| 0 |
Freq --> mA |
| 1 |
HOFFER FLOW CNTRLS |
| 2 |
Operation Status |
| 3 |
Loop Current Override. |
| 4 |
Dac Gain Not Calibrated. |
| 5 |
Dac Zero Not Calibrated. |
| 6 |
Flow rate exceeds display. |
| 7 |
Flow exceeds 20 mA calibration. |
| 8 |
Pulse rate overflow. |
| 9 |
Sample Time Configuration Error. |
| 10 |
Rate Decimal Pt. Configuration Error. |
| 11 |
Total Decimal Pt. Configuration Error. |
| 12 |
Number Of Pts. Configuration Error. |
| 13 |
KFactor Decimal Pt. Configuration Error. |
| 14 |
Linearization Configuration Error. |
| 15 |
Rate Time Units Configuration Error. |
| 16 |
Total Units Configuration Error. |
| 17 |
Alarm 1 Function Configuration Error. |
| 18 |
Alarm 2 Function Configuration Error. |
| 19 |
Unit Locked. |
| 20 |
Pulse Frequency Configuration Error. |
| 21 |
Pulse Scale Configuration Error. |
| 22 |
Alarm 1 Being Tested. |
| 23 |
Alarm 2 Being Tested. |
| 24 |
Pulse Output Being Tested. |
| 25 |
Alarm 1 Activated |
| 26 |
Alarm 2 Activated. |
| 27 |
Critical Power Failure. |
| 28 |
Device Variable Alert. |
| 29 |
Maintenance Required. |
| 30 |
Electronic Defect |
| 31 |
Environmental Conditions Out of Range. |
| 32 |
Voltage Out of Range. |
| 33 |
Watchdog Reset Executed. |
| 34 |
Volatile Memory Defect. |
| 35 |
Non-volatile Memory Defect. |
| 36 |
Simulation Active. |
| 37 |
Lower flow rate for 4 mA output. |
| 38 |
8.0f |
| 39 |
9.1f |
| 40 |
9.2f |
| 41 |
9.3f |
| 42 |
Upper flow rate for 20 mA output. |
| 43 |
Rate % Range |
| 44 |
Flow Rate |
| 45 |
Total |
| 46 |
Grand Total |
| 47 |
Frequency |
| 48 |
Rate |
| 49 |
Damping |
| 50 |
Flow Rate Units |
| 51 |
l/day |
| 52 |
Rate of flow expressed as units/time. |
| 53 |
USL |
| 54 |
LSL |
| 55 |
7d |
| 56 |
Not Classified |
| 57 |
Rate Units |
| 58 |
Time base for flowrate measurement. |
| 59 |
Seconds |
| 60 |
Minutes |
| 61 |
Hours |
| 62 |
Days |
| 63 |
Units |
| 64 |
M3 |
| 65 |
FT3 |
| 66 |
Flow total in selected units. |
| 67 |
Grand flow total in selected units. |
| 68 |
Measured Input Frequency in Hz. |
| 69 |
5.1f |
| 70 |
Hz |
| 71 |
Rate Decimal Point Location |
| 72 |
Select resolution for displaying flow rate. |
| 73 |
00000 |
| 74 |
0000.0 |
| 75 |
000.00 |
| 76 |
00.000 |
| 77 |
Total Decimal Point Location |
| 78 |
Select resolution for displaying flow total. |
| 79 |
00000000 |
| 80 |
0000000.0 |
| 81 |
000000.00 |
| 82 |
00000.000 |
| 83 |
Linearization |
| 84 |
Select method of flowmeter linearization. |
| 85 |
Average K factor |
| 86 |
Linearization Table |
| 87 |
K Factor Decimal Point Location |
| 88 |
Select K-Factor resolution. |
| 89 |
Average K Factor |
| 90 |
Enter value for Average K-Factor. |
| 91 |
Number of Points in Table |
| 92 |
Enter the number of points in linearization table. |
| 93 |
Correction Factor |
| 94 |
Enter multiplier to correct flow rate and total. |
| 95 |
.3f |
| 96 |
Frequency Pt. 1 |
| 97 |
Frequency point 1. |
| 98 |
11.3f |
| 99 |
Frequency Pt. 2 |
| 100 |
Frequency point 2. |
| 101 |
Frequency Pt. 3 |
| 102 |
Frequency point 3. |
| 103 |
Frequency Pt. 4 |
| 104 |
Frequency point 4. |
| 105 |
Frequency Pt. 5 |
| 106 |
Frequency point 5. |
| 107 |
Frequency Pt. 6 |
| 108 |
