Device dictionary

Loading…

Reference ID	String
0	NAx600sc Sodium
1	HACH LANGE GmbH
2	Temperature Error
3	Sample Warning
4	? CAL Warning
5	? Meas. Warning
6	Safety Warning
7	Reagent Warning
8	Maint. Required Warning
9	Meas. CAL Error
10	Electronic Adjustment Error
11	Cleaning Error
12	Measuring Module Error
13	Re-initialization Error
14	Hardware Error
15	Internal COMM Error
16	Humidity Error
17	FLASH FAILURE
18	FIRMWARE ERROR
19	HARDWARE ERROR
20	KCL SOL EMPTY
21	REACT SOL EMPTY
22	END OF PROGNOSYS TRIAL
23	PROGNOSYS TRIAL
24	OVERFEED TIMER
25	RESTART TO ACCEPT SW
26	NETWORK COMM LOSS
27	CALIBRATION P0 TOO HIGH
28	CALIBRATION P2 < 5X P1
29	STABLIZER ERROR
30	PH TOO LOW
31	SAMPLE FLOW HIGH
32	REACT VOLTAGE LOW
33	CONDITION SOL EMPTY
34	CAL STD SOL EMPTY
35	REACT SOL LOW
36	SAMPLE FLOW LOW
37	CONDITION SOL LOW
38	CALIBRATION FAIL
39	SHUTDOWN
40	AUTO CAL DISABLED
41	SETUP REQUIRED
42	AUTO REACT DISABLED
43	SAMPLE 1 MISSING
44	SAMPLE 2 MISSING
45	SAMPLE 3 MISSING
46	SAMPLE 4 MISSING
47	SAMPLE TEMP LOW
48	SAMPLE TEMP HIGH
49	KCL SOL LOW
50	CAL STD LOW
51	9.3f
52	Ch1 Sod. Conc.
53	Ch2 Sod. Conc.
54	Ch3 Sod. Conc.
55	Ch4 Sod. Conc.
56	Ch1 Sodium Concentration
57	Sodium Conc Unit
58	Sodium Conc Value
59	Ch1 Sodium Conc USL
60	Ch1 Sodium Conc LSL
61	Ch1 Sodium Conc Min Span
62	Ch1 Sodium Conc Damping
63	Sodium Conc Class
64	Sodium Conc Data Quality
65	Sodium Conc Limit Status
66	Sodium Conc Family Status
67	Sodium Analyzer S/N
68	Ch2 Sodium Concentration
69	Ch2 Sodium Conc USL
70	Ch2 Sodium Conc LSL
71	Ch2 Sodium Conc Min Span
72	Ch2 Sodium Conc Damping
73	Ch3 Sodium Concentration
74	Ch3 Sodium Conc USL
75	Ch3 Sodium Conc LSL
76	Ch3 Sodium Conc Min Span
77	Ch3 Sodium Conc Damping
78	Ch4 Sodium Concentration
79	Ch4 Sodium Conc USL
80	Ch4 Sodium Conc LSL
81	Ch4 Sodium Conc Min Span
82	Ch4 Sodium Conc Damping
83	Ch1 Conc Unit
84	The Ch1 Measured Sodium Concentration Unit.
85	ppm
86	ppb
87	mg/L
88	ug/L
89	The measured value of Ch1 Sodium Concentration.
90	Ch2 Conc Unit
91	The Ch2 Measured Sodium Concentration Unit.
92	The measured value of Ch2 Sodium Concentration.
93	Ch3 Conc Unit
94	The Ch3 Measured Sodium Concentration Unit.
95	The measured value of Ch3 Sodium Concentration.
96	Ch4 Conc Unit
97	The Ch4 Measured Sodium Concentration Unit.
98	The measured value of Ch4 Sodium Concentration.
99	PV Class
100	PV Data Quality
101	PV Limit Status
102	PV Family Status
103	PV Sensor S/N
104	8d
105	ACTIVE SLOPE
106	Active slope value.
107	5.1f
108	ACTIVE OFFSET
109	Active offset value.
110	6.1f
111	TARGET PH
112	Target pH setting.
113	5.2f
114	SlaveSwVersion
115	Slave firmware revision.
116	COMPENSATED POTENTIAL
117	E25 temperature compensated mV.
118	mV
119	the sodium concentration of channel 1
120	the sodium concentration of channel 2
121	the sodium concentration of channel 3
122	the sodium concentration of channel 4
123	MeasUnits
124	Measure units.
125	AutoReactEnable
126	Auto reactivation enable/disable setting.
127	NO
128	YES
129	SCRIPT VERSION
130	SCRIPT VERSION.
131	3d
132	SCRIPT CONTENT
133	SCRIPT CONTENT.
134	SignalAverage
135	The signal average.
136	1d
137	CurMeasChannel
138	The index of current measuring channel.
139	ActivateChannels
140	The Activated measurement channels.
141	2d
142	NumChannels
143	Number Of Total Measurement Channels.
144	ONE CHANNEL
145	TWO CHANNELS
146	FOUR CHANNELS
147	MEAS INDICATOR
148	The measurement quality indicator
149	%
150	SERVICE IN DAY
151	service in day.
