Device dictionary

Loading…

Reference ID	String
0	Metso Automation
1	SMARTPULP
2	Field device iden- tification in multidrop installations. Refer operation manual HART address
3	Measurement
4	Configuration
5	Detailed config
6	Device Info
7	Calibration
8	Diagnostics
9	Range values
10	New recipe
11	Recipe 1
12	Recipe 2
13	Recipe 3
14	Recipe 4
15	Recipe 5
16	Recipe 6
17	Recipe 7
18	Recipe 8
19	Sampling
20	Special grade
21	Tempr calibrations
22	Upload variables
23	AO
24	Analog output current
25	.2f
26	consistency units code
27	PV
28	Measured pulp consistency value
29	%Cs
30	cons range units
31	UppRnge
32	Consistency value corresponding 20mA current
33	LowRnge
34	Consistency value corresponding 4mA current
35	Damping
36	Damping time 1...60s used in consistency measurement
37	Alarm current
38	Fail safe protection either 22.5 mA or 3.7 mA
39	3.7 mA
40	22.5 mA
41	transfer function code
42	% of range
43	Consistency value as percentage (0-100%) of the measurement range ie. LRV-URV
44	.1f
45	force unit
46	Shear F.
47	Measured shear force
48	.0f
49	N
50	Active recipe
51	Number of the recipe currently in use Recipe 0 means that device uses digital inputs to select recipe
52	Sensor s/n
53	Sensor serial number
54	cons sensor units
55	USL
56	Highest recommended consistency for Upper Range Value
57	LSL
58	Lowest recommended consistency for Lower Range Value
59	Min span
60	Minimum difference between Lower range value and Upper range value
61	Sensor
62	Temperature of internal force sensor
63	sensor temperature units code
64	Process
65	Temperature of process
66	process temperature units
67	Housing
68	Temperature of electronics and housing
69	housing temperature code
70	Pulp
71	Fillers
72	P1
73	P2
74	Pulp type for recipe 1
75	HWU
76	Hardwood chemical unbleached pulp
77	HWB
78	Hardwood chemical bleached pulp
79	SWU
80	Softwood chemical unbleached pulp
81	SWB
82	Softwood chemical bleached pulp
83	GW
84	Groundwood mechanical pulp
85	TMPL
86	Thermo-mechanical pulp, freeness < 200ml
87	TMPH
88	Thermo-mechanical pulp, freeness > 200ml
89	RMPL
90	Refiner mechanical pulp, freeness < 200ml
91	RMPH
92	Refiner mechanical pulp, freeness > 200ml
93	CTMP
94	Chemi.mechanical pulp
95	RCFU
96	Recycled fibers non-screened
97	RCFS
98	Recycled fibers screened
99	ROCCU
100	Recycled old corrugated cardboard unscreened
101	ROCCS
102	Recycled old corrugated cardboard screened
103	ULIN
104	Unlinearized curve 0...30N = 0...100%
105	Pulp type for recipe 2
106	Pulp type for recipe 3
107	Pulp type for recipe 4
108	Pulp type for recipe 5
109	Pulp type for recipe 6
110	Pulp type for recipe 7
111	Pulp type for recipe 8
112	Fillers % for recipe 1
113	Average fillers content for recipe 1
114	Fillers % for recipe 2
115	Average fillers content for recipe 2
116	Fillers % for recipe 3
117	Average fillers content for recipe 3
118	Fillers % for recipe 4
119	Average fillers content for recipe 4
120	Fillers % for recipe 5
121	Average fillers content for recipe 5
122	Fillers % for recipe 6
123	Average fillers content for recipe 6
124	Fillers % for recipe 7
125	Average fillers content for recipe 7
126	Fillers % for recipe 8
127	Average fillers content for recipe 8
128	P1 for recipe 1
129	Linearization slope Lower limit is 0.1 Upper limit is 10.0 Do not exceed !
130	.3f
131	P1 for recipe 2
132	P1 for recipe 3
133	P1 for recipe 4
134	P1 for recipe 5
135	P1 for recipe 6
136	P1 for recipe 7
137	Linearization slope Lower limit is 0.1 Upper limit is 10.0 Do not exceed !
138	P1 for recipe 8
139	P2 for recipe 1
140	Linearization offset Lower limit is -10.0 Upper limit is 10.0 Do not exceed !
141	P2 for recipe 2
142	P2 for recipe 3
143	P2 for recipe 4
144	P2 for recipe 5
145	P2 for recipe 6
146	P2 for recipe 7
147	P2 for recipe 8
148	#1
149	#2
150	#3
151	#4
152	#5
153	#6
154	#7
155	#8
156	#9
157	#10
158	#11
159	#12
160	#13
161	#14
162	#15
163	#16
164	Offset
165	Point 1 consistency %Cs
166	Special grade point 1 consistency value
167	Point 2 consistency %Cs
168	Special grade point 2 consistency value
169	Point 3 consistency %Cs
170	Special grade point 3 consistency value
171	Point 4 consistency %Cs
172	Special grade point 4 consistency value
173	Point 5 consistency %Cs
174	Special grade point 5 consistency value
175	Point 6 consistency %Cs
176	Special grade point 6 consistency value
177	Point 7 consistency %Cs
178	Special grade point 7 consistency value
179	Point 8 consistency %Cs
180	Special grade point 8 consistency value
181	Point 9 consistency %Cs
182	Special grade point 9 consistency value
183	Point 10 consistency %Cs
184	Special grade point 10 consistency value
185	Point 11 consistency %Cs
186	Special grade point 11 consistency value
187	Point 12 consistency %Cs
188	Special grade point 12 consistency value
189	Point 13 consistency %Cs
190	Special grade point 13 consistency value
191	Point 14 consistency %Cs
192	Special grade point 14 consistency value
193	Point 15 consistency %Cs
194	Special grade point 15 consistency value
195	Point 16 consistency %Cs
196	Special grade point 16 consistency value
197	Point 1 offset %Cs
