Device dictionary

Loading…

Reference ID	String
0	Set failed
1	Invalid float
2	Command Response Truncated
3	Program pause
4	Resume program
5	Program stop
6	Start program
7	Analog fieldbus device variable
8	The sources of data on offer depend on your device version. All the sensors and controllers connected to inputs are available for selection.
9	Source
10	Current output source
11	Analyzer_Phosphate_yellow
12	Status signal
13	Hold behavior
14	Freeze last value: The device holds the last value before the Hold and sets the status of device variable to "stable". Status only: A Hold does not affect the value of the device variable, changes of measured value continue to be displayed. The status of the device variable is set to "stable".
15	Termination
16	ResultType
17	Unit
18	Device hold
19	Mode
20	SensorType_Sensor_CH1
21	SensorType_Sensor_CH2
22	SensorType_Sensor_CH3
23	SensorType_Sensor_CH4
24	SensorType_Sensor_CH5
25	SensorType_Sensor_CH6
26	SensorType_Sensor_CH7
27	Input variable
28	Mode
29	AppliedSensorHWID
30	Sensor type
31	Port activation state
32	Use this function to activate to deactivate a variable being output at the current output
33	DeviceConnectionState
34	Availability
35	Electrode slot 1
36	Operating mode
37	Photometer type
38	Channel
39	Memosens control mode
40	SP type
41	Instance
42	TurbiditySensorType
43	None
44	SP1 Main value
45	SP2 Main value
46	SP3 Main value
47	SP4 Main value
48	SP5 Main value
49	SP6 Main value
50	CH1 Measurement value
51	CH1 Interface
52	CH1 Heartbeat Sensor status
53	CH1 Temperature
54	CH1 Reference value
55	CH1 Turbidity
56	CH1 Heartbeat Sensor health
57	CH1 Raw value (1)
58	CH1 2nd meas. value
59	CH1 Heartbeat Maintenance timer
60	CH1 NO3
61	CH1 Turbidity Formazine
62	CH1 Raw value (2)
63	CH1 Raw meas. current
64	CH1 SAC
65	CH1 Concentration
66	CH1 Raw value (3)
67	CH1 Raw ref. current
68	CH1 Conductivity
69	CH1 Raw value nA
70	CH1 NO3-N
71	CH1 rH
72	CH1 Turbidity solid
73	CH1 Raw value (4)
74	CH1 Lamp current
75	CH1 Transm.
76	CH1 Sensor current
77	CH1 SpectroCAS Parameter 1
78	CH1 Resistance
79	CH1 Partial pressure
80	CH1 ORP mV
81	CH1 Lamp voltage
82	CH1 ORP %
83	CH1 Raw meas. value
84	CH1 Absorption
85	CH1 SpectroCAS Parameter 2
86	CH1 TDS
87	CH1 Concentration liquid
88	CH1 Raw value mV
89	CH1 Raw ref. value
90	CH1 Concentration gaseous
91	CH1 Raw 2nd meas. value
92	CH1 COD
93	CH1 SpectroCAS Parameter 3
94	CH1 Saturation
95	CH1 Concentration (1)
96	CH1 Raw value μs
97	CH1 pH
98	CH1 Turbidity AU
99	CH1 Concentration (2)
100	CH1 TOC
101	CH1 SpectroCAS Parameter 4
102	CH1 Glass Impedance
103	CH1 Concentration (3)
104	CH1 Leakage current
105	CH1 Concentration (4)
106	CH1 DOC
107	CH1 SpectroCAS Parameter 5
108	CH1 Reference Impedance
109	CH1 Turbidity %
110	CH1 BOD
111	CH1 pH (1)
112	CH1 Turbidity user unit
113	CH1 pH (2)
114	CH1 pH (3)
115	CH1 Tr. 10mm
116	CH1 Turbidity OD
117	CH1 pH (4)
118	CH1 Raw value 5mm
119	CH1 Raw value 10mm
120	CH1 ORP mV (1)
121	CH1 ORP mV (2)
122	CH1 ORP mV (3)
123	CH1 ORP mV (4)
124	CH2 Measurement value
125	CH2 Interface
126	CH2 Heartbeat Sensor status
127	CH2 Temperature
128	CH2 Reference value
129	CH2 Turbidity
130	CH2 Heartbeat Sensor health
131	CH2 Raw value (1)
132	CH2 2nd meas. value
133	CH2 Heartbeat Maintenance timer
134	CH2 NO3
135	CH2 Turbidity Formazine
136	CH2 Raw value (2)
137	CH2 Raw meas. current
138	CH2 SAC
139	CH2 Concentration
140	CH2 Raw value (3)
141	CH2 Raw ref. current
142	CH2 Conductivity
143	CH2 Raw value nA
144	CH2 NO3-N
145	CH2 rH
146	CH2 Turbidity solid
147	CH2 Raw value (4)
148	CH2 Lamp current
149	CH2 Transm.
150	CH2 Sensor current
151	CH2 SpectroCAS Parameter 1
152	CH2 Resistance
153	CH2 Partial pressure
154	CH2 ORP mV
155	CH2 Lamp voltage
156	CH2 ORP %
157	CH2 Raw meas. value
158	CH2 Absorption
159	CH2 SpectroCAS Parameter 2
160	CH2 TDS
161	CH2 Concentration liquid
162	CH2 Raw value mV
163	CH2 Raw ref. value
164	CH2 Concentration gaseous
165	CH2 Raw 2nd meas. value
166	CH2 COD
167	CH2 SpectroCAS Parameter 3
168	CH2 Saturation
169	CH2 Concentration (1)
170	CH2 Raw value μs
171	CH2 pH
172	CH2 Turbidity AU
173	CH2 Concentration (2)
174	CH2 TOC
175	CH2 SpectroCAS Parameter 4
176	CH2 Glass Impedance
177	CH2 Concentration (3)
178	CH2 Leakage current
179	CH2 Concentration (4)
180	CH2 DOC
181	CH2 SpectroCAS Parameter 5
182	CH2 Reference Impedance
183	CH2 Turbidity %
184	CH2 BOD
185	CH2 pH (1)
186	CH2 Turbidity user unit
187	CH2 pH (2)
188	CH2 pH (3)
189	CH2 Tr. 10mm
190	CH2 Turbidity OD
191	CH2 pH (4)
192	CH2 Raw value 5mm
193	CH2 Raw value 10mm
194	CH2 ORP mV (1)
195	CH2 ORP mV (2)
196	CH2 ORP mV (3)
197	CH2 ORP mV (4)
