Device dictionary

Loading…

Reference ID	String
0	PID901
1	Nuoan
2	Concentration
3	Concentration value measured by device.
4	.1f
5	Concentration unit
6	Conc Dev fmly
7	Conc Class
8	Conc PDQ
9	Conc LS
10	Conc Fmly stat
11	Conc USL
12	Conc LSL
13	Conc min span
14	Conc damp
15	Conc snsr s/n
16	7d
17	Primary Device Variable (deviceVariables[0]) is concentration
18	Snsr temp unit
19	Sensor Temperature Units - Engineering unit to be displayed with Sensor Temperature.
20	Temp Class
21	Temp PDQ
22
23	Temp LS
24	Temp Dev Stat
25	2th Variable - Temperature Compensation
26	Concentration
27	Temperatuer
28	Alarm Low parameter
29	Alarm Low parameter.
30	Alarm High parameter
31	Alarm High parameter.
32	Calibration parameter
33	Sensor calibration parameter.
34	.2f
35	Device Settings
36	Diagnostics
37	Maintenance
38	Offline
39	Empty
40	Process Variables
41	Device Setup
42	Alarm Setup
43	Cali Display
44	PV Analog Channel Saturated
45	PV Analog Channel Fixed
46	Wireless
47	WirelessHART Device
48	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
49	Primary
50	Primary Analog Channel
51	Secondary
52	Secondary Analog Channel
53	Tertiary
54	Tertiary Analog Channel
55	Quaternary
56	Quaternary Analog Channel
57	Quinary
58	Quinary Analog Channel
59	Critical Power Failure
60	Lock all
61	Trim not supported
62	Configuration cannot be changed
63	Locked by gateway
64	Analog Input Channel
65	Analog Output Channel
66	Secondary Analog Channel Saturated
67	Tertiary Analog Channel Saturated
68	Quaternary Analog Channel Saturated
69	Quinary Analog Channel Saturated
70	Secondary Analog Channel Fixed
71	Tertiary Analog Channel Fixed
72	Quaternary Analog Channel Fixed
73	Quinary Analog Channel Fixed
74	Simulation active
75	The device is in simulation mode and the level output is not representative of the process.
76	Non-Volatile memory failure
77	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
78	Volatile memory error
79	The RAM memory check is invalid or maybe corrupt
80	Watchdog reset executed
81	A watchdog reset has been performed
82	Voltage conditions out of range
83	A voltage condition is outside its allowable range
84	Environmental conditions out of range
85	An internal or environmental condition is beyond acceptable limits.
86	Electronic failure
87	A hardware problem not related to the sensor has been detected.
88	Subdevice list changed
89	Duplicate master detected
90	Capacity Denied
91	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
92	Bandwidth allocation pending
93	Block transfer pending
94	Battery life
95	Percent range
96	Loop current
97	Primary variable
98	Secondary variable
99	Tertiary variable
100	Quaternary variable
101	Read receive time
102	Write date and time
103	Non-Volatile Clock
104	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
105	Clock Uninitialized
106	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
107	None
108	No restrictions
109	SI Only
110	Restricted to SI Unit codes only
111	Process automation device
112	Discrete device
113	Hybrid:Process automation+discrete
114	I/O System
115	WirelessHART Process automation device
116	WirelessHART Discrete device
117	WirelessHART Process automation+discrete
118	WirelessHART Gateway
119	WirelessHART Access point
120	WirelessHART Process adapter
121	WirelessHART Discrete adapter
122	WirelessHART enabled handheld/portable maintenance tool
123	Device Profile
124	US
125	United States of America
126	JP
127	Japan
128	DE
129	Germany
130	FR
131	France
132	ES
133	Spain
134	RU
135	Russian Federation
136	CN
137	People's Republic of China
138	Secondary Master
139	Primary Master
140	Device Diagnostic Status 0
141	Device Diagnostic Status 1
142	I/O and Subdevice Status
143	WirelessHART Status
144	Time Set Option
145	Real Time Clock Flags
146	Country
147	Country of intended device installation
148	SI Unit Control
149	Indicates if device should only display SI unit codes
150	8u
151	Dynamic Variables Returned for Device Variables
152	Command Response Truncated
153	Configuration Change Counter Mismatch
154	Status bytes mismatch
155	8.3f
156	.3f
157	Output Status
158	Output Status Byte
159	Uninitialized
160	Normal - one sensor
161	Normal - two sensors
162	Normal - three sensors
163	Shorted
164	Shorted- shorted field wiring.
165	Limited high
166	Limited high- block can not respond to upward movement of value.
167	Open
168	Open- open field wiring.
169	Limited low
170	Limited low- block can not respond to upward movement of target.
171	Initialization done
172	Initialization done- block initialization is complete.
173	Not selected
174	Not selected- target value provided by block was not selected.
175	No path
176	No path- there is no path to the process.
177	Fail
178	Fail- hardware failure.
179	Bad
180	Bad- block is out of service or has bad input.
181	Not from process
182	Not from process- value is not directly affected by any process information.
183	Local override
184	Local override- block has LO mode.
185	Not Cascade Mode
186	Not RCas Mode
187	Not ROut Mode
188	No communication
189	No communication- (NO_COM).
190	uint16_var_blk_char
191	uint32_var_blk_char
192	uint8_var_blk_char
193	int8_var_blk_char
194	new itest redef1 label
Reference ID	String