Device dictionary

Loading…

Reference ID	String
0	Model 705 2.x
1	MAGNETROL
2	Device ID
3	Poll Address
4	Faults
5	Default Paramtrs
6	Default Parameters - Non-volatile memory contents have been overwritten with default values. Please re-enter application parameters through Calibration and Basic Setup menus.
7	No Fiducial
8	No Fiducial Pulse - Check connection between circuit boards in module.
9	No Level Signal
10	Missing Level Signal - Check probe connection and application parameters.
11	Bad Cal Paramtrs
12	Bad Calibration Paramters - Check that the correct probe length has been entered.
13	Fault 3
14	Available for additional fault identification.
15	Fault 2
16	reserved
17	Not available for fault identification.
18	Warnings
19	Factory Cal Reqd
20	Factory Calibration required - The module requires re-calibration by the factory. The instrument will continue to operate at reduced accuracy.
21	ICF1 State Error
22	Device in unknown state when input capture interrupt occurred.
23	OCF1 State Error
24	Device in unknown state when output compare interrupt occurred.
25	ICF2 Interrupt
26	Spurious input capture interrupt occurred.
27	OCF2 Interrupt
28	Spurious output compare interrupt occurred.
29	Ovrflw Interrupt
30	Unexpected timer overflow interrupt has occurred.
31	Extern Interrupt
32	Unexpected external interrupt has occurred.
33	Sfwr Interrupt
34	Unexpected software interrupt has occurred.
35	Trim 4 and 20
36	Loop Test
37	Units
38	6.1f
39	Level of material in vessel
40	5.1f
41	%
42	% Output
43	Minimum Span
44	Upper Range Limit
45	Lower Range Limit
46	4.1f
47	Damping
48	5.2f
49	Loop
50	Analog output loop current
51	Alarms
52	7xA_x
53	7xA: Coaxial Probe (dielectric range >= 1.7)
54	7xB_x
55	7xB: Rigid Twin Rod Probe (dielectric range >= 2.0)
56	7xD_x
57	7xD: High Temperature-High Pressure Coaxial Probe (dielectric range >= 2.0)
58	7xP_x
59	7xP: High Pressure Coaxial Probe (dielectric range >= 1.7)
60	7xR_x
61	7xR: Coaxial Probe for flooding applications (dielectric range >= 1.7)
62	7xS_x
63	7xS: High Temperature-High Pressure Coaxial Probe for steam
64	7xU_x
65	7xU_x: Coaxial Probe for cryogenic liquids (dielectric range >= 1.7)
66	7x7_x
67	7x7: Flexible Twin Rod Probe (dielectric range >= 2.0)
68	Type 9
69	Type 10
70	Type 11
71	Type 12
72	Type 13
73	Type 14
74	Type 15
75	Type of probe connected to transmitter
76	Probe Type
77	NPT
78	US National tapered Pipe Thread
79	BSP
80	British Straight Pipe Thread
81	Flange
82	Welded ANSI or DIN Flange
83	Mounting style of probe fitting
84	Probe Mount
85	Distance from face of process seal to end of probe
86	Probe Length
87	Probe Offset
88	Desired level reading when liquid surface is at end of probe
89	1.7 - 3
90	Dielectric constant of material lies between 1.7 and 3
91	3 - 10
92	Dielectric constant of material lies between 3 and 10
93	10 - 100
94	Dielectric constant of material lies between 10 and 100
95	1.4 - 1.7
96	Dielectric constant of material lies between 1.4 and 1.7
97	Dielectric
98	Dielectric constant of material in vessel
99	4mA Set Point
100	20mA Set Point
101	3.6mA
102	22mA
103	Hold
104	Fault State
105	Date/Time/Initials
106	When and by whom calibration was performed
107	3u
108	Enter Password
109	Password is required for adjusting Advanced Setup parameters Magnetrol S/N and Device id, and Factory Settings parameters Window, Range, Gain, Conversion Factor, Scale Offset, and Target Calibration for 7xS Probe.
110	Magnetrol S/N
111	Factory parameter, displayed for diagnostic purposes only
112	8u
113	New User Password
114	User password required to change parameter settings from keypad
115	4u
116	Ticks
117	Fiducial Ticks
118	<Window>
119	Range
120	Gain
121	Conversion Factor
122	4i
123	Scale Offset
124	5d
125	7xS Derating Fct
126	Run
127	Cal
128	7xS Oper Mode
129	7xS Target Ticks
130	7xS Target Ratio
131	7xS Target Gain
132	7xS Targ Cal Tks
133	CFD
134	Fixed
135	Threshold
136	Use 'CFD' except in situation with low dielectric (< 3) material over higher dielectric (> 10) material, e.g., oil over water, in which case use 'Fixed'.
137	# of Ticks
138	Damped time of flight. Factory parameter, displayed for diagnostic purposes only
139	4mA Trim Value
140	20mA Trim Value
141	Firmware Version
142	Main Menu
143	Device Setup
144	Basic Setup
145	Advanced Setup
146	Diagnostics
147	Factory Settings
148	Review
149	7xS Target Calib
150	Captures time-of-flight to target on 7xS probe at room ambient.
151	Targ Cal Abort
152	No Target detected and/or Probe not dry
153	Elapsed Time
154	04d
155	sec(-ive) hrs(+ive)
156	Elapsed time since most recent significant event.
157	Event status
158	ALL FAULTS CLEARED
159	POWER ON
160	DEFAULT PARAMETERS
161	BAD CAL PARAMETERS
162	DEFAULT PARAMETERS++
163	NO LEVEL SIGNAL
164	NO LEVEL SIGNAL++
165	NO FIDUCIAL SIGNAL
166	DEFAULT PARAMETERS+
167	NO FIDUCIAL SIGNAL+
168	NO FIDUCIAL SIGNAL++
169	DEFAULT PARAMTERS+++
170	Bit encoded event status stored in log.
171	Event Interval
172	05i
173	Interval associated with a particular event that is the time elapsed since the previous event.
174	No earlier event
175	No later event
176	Display Event Log
177	Displays history of significant events such as Power On, Faults, and All Faults Cleared. The time interval displayed with a particular event is the time elapsed since the previous event. The interval associated with a Power On event is always 0.
178
179	% Out
180
181	FMU860
182	DT
183	DVC
184	FCX
185	AS800
186	340T
187	340C
188	344
189	Siemens Micro K
190	SITRANS L
191	SIPAN PH
192	SITRANS P
193	75SMT
194	UNIDELTA
195	8320
196	SX5100
197	TSV175
198	DMU
199	3780
200	BM70
201	Target Ticks =%[4i]{0}
202	Calibration ok Set Targ Air =%[4i]{0}?
203	Calibration bad TargTks unstable
204	Interval since most recent event: %[.4d]{fault_status_age} secs
205	Interval since most recent event: %[.4d]{fault_status_age} hrs
206	Event log empty
207	Event: %{0} Interval: %[.4d]{interval_secs} secs
208	Get earlier event;Get later event
209	Event: %{0} Interval: %[.4d]{1} hrs
Reference ID	String