Device dictionary

Loading…

Reference ID	String
0	Model RX5
1	MAGNETROL
2	Device ID
3	Poll Address
4	Faults
5	Faults indicate a defect or failure of the device or other conditions that preclude reliable measurement. Currently occuring conditions can be viewed from the Status menu; historical information can be viewed from the Diagnostic Info menu.
6	Echo Lost
7	Echo Lost - Target peak cannot be found.
8	Safety Zone Alrm
9	Safety Zone Alarm - Level is within the Safety Zone. Modify SZ Alarm parameters if not operating to expectations.
10	No Fiducial
11	No Fiducial - Cannot find valid fiducial signal. Ensure transmitter/antenna connector is tight; consult Factory if problem persists.
12	Default Paramtrs
13	Default Paramtrs - The application configuration information has been reset to default values. Please reconfigure the instrument.
14	Software Error
15	Software Error - Software algorithms corrupted; consult Factory if problem persists.
16	EE Write Failure
17	EE Write Failure - EEPROM Write failure; consult Factory if problem persists.
18	EE Read Failure
19	EE Read Failure - EEPROM Read failure; consult Factory if problem persists.
20	CPU Failure
21	CPU Failure - Microprocessor failure; consult Factory if problem persists.
22	Warnings
23	Warning messages indicate conditions that are not fatal but may affect measurement. Currently occuring conditions can be viewed from the Status menu; historical information can be viewed from the Diagnostic Info menu.
24	Factory Cal Reqd
25	Factory Cal Required - The Pulsar electronics require re-calibration by Magnetrol. The instrument will continue to operate at reduced accuracy.
26	Fiducial Unclear
27	Fiducial Unclear - Fiducial signal quality is questionable. Ensure that transmitter/antenna connector is tight; consult Factory if problem persists.
28	Corrupt Targ Rej
29	Corrupt Target Rejection - Invalid False Target Rejection data, re-run False Target Rejection routine; consult Factory if problem persists.
30	No Fals Targ Rej
31	No False Target Rejection - False Target Rejection has not been run or was manually disabled, re-run False Target Rejection routine or manually enable.
32	Button Failure
33	Button Failure - One or more of the buttons (Up, Down, or Enter keys) is stuck closed.
34	Warning 04
35
36	Warning 02
37	Warning 01
38	Trim Loop Current
39	Loop Test
40	Level of material in vessel
41	Loop
42	%Output
43	20mA Set Point
44	4mA Set Point
45	Target Rej Status
46	Antenna Type
47	Antenna Extension
48	Units
49	.1f
50	.2f
51	.3f
52	Level
53	5.1f
54	%
55	Distance
56	Distance measurement includes Sensor Offset value.
57	2u
58	Quality
59	Quality of signal reflection, best values are between 20 and 90.
60	4.3f
61	V
62	Echo Amplitude
63	Factory parameter, displayed for diagnostic purposes only.
64	ROC per minute
65	3u
66	Scatter
67	Rate
68	Sensor Offset
69	Sensor Offset is the distance (+ or -) from the sensor reference point (bottom of NPT thread or flange face, top of BSP thread) to the top of the tank.
70	Level Offset
71	Level Offset defines an area at the bottom of the vessel where reflections cannot be measured effectively due to angled bottoms or obstructions. It is the distance from the bottom of the tank to the lowest valid level reading. Level reading will never be lower than Level Offset value.
72	Damping
73	A damping factor (0-45) may be added to smooth a noisy display and/or output due to turbulence.
74	4.1f
75	Damping Time Constant
76	Damping Time Constant is not applicable for this device.
77	Pipe ID
78	Inside Diameter of standpipe or stillwell pipe. Enter 0 if Antenna is not installed in a pipe.
79	5.2f
80	Analog output loop current
81	3.6mA
82	22mA
83	Hold
84	System Fault State
85	System Fault State defines how the Analog Output will respond when the transmitter detects a system fault.
86	LOE Fault State
87	LOE Fault State defines how the Analog Output will respond when the transmitter detects a Loss of Echo fault.
88	None
89	Latch3.6
90	Latch 22
91	SZ Fault State
92	Safety Zone Fault State defines how the Analog Output will respond when the transmitter detects a level that is within the Safety Zone which is a user defined area just below the Blocking Distance. Enable fault if necessary to ensure safe, reliable high-level readings in critical applications. If Latch3.6 or Latch22 is chosen, the unit will remain in alarm until it is manually cleared with the SZ Alarm Reset.
