| 0 |
UltimaXL/XT |
| 1 |
MSA |
| 2 |
PV Out of Limit |
| 3 |
HELP - Bit 0 |
| 4 |
Non PV- Out of Limit |
| 5 |
HELP - Bit 1 |
| 6 |
PV Analog Out - Saturated |
| 7 |
HELP - Bit 2 |
| 8 |
PV Analog Out - Fixed |
| 9 |
HELP - Bit 3 |
| 10 |
More Staus Available |
| 11 |
HELP - Bit 4 |
| 12 |
Cold Start |
| 13 |
HELP - Bit 5 |
| 14 |
Config Changed |
| 15 |
HELP - Bit 6 |
| 16 |
Device Malfunction |
| 17 |
HELP - Bit 7 |
| 18 |
Configuration Reset |
| 19 |
Main ram fault |
| 20 |
Main flash fault |
| 21 |
EEprom write error |
| 22 |
Incompatible sensor |
| 23 |
Sensor quick underrange |
| 24 |
Sensor underrange |
| 25 |
Calibration fault |
| 26 |
Sensor Missing |
| 27 |
No sensor detected |
| 28 |
Sensor Overrange |
| 29 |
Sensor reading overrange! |
| 30 |
Sensor in Overrange Loc |
| 31 |
Combustible sensor in overrange lock! |
| 32 |
Sensor Parameter Fault |
| 33 |
Sensor Warm up |
| 34 |
Sensor Warming up |
| 35 |
Sensor Config Reset |
| 36 |
Sensor Configuration has been reset |
| 37 |
Sensor Power Fault |
| 38 |
Sensor Power Fault detected |
| 39 |
5V Power Fault |
| 40 |
Main board 5V Power Fault detected |
| 41 |
Zero Countdn |
| 42 |
Cal- 30sec Zero Countdn |
| 43 |
Apply Zero Gas |
| 44 |
Cal- Waiting for Zero Gas |
| 45 |
Span Countdn |
| 46 |
Cal- 30s Span Countdn |
| 47 |
Apply Span Gas |
| 48 |
Cal- Waiting for Span Gas |
| 49 |
Cal Aborted |
| 50 |
Calibration sequence aborted |
| 51 |
Zero Fault |
| 52 |
Sensor failed Zero Cal |
| 53 |
Span Fault |
| 54 |
Sensor failed Span Cal |
| 55 |
Cal OK |
| 56 |
Calibration Successful |
| 57 |
Change Snsr Warn |
| 58 |
Sensor End Of Life Warning |
| 59 |
Snsr Swap Delay |
| 60 |
Sensor missing error held off during 2 min sensor Swap Delay, |
| 61 |
Change Snsr Fault |
| 62 |
Sensor End of Life indication |
| 63 |
Snsr Pwr Fault |
| 64 |
Sensor input voltage out of 7-30 volt range |
| 65 |
Device Comm Fault |
| 66 |
Sensor internal communications fault detected |
| 67 |
Cal Signal Enable |
| 68 |
Sets output set to 3.75 ma during cal and for 1 min after cal |
| 69 |
Alert Option Enable |
| 70 |
Alert option on sets cal output to 21 ma when Cal sig enabled |
| 71 |
Not Used |
| 72 |
Alarm1 Set |
| 73 |
Alarm 1 limit exceeded! |
| 74 |
Alarm2 Set |
| 75 |
Alarm 2 limit exceeded! |
| 76 |
Alarm3 Set |
| 77 |
Not Used |
| 78 |
Sensor Value(PV) |
| 79 |
.2f |
| 80 |
Snsr Dev fmly |
| 81 |
Snsr Class |
| 82 |
Snsr PDQ |
| 83 |
Snsr LS |
| 84 |
Snsr Fmly stat |
| 85 |
Snsr Upper Limit |
| 86 |
Snsr Lower Limit |
| 87 |
Snsr Minimum Span |
| 88 |
Snsr Damping |
| 89 |
.3f |
| 90 |
8.3f |
| 91 |
Sensor Serial Number |
| 92 |
7d |
| 93 |
Snsr Lower trim |
| 94 |
Snsr Upper trim |
| 95 |
4.2f |
| 96 |
Snsr Trim support |
| 97 |
Snsr Min lower trim |
| 98 |
Snsr Max lower trim |
| 99 |
Snsr Min upper trim |
| 100 |
Snsr Max upper trim |
| 101 |
Snsr Min trim diff |
| 102 |
Gas Snsr |
| 103 |
Input Voltage |
| 104 |
Input voltage monitor |
| 105 |
volts |
| 106 |
.1f |
| 107 |
Gas table |
| 108 |
Gas specific calibration look up table |
| 109 |
Methane |
| 110 |
Uses methane analyte curve |
| 111 |
Propane |
| 112 |
Uses propane analyte curve |
| 113 |
Ethane |
| 114 |
Uses ethane analyte curve |
| 115 |
n-Butane |
| 116 |
Uses n-butane analyte curve |
| 117 |
n-Pentane |
| 118 |
Uses n-pentane analyte curve |
| 119 |
n-Hexane |
| 120 |
Uses n-hexane analyte curve |
| 121 |
Cyclopentane |
| 122 |
Uses cyclopentane analyte curve |
| 123 |
Ethylene |
| 124 |
Uses ethylene analyte curve |
| 125 |
Acetylene |
| 126 |
Uses acetylene analyte curve |
| 127 |
5000 PPM CO2 |
| 128 |