152	days
153	Output Mode
154	Output Mode.
155	Normal Operation
156	Active Outputs
157	Hold Outputs
158	Transfer Value
159	ProcessEvents
160	Process Event.
161	MEASURING 1...
162	MEASURING 2...
163	MEASURING 3...
164	MEASURING 4...
165	CALIBRATE
166	STARTUP
167	GRAB SAMPLE/VERIFICATION
168	MARK END OF MEASURE
169	Location String
170	Location or Name of Module.
171	Appl. Code Ver.
172	Application Code Version times 100.
173	Boot Code Ver.
174	Boot Code Version times 100.
175	Module S/N
176	Module serial number.
177	Classified Status 1
178	Status Flags for Measurements 0-3.
179	CAL in Progress
180	The device has been placed in a calibration mode. The measurements may not be valid.
181	Cleaning In Progress
182	The device has been placed in a cleaning mode. The measurements may not be valid.
183	Service/Maint. Menu
184	The device has been placed in a service or maintenance mode in which the measurements may not be valid.
185	Common Error
186	Meas. 0 Quality Bad
187	Meas. 0 Low Limit
188	Meas. 0 High Limit
189	Meas. 1 Quality Bad
190	Meas. 1 Low Limit
191	Meas. 1 High Limit
192	Meas. 2 Quality Bad
193	Meas. 2 Low Limit
194	Meas. 2 High Limit
195	Meas. 3 Quality Bad
196	Meas. 3 Low Limit
197	Meas. 3 High Limit
198	Classified Status 2
199	Status Flags for Measurements 4-7.
200	Reserved for Future Use
201	Meas. 4 Quality Bad
202	Meas. 4 Low Limit
203	Meas. 4 High Limit
204	Meas. 5 Quality Bad
205	Meas. 5 Low Limit
206	Meas. 5 High Limit
207	Meas. 6 Quality Bad
208	Meas. 6 Low Limit
209	Meas. 6 High Limit
210	Meas. 7 Quality Bad
211	Meas. 7 Low Limit
212	Meas. 7 High Limit
213	Classified Status 3
214	Status Flags for Measurements 8-11.
215	Meas. 8 Quality Bad
216	Meas. 8 Low Limit
217	Meas. 8 High Limit
218	Meas. 9 Quality Bad
219	Meas. 9 Low Limit
220	Meas. 9 High Limit
221	Meas. 10 Quality Bad
222	Meas. 10 Low Limit
223	Meas. 10 High Limit
224	Meas. 11 Quality Bad
225	Meas. 11 Low Limit
226	Meas. 11 High Limit
227	Classified Status 4
228	Status Flags for Measurements 12-15.
229	Meas. 12 Quality Bad
230	Meas. 12 Low Limit
231	Meas. 12 high Limit
232	Meas. 13 Quality Bad
233	Meas. 13 Low Limit
234	Meas. 13 High Limit
235	Meas. 14 Quality Bad
236	Meas. 14 Low Limit
237	Meas. 14 High Limit
238	Meas. 15 Quality Bad
239	Meas. 15 Low Limit
240	Meas. 15 High Limit
241	HACH Logo
242	Sensor Image
243	Sodium Concentration
244	Sensor Bar Graph
245	PV
246	Device Variables
247	Identification
248	Primary Variable
249	Measured Values
250	Sensor Description
251	HART Tags
252	Device Info.
253	Revisions
254	Sensor Information
255	Status
256	Diagnostics
257	Prognosys
258	Device Errors
259	Device Warnings
260	Classified Error
261	Analyzer Diagnostics
262	Analyzer Diagnosys
263	Maintenance
264	Sensor Maintenance
265	Sodium Concentration Setup
266	HART Setup
267	Sensor Identification
268	Loop Current A
269	Alarm Type Loop A
270	Channel A Flags
271	Loop Current B
272	Alarm Type Loop B
273	Channel B Flags
274	Loop Current C
275	Loop A Current
276	mA
277	.2f
278	Alarm A Select
279	Loop A Flags
280	Loop B Current
281	Alarm B Select
282	Loop B Flags
283	Loop C Current
284	Alarm C Select
285	Loop C Flags
286	LRV Loop A
287	Lower Range Value Loop A.
288	14.4f
289	LRV Loop B
290	Lower Range Value Loop B.
291	LRV Loop C
292	Lower Range Value Loop C.
293	URV Loop A
294	Upper Range Value Loop A.
295	URV Loop B
296	Upper Range Value Loop B.
297	URV Loop C
298	Upper Range Value Loop C.
299	Transfer Val Loop A
300	Sets the transfer value. Range 3.0 to 23.0 mA (default 4.000).
301	Transfer Val Loop B
302	Transfer Val Loop C
303	Test Value Loop A.
304	Test Value Loop B.
305	Test Value Loop C.