93	s
94	LOE Delay
95	Loss of Echo Delay, valid values are 0 to 255 seconds.
96	SZ Height
97	Safety Zone Height - Enter a distance that develops a safety zone just below the Blocking Distance. The transmitter will report a Safety Zone Fault if the level rises into this area.
98	RAA-A***
99	Teflon Rod, SS
100	RAA-B***
101	Teflon Rod, Hastelloy
102	RAA-C***
103	Teflon Rod, Monel
104	RAA-3***
105	Teflon Rod, Kynar
106	RAB-A***
107	Polypropylene Rod, SS
108	RAB-B***
109	Polypropylene Rod, Hastelloy
110	RAB-C***
111	Polypropylene Rod, Monel
112	RAB-3***
113	Polypropylene Rod, Kynar
114	RA4-A***
115	4" (100mm) Horn, SS
116	RA4-B***
117	4" (100mm) Horn, Hastelloy
118	RA4-K***
119	4" (100mm) Horn, 316SS (B31.1, B31.3)
120	RA6-A***
121	6" (150mm) Horn, SS
122	RA6-B***
123	6" (150mm) Horn, Hastelloy
124	RA6-K***
125	6" (150mm) Horn, 316SS (B31.1, B31.3)
126	RAA-K***
127	Teflon Rod, 316SS (B31.1, B31.3)
128	RAB-G***
129	All-polypropylene wetted surfaces; Rod
130	RAB-K***
131	Polypropylene Rod, 316SS (B31.1, B31.3)
132	RAB-L***
133	All-polypropylene wetted surfaces; Rod (B31.1, B31.3)
134	RA3-A***
135	3" (75mm) Horn
136	RA8-A***
137	8" (200mm) Horn
138	RAK-A***
139	2" (50mm) Stillwell Antenna, Teflon, 316SS
140	Type 21
141	Type 22
142	Type 23
143	Type 24
144	Antenna
145	Antenna Type - Select the first 7 digits of the Antenna Model Number (first 4 are significant). Information is located on the nameplate mounted on the antenna.
146	-0**
147	Nozzle length <= 3" (80mm)
148	-1**
149	Nozzle length <= 4" (100mm)
150	-2**
151	Nozzle length <= 8" (200mm)
152	-3**
153	Nozzle length <= 12" (300mm)
154	Extension
155	Antenna Extension - Select the last three digits of the Antenna Model Number corresponding to the Antenna Extension. Information is located on the nameplate mounted on the antenna.
156	NPT
157	BSP
158	Flange
159	Antenna Mount
160	Type of Antenna Mounting
161	2 XP
162	1 IS
163	Launcher
164	1.7 - 3
165	3 - 10
166	10 - 100
167	Dielectric
168	Select the dielectric range of the medium.
169	None
170	Light
171	Medium
172	Heavy
173	Turbulence
174	Increase choice if Quality value is consistently < 20.
175	< 5 in/min
176	5-20 in/min
177	20-60 in/min
178	> 60 in/min
179	< 13 cm/min
180	13-50 cm/min
181	50-150 cm/min
182	> 150 cm/min
183	Rate of Change
184	Select the Maximum rate of change of the level surface (rising or falling).
185	Foam
186	Increase choice if Quality value is consistently < 20.
187	Flat
188	HorizCyl
189	Dome
190	Irregular
191	Other
192	Tank Top
193	Select the metallic tank top structure (choose Other for non-metalic tanks).
194	Tank Height
195	Distance from the bottom to the top of tank.
196	Trim Level
197	Trim Level is an offset value to be used to force the transmitter to output the exact Level. This should only be used after all parameters have been entered correctly, Tank Height and Sensor Offset have been confirmed accurate, and it has been confirmed that the transmitter is tracking the correct level target.