Uses 5000PPM CO2 analyte curve |
| 129 |
5% CO2 |
| 130 |
Uses 5% CO2 analyte curve |
| 131 |
2% CO2 |
| 132 |
Uses 2% CO2 analyte curve |
| 133 |
Custom |
| 134 |
Uses custom analyte curve |
| 135 |
Unused |
| 136 |
Gas tables unused |
| 137 |
RTC Hrs |
| 138 |
Real time clock - hours |
| 139 |
hrs |
| 140 |
2d |
| 141 |
3d |
| 142 |
RTC Minutes |
| 143 |
Real time clock - minutes |
| 144 |
mins |
| 145 |
min value |
| 146 |
Minimum gas value reading recorded during average interval. |
| 147 |
max value |
| 148 |
Maximum gas reading recorded during average interval. |
| 149 |
avg value |
| 150 |
Average gas reading recorded during the average interval |
| 151 |
avg interval |
| 152 |
Time interval in hours(1,8, or 24) for which the min, max and average values are accumulated. |
| 153 |
hr |
| 154 |
alm1 setpoint |
| 155 |
Gas level at which alarm 1 will be set |
| 156 |
alm2 setpoint |
| 157 |
Gas level at which alarm 2 will be set |
| 158 |
alm3 setpoint |
| 159 |
Gas level at which alarm 3 will be set |
| 160 |
Setpoint edit val |
| 161 |
|
| 162 |
Alm edit num |
| 163 |
number of the alarm to be edited(1,2 or 3) |
| 164 |
Alarm Actions |
| 165 |
Defines the direction, latch and enable modes of the setpoint alarm |
| 166 |
alarm enable |
| 167 |
Alarm - enabled = 1 |
| 168 |
alarm increasing |
| 169 |
Alarm - increasing = 1, decreasing = 0 |
| 170 |
alarm latching |
| 171 |
Alarm - latching = 1 |
| 172 |
alm1 actions |
| 173 |
Setpoint alarm 1 control actions |
| 174 |
alm 1 enable |
| 175 |
Alarm 1 - enabled = 1 |
| 176 |
alm 1 inc |
| 177 |
Alarm 1 - increasing = 1, decreasing = 0 |
| 178 |
alm 1 latch |
| 179 |
Alarm 1 - latching = 1 |
| 180 |
alm2 actions |
| 181 |
Setpoint alarm 2 control actions |
| 182 |
alm 2 enable |
| 183 |
Alarm 2 - enabled = 1 |
| 184 |
alm 2 inc |
| 185 |
Alarm 2 - increasing = 1, decreasing = 0 |
| 186 |
alm 2 latch |
| 187 |
Alarm 2 - latching = 1 |
| 188 |
alm3 actions |
| 189 |
Setpoint alarm 3 control actions |
| 190 |
alm 3 enable |
| 191 |
Alarm 3 - enabled = 1 |
| 192 |
alm 3 inc |
| 193 |
Alarm 3 - increasing = 1, decreasing = 0 |
| 194 |
alm 3 latch |
| 195 |
Alarm 3 - latching = 1 |
| 196 |
Cal Mode |
| 197 |
Calibration mode selection variable |
| 198 |
Sensor Zero |
| 199 |
Initiates sensor Zero sequence |
| 200 |
Standard Cal |
| 201 |
Iniiates a Standard Zero and Span sequence |
| 202 |
Initial Cal |
| 203 |
Initiates an Initial Zero and Span sequence |
| 204 |
User Cal |
| 205 |
Initiates a manual User controlled cal sequence |
| 206 |
cal abort |
| 207 |
Calibration abort command byte |
| 208 |
Step Cal |
| 209 |
Calibration step command byte |
| 210 |
alm ack |
| 211 |
Alarm acknowledge command byte |
| 212 |
Auto Zero Comp |
| 213 |
Indicates the amount of automatic zero compensation added since last calibration |
| 214 |
Last Cal Date |
| 215 |
Indicates the date the sensor module was last calibrated |
| 216 |
Cal Signal |
| 217 |
When enabled, causes the 4-20 ma to be set to 3.75 ma during calibration |
| 218 |
Disabled |
| 219 |
Causes the output 4-20 ma signal to follow the gas reading during Cal |
| 220 |
Enabled |
| 221 |
Causes the output 4-20 ma to be set to 3.75 ma during Cal( 21 ma for Oxygen) |
| 222 |
Swap Delay |
| 223 |
Enables a 1 min hold off on sensor missing status bit and output current fault during sensor exchange |
| 224 |
Enables immediate Sensor Missing status bit on loss of sensor communication |
| 225 |
Enables a 1 min hold off on sensor missing status bit and output current fault during sensor exchange |
| 226 |
dataResetCmd |
| 227 |