306	LSL Loop A
307	Lower Sensor Limit Loop A.
308	LSL Loop B
309	Lower Sensor Limit Loop B.
310	LSL Loop C
311	Lower Sensor Limit Loop C.
312	USL Loop A
313	Upper Sensor Limit Loop A.
314	USL Loop B
315	Upper Sensor Limit Loop B.
316	USL Loop C
317	Upper Sensor Limit Loop C.
318	Error Hold Mode
319	Holds Outputs at last known value or switches to Transfer mode when sensor loses communication with controller.
320	Hold Outputs
321	Transfer to defined Value
322	Meas. Select Loop A
323	Selection list of sensor measurements.
324	Meas. Select Loop B
325	Meas. Select Loop C
326	Filter Loop A
327	Loop Filter Time Constant.
328	5d
329	Filter Loop B
330	Filter Loop C
331	4mA Cal Count A
332	Output Loop 4mA calibration value in D/A counts.
333	Counts
334	4mA Cal Count B
335	4mA Cal Count C
336	20mA Cal Count A
337	Output Loop 20mA calibration value in D/A counts.
338	20mA Cal Count B
339	20mA Cal Count C
340	Test Enable Loop A
341	Disabled
342	Enabled
343	Test Enable Loop B
344	Test Enable Loop C
345	User Hold Loop A
346	Selection List of user Hold Modes.
347	User Hold Loop B
348	User Hold Loop C
349	Units Loop A
350	Engineering Units Loop A.
351	Units Loop B
352	Engineering Units Loop B.
353	Units Loop C
354	Engineering Units Loop C.
355	HART Loop A Mode
356	HART Loop Modes. Fixed Current = 4 mA. Active Current = 4-20 mA.
357	Fixed Current
358	Active Current
359	HART Loop B Mode
360	HART Loop A Address
361	HART Loop Address (0-63) 0->Single Loop.
362	HART Loop B Address
363	Mapping Output A
364	Status of HART Output A mapping to HART sensor.
365	Inactive
366	Active
367	Mapping Output B
368	Status of HART Output B mapping to HART sensor.
369	Mapping Output C
370	Status of HART Output C mapping to HART sensor.
371	HART Channel A
372	Status of HART Channel A mapping to HART sensor.
373	HART Channel B
374	Status of HART Channel B mapping to HART sensor.
375	Location or Name of HART Module.
376	Application Code Version.
377	Boot Code Version.
378	Serial Number
379	HART Module serial number.
380	Date
381	Sets the controller date.
382	Time
383	Sets the controller time.
384	Fix analog output A
385	Fix analog output B
386	Fix analog output C
387	Trim analog output A
388	Trim analog output B
389	Trim analog output C
390	Loop A Gauge
391	Loop B Gauge
392	Loop C Gauge
393	Online
394	Offline
395	HART Network Module
396	Loop Currents
397	HART Module Identification
398	Loop A
399	Loop B
400	Loop C
401	Loop Maintenance
402	Device Mapping
403	Status of Relays and Outputs Mapped to the HART sensor.
404	Loop A Maintenance
405	Loop B Maintenance
406	Loop C Maintenance
407	HART Network Module Settings
408	Date and Time Settings
409	Output A Setup
410	Output B Setup
411	Output C Setup
412	Hold Modes
413	Common Tables
414	Interoperable *
415	Universal
416	Common Practice
417	Pressure Universal
418	Pressure Common
419	Menu
420	Rosemount Magflow
421	Rosemount Pressure
422	Moore Products
423	Siemens Pressure
424	P2 Common
425	Wireless
426	Munge
427	Analytical Oxygen/Combustion/Methane/CO
428	Flow Totalizer - Rate Indicator
429	Flow Variable Area
430	Flow Coriolis Mass
431	Flow Ultrasonic - Gas
432	Flow Ultrasonic - Liquid
433	Level Ultrasonic
434	Level Radar - Microwave
435	Pressure Absolute
436	Level Capacitance
437	Pressure Differential
438	Level Hydrostatic
439	Level
440	Pressure Absolute/Relative
441	Level Microwave
442	Level Radar
443	Level Density - Nuclear
444	Flow Electromagnetic
445	Flow Vortex
446	Flow Magmeter - Rack Version
447	Flow High Performance Magmeter
448	Flow Mass
449	Flow Ultrasonic
450	Flow Magnetic
451	Flow Magnetic - Custody Transfer
452	Flow 2-wire Magnetic