198	Blocking Distance
199	Blocking Distance defines an area near the antenna where reflections cannot be measured effectively due to antenna ringing. It is measured from the sensor reference point (bottom of NPT thread or flange face, top of BSP thread). Level reading will never be higher than level corresponding to Blocking Distance value. Do not allow liquid onto the antenna.
200	Date/Time/Initials
201	When and by whom calibration was performed.
202	Enter Password
203	Password is required for adjusting Factory Settings.
204	New User Password
205	User password required to change parameter settings from keypad.
206	Magnetrol S/N
207	Serial number of this transmitter
208	4u
209	4mA Trim Value
210	20mA Trim Value
211	Firmware Version
212	Processor firmware revision level
213	Coprocessor Version
214	Coprocessor firmware revision level
215	Range
216	mm
217	Distance Corr
218	dm/s
219	Ceff
220	CF #Run Average
221	Conversion Factor
222	4i
223	Scale Offset
224	Best
225	First
226	H/Dist
227	Algorithm
228	Sqrt
229	Linear
230	Const
231	Step
232	TVG Type
233	TVG Max
234	Fiducial Position
235	Fiducial Gain
236	System Gain
237	1
238	2
239	4
240	8
241	16
242	32
243	64
244	128
245	#Run Average
246	Accurate
247	Robust
248	Adaptive Filter
249	#Adaptive Average
250	Scatter High Limit
251	Rate High Limit
252	2%
253	5%
254	11%
255	16%
256	25%
257	44%
258	20 mV
259	50 mV
260	110 mV
261	160 mV
262	250 mV
263	440 mV
264	Peak Detect Thresh
265	PeakMax
266	Fixed
267	Peak Detect Ref
268	V
269	Min Threshold
270	mm/min
271	Max Rate
272	Max Delta Distance
273	ES Delay
274	SZ Hysteresis
275	Auto
276	42m@10s
277	4.2h@1m
278	42h@10m
279	4.2d@1h
280	31.5d@3h
281	Never
282	DataLog
283	FactPar1
284	FactPar2
285	Informational
286	Informational messages indicate conditions that are not critical to measurement. Currently occuring conditions can be viewed from the Status menu; historical information can be viewed from the Diagnostic Info menu.
287	Tank Dim Invld
288	Tank Dimensions Invalid - Tank dimensions exceed maximum range of the transmitter; reduce tank height and/or Sensor Offset values.
289	Signal Too Low
290	Signal Too Low - Level signal amplitude is insufficient; choose lower Dielectric range, increase Turbulence or Foam settings, consult Factory if problem persists.
291	Signal Too Hi
292	Signal Too High - Level signal amplitude is excessive; choose higher Dielectric range, reduce Turbulence or Foam settings, consult Factory if problem persists.
293	DC Noise
294	DC Noise - Excessive noise on A/D channel; consult Factory.
295	Uncertn Target
296	Uncertain Target - Target is missing, but not determined to be lost; device is holding last valid value while confirming the target position, will continue based upon the LOE Delay value, consult Factory if problem persists.
297	Scatter Target
298	Scattered Target - Return signals scattered due to turbulence in vessel.
299	Incmp Targ Rej
300	Incomplete Target Rejection - False target only partially captured; re-run False Target Rejection routine.
301	IPC Ack
302	IPC Ack - Internal communications error; consult Factory.
303	IPC Length
304	IPC Length - Internal communications error; consult Factory.
305	IPC Checksum
306	IPC Checksum - Internal communications error; consult Factory.
307	IPC Bus
308	IPC Bus - Internal communications error; consult Factory.
309	MultiEcho Dbl
310	MultiEcho Trpl
311	Info 0800
312	Info 0010
313	Info 0008
314	OFF
315	ON
316	Level
317	Mode
318	Review all Targets detected by the transmitter including false targets (targets other than Level). Ensure that the proper Level target is shown then run Target Rejection routine. If reported Level is close to actual and the quality number is > 20, it is probably correct. Targets can be viewed in Level or Distance mode.