Sensor data sheet reset command byte |
| 228 |
Sensor Status |
| 229 |
Status message from sensor module to transmitter |
| 230 |
SNSR Flash Flt |
| 231 |
help |
| 232 |
SNSR RAM Flt |
| 233 |
SNSR Pellement Flt |
| 234 |
SNSR TEDS Chksum Flt |
| 235 |
SNSR Pwr Flt |
| 236 |
SNSR IR Factory Mode |
| 237 |
SNSR IR Lamp Flt |
| 238 |
SNSR EEPROM R/W Flt |
| 239 |
SNSR EEPROM Chksum Flt |
| 240 |
SNSR Missing Flt |
| 241 |
SNSR Neg Pwr Flt |
| 242 |
SNSR IR Ref Flt |
| 243 |
SNSR Temp Flt |
| 244 |
SNSR IR Analyt Flt |
| 245 |
SNSR IR Low Sig Flt |
| 246 |
SNSR IR Param Flt |
| 247 |
SNSR Cal Flt |
| 248 |
SNSR Zero Mode |
| 249 |
SNSR Span Mode |
| 250 |
SNSR Sleep Mode |
| 251 |
SNSR Warm Up Mode |
| 252 |
SNSR POR Mode |
| 253 |
SNSR OK |
| 254 |
Main Code Ver |
| 255 |
main processor code version |
| 256 |
Snsr Temp |
| 257 |
Temperature reading from sensor module |
| 258 |
C |
| 259 |
Alert Option |
| 260 |
Sets output to 3.75 ma during cal of an Oxygen sensor if Cal sig is also enabled) |
| 261 |
Causes the output 4-20 ma to be set to 3.75 ma during Cal of an Oxygen sensor if Cal signal is enabled) |
| 262 |
Write Protect Mode |
| 263 |
Write protects device preventing variables or calibration from being changed |
| 264 |
Device write protection is disabled |
| 265 |
Device write protection is enabled |
| 266 |
DR_Initiate |
| 267 |
DR_Running |
| 268 |
DR_Conflict |
| 269 |
Sensor Calibration |
| 270 |
Abort Cal |
| 271 |
aborts device calibration sequence |
| 272 |
cal fault |
| 273 |
Alarm Function Edit |
| 274 |
Changes the alarm function controls |
| 275 |
Setpoint Edit |
| 276 |
Changes the device alarm level settings |
| 277 |
Clear Config Flag |
| 278 |
Clears device configuration flag |
| 279 |
Alarm Acknowledge |
| 280 |
Acknowledges latched alarms in the device |
| 281 |
Set Avg Interval |
| 282 |
Select a time collection interval for Min, Max and Average readings |
| 283 |
Sensor Reset |
| 284 |
Reset Sensor module to factory defaults |
| 285 |
Enable or disable device write protect mode |
| 286 |
Re-range |
| 287 |
Abgl.punkte Sensor |
| 288 |
Alarm Edit |
| 289 |
Clock edit |
| 290 |
Gas Sensor |
| 291 |
Edit Menu |
| 292 |
Cal Menu |
| 293 |
Swap Delay Edit |
| 294 |
Write Protect Edit |
| 295 |
8u |
| 296 |
Output Status |
| 297 |
Output Status Byte |
| 298 |
Uninitialized |
| 299 |
Normal - one sensor |
| 300 |
Normal - two sensors |
| 301 |
Normal - three sensors |
| 302 |
Shorted |
| 303 |
Shorted- shorted field wiring. |
| 304 |
Limited high |
| 305 |
Limited high- block can not respond to upward movement of value. |
| 306 |
Open |
| 307 |
Open- open field wiring. |
| 308 |
Limited low |
| 309 |
Limited low- block can not respond to upward movement of target. |
| 310 |
Initialization done |
| 311 |
Initialization done- block initialization is complete. |
| 312 |
Not selected |
| 313 |
Not selected- target value provided by block was not selected. |
| 314 |
No path |
| 315 |
No path- there is no path to the process. |
| 316 |
Fail |
| 317 |
Fail- hardware failure. |
| 318 |
Bad |
| 319 |
Bad- block is out of service or has bad input. |
| 320 |
Not from process |
| 321 |
Not from process- value is not directly affected by any process information. |
| 322 |
Local override |
| 323 |
Local override- block has LO mode. |
| 324 |
Not Cascade Mode |
| 325 |
Not RCas Mode |
| 326 |
Not ROut Mode |
| 327 |
No communication |
| 328 |
No communication- (NO_COM). |
| 329 |
uint16_var_blk_char |
| 330 |
uint32_var_blk_char |
| 331 |
uint8_var_blk_char |
| 332 |
int8_var_blk_char |
| 333 |
new itest redef1 label |