| 0 |
SI792D |
| 1 |
HACH_LANGE |
| 2 |
Address |
| 3 |
Tag |
| 4 |
Descriptor |
| 5 |
Message |
| 6 |
Date |
| 7 |
Assembly Num |
| 8 |
Error Status |
| 9 |
Field Device Error Status- Failure messages of the Field Device are listed |
| 10 |
Err 01 SAT Value |
| 11 |
Err 02 Conc Val |
| 12 |
Err 03 Temp Val. |
| 13 |
Err 11 I < 3.8mA |
| 14 |
Err 12 I >20.5mA |
| 15 |
Err 13 Loop Span |
| 16 |
Err 98 Conf Data |
| 17 |
Err 99 Data Lost |
| 18 |
Smiley Earnest |
| 19 |
Smiley Earnest - Maintance required. Sensoface provides information on wear and required maintance. However, device continues operation with diminished accuracy. |
| 20 |
Response time |
| 21 |
Cal. timer > 80% |
| 22 |
Zero point |
| 23 |
Slope |
| 24 |
Smiley Sad |
| 25 |
Smiley Sad - Correct measurment is no longer ensured. Sensoface provides information on wear and required maintance. However, device continues operation with seriously diminished accuracy. |
| 26 |
Response time |
| 27 |
Cal. timer >100% |
| 28 |
Err 33 |
| 29 |
Zero point limit |
| 30 |
Slope limit |
| 31 |
Temp SAT/Conc |
| 32 |
Analog Out Sat. |
| 33 |
HOLD Mode |
| 34 |
Analog Outputs of the Field Device are fixed in HOLD mode. The analog and digital Outputs remain unchanged. |
| 35 |
Resp. Preambles |
| 36 |
Device Status |
| 37 |
Device status and mode |
| 38 |
Configuration |
| 39 |
Calibration |
| 40 |
Sample was taken |
| 41 |
Online |
| 42 |
Process Variables |
| 43 |
Diagnosis |
| 44 |
Device Info |
| 45 |
Conf: Output |
| 46 |
Conf: Temp. Comp. |
| 47 |
Conf: Correction |
| 48 |
Conf: Calibration |
| 49 |
Conf: Alarm Setup |
| 50 |
Service |
| 51 |
Review |
| 52 |
Review: Conf/Cal |
| 53 |
Review: Dev. Info |
| 54 |
Upload Variables |
| 55 |
Dummy1Byte |
| 56 |
Dummy4Byte |
| 57 |
Sel. Code Index |
| 58 |
|
| 59 |
Sel. Codes |
| 60 |
Input Sel. Code |
| 61 |
Calib. Sel. Code |
| 62 |
Output Sel. Code |
| 63 |
Temp Sel. Code |
| 64 |
Conf.4 Sel. Code |
| 65 |
Invalid Unit Code |
| 66 |
Busy |
| 67 |
22mA on Error |
| 68 |
Switch 22mA signal for error message on or off |
| 69 |
Off |
| 70 |
On |
| 71 |
HOLD Last/Fix |
| 72 |
The output current behavior in the HOLD mode can be specified. Last- The output current is frozen at its last value, Fix- A constant value from 3.8mA to 22mA |
| 73 |
Last Value |
| 74 |
Fixed Value |
| 75 |
Sensocheck |
| 76 |
Sensocheck continously monitors the sensor |
| 77 |
Alarm LED Hold |
| 78 |
Alarm LED Hold:
Para. Alarm Hold
------------------
on : on flash
off : flash off |
| 79 |
PV unit |
| 80 |
Select the PV Unit |
| 81 |
% |
| 82 |
µg/l |
| 83 |
g/l |
| 84 |
ppb |
| 85 |
ppm |
| 86 |
Meas function |
| 87 |
DO |
| 88 |
GAS |
| 89 |
Sensor type |
| 90 |
Typ A |
| 91 |
Typ B |
| 92 |
press medium |
| 93 |
BAR |
| 94 |
KPA |
| 95 |
PSI |
| 96 |
cal mode |
| 97 |
Conc |
| 98 |
Sat |
| 99 |
Temp. unit |
| 100 |
°C |
| 101 |
°F |
| 102 |
Sensor |
| 103 |
NTC22k |
| 104 |
NTC30k |
| 105 |
PV Unit |
| 106 |
ugl |
| 107 |
5.2f |
| 108 |
5.5f |
| 109 |
4.0f |
| 110 |
5.1f |
| 111 |
PV USL |
| 112 |
PV LSL |
| 113 |
Min. Span |
| 114 |
PV AO |
| 115 |
mA |
| 116 |
4.1f |
| 117 |
PV % |
| 118 |
You can choose the kind of dependence of the current from the digital value |
| 119 |
7.5f |
| 120 |
5.3f |
| 121 |
Number |
| 122 |
SV |
| 123 |
Temperature of process medium temperature compensation |
| 124 |
The specified temperature unit |
| 125 |
SV USV |
| 126 |
SV LSV |
| 127 |
SV Min. Span |
| 128 |
SAT |
| 129 |
Percent Saturation value |
| 130 |
4.2f |
| 131 |
Concentration value |
| 132 |
Temp. |
| 133 |
Temperature for process medium temperature compensation |
| 134 |
Sensor input current |
| 135 |
Press(mbar) |
| 136 |
The Preasure for measurement in mbar |
| 137 |
3.1f |
| 138 |
Pressure (cal) |
| 139 |
The Preasure for calibration |
| 140 |
mbar |
| 141 |
The Calibration generates the electrode parameters. You can also directly enter the slope of an electrode |
| 142 |
9.6f |
| 143 |
Zeropoint |
| 144 |
The Calibration generates the electrode parameters. You can also directly enter the zeropoint of an electrode |