198	CH3 Measurement value
199	CH3 Interface
200	CH3 Heartbeat Sensor status
201	CH3 Temperature
202	CH3 Reference value
203	CH3 Turbidity
204	CH3 Heartbeat Sensor health
205	CH3 Raw value (1)
206	CH3 2nd meas. value
207	CH3 Heartbeat Maintenance timer
208	CH3 NO3
209	CH3 Turbidity Formazine
210	CH3 Raw value (2)
211	CH3 Raw meas. current
212	CH3 SAC
213	CH3 Concentration
214	CH3 Raw value (3)
215	CH3 Raw ref. current
216	CH3 Conductivity
217	CH3 Raw value nA
218	CH3 NO3-N
219	CH3 rH
220	CH3 Turbidity solid
221	CH3 Raw value (4)
222	CH3 Lamp current
223	CH3 Transm.
224	CH3 Sensor current
225	CH3 SpectroCAS Parameter 1
226	CH3 Resistance
227	CH3 Partial pressure
228	CH3 ORP mV
229	CH3 Lamp voltage
230	CH3 ORP %
231	CH3 Raw meas. value
232	CH3 Absorption
233	CH3 SpectroCAS Parameter 2
234	CH3 TDS
235	CH3 Concentration liquid
236	CH3 Raw value mV
237	CH3 Raw ref. value
238	CH3 Concentration gaseous
239	CH3 Raw 2nd meas. value
240	CH3 COD
241	CH3 SpectroCAS Parameter 3
242	CH3 Saturation
243	CH3 Concentration (1)
244	CH3 Raw value μs
245	CH3 pH
246	CH3 Turbidity AU
247	CH3 Concentration (2)
248	CH3 TOC
249	CH3 SpectroCAS Parameter 4
250	CH3 Glass Impedance
251	CH3 Concentration (3)
252	CH3 Leakage current
253	CH3 Concentration (4)
254	CH3 DOC
255	CH3 SpectroCAS Parameter 5
256	CH3 Reference Impedance
257	CH3 Turbidity %
258	CH3 BOD
259	CH3 pH (1)
260	CH3 Turbidity user unit
261	CH3 pH (2)
262	CH3 pH (3)
263	CH3 Tr. 10mm
264	CH3 Turbidity OD
265	CH3 pH (4)
266	CH3 Raw value 5mm
267	CH3 Raw value 10mm
268	CH3 ORP mV (1)
269	CH3 ORP mV (2)
270	CH3 ORP mV (3)
271	CH3 ORP mV (4)
272	CH4 Measurement value
273	CH4 Interface
274	CH4 Heartbeat Sensor status
275	CH4 Temperature
276	CH4 Reference value
277	CH4 Turbidity
278	CH4 Heartbeat Sensor health
279	CH4 Raw value (1)
280	CH4 2nd meas. value
281	CH4 Heartbeat Maintenance timer
282	CH4 NO3
283	CH4 Turbidity Formazine
284	CH4 Raw value (2)
285	CH4 Raw meas. current
286	CH4 SAC
287	CH4 Concentration
288	CH4 Raw value (3)
289	CH4 Raw ref. current
290	CH4 Conductivity
291	CH4 Raw value nA
292	CH4 NO3-N
293	CH4 rH
294	CH4 Turbidity solid
295	CH4 Raw value (4)
296	CH4 Lamp current
297	CH4 Transm.
298	CH4 Sensor current
299	CH4 SpectroCAS Parameter 1
300	CH4 Resistance
301	CH4 Partial pressure
302	CH4 ORP mV
303	CH4 Lamp voltage
304	CH4 ORP %
305	CH4 Raw meas. value
306	CH4 Absorption
307	CH4 SpectroCAS Parameter 2
308	CH4 TDS
309	CH4 Concentration liquid
310	CH4 Raw value mV
311	CH4 Raw ref. value
312	CH4 Concentration gaseous
313	CH4 Raw 2nd meas. value
314	CH4 COD
315	CH4 SpectroCAS Parameter 3
316	CH4 Saturation
317	CH4 Concentration (1)
318	CH4 Raw value μs
319	CH4 pH
320	CH4 Turbidity AU
321	CH4 Concentration (2)
322	CH4 TOC
323	CH4 SpectroCAS Parameter 4
324	CH4 Glass Impedance
325	CH4 Concentration (3)
326	CH4 Leakage current
327	CH4 Concentration (4)
328	CH4 DOC
329	CH4 SpectroCAS Parameter 5
330	CH4 Reference Impedance
331	CH4 Turbidity %
332	CH4 BOD
333	CH4 pH (1)
334	CH4 Turbidity user unit
335	CH4 pH (2)
336	CH4 pH (3)
337	CH4 Tr. 10mm
338	CH4 Turbidity OD
339	CH4 pH (4)
340	CH4 Raw value 5mm
341	CH4 Raw value 10mm
342	CH4 ORP mV (1)
343	CH4 ORP mV (2)
344	CH4 ORP mV (3)
345	CH4 ORP mV (4)
346	CH5 Measurement value
347	CH5 Interface
348	CH5 Heartbeat Sensor status
349	CH5 Temperature
350	CH5 Reference value
351	CH5 Turbidity
352	CH5 Heartbeat Sensor health
353	CH5 Raw value (1)
354	CH5 2nd meas. value
355	CH5 Heartbeat Maintenance timer
356	CH5 NO3
357	CH5 Turbidity Formazine
358	CH5 Raw value (2)
359	CH5 Raw meas. current
360	CH5 SAC
361	CH5 Concentration
362	CH5 Raw value (3)
363	CH5 Raw ref. current
364	CH5 Conductivity
365	CH5 Raw value nA
366	CH5 NO3-N
367	CH5 rH
368	CH5 Turbidity solid
369	CH5 Raw value (4)
370	CH5 Lamp current
371	CH5 Transm.
372	CH5 Sensor current
373	CH5 SpectroCAS Parameter 1
374	CH5 Resistance
375	CH5 Partial pressure
376	CH5 ORP mV
377	CH5 Lamp voltage
378	CH5 ORP %
379	CH5 Raw meas. value
380	CH5 Absorption
381	CH5 SpectroCAS Parameter 2
382	CH5 TDS
383	CH5 Concentration liquid
384	CH5 Raw value mV
385	CH5 Raw ref. value
386	CH5 Concentration gaseous
387	CH5 Raw 2nd meas. value
388	CH5 COD
389	CH5 SpectroCAS Parameter 3
390	CH5 Saturation
391	CH5 Concentration (1)
392	CH5 Raw value μs
393	CH5 pH
394	CH5 Turbidity AU
395	CH5 Concentration (2)
396	CH5 TOC
397	CH5 SpectroCAS Parameter 4
398	CH5 Glass Impedance
399	CH5 Concentration (3)
400	CH5 Leakage current
401	CH5 Concentration (4)
402	CH5 DOC
403	CH5 SpectroCAS Parameter 5
404	CH5 Reference Impedance
405	CH5 Turbidity %
406	CH5 BOD
407	CH5 pH (1)
408	CH5 Turbidity user unit
409	CH5 pH (2)
410	CH5 pH (3)
