Device dictionary

Loading…

Reference ID	String
0	MFT B-Series
1	Kurz Instruments
2	Device Long Tag � up to 32 characters
3	Device Short Tag � up to 8 characters. The Device Short Tag is mapped to the first 8 characters of the KURZ MFTB Tag Name. A change made to the Device Short Tag will be reflected in the MFTB Tag Name which is displayed on the MFTB local display
4	Rp resistance above high limit
5	Rp resistance below low limit
6	Rtc resistance above high limit
7	Rtc resistance below low limit
8	Wire Resistance above high limit
9	Sensor RPS lead open circuit
10	High sensor or wire leakage current
11	Flow rate above design limits
12	Reserved
13	ADC failed to convert data
14	Sensor control stopped responding
15	Sensor control crowbar engaged
16	Sensor type does not match config
17	Abnormal sensor node voltages
18	Unable to write new config file
19	Sensor Type Does Not Match Board
20	HART Warning: Subsystem Fail
21	Sensor leak warning S-GND below 100K
22	Power was applied
23	Change made to Configuration
24	Device in Diagnostic Mode
25	Fixed current output
26	Fault Event in MFTB
27	Analog output saturated
28	MFTB Alarm 1
29	MFTB Alarm 2
30	Zero Drift Test in progress
31	Mid-span Drift Test in progress
32	Full-span Drift Test in progress
33	Drift Check Cycle All Tests
34	Purge Start Flag
35	Unused
36	.3f
37	PV Units
38	SV Units
39	Temperature Units
40	Total Flow Units
41	PV
42	Process flow rate or flow velocity; depends on PV units selected
43	.4f
44	SV
45	Temperature
46	Temperature of flow medium
47	.2f
48	Totalized Flow
49	Totalized process flow
50	Flow rate DAMP
51	Damping value or filter time constant
52	.5f
53	sec
54	Flow rate USL
55	Flow rate LSL
56	Flow rate min span
57	Correction Bias
58	Bias Correction Factor
59	Corr Units
60	Number of Correction Pts
61	# of Correction Data Points
62	1d
63	Reference value 1
64	Reference Reading 1
65	Reference value 2
66	Reference Reading 2
67	Reference value 3
68	Reference Reading 3
69	Reference value 4
70	Reference Reading 4
71	Reference value 5
72	Reference Reading 5
73	Reference value 6
74	Reference Reading 6
75	Reference value 7
76	Reference Reading 7
77	Reference value 8
78	Reference Reading 8
79	Test Data 1
80	Indicated Reading 1
81	Test Data 2
82	Indicated Reading 2
83	Test Data 3
84	Indicated Reading 3
85	Test Data 4
86	Indicated Reading 4
87	Test Data 5
88	Indicated Reading 5
89	Test Data 6
90	Indicated Reading 6
91	Test Data 7
92	Indicated Reading 7
93	Test Data 8
94	Indicated Reading 8
95	Total CF
96	Total Correction Factor
97	Flow Area
98	Cross-sectional Flow Area. The flow area can be entered by providing the dimensions of the duct. If the duct is round, the user shall enter the inside diameter. If the duct is rectangular, the user shall enter the inside height and width.