453	Flow Coriolis Mass - Custody Transfer
454	Flow 2-wire Vortex
455	Flow Thermal
456	Temperature Head Mounted
457	Temperature Compact
458	Temperature DIN Rail Mounted
459	Analytical pH
460	Analytical Conductivity - Conductive
461	Analytical Conductivity - Inductive
462	Temperature Sensor
463	Level Servo
464	Temperature DIN Rail
465	Temperature
466	Analytical ORP
467	Analytical pION
468	Analytical IConc
469	Analytical Electrode Conductivity
470	Analytical Toroidal Conductivity
471	Valve Positioner
472	Valve Controller
473	Pressure
474	Pressure Multivariable
475	Analytical pH/ORP
476	Flow Coriolis
477	Analytical Conductivity
478	Valve Positioner/Pneumatic
479	Valve Actuator - Electrical
480	Temperature Dual Input
481	Valve Actuator
482	Analytical Corrosion
483	Analytical Density - Nuclear
484	Level Continuous Gamma
485	Level Laser Ranging
486	Pressure Safety
487	Flow Vortex/Swirl
488	Flow
489	Analytical 4 Electrode Conductivity
490	Analytical 2 Electrode Conductivity
491	Analytical Troidal Conductivity
492	Analytical pH/ORP/pIon/Ion Conc
493	Analytical Oxygen
494	Pressure P, dP + Multivariable
495	Temperature 2-wire
496	Pressure w/ PID
497	Pressure Saturated Steam
498	Analytical Density - Gamma Ray
499	Level Gamma Ray
500	Analytical Weight - Gamma Ray
501	Level w/ Density - Gamma Ray
502	Analytical Motorized Density
503	Flow Multivariable Mass
504	Temperature Multivariable
505	Specialty HART-to-Analog Signal Conv
506	Flow dP
507	Pressure Low Power
508	Pressure Certified SIL2
509	Interoperable
510	Analytical Density
511	Valve Positioner/Electropneumatic
512	Flow Magnetic Inductive
513	Analytical
514	Analytical Opacity Monitor
515	Analytical Oxygen/Combustion
516	Analytical 2-wire Conductivity
517	Analytical 2-wire Conductivity w/ pure H20
518	Analytical 2-wire Conductivity w/ % conc
519	Analytical 2-wire Oxygen/Chlorine/Ozone
520	Analytical 2-wire pH/ORP
521	Analytical 2-wire Contacting/Toroidal
522	Analytical Oxygen - High Temperature
523	Analytical Conductivity w/ % conc
524	Analytical pH/ORP/ISE
525	Analytical Amperometric Analyzer
526	Analytical Dual Input Analyzer
527	Pressure Pressure/Level
528	Analytical Consistency
529	Analytical Microwave-Pulp Consistency
530	Analytical Microwave Consistency
531	Valve Digital Positioner
532	Valve Smart Valve Positioner
533	Temperature Differential
534	Analytical Dissolved Oxygen
535	Analytical pH Controller
536	Analytical Conductivity/Resistivity Controller
537	Analytical Conductivity/Resistivity
538	Level Displacement
539	Temperature w/ PID
540	Valve Universal Positioner
541	Level Radar - Reflex
542	Pressure Gauge
543	Pressure Sealed Gauge
544	Valve Digital Positioner w/ PID
545	Valve Intelligent Positioner
546	Analytical Gas Detector
547	Analytical Infrared Gas Detector
548	Analytical Electrochemical Gas Detector
549	Analytical Measuring Instruments
550	Level Magnostrictive
551	Valve On/Off Valve Controller
552	Level Radar - Pulse
553	Level Continuous Capactive
554	Valve Damper Actuator
555	Valve Electric Damper Actuator
556	Flow Electronic
557	Flow Vortex - Multiparameter Mass
558	Analytical UV Flame Detector
559	Analytical UVIR Flame Detector
560	Analytical IR Flame Detector
561	Analytical Fire Detector
562	Analytical Gas Detector Display Interface
563	Analytical Toxic Gas Detector
564	Analytical Flame Detector
565	Level Nuclear
566	Analytical Microwave
567	Analytical Density - Radiometric
568	Level Radiometric
569	Analytical Gas/Steam
570	Level Nucleonic
571	Analytical Blade Consistency
572	Analytical Rotary Consistency
573	Pressure Absolute/Differential
574	Positioner
575	Analytical Combustible Gas Detector