411	CH5 Tr. 10mm
412	CH5 Turbidity OD
413	CH5 pH (4)
414	CH5 Raw value 5mm
415	CH5 Raw value 10mm
416	CH5 ORP mV (1)
417	CH5 ORP mV (2)
418	CH5 ORP mV (3)
419	CH5 ORP mV (4)
420	CH6 Measurement value
421	CH6 Interface
422	CH6 Heartbeat Sensor status
423	CH6 Temperature
424	CH6 Reference value
425	CH6 Turbidity
426	CH6 Heartbeat Sensor health
427	CH6 Raw value (1)
428	CH6 2nd meas. value
429	CH6 Heartbeat Maintenance timer
430	CH6 NO3
431	CH6 Turbidity Formazine
432	CH6 Raw value (2)
433	CH6 Raw meas. current
434	CH6 SAC
435	CH6 Concentration
436	CH6 Raw value (3)
437	CH6 Raw ref. current
438	CH6 Conductivity
439	CH6 Raw value nA
440	CH6 NO3-N
441	CH6 rH
442	CH6 Turbidity solid
443	CH6 Raw value (4)
444	CH6 Lamp current
445	CH6 Transm.
446	CH6 Sensor current
447	CH6 SpectroCAS Parameter 1
448	CH6 Resistance
449	CH6 Partial pressure
450	CH6 ORP mV
451	CH6 Lamp voltage
452	CH6 ORP %
453	CH6 Raw meas. value
454	CH6 Absorption
455	CH6 SpectroCAS Parameter 2
456	CH6 TDS
457	CH6 Concentration liquid
458	CH6 Raw value mV
459	CH6 Raw ref. value
460	CH6 Concentration gaseous
461	CH6 Raw 2nd meas. value
462	CH6 COD
463	CH6 SpectroCAS Parameter 3
464	CH6 Saturation
465	CH6 Concentration (1)
466	CH6 Raw value μs
467	CH6 pH
468	CH6 Turbidity AU
469	CH6 Concentration (2)
470	CH6 TOC
471	CH6 SpectroCAS Parameter 4
472	CH6 Glass Impedance
473	CH6 Concentration (3)
474	CH6 Leakage current
475	CH6 Concentration (4)
476	CH6 DOC
477	CH6 SpectroCAS Parameter 5
478	CH6 Reference Impedance
479	CH6 Turbidity %
480	CH6 BOD
481	CH6 pH (1)
482	CH6 Turbidity user unit
483	CH6 pH (2)
484	CH6 pH (3)
485	CH6 Tr. 10mm
486	CH6 Turbidity OD
487	CH6 pH (4)
488	CH6 Raw value 5mm
489	CH6 Raw value 10mm
490	CH6 ORP mV (1)
491	CH6 ORP mV (2)
492	CH6 ORP mV (3)
493	CH6 ORP mV (4)
494	CH7 Measurement value
495	CH7 Interface
496	CH7 Heartbeat Sensor status
497	CH7 Temperature
498	CH7 Reference value
499	CH7 Turbidity
500	CH7 Heartbeat Sensor health
501	CH7 Raw value (1)
502	CH7 2nd meas. value
503	CH7 Heartbeat Maintenance timer
504	CH7 NO3
505	CH7 Turbidity Formazine
506	CH7 Raw value (2)
507	CH7 Raw meas. current
508	CH7 SAC
509	CH7 Concentration
510	CH7 Raw value (3)
511	CH7 Raw ref. current
512	CH7 Conductivity
513	CH7 Raw value nA
514	CH7 NO3-N
515	CH7 rH
516	CH7 Turbidity solid
517	CH7 Raw value (4)
518	CH7 Lamp current
519	CH7 Transm.
520	CH7 Sensor current
521	CH7 SpectroCAS Parameter 1
522	CH7 Resistance
523	CH7 Partial pressure
524	CH7 ORP mV
525	CH7 Lamp voltage
526	CH7 ORP %
527	CH7 Raw meas. value
528	CH7 Absorption
529	CH7 SpectroCAS Parameter 2
530	CH7 TDS
531	CH7 Concentration liquid
532	CH7 Raw value mV
533	CH7 Raw ref. value
534	CH7 Concentration gaseous
535	CH7 Raw 2nd meas. value
536	CH7 COD
537	CH7 SpectroCAS Parameter 3
538	CH7 Saturation
539	CH7 Concentration (1)
540	CH7 Raw value μs
541	CH7 pH
542	CH7 Turbidity AU
543	CH7 Concentration (2)
544	CH7 TOC
545	CH7 SpectroCAS Parameter 4
546	CH7 Glass Impedance
547	CH7 Concentration (3)
548	CH7 Leakage current
549	CH7 Concentration (4)
550	CH7 DOC
551	CH7 SpectroCAS Parameter 5
552	CH7 Reference Impedance
553	CH7 Turbidity %
554	CH7 BOD
555	CH7 pH (1)
556	CH7 Turbidity user unit
557	CH7 pH (2)
558	CH7 pH (3)
559	CH7 Tr. 10mm
560	CH7 Turbidity OD
561	CH7 pH (4)
562	CH7 Raw value 5mm
563	CH7 Raw value 10mm
564	CH7 ORP mV (1)
565	CH7 ORP mV (2)
566	CH7 ORP mV (3)
567	CH7 ORP mV (4)
568	CH8 Measurement value
569	CH8 Interface
570	CH8 Heartbeat Sensor status
571	CH8 Temperature
572	CH8 Reference value
573	CH8 Turbidity
574	CH8 Heartbeat Sensor health
575	CH8 Raw value (1)
576	CH8 2nd meas. value
577	CH8 Heartbeat Maintenance timer
578	CH8 NO3
579	CH8 Turbidity Formazine
580	CH8 Raw value (2)
581	CH8 Raw meas. current
582	CH8 SAC
583	CH8 Concentration
584	CH8 Raw value (3)
585	CH8 Raw ref. current
586	CH8 Conductivity
587	CH8 Raw value nA
588	CH8 NO3-N
589	CH8 rH
590	CH8 Turbidity solid
591	CH8 Raw value (4)
592	CH8 Lamp current
593	CH8 Transm.
594	CH8 Sensor current
595	CH8 SpectroCAS Parameter 1
596	CH8 Resistance
597	CH8 Partial pressure
598	CH8 ORP mV
599	CH8 Lamp voltage
600	CH8 ORP %
601	CH8 Raw meas. value
602	CH8 Absorption
603	CH8 SpectroCAS Parameter 2
604	CH8 TDS
605	CH8 Concentration liquid
606	CH8 Raw value mV
607	CH8 Raw ref. value
608	CH8 Concentration gaseous
609	CH8 Raw 2nd meas. value
610	CH8 COD
611	CH8 SpectroCAS Parameter 3
612	CH8 Saturation
613	CH8 Concentration (1)
614	CH8 Raw value μs
615	CH8 pH
616	CH8 Turbidity AU
617	CH8 Concentration (2)
618	CH8 TOC
619	CH8 SpectroCAS Parameter 4
620	CH8 Glass Impedance
621	CH8 Concentration (3)
622	CH8 Leakage current
623	CH8 Concentration (4)