Frequency point 6. |
| 109 |
Frequency Pt. 7 |
| 110 |
Frequency point 7. |
| 111 |
Frequency Pt. 8 |
| 112 |
Frequency point 8. |
| 113 |
Frequency Pt. 9 |
| 114 |
Frequency point 9. |
| 115 |
Frequency Pt. 10 |
| 116 |
Frequency point 10. |
| 117 |
Frequency Pt. 11 |
| 118 |
Frequency point 11. |
| 119 |
Frequency Pt. 12 |
| 120 |
Frequency point 12. |
| 121 |
Frequency Pt. 13 |
| 122 |
Frequency point 13. |
| 123 |
Frequency Pt. 14 |
| 124 |
Frequency point 14. |
| 125 |
Frequency Pt. 15 |
| 126 |
Frequency point 15. |
| 127 |
Frequency Pt. 16 |
| 128 |
Frequency point 16. |
| 129 |
Frequency Pt. 17 |
| 130 |
Frequency point 17. |
| 131 |
Frequency Pt. 18 |
| 132 |
Frequency point 18. |
| 133 |
Frequency Pt. 19 |
| 134 |
Frequency point 19. |
| 135 |
Frequency Pt. 20 |
| 136 |
Frequency point 20. |
| 137 |
KFactor Pt. 1 |
| 138 |
K-Factor 1. |
| 139 |
KFactor Pt. 2 |
| 140 |
K-Factor 2. |
| 141 |
KFactor Pt. 3 |
| 142 |
K-Factor 3. |
| 143 |
KFactor Pt. 4 |
| 144 |
K-Factor 4. |
| 145 |
KFactor Pt. 5 |
| 146 |
K-Factor 5. |
| 147 |
KFactor Pt. 6 |
| 148 |
K-Factor 6. |
| 149 |
KFactor Pt. 7 |
| 150 |
K-Factor 7. |
| 151 |
KFactor Pt. 8 |
| 152 |
K-Factor 8. |
| 153 |
KFactor Pt. 9 |
| 154 |
K-Factor 9. |
| 155 |
KFactor Pt. 10 |
| 156 |
K-Factor 10. |
| 157 |
KFactor Pt. 11 |
| 158 |
K-Factor 11. |
| 159 |
KFactor Pt. 12 |
| 160 |
K-Factor 12. |
| 161 |
KFactor Pt. 13 |
| 162 |
K-Factor 13. |
| 163 |
KFactor Pt. 14 |
| 164 |
K-Factor 14. |
| 165 |
KFactor Pt. 15 |
| 166 |
K-Factor 15. |
| 167 |
KFactor Pt. 16 |
| 168 |
K-Factor 16. |
| 169 |
KFactor Pt. 17 |
| 170 |
K-Factor 17. |
| 171 |
KFactor Pt. 18 |
| 172 |
K-Factor 18. |
| 173 |
KFactor Pt. 19 |
| 174 |
K-Factor 19. |
| 175 |
KFactor Pt. 20 |
| 176 |
K-Factor 20. |
| 177 |
|
| 178 |
Pulse Scale |
| 179 |
Set number of total units equal to one pulse. |
| 180 |
OFF |
| 181 |
1 |
| 182 |
10 |
| 183 |
100 |
| 184 |
Pulse Frequency |
| 185 |
Set frequency of burst of pulse out. |
| 186 |
2 |
| 187 |
4 |
| 188 |
8 |
| 189 |
Alarm 1 Function |
| 190 |
Select function for Alarm 1. |
| 191 |
RATE |
| 192 |
TOTAL |
| 193 |
Alarm 1 Level |
| 194 |
Enter Alarm 1 setpoint in selected flow units. |
| 195 |
Alarm 2 Function |
| 196 |
Select function for Alarm 2. |
| 197 |
Alarm 2 Level |
| 198 |
Enter Alarm 2 setpoint in selected flow units. |
| 199 |
invalid_index |
| 200 |
Alarm 1 Release |
| 201 |
Unlatch Alarm 1 output. |
| 202 |
Not Released |
| 203 |
Released |
| 204 |
Alarm 2 Release |
| 205 |
Unlatch Alarm 2 output. |
| 206 |
Alarm 1 Test |
| 207 |
Test Alarm 1 output. |
| 208 |
Alarm Set Low |
| 209 |
Alarm Set High |
| 210 |
Alarm 2 Test |
| 211 |
Test Alarm 2 output. |
| 212 |
Freq --> mA Tag |
| 213 |
Tag number for device. |
| 214 |
8u |
| 215 |
Max Sample Time |
| 216 |
Enter a number between 1 and 80 to increase the amount of time to wait for last sample. |
| 217 |
2u |
| 218 |
Password |
| 219 |
Enter 4-digit password. |
| 220 |
Change |
| 221 |
Compare |
| 222 |
Invalid Password |
| 223 |
Lock Unit |
| 224 |
Enable/Disable password protection. |
| 225 |
NO |
| 226 |
YES |
| 227 |
Current Mode |
| 228 |
Set mode for analog output. |
| 229 |
Follows rate |
