HART设备字典

Loading…

引用ID	字符串
0	MYPRO PH
1	Set tag number
2	Error No. 1 Internal fault
3	Error No. 2 Error: EEPROM System data
4	Error No. 7 ASIC error
5	Error No. 8 SCS alarm glass electrode
6	Error No. 10 Alarm : Temperature sensor
7	Error No. 30 SCS alarm Reference electrode
8	Error No. 32 Slope calibration beyond electrode slope
9	Error No. 33 Zero calibration zero point perform. too large
10	Error No. 34 Zero calibration mV range overstepped
11	Error No. 41 Calibr.parameters not usable
12	Error No. 42 Buffer difference to isotherm. point too small
13	Error No. 43 Buffer difference too small
14	Error No. 44 Measured value by calibration unstable
15	Error No. 45 Calibration aborted
16	Error No. 46 Current output range limits exchanged
17	Error No. 55 Main parameter below limit of measuring range
18	Error No. 57 Main parameter exceeded measuring range
19	Error No. 59 Temperature below limit of measuring range
20	Error No. 61 Temperature exceeded measuring range
21	Error No. 63 Current output below limit of measuring range
22	Error No. 64 Current output exceeded measuring range
23	Warning No. 80 Current output span too small
24	Warning No.100 Simulation current output active
25	Warning No.101 Service additional function active
26	Warning No.106 Download active
27	Error No.116 Download error
28	AO
29	5.2f
30	6.1f
31	Measured value
32	6.0f
33	4.2f
34	Temperature
35	5.1f
36	Operating status
37	3u
38	Signal damping
39	Value for 4 mA
40	5.f
41	Value for 20 mA
42	Typ of measurem.
43	symmetrical
44	asymmetrical
45	Operating mode
46	pH
47	ORP
48	Offset
49	Zero point
50	Slope
51	mV/pH
52	Isotherm. point
53	Type of compens.
54	Standard
55	Isotherm
56	Type of buffer
57	Endress+Hauser
58	Ingold
59	Merck/Riedel
60	DIN
61	Japan
62	Type of sensor
63	Glass 7.0
64	Glass 4.6
65	Antimony
66	Temp. measurem.
67	Temp. compensation
68	MTC+temp. off
69	MTC+temp. on
70	ATC+temp. on
71	MTC temp. entry
72	Temp. correction
73	Calibr. buffer
74	Buffer value 1
75	Buffer value 2
76	Auto HOLD at cal
77	SCS pH electrode
78	SCS ref electrode
79	Ref. alarm tresh.
80	6.f
81	Failure
82	Error No. 1
83	Error No. 2
84	Error No. 7
85	Error No. 8
86	Error No. 10
87	Maintenance
88	Error No. 30
89	Error No. 32
90	Error No. 33
91	Error No. 34
92	Error No. 41
93	Error No. 42
94	Error No. 43
95	Error No. 44
96	Error No. 45
97	Error No. 46
98	Fault
99	Error No. 55
100	Error No. 57
101	Error No. 59
102	Error No. 61
103	Error No. 63
104	Error No. 64
105	Warning
106	Warning No. 80
107	Warning No.101
108	Warning No.106
109	Warning No.116
110	Alarm delay
111	3u
112	Security locking
113	4u
114	Default values
115	Sim. current out.
116	Set sim. current
117	Device data
118	HART output
119	Offline
120	Matrix group sel.
121	Main parameter
122	calibration
123	Main functions
124	Calibr.parameters
125	SCS alarm
126	Status: Normal
127	Status: Error
128	Alarm assignment
129	Diagnosis
130	Service/simulation
131	User information
132	Hot key
133	Autom. buffering
134	Man. 2-Point-Cal.
135	Man. zero cal.
136	Man. slope cal.
137	Start remote cal.
138	Disturbance
139	Diagnostic code
140	Software version
141	Hardware version
142	FMU860
143	DT
144	DVC
145	FCX
146	AS800
147	340T
148	340C
149	344
150	Siemens Micro K
151	SITRANS L
152	SIPAN PH
153	SITRANS P
154	75SMT
155	UNIDELTA
156	8320
157	SX5100
158	TSV175
159	DMU
160	3780
161	BM70
162	8u
163	Device is in reset mode please wait...
164	%[L]{0}
165	Caution! Values are reseted
166	Calibration stopped Immerse electrode in process
167	Calibration completed successfully
168	Calibration completed with status messages Indicate?
169	Yes;No
170	Immerse electrode in process
171	Indicate calib. parameter?
172	Calibr. parameters
173	End;Sensor zero;Sensor slope;Calib. buffer 1;Calib. buffer 2
174	%[L]{0} %{0} %{1}
175	End;Sensor zero;Sensor slope
176	Indicate calibr. parameters?
177	Write protected Calibration not possible
178	Calibration not possible
179	%[L]{0} %{0} Immerse electrode in buffer 1
180	Calibration running please wait... MV %[5.2f]{0} %{1}
181	%[L]{0} %{0} Immerse electrode in buffer 2
182	Please wait...
183	Immerse electrode in buffer 1
184	Calibration running MV %{0} %{1}
185	Read value;Accept value
186	Immerse electrode in buffer 2
187	Immerse electrode in buffer
188	Device is hardware-write-protected
189	No errors detected
190	%[L]{0} %[5.2f]{soft_ver_anzeige}
191	%[L]{0} %[2u]{hardware_ver_part1}.0%[1u]{hardware_ver_part2}
192	%[L]{0} %[2u]{hardware_ver_part1}.%[2u]{hardware_ver_part2}
193	Device reset;Sensor reset;General reset
194	Caution! values are reseted
引用ID	字符串