624	CH8 DOC
625	CH8 SpectroCAS Parameter 5
626	CH8 Reference Impedance
627	CH8 Turbidity %
628	CH8 BOD
629	CH8 pH (1)
630	CH8 Turbidity user unit
631	CH8 pH (2)
632	CH8 pH (3)
633	CH8 Tr. 10mm
634	CH8 Turbidity OD
635	CH8 pH (4)
636	CH8 Raw value 5mm
637	CH8 Raw value 10mm
638	CH8 ORP mV (1)
639	CH8 ORP mV (2)
640	CH8 ORP mV (3)
641	CH8 ORP mV (4)
642	Controller 1 Bipolar
643	Controller 1 Unipolar+
644	Controller 1 Unipolar-
645	Controller 2 Bipolar
646	Controller 2 Unipolar+
647	Controller 2 Unipolar-
648	Controller 3 Bipolar
649	Controller 3 Unipolar+
650	Controller 3 Unipolar-
651	Controller 4 Bipolar
652	Controller 4 Unipolar+
653	Controller 4 Unipolar-
654	Binary input 1 PFM value
655	Binary input 1 Flow rate
656	Binary input 2 PFM value
657	Binary input 2 Flow rate
658	Binary input 3 PFM value
659	Binary input 3 Flow rate
660	Binary input 4 PFM value
661	Binary input 4 Flow rate
662	Binary input 1 Totalized flow
663	Binary input 1 Rainfall per time
664	Binary input 1 Totalized rainfall
665	Binary input 2 Totalized flow
666	Binary input 2 Rainfall per time
667	Binary input 2 Totalized rainfall
668	Binary input 3 Totalized flow
669	Binary input 3 Rainfall per time
670	Binary input 3 Totalized rainfall
671	Binary input 4 Totalized flow
672	Binary input 4 Rainfall per time
673	Binary input 4 Totalized rainfall
674	Binary input 5 Totalized flow
675	Binary input 5 Rainfall per time
676	Binary input 5 Totalized rainfall
677	Binary input 6 Totalized flow
678	Binary input 6 Rainfall per time
679	Binary input 6 Totalized rainfall
680	Current input 1 Current
681	Current input 1 Flow rate
682	Current input 1 Totalized flow
683	Current input 1 Parameter
684	Current input 2 Current
685	Current input 2 Flow rate
686	Current input 2 Totalized flow
687	Current input 2 Parameter
688	Current input 3 Current
689	Current input 3 Flow rate
690	Current input 3 Totalized flow
691	Current input 3 Parameter
692	Current input 4 Current
693	Current input 4 Flow rate
694	Current input 4 Totalized flow
695	Current input 4 Parameter
696	Current input 5 Current
697	Current input 5 Flow rate
698	Current input 5 Totalized flow
699	Current input 5 Parameter
700	Current input 6 Current
701	Current input 6 Flow rate
702	Current input 6 Totalized flow
703	Current input 6 Parameter
704	Temperature 1 Temperature
705	Temperature 2 Temperature
706	Temperature 3 Temperature
707	MF1 CO2 concentration
708	MF1 Difference value
709	MF1 Dual conductivity
710	MF1 Calculated pH
711	MF1 Redundant value
712	MF1 Calculated rH
713	MF1 Remaining op. time
714	MF1 Remaining capacity
715	MF1 Time until warn limit
716	MF1 Result numeric
717	MF2 CO2 concentration
718	MF2 Difference value
719	MF2 Dual conductivity
720	MF2 Calculated pH
721	MF2 Redundant value
722	MF2 Calculated rH
723	MF2 Remaining op. time
724	MF2 Remaining capacity
725	MF2 Time until warn limit
726	MF2 Result numeric
727	MF3 CO2 concentration
728	MF3 Difference value
729	MF3 Dual conductivity
730	MF3 Calculated pH
731	MF3 Redundant value
732	MF3 Calculated rH
733	MF3 Remaining op. time
734	MF3 Remaining capacity
735	MF3 Time until warn limit
736	MF3 Result numeric
737	MF4 CO2 concentration
738	MF4 Difference value
739	MF4 Dual conductivity
740	MF4 Calculated pH
741	MF4 Redundant value
742	MF4 Calculated rH
743	MF4 Remaining op. time
744	MF4 Remaining capacity
745	MF4 Time until warn limit
746	MF4 Result numeric
747	MF5 CO2 concentration
748	MF5 Difference value
749	MF5 Dual conductivity
750	MF5 Calculated pH
751	MF5 Redundant value
752	MF5 Calculated rH
753	MF5 Remaining op. time
754	MF5 Remaining capacity
755	MF5 Time until warn limit
756	MF5 Result numeric
757	MF6 CO2 concentration
758	MF6 Difference value
759	MF6 Dual conductivity
760	MF6 Calculated pH
761	MF6 Redundant value
762	MF6 Calculated rH
763	MF6 Remaining op. time
764	MF6 Remaining capacity
765	MF6 Time until warn limit
766	MF6 Result numeric
767	MF7 CO2 concentration
768	MF7 Difference value
769	MF7 Dual conductivity
770	MF7 Calculated pH
771	MF7 Redundant value
772	MF7 Calculated rH
773	MF7 Remaining op. time
774	MF7 Remaining capacity
775	MF7 Time until warn limit
776	MF7 Result numeric
777	MF8 CO2 concentration
778	MF8 Difference value
779	MF8 Dual conductivity
780	MF8 Calculated pH
781	MF8 Redundant value
782	MF8 Calculated rH
783	MF8 Remaining op. time
784	MF8 Remaining capacity
785	MF8 Time until warn limit
786	MF8 Result numeric
787	MRS set 1 Main value
788	MRS set 2 Main value
789	Heartbeat device Device status
790	Heartbeat device Device health
791	IsAutorangingUnit
792	HasSourceButNoValue
793	HasBinarySource
794	IsEmpty
795	HasMultipleValues