99	Area Units
100	Engineering units for Cross-Sectional Flow Area
101	SQFT
102	Square Feet
103	SQM
104	Square Meters
105	Last Cal Date
106	Date of last factory calibration of sensor (flow calibration)
107	Auto Purge OnOff
108	Auto Purge Function OnOff - Enable/Disable purge triggered by internal timer
109	OFF
110	ON
111	Width
112	Duration that Purge digital out is pulsed ON
113	5d
114	msec
115	Purge Dout
116	Purge Function Assigned Digital Out
117	Hold Time
118	Delay after purge before resuming device output
119	Interval
120	Purge Interval for Auto Purge
121	4d
122	min
123	Auto Drift Check OnOff
124	Auto Drift Check ON/OFF
125	Drift Check interval time for auto drift check
126	hour
127	% FS at Zero
128	Percent of full scale applied voltage for Zero Drift Check test
129	%
130	% FS at Mid
131	Percent of full scale applied voltage for Mid-Span Drift Check test
132	% FS at Span
133	Percent of full scale applied voltage for Full-Span Drift Check test
134	Duration at Zero
135	Duration of Zero Drift Check test
136	3d
137	Duration at Mid
138	Duration of Mid-Span Drift Check test
139	Duration at Span
140	Duration of Full-Span Drift Check test
141	Vin Zero
142	Zero Drift Check applied voltage
143	.7f
144	Volts
145	Vin Mid
146	Mid-Span Drift Check applied voltage
147	Vin Span
148	Full-Span Drift Check applied voltage
149	Vout Zero
150	Zero Drift Check read voltage
151	Vout Mid
152	Mid-Span Drift Check read voltage
153	Vout Span
154	Full-Span Drift Check read voltage
155	% Drift at Zero
156	Zero check Drift
157	% Drift at Mid
158	Mid Check Drift
159	% Drift at Span
160	Span Check Drift
161	DriftChk Cmd
162	Drift Check command mask indicates which drift test to execute � Bit 0 set to 1 Zero Drift Check; Bit 1 set to 1 Mid-Span Check; Bit 2 set to 1 Full-Span Check
