
27	4.2f
28	%
29	Flo % rnge
30	Determines whether the Event is activated when it goes above (High) or below (Low) the setpoint.
31	Alarm select
32	Flo URV
33	Flo LRV
34	Sec
35	7d
36	Flo URL
37	8.2f
38	Flo LRL
39	Flo min span
40	Totl unit
41	Totl
42	QV
43	A control that enables the user to determine whether the frequency/pulse output and totalizers will indicate forward, reverse, or bi-directional flow.
44	The number of cycles, in Hertz, that equal a proportional flow rate represented by the frequency/pulse output.
45	Hz
46	The flow rate that equals a set frequency if the frequency output represents mass or volume flow; or the mass or volume total that equals a set number of pulses if the frequency output represents mass or volume total.
47	6.2f
48	A programmable high limit on density, which enables the transmitter to indicate slug flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed slug flow limits.
49	g/cc
50	Slug high limit
51	5.4f
52	A programmable low limit on density, which enables the transmitter to indicate slug flow (extremes in fluid density caused by slugs of gas or accumulation of solids in a liquid flow stream) if fluid density goes outside programmed slug flow limits.
53	Slug low limit
54	A 10-character factor that describes the sensitivity of the sensor to mass flow. The first 6 characters are the flow rate, in grams/second, per microsecond of time shift between velocity signals from the sensor. The 2nd four characters are the flow temperature coefficient.
55	FlowCal
56	A value (in Hertz) that will be indicated on the frequency output for the purpose of a loop test.
57	The frequency, in Hertz, presently being indicated on the frequency output.
58	Pres freq
59	6.1f
60	Allows the user to Reset all totalizers. NOTE - Inventory totals are NOT reset.
61	14 characters describing the sensitivity of the sensor to density.
62	A value, in microseconds, representing the phase shift between velocity signals from the sensor when measuring zero flow.
63	uSec
64	Zero value
65	5.3f
66	Units for zero offset - always microseconds.
67	Zero units
68	1d
69	Analog range vals
70	Freq scaling
71	View fld dev vars
72	View output vars
73	Test/Status
74	Charize sensor
75	Config outputs
76	View SV
77	View TV
78	View QV
79	Flow
80	Density
81	Analog output
82	Frequency output
83	Device info
84	Fld dev vars
85	Outputs
86	Write variables
87	Process Variables
88	Device
89	Diagnostic
90	Perform Cal
91	Please refer to manual for complete calibration instructions.
92	Fix Analog Output
93	Outputs a user-programmed frequency to the frequency output.
94	Trim Analog Output
95	Instructs transmitter to perform internal self test.
96	Reset totalizer
97	Resets internal totalizers.
98	View status
99	Reports any currently active device status information.
100	Exits fixed mode and returns the frequency output to its active state.
101	Aborts Auto Zero operation and continues to use previous zero offset value.
102	Total
103	Present Frequency
104	FMU860
105	DT
106	DVC
107	FCX
108	AS800
109	340T
110	340C
111	344
112	Siemens Micro K
113	SITRANS L
114	SIPAN PH
115	SITRANS P
116	75SMT
117	UNIDELTA
118	8320
119	SX5100
120	TSV175
121	DMU
122	3780
123	BM70
124	8u
125	WARN-Loop should be removed from automatic control
126	Flow must be zero Perform calibration?
127	A problem was detected
128	Abort;Fix and Retry
129	Calibration in Progress Zero: %0
130	Auto Zero Complete Zero: %0
131	NOTE-Loop may be returned to automatic control
132	Choose analog output level
133	4 mA;20 mA;Other;End
134	Output value:
135	userEntry
136	Aborting due to field device error
137	Analog Output is fixed at %0
138	Choose frequency output level
139	1 kHz;Other;End
140	Output
141	Frequency output is fixed at %0 Hz
142	Connect reference meter
143	About to set analog output to 4.0 mA
144	Enter meter value
145	Is fld dev 4.00 mA output equal to reference meter?
146	Yes;No
147	About to set analog output to 20.0 mA
148	Is fld dev 20.00 mA output equal to reference meter?
149	Selftest complete
150	Transmitter status complete
151	Transmitter status OK
152	Returning fld dev to original output
153	NOTE-Variables which use this as the units code will be in the previous units until this value is sent to the device
Reference ID	String