796	HasMultipleSourceValues
797	IsConnected
798	CationExchanger
799	Cond
800	DO
801	DegasedCond
802	DeviceGlobal
803	Difference
804	DifferenceCond
805	Disinfection
806	FieldbusInput
807	Formula
808	ISE
809	InputBinary
810	InputCurrent
811	InputTemperature
812	LimitSwitch
813	MeasuringRangeSwitch
814	MemosensCommon
815	Nitrate
816	OutputAlarmRelay
817	OutputBinary
818	OutputCurrent
819	OutputRelay
820	PA_FB_AnalogInput
821	PA_FB_DiscreteInput
822	PEM
823	PHCalculation
824	RHCalculation
825	Redundancy
826	Regulator
827	SAK
828	SamplePoint
829	SamplerInputBinary
830	SamplerOutputBinary
831	SpectroCAS
832	TimeSwitch
833	Turbidity
834	UIS
835	pH
836	Binary input 1 Edge counts
837	Binary input 1 Level
838	Binary input 2 Edge counts
839	Binary input 2 Level
840	Binary input 3 Edge counts
841	Binary input 3 Level
842	Binary input 4 Edge counts
843	Binary input 4 Level
844	Binary input 5 Edge counts
845	Binary input 5 Level
846	Binary input 6 Edge counts
847	Binary input 6 Level
848	MF1 Result binary
849	MF2 Result binary
850	MF3 Result binary
851	MF4 Result binary
852	MF5 Result binary
853	MF6 Result binary
854	MF7 Result binary
855	MF8 Result binary
856	Fieldbus AO 01
857	Fieldbus AO 02
858	Fieldbus AO 03
859	Fieldbus AO 04
860	#.#
861	Analyzer_Aluminium
862	Al
863	Analyzer_Ammonium
864	NH4-N
865	NH4
866	NH3
867	Analyzer_COD_cr
868	O2
869	Analyzer_COD_mn
870	Mn
871	Analyzer_Chromate
872	Cr(VI)
873	CrO4
874	Analyzer_Hardness
875	CaCO3
876	Ca
877	Analyzer_Iron
878	Fe
879	MPL version
880
881	Measuring parameter
882	MeasuringRangeSize
883	MeasuringRangeText_AMR_Range0
884	MeasuringRangeText_AMR_Range1
885	MeasuringRangeText_AMR_Range2
886	MeasuringRangeText_AMR_Range3
887	MeasuringRangeText_AMR_Range4
888	MeasuringRangeText_AMR_Range5
889	Measuring range
890	Manual
891	Automatic
892	Fieldbus
893	Analyzer_Nitrite
894	NO2-N
895	NO2
896	Analyzer_Phosphate_blue
897	PO4-P
898	PO4
899	P2O5
900	Hardware version
901	PhotometerInfo_LEDModule_IsAvailable
902	Serial number
903	Software version
904	Installation type
905	Others
906	Pressurized pipe sampling
907	Inlet pipe sampling
908	Analyzer_Silicate
909	SiO2
910	SiO2-Si
911	H2SiO3
912	Analyzer_Total_Nitrogen
913	TN
914	Analyzer_Total_Phosphate_Blue
915	P
916	WintertimeOperationActive
917	E_Off
918	E_On
919	ConfigDatabase_AvailablePIDController
920	E_AvailablePIDController_Standard
921	E_AvailablePIDController_Advanced
922	ConfigDatabase_CA80AnalyzerChannels
923	E_CA80AnalyzerChannels_1Channel
924	E_CA80AnalyzerChannels_1ChannelCascadedFluidic
925	E_CA80AnalyzerChannels_2Channel
926	E_CA80AnalyzerChannels_4Channel
927	E_CA80AnalyzerChannels_6Channel
928	ConfigDatabase_CA80Parameter
929	---
930	Ammonium
931	CODcr
932	O-phosphate
933	Iron
934	Nitrite
935	Chromate
936	Aluminum
937	Total phosphorus
938	Silica
939	Hardness
940	CODmn
941	Total nitrogen
942	ConfigDatabase_CA80Region
943	E_CA80Region_None
944	E_CA80Region_China
945	ConfigDatabase_CA80SampleDetectionSensor
946	None
947	Conductive
948	Capacitive
949	Flow rate
950	Device class
951	CM44x
952	CSF48
953	CA80
954	ConfigDatabase_Fieldbus
955	HART
956	PROFIBUS
957	Modbus
958	EtherNet/IP
959	PROFINET
960	ConfigDatabase_HeartbeatType
961	E_HeartbeatType_None
962	E_HeartbeatType_Monitoring
963	E_HeartbeatType_MonitoringAndVerification
964	ConfigDatabase_MathematicModulFormulaEnabled
965	ConfigDatabase_MeasuringRangeSwitchSet
966	ConfigDatabase_ProbenraumTemperierungDefault
967	E_Ohne_Probenraumtemperierung
968	E_Mit_Probenraumtemperierung
969	ConfigDatabase_ProduktFamilieDefault
970	Liquiline CM442
971	Liquiline CM448
972	Liquiport CSP44
973	Liquistation CSF48
974	Liquistation CSF22
975	Liquistation CSF33
976	Liquiline System CA80
977	Liquistation CSF34
978	Liquistation CSF39
979	Liquiline CM44P
980	Sampling device
981	Peristaltic
982	Vacuum
983	Inline
984	Addendum
985	Diag. code
986	002: Sensor unknown
987	004: Sensor defective
988	005: Sensor data invalid
989	010: Sensor scanning
990	012: Writing data failed
991	013: Sensor type wrong
992	018: Sensor not ready
993	022: Temperature sensor
994	061: Sensor electronic
995	062: Sensor connection
996	081: Initialization
997	100: Sensor communication
998	101: Sensor incompatible
999	102: Calibration timer
1000	103: Calibration timer
1001	104: Calibration validity
1002	105: Calibration validity
1003	106: Sensor TAG
1004	107: Calibration active
1005	108: SIP, CIP, autoclaving
1006	109: SIP, CIP, autoclav cap
1007	110: Init. channel
1008	111: Operating time cap
1009	114: Temp.offset high
1010	115: Temp. offset low
1011	116: Temp. slope high
1012	117: Temp. slope low
1013	118: Sensor glass break.
