Device dictionary

Loading…

Reference ID	String
0	Sensor default
1	Configuration default
2	System default
3	Self test result
4	Meas. Unit
5	Sensor temperature unit - Engineering unit to be displayed with sensor temperature
6	Temperature Class
7	Temperature PDQ
8
9	Temperature LS
10	Temperature device status
11	Probe Break Detected
12	Upper probe limit
13	.3f
14	Lower probe limit
15	Temperature minimum span
16	8.3f
17	Temperature update period
18	s
19	Serial number of temperature sensor
20	7d
21	Simulate
22	Primary Variable - Temperature
23	Update period
24	Setup
25	Temperature sensor
26	Manufacturer specific setup
27	Temperature family setup
28	Line compensation resistance (Ohms)
29	.2f
30	Device Reset
31	Reset default configuration
32	Transducer MCU firmware
33	Nbr. Wires
34	Number of wires linked to the probe
35	2 Wires
36	3 Wires
37	4 Wires
38	Probe Type
39	Probe type linked to the device
40	Voltage -10..60 mV
41	Resistance 0..360 Ohms
42	Resistance 0..4000 Ohms
43	Probe PT100
44	Probe PT1000
45	Probe NI100
46	Probe NI1000
47	Probe TC type J
48	Probe TC type K
49	Probe TC type B
50	Probe TC type R
51	Probe TC type S
52	Probe TC type T
53	Probe TC type E
54	Probe TC type N
55	Probe TC type W
56	Temperature standard
57	ITS-90
58	Probe connection type
59	Single
60	Differential
61	Cold junction compensation type
62	Internal
63	External
64	Manual cold junction compensation
65	Not Used
66	Sensor temperature unit
67	Sensor temperature unit - Engineering unit to be displayed with sensor temperature
68	Unsupported probe type
69	Invalid number of wires
70	Set probe configuration
71	Invalid cold junction compensation type
72	PV Analog Channel Saturated
73	PV Analog Channel Fixed
74	Wireless
75	WirelessHART Device
76	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
77	Primary
78	Primary Analog Channel
79	Secondary
80	Secondary Analog Channel
81	Tertiary
82	Tertiary Analog Channel
83	Quaternary
84	Quaternary Analog Channel
85	Quinary
86	Quinary Analog Channel
87	Critical Power Failure
88	Lock all
89	Trim not supported
90	Configuration cannot be changed
91	Locked by gateway
92	Analog Input Channel
93	Analog Output Channel
94	Secondary Analog Channel Saturated
95	Tertiary Analog Channel Saturated
96	Quaternary Analog Channel Saturated
97	Quinary Analog Channel Saturated
98	Secondary Analog Channel Fixed
99	Tertiary Analog Channel Fixed
100	Quaternary Analog Channel Fixed
101	Quinary Analog Channel Fixed
102	Simulation active
103	The device is in simulation mode and the level output is not representative of the process.
104	Non-Volatile memory failure
105	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
106	Volatile memory error
107	The RAM memory check is invalid or maybe corrupt
108	Watchdog reset executed
109	A watchdog reset has been performed
110	Voltage conditions out of range
111	A voltage condition is outside its allowable range
112	Environmental conditions out of range
113	An internal or environmental condition is beyond acceptable limits.
114	Electronic failure
115	A hardware problem not related to the sensor has been detected.
116	Subdevice list changed
117	Duplicate master detected
118	Capacity Denied
119	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
120	Bandwidth allocation pending
121	Block transfer pending
122	Battery life
123	Percent range
124	Loop current
125	Primary variable
126	Secondary variable
127	Tertiary variable
128	Quaternary variable
129	Read receive time
130	Write date and time
131	Non-Volatile Clock
132	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
133	Clock Uninitialized
134	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
135	None
136	No restrictions
137	SI Only
138	Restricted to SI Unit codes only
139	Process automation device
140	Discrete device
141	Hybrid:Process automation+discrete
142	I/O System
143	WirelessHART Process automation device
144	WirelessHART Discrete device
145	WirelessHART Process automation+discrete
146	WirelessHART Gateway
147	WirelessHART Access point
148	WirelessHART Process adapter
149	WirelessHART Discrete adapter
150	WirelessHART enabled handheld/portable maintenance tool
151	Device Profile
152	US
153	United States of America
154	JP
155	Japan
156	DE
157	Germany
158	FR
159	France
160	ES
161	Spain
162	RU
163	Russian Federation
164	CN
165	People's Republic of China
166	Secondary Master
167	Primary Master
168	Device Diagnostic Status 0
169	Device Diagnostic Status 1
170	I/O and Subdevice Status
171	WirelessHART Status
172	Time Set Option
173	Real Time Clock Flags
174	Country
175	Country of intended device installation
176	SI Unit Control
177	Indicates if device should only display SI unit codes
178	8u
179	Dynamic Variables Returned for Device Variables
180	Command Response Truncated
181	Configuration Change Counter Mismatch
182	Status bytes mismatch
183	Device Variable
184	Output Status
185	Output Status Byte
186	Uninitialized
187	Normal - one sensor
188	Normal - two sensors
189	Normal - three sensors
190	Shorted
191	Shorted- shorted field wiring.
192	Limited high
193	Limited high- block can not respond to upward movement of value.
194	Open
195	Open- open field wiring.
196	Limited low
197	Limited low- block can not respond to upward movement of target.
198	Initialization done
199	Initialization done- block initialization is complete.
200	Not selected
201	Not selected- target value provided by block was not selected.
202	No path
203	No path- there is no path to the process.
204	Fail
205	Fail- hardware failure.
206	Bad
207	Bad- block is out of service or has bad input.
208	Not from process
209	Not from process- value is not directly affected by any process information.
210	Local override
211	Local override- block has LO mode.
212	Not Cascade Mode
213	Not RCas Mode
214	Not ROut Mode
215	No communication
216	No communication- (NO_COM).
217	uint16_var_blk_char
218	uint32_var_blk_char
219	uint8_var_blk_char
220	int8_var_blk_char
221	new itest redef1 label
Reference ID	String