198	Special grade point 1 offset value
199	Point 2 offset %Cs
200	Special grade point 2 offset value
201	Point 3 offset %Cs
202	Special grade point 3 offset value
203	Point 4 offset %Cs
204	Special grade point 4 offset value
205	Point 5 offset %Cs
206	Special grade point 5 offset value
207	Point 6 offset %Cs
208	Special grade point 6 offset value
209	Point 7 offset %Cs
210	Special grade point 7 offset value
211	Point 8 offset %Cs
212	Special grade point 8 offset value
213	Point 9 offset %Cs
214	Special grade point 9 offset value
215	Point 10 offset %Cs
216	Special grade point 10 offset value
217	Point 11 offset %Cs
218	Special grade point 11 offset value
219	Point 12 offset %Cs
220	Special grade point 12 offset value
221	Point 13 offset %Cs
222	Special grade point 13 offset value
223	Point 14 offset %Cs
224	Special grade point 14 offset value
225	Point 15 offset %Cs
226	Special grade point 15 offset value
227	Point 16 offset %Cs
228	Special grade point 16 offset value
229	average
230	deviation
231	shear force
232	Mounting
233	Select Field device mounting orientation
234	VU
235	Vertical pipe. Transmitter upwards
236	HS
237	Horizontal pipe. Transmitter on the side of the pipe
238	HT
239	Horizontal pipe. Transmitter at the top of the pipe
240	Blade type
241	Refer operation manual for applications
242	GL
243	HL
244	JL
245	LL
246	LS
247	RL
248	UL
249	WS
250	Blade material
251	Construction and wetted materials of the transmitter
252	AISI 316 L
253	HASTELLOY C276
254	TITANIUM
255	Device code
256	Device specific selection code
257	Device status
258	Error flag bits read from Field Device showing device status OFF means OK ON means alarm
259	Tx/Rx error
260	Error in Serial Communication Interface
261	AD conv error
262	Analog to digital converter error
263	Err in HART msg
264	Error in HART message
265	Config error
266	Configuration data not valid
267	Calibr error
268	Calibration data not valid
269	Sensor over range
270	Force sensor over range
271	ST over range
272	Sensor temperature over range
273	PT over range
274	Process temperature over range
275	HT over range
276	Housing temperature over range
277	sampling status
278	correct temperature value
279	Sample1
280	Laboratory measured consistency percentage value for sample 1
281	Sample2
282	Laboratory measured consistency percentage value for sample 2
283	Filler%
284	Laboratory measured fillers percentage value for samples 1 and 2
285	lab recipe number
286	temperature channel
287	Sensor tempr
288	Process tempr
289	Housing tempr
290	usage of samples
291	grade index
292	sample number
293	recipe index
294	Send correct value to the sensor temperature
295	Send correct value to the process temperature
296	Send correct value to the housing temperature
297	Start sample 1
298	Start calculating sample 1 average consistency, standard deviation and force value
299	Start sample 2
300	Start calculating sample 2 average consistency, standard deviation and force value
301	Lab results
302	Calibrates selected recipe using laboratory results. Use first sample = 1-point calibration using first sample. Use second sample = 1-point calibration using second sample Use both samples = 2-point calibration using both samples
303	SUCCESS
304	INVALID SELECTION
305	INVALID RECIPE
306	PULP NOT ALLOWED FOR THIS BLADE
307	RECIPE NOT CALIBRATED
308	SUCCES
309	INVALID SAMPLE NUMBER
310	SAMPLE NOT TAKEN
311	CALIBRATION SUSPICIOUS
312	CALIBRATION ERROR
313	CORRECTION TOO LARGE
314	INVALID INDEX
315	FMU860
316	DT
317	DVC
318	FCX
319	AS800
320	340T
321	340C
322	344
323	Siemens Micro K
324	SITRANS L
325	SIPAN PH
326	SITRANS P
327	75SMT
328	UNIDELTA
329	8320
330	SX5100
331	TSV175
332	DMU
333	3780
334	BM70
335	8u
336	Give correct value for sensor temperature in %{0}
337	- WARNING - Pressing 'OK' will change device output. Put loop in manual.
338	- WARNING - Return control loop to automatic control
339	Give correct value for process temperature in %{0}
340	- WARNING - Pressing 'OK' will change device output. Put loop in manual.
341	- WARNING - Return control loop to automatic control
342	Give correct value for housing temperature in %{0}
343	- WARNING - Pressing 'OK' will change device output. Put loop in manual.
344	- WARNING - Return control loop to automatic control
345	Press OK to stop sample 1
346	WARNING Sample Deviation High
347	Sampling results of sample 1: Average %{0}%Cs Deviation %{1}%Cs Shear force %{2}g
348	Press OK to stop sample 2
349	Sampling results of sample 2: Average %{0}%Cs Deviation %{1}%Cs Shear force %{2}g
350	Enter recipe to calibrate
351	recipe
352	Recipe number must be 1 - 8
353	Usage of samples
354	Use first sample;Use second sample;Use both samples
355	Enter filler content %
356	filler
357	Filler content must be 0 - 75%
358	Enter laboratory consistency for sample 1
359	cons1
360	Consistency must be 0 - 50%Cs
361	Enter laboratory consistency for sample 2
362	cons2
363	Consistency must be 0 - 50%Cs
364	- WARNING - Pressing 'OK' will change device output. Put loop in manual.
365	- WARNING - Return control loop to automatic control
Reference ID	String