1014	119: Sensor check
1015	120: Sensor reference
1016	121: Sensor reference
1017	122: Sensor glass
1018	123: Sensor glass
1019	124: Sensor glass
1020	125: Sensor glass
1021	126: Sensor check
1022	127: Sensor check
1023	128: Sensor leakage
1024	129: Sensor leakage
1025	130: Sensor supply
1026	131: Sensor calibration
1027	132: Sensor calibration
1028	133: Sensor signal
1029	134: Sensor signal
1030	135: Sensor temp. low
1031	136: Sensor temp. high
1032	137: Sensor LED
1033	138: Sensor LED
1034	140: Sensor check
1035	141: Polarization
1036	142: Sensor signal
1037	143: Sensor check
1038	144: Conductivity range
1039	146: Sensor temperature
1040	147: Sensor check
1041	148: Sensor check
1042	149: Sensor LED
1043	150: Sensor check
1044	151: Sensor buildup
1045	152: Sensor data invalid
1046	153: Sensor defective
1047	154: Sensor data invalid
1048	155: Sensor defective
1049	156: Organic pollution
1050	157: Filter change
1051	158: Sensor check
1052	159: Sensor check
1053	160: Sensor data invalid
1054	161: Filter change
1055	162: Install.factor
1056	163: Install.factor
1057	164: Sensor data invalid
1058	168: Polarization
1059	169: Operating time
1060	170: Operating time
1061	171: Lamp change
1062	172: Echo lost
1063	173: Sludge level
1064	174: Turbid. failure
1065	175: Wiper failure
1066	176: Operating time
1067	177: Operating time
1068	178: Operating time
1069	179: Operating time
1070	180: Operating time
1071	181: Operating time
1072	182: Operating time
1073	183: Operating time
1074	184: Operating time
1075	185: Operating time
1076	186: Operating time
1077	187: Operating time
1078	188: Operating time
1079	189: Operating time
1080	190: Operating time
1081	191: Operating time
1082	192: Operating time
1083	193: Operating time
1084	194: Operating time
1085	195: Operating time
1086	196: Operating time
1087	197: Operating time
1088	198: Operating time
1089	199: Operating time
1090	202: Selftest active
1091	215: Simulation active
1092	216: Hold active
1093	241: Firmware failure
1094	242: Firmware incomp.
1095	243: Firmware failure
1096	261: Electronics module
1097	262: Module connection
1098	263: Incomp. detected
1099	284: Firmware update
1100	285: Update failure
1101	302: Battery low
1102	304: Module data
1103	305: Power consumption
1104	306: Software error
1105	310: Temperature sensor
1106	311: Temperature sensor
1107	312: Temperature sensor
1108	313: Safety sensor
1109	314: No sample flow
1110	315: Refrigeration
1111	316: Heating
1112	317: Liquidsensor
1113	318: Liquidsensor
1114	319: Safety sensor
1115	320: Safety sensor
1116	321: Liquid sensor
1117	322: Read sub-program
1118	323: Write sub-program
1119	324: Delete sub-program
1120	325: Read subprogram list
1121	326: Membrane pump
1122	327: Air-Manager
1123	328: Distribution arm
1124	329: Pump failure
1125	330: Membrane pump
1126	331: Peristaltic pump
1127	332: Peristaltic pump
1128	333: Pressure sensor
1129	334: Climate mod. defect.
1130	335: Fan defective
1131	337: Pump hose warning
1132	338: Pump hose alarm
1133	339: Liquidsensor warning
1134	340: Liquidsensor
1135	343: Power supply
1136	344: Program pause
1137	345: Time changeover
1138	346: Time changeover
1139	347: No sample confirm.
1140	348: Read program
1141	349: Write program
1142	350: UPS Battery
1143	351: Delete program
1144	352: Read Programlist
1145	353: Overfill check
1146	354: Bottle check
1147	355: Start time over
1148	356: Overfill check
1149	357: Sampling faulted
1150	358: Configuration
1151	359: Emptying error
1152	360: Reserved
1153	361: Reserved
1154	362: Reserved
1155	363: Reserved
1156	364: Reserved
1157	365: Reserved
1158	366: Reserved
1159	367: Reserved
1160	368: Reserved
1161	369: Reserved
1162	370: Internal voltage
1163	372: Reserved
1164	373: Electronictemp. high
1165	374: Sensor check
1166	375: No 4R module
1167	376: Reserved
1168	377: Reserved
1169	378: Reserved
1170	379: Reserved
1171	380: Reserved
1172	381: Reserved
1173	385: Reserved
1174	386: Reserved
1175	401: Factory reset
1176	403: Device verification active
1177	405: Service IP active
1178	408: Calibration aborted
1179	412: Writing backup
1180	413: Reading backup
1181	455: Mathemat. function
1182	460: Output below limit
1183	461: Output above limit
1184	500: Sensor calibration
1185	501: Sensor calibration
1186	502: No text catalog
1187	503: Language change
1188	505: Sensor calibration
1189	507: Sensor calibration
1190	509: Sensor calibration
1191	511: Sensor calibration
1192	513: Zero Warning
1193	515: Sensor calibration
1194	517: Sensor calibration
1195	518: Sensor calibration
1196	520: Sensor calibration
1197	522: Sensor calibration
1198	529: Diag. setup active
1199	530: Logbook at 80%
1200	531: Logbook full
1201	532: License error
1202	534: Electrolyte warning
1203	535: Sensor check
1204	536: SD card filled 80%
1205	537: SD card filled 100%
1206	538: SD card missing
1207	540: Parameter save fail
1208	541: Parameter load ok
1209	542: Parameter load fail
1210	543: Parameter load abort
1211	544: Parameter reset ok
1212	545: Parameter reset fail
1213	550: Process temperature
1214	551: Process temperature
1215	552: Conductivity low
1216	553: Conductivity high
1217	554: Concentration low
1218	555: Concentration high
1219	556: Temperature low
1220	557: Temperature high
1221	558: Conductivity low
1222	559: Conductivity high
1223	560: Conduc. compensation
1224	561: Conduc. compensation
1225	565: Reserved
1226	566: Package incompatible
1227	714: Reserved
1228	715: Reserved
1229	716: Reserved
1230	717: Reserved
1231	718: Reserved
1232	719: Reserved
1233	720: Membrane change
1234	724: Sensor reference
1235	725: Sensor reference
1236	726: Reserved
1237	727: Reserved
1238	728: Reserved
1239	729: Reserved
1240	730: Reserved
1241	731: Reserved
1242	732: Reserved
1243	733: Reserved
1244	734: Calibration quality
1245	740: Sensor defective
1246	770: Sensor deactivated
1247	771: Lamp change
1248	772: Lamp change
1249	773: Lamp change
1250	774: Lamp defective
1251	832: Temp. range exceeded
1252	841: Operating range
1253	842: Process value
1254	843: Process value
1255	844: Process value
1256	903: Minimum flow
1257	904: Process check alarm
1258	906: Cat.exchanger failure
1259	907: Cat.exchanger warning
1260	908: IEX capacity low
1261	909: IEX capacity exhausted
1262	910: Limit switch
1263	914: USP/ EP alarm
1264	915: USP / EP warning
1265	916: Reserved
1266	920: No sample
1267	921: Pump bracket open
1268	922: Armature cycle
1269	923: Armature cycle
1270	924: Inline armature
1271	925: Inline armature
1272	926: Inline armature
1273	927: Winter operation
1274	928: No sample
1275	929: Input signal
1276	930: Sample flow
1277	931: Reserved
1278	932: Reserved
1279	934: Process temp. high
1280	935: Process temp. low
1281	936: Reserved
1282	937: Controlled variable
1283	938: Controller setpoint
1284	939: Control. disturbance
1285	940: Reserved
1286	941: Reserved
1287	942: Process value
1288	943: Process value
1289	944: Sensor range
1290	945: pH value high
1291	946: pH value low
1292	951: Hold active CH1
1293	952: Hold active CH2
1294	953: Hold active CH3
1295	954: Hold active CH4
1296	955: Hold active CH5
1297	956: Hold active CH6
1298	957: Hold active CH7
1299	958: Hold active CH8
1300	960: Aux. voltage low
1301	961: DiagnosticModule1
1302	962: DiagnosticModule2
1303	963: DiagnosticModule3
1304	964: DiagnosticModule4
1305	965: DiagnosticModule5
1306	966: DiagnosticModule6
1307	967: DiagnosticModule7
1308	968: DiagnosticModule8
1309	969: Modbus Watchdog
1310	970: Curr. input overload
1311	971: Current Input low
1312	972: Curr. input > 20 mA
1313	973: Current Input < 4 mA
1314	974: Diagnostics confirm.