| 145 |
Cal.Timer |
| 146 |
Calibration timer interval. 0 = cal time switched off |
| 147 |
h |
| 148 |
04.0f |
| 149 |
Cal. Mode |
| 150 |
Selected Calibration Mode |
| 151 |
Sal. Corr |
| 152 |
Salinity correction ppt(parts per thousand) - corresponds to g/kg |
| 153 |
rel. humidity |
| 154 |
relative humidity |
| 155 |
02.0f |
| 156 |
2.0f |
| 157 |
HOLD Fix Value |
| 158 |
Specify fixed output current in HOLD mode |
| 159 |
pol.Volt |
| 160 |
polarisation voltage for sensor |
| 161 |
mV |
| 162 |
5.0f |
| 163 |
Sample |
| 164 |
Calibration with Sampling to determine the electrode zero point |
| 165 |
Output Filter |
| 166 |
Time constant of output filter |
| 167 |
s |
| 168 |
3.0f |
| 169 |
Alarm Delay |
| 170 |
Alarm delay time of alarm signal |
| 171 |
Filtertime of output current |
| 172 |
Process Medium / PV unit |
| 173 |
Select the Process Medium |
| 174 |
Temp. Unit |
| 175 |
Select the temperature unit |
| 176 |
Temp. Probe |
| 177 |
Select the temperature probe type |
| 178 |
Pressure |
| 179 |
Select the Pressure-Unit and enter the Pressure-value |
| 180 |
Self Test |
| 181 |
Performs transmitter self test |
| 182 |
Master Reset |
| 183 |
Performs master reset in the Field Device |
| 184 |
Conf Changed Reset |
| 185 |
Performs reset of configuration changed sign in the Field Device |
| 186 |
Loop Test |
| 187 |
Take Sample |
| 188 |
Sample Calibration Sequence Take Sample |
| 189 |
Input Lab Sample |
| 190 |
Sample Calibration Sequence Input Lab Sample |
| 191 |
FMU860 |
| 192 |
DT |
| 193 |
DVC |
| 194 |
FCX |
| 195 |
AS800 |
| 196 |
340T |
| 197 |
340C |
| 198 |
344 |
| 199 |
Siemens Micro K |
| 200 |
SITRANS L |
| 201 |
SIPAN PH |
| 202 |
SITRANS P |
| 203 |
75SMT |
| 204 |
UNIDELTA |
| 205 |
8320 |
| 206 |
SX5100 |
| 207 |
TSV175 |
| 208 |
DMU |
| 209 |
3780 |
| 210 |
BM70 |
| 211 |
8u |
| 212 |
Sample calibration via HART not available for device software before V1.0.
Press OK to finish |
| 213 |
WARNING: Configuration was abborted!
ACTION: Repeat this step. |
| 214 |
Actually: %{0} please wait |
| 215 |
Process Medium |
| 216 |
DO;GAS |
| 217 |
%;µg/l;g/l;ppb;ppm |
| 218 |
%;ppm |
| 219 |
Enter lower range value: |
| 220 |
Enter upper range value: |
| 221 |
configured values:
PV unit: %{0}
lower range value: %{1} %{0}
upper range value: %{2} %{0} |
| 222 |
Off;On |
| 223 |
°C;°F |
| 224 |
NTC22k;NTC30k |
| 225 |
Last Value;Fixed Value |
| 226 |
Select Press Unit: |
| 227 |
Enter Pressure: |
| 228 |
fval |
| 229 |
Press OK to perform transmitter self test |
| 230 |
Self test is running please wait: %{sec} s |
| 231 |
Press OK to perform master reset |
| 232 |
Master reset is running please wait: %{sec} s |
| 233 |
Press OK to reset configuration changed sign |
| 234 |
Take a sample from the process and store the currently measured value. |
| 235 |
Note that the meassured value of the sample is temperature dependent. |
| 236 |
As far as possible, you should transport the sample in an insulated container (Dewar). |
| 237 |
The meassured value may also be altered due to escaping of volatile substances. |
| 238 |
WARNING: Device is in calibration or configuration, no sample calibration allowed! |
| 239 |
ACTION: Leave device calibration or configuration and repeat this step. |
| 240 |
WARNING: Sample was already taken. If you call <Take Sample> twice then the first sample will be lost! |
| 241 |
Press Abort to keep the first sample |
| 242 |
Last measured value:
%{0} %{1}
%{2} %{3}
Press OK to take calibration sample |
| 243 |
WARNING: Sample calibration was abborted!
ACTION: Repeat this step. |
| 244 |
Enter the measured lab value. The new zero point is automatically calculated and stored. |
| 245 |
The values obtained by sample calibration are always accepted, even if they are outside calibration limits! |
| 246 |
WARNING: No sample was taken, no sample calibration allowed! |
| 247 |
ACTION: First call <Take Sample> and then <Input Lab Sample>. |
| 248 |
Enter the comparison lab value : |