| 230 |
Set to 4 mA |
| 231 |
Set to 12 mA |
| 232 |
Set to 20 mA |
| 233 |
Clear Total |
| 234 |
Clear the diplayed flow total. |
| 235 |
Set Total |
| 236 |
Write a flow total to the device. |
| 237 |
Pulse Test |
| 238 |
Generate 1Hz pulse output test signal. |
| 239 |
Set Alarm 1 ON |
| 240 |
Set Alarm 1 output on. |
| 241 |
Set Alarm 2 ON |
| 242 |
Change Lock Status |
| 243 |
TBD |
| 244 |
Start |
| 245 |
Process Variables |
| 246 |
Primary Variables |
| 247 |
Identification |
| 248 |
PV Measurement |
| 249 |
Range Values |
| 250 |
Measured Values |
| 251 |
HART Tags |
| 252 |
Device Info. |
| 253 |
Revisions |
| 254 |
PV |
| 255 |
LRV |
| 256 |
URV |
| 257 |
Device Diagnostics |
| 258 |
Summary |
| 259 |
Failed |
| 260 |
Warning |
| 261 |
Configuration |
| 262 |
Identity |
| 263 |
Device Status |
| 264 |
Test Status |
| 265 |
Alarm Status |
| 266 |
Overrange Conditions |
| 267 |
Configuration Status |
| 268 |
Device Setup |
| 269 |
Outputs Setup |
| 270 |
Meter Setup |
| 271 |
HART Setup |
| 272 |
Flow Setup |
| 273 |
Total Setup |
| 274 |
Pulse Setup |
| 275 |
Analog Setup |
| 276 |
Alarm 1 |
| 277 |
Alarm 2 |
| 278 |
KFactor |
| 279 |
Upload |
| 280 |
PV Analog Channel Saturated |
| 281 |
PV Analog Channel Fixed |
| 282 |
Wireless |
| 283 |
WirelessHART Device |
| 284 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 285 |
Primary |
| 286 |
Primary Analog Channel |
| 287 |
Secondary |
| 288 |
Secondary Analog Channel |
| 289 |
Tertiary |
| 290 |
Tertiary Analog Channel |
| 291 |
Quaternary |
| 292 |
Quaternary Analog Channel |
| 293 |
Quinary |
| 294 |
Quinary Analog Channel |
| 295 |
Critical Power Failure |
| 296 |
Lock all |
| 297 |
Trim not supported |
| 298 |
Configuration cannot be changed |
| 299 |
Locked by gateway |
| 300 |
Analog Input Channel |
| 301 |
Analog Output Channel |
| 302 |
Secondary Analog Channel Saturated |
| 303 |
Tertiary Analog Channel Saturated |
| 304 |
Quaternary Analog Channel Saturated |
| 305 |
Quinary Analog Channel Saturated |
| 306 |
Secondary Analog Channel Fixed |
| 307 |
Tertiary Analog Channel Fixed |
| 308 |
Quaternary Analog Channel Fixed |
| 309 |
Quinary Analog Channel Fixed |
| 310 |
Simulation active |
| 311 |
The device is in simulation mode and the level output is not representative of the process. |
| 312 |
Non-Volatile memory failure |
| 313 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 314 |
Volatile memory error |
| 315 |
The RAM memory check is invalid or maybe corrupt |
| 316 |
Watchdog reset executed |
| 317 |
A watchdog reset has been performed |
| 318 |
Voltage conditions out of range |
| 319 |
A voltage condition is outside its allowable range |
| 320 |
Environmental conditions out of range |
| 321 |
An internal or environmental condition is beyond acceptable limits. |
| 322 |
Electronic failure |
| 323 |
A hardware problem not related to the sensor has been detected. |
| 324 |
Subdevice list changed |
| 325 |
Duplicate master detected |
| 326 |
Capacity Denied |
| 327 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 328 |
Bandwidth allocation pending |
| 329 |
Block transfer pending |
| 330 |
Battery life |
| 331 |