1315	975: Device restart
1316	976: PFM/PWM value high
1317	977: PFM/PWM value low
1318	978: ChemoClean Failsafe
1319	983: Sensor ISE check
1320	984: Process temperature
1321	985: Sensor Interface
1322	987: Calibration required
1323	990: Deviation limit
1324	991: CO2 conc. range
1325	992: pH calculation range
1326	993: rH calculation range
1327	994: Difference conduct.
1328	Date
1329	Time
1330	%H:%M:%S
1331	OK
1332	Maintenance (M)
1333	Out of specification (S)
1334	Function check (C)
1335	Failure (F)
1336	HighestNamurClassFieldbus
1337	Freeze last value
1338	Status only
1339	Config. changed
1340	Baudrate
1341	Not detected
1342	9.6 kBit/s
1343	19.2 kBit/s
1344	31.25 kBit/s
1345	45.45 kBit/s
1346	93.75 kBit/s
1347	187.5 kBit/s
1348	500 kBit/s
1349	1.5 MBit/s
1350	3 MBit/s
1351	6 MBit/s
1352	12 MBit/s
1353	Bus address
1354	DPV0 fault
1355	No fault
1356	Param fault
1357	Config fault
1358	Param & config fault
1359	DPV0 master addr
1360	DPV0 state
1361	Wait for param
1362	Wait for config
1363	Data exchange
1364	DPV0 WDT [ms]
1365	Fieldbus enable
1366	Off
1367	On
1368	Ident number
1369	Automatic
1370	PA-Profile 3.02 (9760)
1371	Liquiline CM44x (155D)
1372	Liquistation CSFxx (155C)
1373	Liquiport CSPxx (155E)
1374	Manufacturer specific
1375	Name of Station
1376	E_FormulaResult_Bool
1377	E_FormulaResult_Float
1378	Fbdp1CardTypeExist
1379	E_EFBDP1TYPE_NO_FBDP1
1380	E_EFBDP1TYPE_FBDP1
1381	E_EFBDP1TYPE_FBDP1_ETHERNET
1382	Alarm delay
1383	Errors are only displayed if they are present for a longer time than specified at this alarm delay setting. This allows to suppress false alarms which might becaused by normal process-related short time deviations.
1384	.0f
1385	s
1386	LowerLimit
1387	UpperLimit
1388	Current output range
1389	0..20 mA
1390	4..20 mA
1391	Failure current
1392	.1f
1393	mA
1394	Via the serial number you can obtain further device data or documentation from the Internet or from your responsible sales office.
1395	Current version
1396	Device tag
1397	Individual device tag, --> "General settings"
1398	__DEFAULT
1399	ExpertMenuPasswordMatches
1400	E_PCR_Undefined
1401	E_PCR_OK
1402	E_PCR_NOK
1403	E_PCR_OK_InExpertMenu
1404	Current order code ext.
1405	Enter the new complete ordercode, which results according the product structure at a change or extension of the device.
1406	Orig. order code ext.
1407	Complete order code resulting from the product structure and how the device was ordered
1408	Order code
1409	You can order identical hardware with this code. This code changes on account of changes to the hardware and you can enter the new code you received from the manufacturer here.
1410	Checksum error
1411	Busy
1412	Framing error
1413	Parity error
1414	Invalid Frames
1415	Valid Frames
1416	Device revision
1417	The device revision can change if the base module is replaced.
1418	Device type
1419	Device code for CM44x, or CSFxx CSPxx
1420	Manufacturer ID
1421	Software revision
1422	The software revision changes when a software update is performed.
1423	Unique address
1424	The unique address is tied to the serial number and serves to address unique devices on a network.
1425	Availability
1426	(Operating time - Time in failure) / Operating time * 100%
1427	%
1428	MTBF
1429	Mean time between failures: (Operating time - Time in failure) / Number of failures
1430	min
1431	h
1432	d
1433	month(s)