163	Perform Zero drift check
164	Perform Mid drift check
165	Perform Span drift check
166	Perform drift check cycle
167	VPs
168	VPs = voltage acrross Ps to Gnd
169	VIph
170	Viph = voltage across Iph to Gnd
171	VRtch
172	Vrtch = voltage across Rtch to Gnd
173	VRtcl
174	VRtcl = voltage acroos Rtcl to Gnd
175	VLl
176	Vll = voltage across Ll to Gnd
177	VLeakSense
178	VleakSense = voltage across LeakSense to Gnd
179	VExtIn
180	VextIn = voltage across ExtIn to Gnd
181	VTemp
182	Vtemp = voltage across Temp to Gnd
183	VCal
184	Vcal = voltage read from the independent calibrator
185	Electronic Temp
186	Electronics Temperature
187	Run Time
188	MFT-B accumulated run time hours
189	Hours
190	Rp Current
191	Ampere
192	Rp Power
193	Watt
194	Rp Resistance
195	Rp Resostance
196	Ohm
197	Rtc Resistance
198	Sensor Wire R
199	Sensor Wire Resistance
200	Sensor Leak R
201	Sensor Leak Resistance
202	KOhm
203	Std Temp Unit
204	Standard Temperature Units
205	Std Press Unit
206	Standard Pressure Units
207	Std Temp
208	Standard Temperature
209	Std Absolute Press
210	Standard Pressure
211	Flow rate snsr s/n
212	7d
213	Velocity snsr s/n
214	Temperature snsr s/n
215	Total flow snsr s/n
216	Flowrate Classification
217
218	velocity Classification
219	temperature Classification
220	totalflow Classification
221	Flowrate Data Quality
222	Flowrate Limit Status
223	Flowrate Device Family Status
224	velocity Data Quality
225	velocity Limit Status
226	velocity Device Family Status
227	temperature Data Quality
228	temperature Limit Status
229	temperature Device Family Status
230	totalflow Data Quality
231	totalflow Limit Status
232	totalflow Device Family Status
233	Flowrate or Massrate
234	Velocity
235	Total Flow
236	Device Monitor
237	Setup
238	Flow Correction Coefficients
239	Flow Cal Data
240	Purge Setup
241	Drift Check Setup
242	Utilities
243	Common
244	Device Specific
245	Drift Check
246	Diagnostic Measurements
247	Drift Check Results
248	Input Voltage
249	Sensor Output
250	Correction Data Sets
251	VCF Data Set 1
252	VCF Data Set 2
253	VCF Data Set 3
254	VCF Data Set 4
255	VCF Data Set 5
256	VCF Data Set 6
257	VCF Data Set 7
258	VCF Data Set 8
259	Analog Output
260	Basic Setup
261	Device Error Status
262	Device Status
263	Process Variables
264	HART Device Data
265	Offline Variables
266	Calculate Flow Area
267	Run Drift Check
268	Calibrate URV
269	Sets the current Upper Range Value (20mA Ouput) to the present value of the Primary Variable.
270	Calibrate LRV
271	Sets the current Lower Range Value (4mA Ouput) to the present value of the Primary Variable.
272	Reset Device
273	Reset Config Changed Flag
274	Reset Totalizer
275	Start Purge
276	Triggers a gas purge cleaning of the flow meter sensor
277	Calibrate 4-20mA Output
278	PV Analog Channel Saturated
279	PV Analog Channel Fixed
280	Wireless
281	WirelessHART Device
282	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
283	Primary
284	Primary Analog Channel
285	Secondary
286	Secondary Analog Channel
287	Tertiary
288	Tertiary Analog Channel
289	Quaternary
290	Quaternary Analog Channel
291	Quinary
292	Quinary Analog Channel
293	Critical Power Failure
294	Lock all
295	Trim not supported
296	Configuration cannot be changed
297	Locked by gateway
298	Analog Input Channel
299	Analog Output Channel
300	Secondary Analog Channel Saturated
301	Tertiary Analog Channel Saturated
302	Quaternary Analog Channel Saturated
303	Quinary Analog Channel Saturated
304	Secondary Analog Channel Fixed
305	Tertiary Analog Channel Fixed
306	Quaternary Analog Channel Fixed
307	Quinary Analog Channel Fixed
308	Simulation active
309	The device is in simulation mode and the level output is not representative of the process.
310	Non-Volatile memory failure
311	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
312	Volatile memory error
313	The RAM memory check is invalid or maybe corrupt
314	Watchdog reset executed
315	A watchdog reset has been performed
316	Voltage conditions out of range
317	A voltage condition is outside its allowable range
318	Environmental conditions out of range
319	An internal or environmental condition is beyond acceptable limits.
320	Electronic failure
321	A hardware problem not related to the sensor has been detected.
322	Subdevice list changed
323	Duplicate master detected
324	Capacity Denied
325	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
326	Bandwidth allocation pending
327	Block transfer pending
328	Battery life
329	Percent range
330	Loop current
331	Primary variable
332	Secondary variable
333	Tertiary variable
334	Quaternary variable
335	Read receive time
336	Write date and time
337	Non-Volatile Clock
338	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
339	Clock Uninitialized
340	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
341	None
342	No restrictions
343	SI Only
344	Restricted to SI Unit codes only
345	Process automation device
346	Discrete device
347	Hybrid:Process automation+discrete
348	I/O System
349	WirelessHART Process automation device
350	WirelessHART Discrete device
351	WirelessHART Process automation+discrete
352	WirelessHART Gateway
353	WirelessHART Access point
354	WirelessHART Process adapter
355	WirelessHART Discrete adapter
356	WirelessHART enabled handheld/portable maintenance tool
357	Device Profile
358	US
359	United States of America
360	JP
361	Japan
362	DE
363	Germany
364	FR
365	France
366	ES
367	Spain
368	RU
369	Russian Federation
370	CN
371	People's Republic of China
372	Secondary Master
373	Primary Master
374	Device Diagnostic Status 0
375	Device Diagnostic Status 1
376	I/O and Subdevice Status
377	WirelessHART Status
378	Time Set Option
379	Real Time Clock Flags
380	Country
381	Country of intended device installation
382	SI Unit Control
383	Indicates if device should only display SI unit codes
384	8u
385	Dynamic Variables Returned for Device Variables
386	Command Response Truncated
387	Configuration Change Counter Mismatch
388	Status bytes mismatch
389	8.3f
390	Output Status
391	Output Status Byte
392	Uninitialized
393	Normal - one sensor
394	Normal - two sensors
395	Normal - three sensors
396	Shorted
397	Shorted- shorted field wiring.
398	Limited high
399	Limited high- block can not respond to upward movement of value.
400	Open
401	Open- open field wiring.
402	Limited low
403	Limited low- block can not respond to upward movement of target.
404	Initialization done
405	Initialization done- block initialization is complete.
406	Not selected
407	Not selected- target value provided by block was not selected.
408	No path
409	No path- there is no path to the process.
410	Fail
411	Fail- hardware failure.
412	Bad
413	Bad- block is out of service or has bad input.
414	Not from process
415	Not from process- value is not directly affected by any process information.
416	Local override
417	Local override- block has LO mode.
418	Not Cascade Mode
419	Not RCas Mode
420	Not ROut Mode
421	No communication
422	No communication- (NO_COM).
423	uint16_var_blk_char
424	uint32_var_blk_char
425	uint8_var_blk_char
426	int8_var_blk_char
427	new itest redef1 label
Reference ID	String