576	Analytical Point Infrared Gas Detector
577	Analytical Multi-Detector Monitor System
578	Valve Positioner/Electro-hydraulic
579	Valve Monitor
580	Enable on token-passing data link layer only
581	Enable on TDMA data link layer only
582	Enable on both TDMA and token-passing data link layer
583	WirelessHART Device
584	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
585	Primary
586	Primary Analog Channel
587	Secondary
588	Secondary Analog Channel
589	Tertiary
590	Tertiary Analog Channel
591	Quaternary
592	Quaternary Analog Channel
593	Quinary
594	Quinary Analog Channel
595	Critical Power Failure
596	Lock all
597	Trim not supported
598	Configuration cannot be changed
599	Locked by gateway
600	Analog Input Channel
601	Analog Output Channel
602	Secondary Analog Channel Saturated
603	Tertiary Analog Channel Saturated
604	Quaternary Analog Channel Saturated
605	Quinary Analog Channel Saturated
606	Secondary Analog Channel Fixed
607	Tertiary Analog Channel Fixed
608	Quaternary Analog Channel Fixed
609	Quinary Analog Channel Fixed
610	Simulation active
611	The device is in simulation mode and the level output is not representative of the process.
612	Non-Volatile memory failure
613	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
614	Volatile memory error
615	The RAM memory check is invalid or maybe corrupt
616	Watchdog reset executed
617	A watchdog reset has been performed
618	Voltage conditions out of range
619	A voltage condition is outside its allowable range
620	Environmental conditions out of range
621	An internal or environmental condition is beyond acceptable limits.
622	Electronic failure
623	A hardware problem not related to the sensor has been detected.
624	Subdevice list changed
625	Duplicate master detected
626	Capacity Denied
627	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
628	Bandwidth allocation pending
629	Block transfer pending
630	Continuous
631	The Burst Message is published continuously at (worst case) the Minimum Update Period.
632	Window
633	The Burst Message is triggered when the source value deviates more than the specified trigger value
634	Rising
635	The Burst Message is triggered when source value Rises Above the specified trigger value.
636	Falling
637	The Burst Message is triggered when the source value Falls Below the specified trigger value.
638	On-change
639	The Burst Message is triggered when any value in the message changes.
640	Battery life
641	Percent range
642	Loop current
643	Primary variable
644	Secondary variable
645	Tertiary variable
646	Quaternary variable
647	Off
648	Enable event notification on token-passing data link layer
649	Enable event notification on TDMA data link layer
650	Enable event notification on TDMA and token-passing data link layer
651	Configuration changed event pending
652	Device status event pending
653	More status available event pending
654	Disable
655	Enable single data point trending
656	Enable filtered trending
657	The sample is filtered using a time constant equal to one-third the trend sample period
658	Enable average trending
659	The value obtained by dividing the sum of all samples in the period by the total number of samples
660	Read receive time
661	Write date and time
662	Non-Volatile Clock
663	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
664	Clock Uninitialized
665	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
666	Line Power
667	Device is powered via a hardwired connection to a plant power source.
668	Battery Power
669	Device operates solely of its (internal) battery.
670	Recharg.B./Power Sc.
671	Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat).