Percent range |
| 332 |
Loop current |
| 333 |
Primary variable |
| 334 |
Secondary variable |
| 335 |
Tertiary variable |
| 336 |
Quaternary variable |
| 337 |
Read receive time |
| 338 |
Write date and time |
| 339 |
Non-Volatile Clock |
| 340 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 341 |
Clock Uninitialized |
| 342 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 343 |
None |
| 344 |
No restrictions |
| 345 |
SI Only |
| 346 |
Restricted to SI Unit codes only |
| 347 |
Process automation device |
| 348 |
Discrete device |
| 349 |
Hybrid:Process automation+discrete |
| 350 |
I/O System |
| 351 |
WirelessHART Process automation device |
| 352 |
WirelessHART Discrete device |
| 353 |
WirelessHART Process automation+discrete |
| 354 |
WirelessHART Gateway |
| 355 |
WirelessHART Access point |
| 356 |
WirelessHART Process adapter |
| 357 |
WirelessHART Discrete adapter |
| 358 |
WirelessHART enabled handheld/portable maintenance tool |
| 359 |
Device Profile |
| 360 |
US |
| 361 |
United States of America |
| 362 |
JP |
| 363 |
Japan |
| 364 |
DE |
| 365 |
Germany |
| 366 |
FR |
| 367 |
France |
| 368 |
ES |
| 369 |
Spain |
| 370 |
RU |
| 371 |
Russian Federation |
| 372 |
CN |
| 373 |
People's Republic of China |
| 374 |
Secondary Master |
| 375 |
Primary Master |
| 376 |
Device Diagnostic Status 0 |
| 377 |
Device Diagnostic Status 1 |
| 378 |
I/O and Subdevice Status |
| 379 |
WirelessHART Status |
| 380 |
Time Set Option |
| 381 |
Real Time Clock Flags |
| 382 |
Country |
| 383 |
Country of intended device installation |
| 384 |
SI Unit Control |
| 385 |
Indicates if device should only display SI unit codes |
| 386 |
Dynamic Variables Returned for Device Variables |
| 387 |
Command Response Truncated |
| 388 |
Configuration Change Counter Mismatch |
| 389 |
Status bytes mismatch |
| 390 |
8.3f |
| 391 |
Output Status |
| 392 |
Output Status Byte |
| 393 |
Uninitialized |
| 394 |
Normal - one sensor |
| 395 |
Normal - two sensors |
| 396 |
Normal - three sensors |
| 397 |
Shorted |
| 398 |
Shorted- shorted field wiring. |
| 399 |
Limited high |
| 400 |
Limited high- block can not respond to upward movement of value. |
| 401 |
Open |
| 402 |
Open- open field wiring. |
| 403 |
Limited low |
| 404 |
Limited low- block can not respond to upward movement of target. |
| 405 |
Initialization done |
| 406 |
Initialization done- block initialization is complete. |
| 407 |
Not selected |
| 408 |
Not selected- target value provided by block was not selected. |
| 409 |
No path |
| 410 |
No path- there is no path to the process. |
| 411 |
Fail |
| 412 |
Fail- hardware failure. |
| 413 |
Bad |
| 414 |
Bad- block is out of service or has bad input. |
| 415 |
Not from process |
| 416 |
Not from process- value is not directly affected by any process information. |
| 417 |
Local override |
| 418 |
Local override- block has LO mode. |
| 419 |
Not Cascade Mode |
| 420 |
Not RCas Mode |
| 421 |
Not ROut Mode |
| 422 |
No communication |
| 423 |
No communication- (NO_COM). |
| 424 |
uint16_var_blk_char |
| 425 |
uint32_var_blk_char |
| 426 |
uint8_var_blk_char |
| 427 |
int8_var_blk_char |
| 428 |
new itest redef1 label |