319	Main Menu
320	Device Setup
321	Calibration
322	Basic Setup
323	Advanced Setup
324	Diagnostics
325	Factory Settings
326	Targets
327	Peaks
328	Target Rejection
329	Select
330	Status
331	Diagnostic Info
332	Informational
333	Review
334	Enabled
335	Disabled
336	The Target Rejection routine detects, stores, and cancels false targets to ensure detection of the proper level signal. The No False Target Rejection warning message will be displayed if this algorithm is not enabled. Do not proceed with False Target Rejection procedure until confirming Level and Quality values in Targets menu. False Target Rejection should be run with vessel at or near empty when all targets are exposed; re-run this routine if initial calibration is done with significant liquid in vessel. The false target profile will be disabled and this routine should be re-run if antenna or tank parameters are modified or when launcher is repositioned.
337	Empty
338	Partial
339	Target Rej Type
340	Targ Rej Level
341	Req Disable
342	Req Enable
343	Req Empty
344	Req Partial
345	Partial TP Peaks
346	Target Peaks
347	Diagnostic Peaks
348	Target1 Quality
349	Target2 Quality
350	Target3 Quality
351	Target4 Quality
352	Target5 Quality
353	Target6 Quality
354	Target7 Quality
355	Target8 Quality
356	Target9 Quality
357	Target1
358	Target2
359	Target3
360	Target4
361	Target5
362	Target6
363	Target7
364	Target8
365	Target9
366	Peak0 Quality
367	Peak1 Quality
368	Peak2 Quality
369	Peak3 Quality
370	Peak4 Quality
371	Peak5 Quality
372	Peak6 Quality
373	Peak7 Quality
374	Peak8 Quality
375	Peak9 Quality
376	Peak0
377	ms
378	Peak1
379	Peak2
380	Peak3
381	Peak4
382	Peak5
383	Peak6
384	Peak7
385	Peak8
386	Peak9
387	SZ Alarm Reset
388	Clear a latched Safety Zone Alarm
389	Clear
390	Clear persistent stored errors.
391	Enable
392	Target Rejection is already enabled, select Empty or Partial to re-run Target Rejection routine.
393	Enables previously run Empty Target Rejection profile
394	Enables previously run Partial Target Rejection profile
395	No valid Target Rejection profile exists, select Empty or Partial to run Target Rejection routine.
396	Disable
397	Disables previously run Empty Target Rejection profile.
398	Disables previously run Partial Target Rejection profile.
399	Target Rejection is already disabled.
400	->Empty
401	Target Rejection routine for Empty tanks; false targets in entire tank will stored and canceled.
402	->Partial
403	Target Rejection routine for Partially full tanks. If Partial is chosen multiple Level targets may be offered; choose the target that represents the actual Level, other targets will be cancelled. If correct level is not offered, ensure that tank dimensional information is correct. If level cannot be found, choose Enter Level, then enter the correct level value.
404	Mode
405	FMU860
406	DT
407	DVC
408	FCX
409	AS800
410	340T
411	340C
412	344
413	Siemens Micro K
414	SITRANS L
415	SIPAN PH
416	SITRANS P
417	75SMT
418	UNIDELTA
419	8320
420	SX5100
421	TSV175
422	DMU
423	3780
424	BM70
425	8u
426	Are You Sure?
427	No;Yes
428	Measuring.
429	Measuring..
430	Measuring...
431	Measuring....
432	Measuring.....
433	Measuring......
434	Saving...
435	Too many peaks!
436	No Peaks
437	Level %{i} %{2} %{0}, Quality %{1} ?
438	Enter Level?
439	Enter Level in %{0}
440	Level Too High!
441	Saving...
442	Select Targets Mode
Reference ID	String