672	Idle
673	Active search
674	Looking for neighbors.
675	Negotiating
676	Quarantined
677	Operational
678	Suspended
679	Deep sleep
680	Ultra-low power
681	Wireless Signal Found
682	Network packets have been recognized
683	Wireless Signal Identified
684	Wireless Time Synchronized
685	WirelessHart Signal Identified
686	Network Admission Requested
687	Set on transmission of first join request
688	Join Retrying
689	Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started.
690	Join Failed
691	Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search.
692	Network Security Clearance Granted
693	Network Manager Session Established
694	Network Joined
695	Network Joined. Normal superframe and links obtained.
696	Network Bandwidth Requested
697	Negotiating Network Properties. Gateway session obtained.
698	Join Complete
699	Normal operating mode.
700	None
701	No restrictions
702	SI Only
703	Restricted to SI Unit codes only
704	Open - accept all devices
705	Use Whitelist for access
706	Use Blacklist
707	Use Whitelist and Blacklist
708	Lockdown - disable join links
709	Process automation device
710	Discrete device
711	Hybrid:Process automation+discrete
712	I/O System
713	WirelessHART Process automation device
714	WirelessHART Discrete device
715	WirelessHART Process automation+discrete
716	WirelessHART Gateway
717	WirelessHART Access point
718	WirelessHART Process adapter
719	WirelessHART Discrete adapter
720	WirelessHART enabled handheld/portable maintenance tool
721	Don't attempt to join
722	Join now
723	Attempt to join immediately on powerup or reset
724	US
725	United States of America
726	JP
727	Japan
728	DE
729	Germany
730	FR
731	France
732	ES
733	Spain
734	RU
735	Russian Federation
736	CN
737	People's Republic of China
738	Nominal
739	Device Power Status is nominal
740	Low
741	Device Power Status is low
742	Critically Low
743	Device Power Status is critically low
744	Recharging - Low
745	Recharging - High
746	Secondary Master
747	Primary Master
748	PV Analog Channel Saturated
749	PV Analog Channel Fixed
750	Device Profile
751
752	Device Diagnostic Status 0
753	Device Diagnostic Status 1
754	I/O and Subdevice Status
755	WirelessHART Status
756	Time Set Option
757	Real Time Clock Flags
758	Country
759	Country of intended device installation
760	SI Unit Control
761	Indicates if device should only display SI unit codes
762	Burst Trigger Units
763	Burst Trigger Class
764	Wired HART Enabled
765	Enabled on Wired HART device connection only
766	Wireless HART Enabled
767	Enabled on WirelessHART device connection only
768	Both Wired and WirelessHart Enabled
769	Enabled on both Wired and WirelessHART connections
770	Burst Msg Trigger Mode
771	Event Status
772	Event Notification Control
773	Operate mode Mask
774	Not Defined
775	Power Source
776	Power source of the device
777	Wireless Mode
778	Join Status
779	The current location in the joining sequence of operations.
780	Network Access Mode
781	Join Mode
782	Power Status
783	Power status of the device
784	Master Mode
785	This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode.
786	Trend Units
787	Trend Device Variable Unit Code
788	Trend Classification
789	Trend Device Variable Classification
790	Trend Control
791	Device Status Mask
792	Ext dev status Mask
793	Device Diagnostic Status 0 Mask
794	Device Diagnostic Status 1 Mask
795	Device Diagnostic Status 2 Mask
796	Device Diagnostic Status 3 Mask
797	AO saturated Mask
798	AO fixed Mask
799	Latched Device Status
800	Latched Ext dev status
801	Latched Operate Mode
802	Latched Device Diagnostic Status 0
803	Latched Device Diagnostic Status 1
804	Latched Device Diagnostic Status 2
805	Latched Device Diagnostic Status 3
806	Latched AO saturated
807	Latched AO fixed
808	Wireless Module Device Type
809	Device type of the Wireless Radio
810	Wireless Module Manufacturer ID
811	Manufacturer of the Wireless Radio contained in this device
812	Subdevice Device Type
813	Device type of the subdevice attached to this system.
814	Subdevice Manufacturer Id
815	Manufacturer of the subdevice attached to this system.
816	Time Stamp
817	Relative time value on network
818	8u
819	Dynamic Variables Returned for Device Variables
820	Command Response Truncated
821	Configuration Change Counter Mismatch
822	Status bytes mismatch
823	8.3f
824	.3f
825	Output A is fixed at %{0}.
826	Output B is fixed at %{0}.
827	Output C is fixed at %{0}.
828	Output A output equal to reference meter?
829	Output B output equal to reference meter?
830	Output C output equal to reference meter?
Reference ID	String