1434	MTTR
1435	Mean time to repair: Time in failure / Number of failures
1436	Number of failures
1437	Number of failure diagnostic messages.
1438	Total operating time
1439	The total operating time of the device since commissioning.
1440	Operating time
1441	Time in failure
1442	Operating time with NAMUR F status signal.
1443	Difference
1444	Redundancy
1445	rH calculation
1446	Degassed conductivity
1447	Dual conductivity
1448	pH calculation from conductivity
1449	Cation exchanger capacity
1450	Formula
1451	SensorType_Sensor_CH0
1452	Oxygen (amp.)
1453	Oxygen (opt.)
1454	pH Glass
1455	pH ISFET
1456	ORP
1457	pH/ORP
1458	Cond c
1459	Cond c 4-pol
1460	Cond i
1461	TU/TS
1462	TU
1463	Nitrate
1464	SAC
1465	ISE
1466	Ultrasonic interface
1467	Disinfection
1468	E_SensorFSPH1
1469	E_SensorFSLC1
1470	E_SensorFSLI1
1471	Photometer
1472	TU/AU
1473	Spectrometer
1474	Sw version FMSY1
1475	FMSY1 proj. version
1476	Frequency
1477	Parameter
1478	Static signal
1479	PFM
1480	Fixed value
1481	Ignore
1482	Hold current
1483	Range lower value
1484	Assignment of 0/4 mA value
1485	.2f
1486	.3f
1487	.4f
1488	.5f
1489	.6f
1490	UserUnit
1491	Range lower unit
1492	1/K
1493	nAs
1494	µAs
1495	As
1496	ppb
1497	ppm
1498	%SAT
1499	1/mm
1500	1/cm
1501	1/m
1502	g/kg
1503	ppmVol
1504	%Vol
1505	%/K
1506	%/µV
1507	%/mV
1508	%/V
1509	µS
1510	mS
1511	S
1512	pA
1513	nA
1514	µA
1515	A
1516	nA/(mg/l)
1517	A/(kg/m³)
1518	A/Pa
1519	pA/hPa
1520	A/hPa
1521	°
1522	FNU
1523	NTU
1524	Hz
1525	1/min
1526	1/h
1527	1/d
1528	KByte
1529	mm
1530	cm
1531	dm
1532	m
1533	km
1534	g/ml
1535	µg/l
1536	mg/l
1537	g/l
1538	kg/l
1539	kg/m³
1540	mm/s
1541	mm/min
1542	mm/h
1543	mm/d
1544	Pa
1545	hPa
1546	mbar
1547	Pa/A
1548	PSU
1549	mΩ
1550	Ω
1551	kΩ
1552	MΩ
1553	GΩ
1554	rH
1555	µS/mm
1556	nS/cm
1557	µS/cm
1558	mS/cm
1559	S/cm
1560	µS/m
1561	mS/m
1562	S/m
1563	kS/m
1564	MS/m
1565	nΩm
1566	µΩm
1567	mΩm
1568	Ωm
1569	kΩm
1570	MΩm
1571	GΩm
1572	Ωcm
1573	kΩcm
1574	MΩcm
1575	°C
1576	K
1577	µs
1578	ms
1579	week(s)
1580	l/s
1581	m³/s
1582	l/min
1583	m³/min
1584	l/h
1585	m³/h
1586	l/d
1587	m³/d
1588	µV
1589	mV
1590	V
1591	mV/%
1592	V/%
1593	mV/pH
1594	V/pH
1595	ml
1596	l
1597	m³
1598	inch
1599	ft
1600	yd
1601	mi
1602	in/s
1603	inch/min
1604	inch/h
1605	inch/d
1606	°F
1607	gps
1608	cfs
1609	mgs
1610	gpm
1611	cfm
1612	mgm
1613	gph
1614	cfh
1615	mgh
1616	gpd
1617	cfd
1618	mgd
1619	gal
1620	cf
1621	mol/m³
1622	mol/l
1623	%TS
1624	bar
1625	nm
1626	m/s
1627	ft/s
1628	MByte
1629	Byte
1630	GByte
1631	pA/(mg/l)
1632	kg/mol
1633	g/mol
1634	FTU
1635	TE/F
1636	ASBC
1637	EBC
1638	度
1639	AU
1640	%T
1641	OD
1642	ml/min
1643	eq
1644	eq/m³
1645	eq/l
1646	eq/gal
1647	°C/s
1648	°C/min
1649	FAU
1650	1/Pa
1651	1/hPa
1652	1/MPa
1653	Auto
1654	FloatFormat
1655	Range upper value
1656	Assignment of 20 mA value
1657	Range upper unit
1658	Oxygen (opt. fixed cable)
1659	Oxygen (opt. Memosens coupling)
1660	Disinfection (CCS142D)
1661	Inline photometer
1662	MTBC
1663	Mean time between calibrations: (Operating time - Time in calibration) / Number of calibrations
1664	Number of calibrations
1665	Number of calibrations and/or adjustments.
1666	Time in calibration
1667	Operating time with calibration status.
1668	E_DeviceNotConnected
1669	E_DeviceConnected
1670	E_SourceUninitialized
1671	E_SourceAvailable
1672	E_SourceUnavailable
1673	Current output
1674	Status
1675	Good
1676	Uncertain
1677	Bad
1678	Properties
1679	Simulation
1680	Offset
1681	Initializing
1682	Alarm
1683	PauseMarkedSamplingProgramCommand
1684	E_No
1685	E_Yes
1686	Program name:
1687	Displays the current program name
1688	StartMarkedSamplingProgramCommand
1689	E_Stop
1690	E_Start
1691	E_SaveAndStart
1692	Bottle volume left
1693	Input volume bottles for a bottle on the left side
1694	Bottle volume right
1695	Input volume bottles for a bottle on the right side
1696	Current bottle configuration
1697	Number of sample bottles
1698	1x - PE Direct distribution
1699	2x - PE Direct distribution
1700	4x - PE Direct distribution
1701	4x - Glass Direct distribution
1702	4x - Glass Schott GLS80 Direct distribution
1703	12x - PE Direct distribution
1704	12x - PE/Glass Plate distribution
1705	24x - PE Direct distribution
1706	24x - PE/Glass Plate distribution
1707	6x+1x - PE/Glass Plate distribution
1708	6x+2x - PE+PE Plate distribution
1709	6x+2x - PE+Glass Plate distribution
1710	12x+1x - PE/Glass Plate distribution
1711	12x+2x - PE+PE Plate distribution
1712	12x+2x - PE+Glass Plate distribution
1713	12x+6x - PE Direct distribution
1714	12x+6x - PE/Glass Plate distribution
1715	Program status
1716	Displays the state of the current program
1717	Inactive
1718	Active
1719	Pause
1720	Waiting for pause
1721	Pause (seconds)
1722	Display the pause time in seconds
1723	Dosing volume
1724	Adjust the dosing tube in the dosing chamber to change the dosing volume. The level in the bottle is calculated using the set dosing volume.
1725	Program name
1726	Program
1727	Main value
1728	Concentration liquid
1729	Concentration gaseous
1730	Saturation
1731	Partial pressure
1732	Raw value nA
1733	Raw value μs
1734	disabled
1735	Electrode slot 2
1736	Ammonium
1737	Potassium
1738	Chloride
1739	%0V
1740	Electrode slot 3
1741	Electrode slot 4
1742	UserDefinedAvailable
1743	Current
1744	Main value
1745	Main value + ref.
1746	2x absorption
1747	OUSAF11
1748	OUSAF12
1749	OUSAF21/22
1750	OUSAF44/45
1751	OUSAF46
1752	OUSAF46 (2)
1753	OUSBT66
1754	OUSTF10
1755	MeasurandVisibility
1756	Controlled
1757	Independent
1758	3rd party
1759	Inlet
1760	Aeration/Outlet
1761	Unknown
1762	Rainfall
1763	External event
1764	Armature end position detection
1765	E_SignalSamplerInputBinaryMapIB0
1766	E_SignalSamplerInputBinaryMapIB1
1767	E_SignalSamplerInputBinaryMapIB2
1768	E_SignalSamplerInputBinaryMapIB3
1769	E_SignalSamplerInputBinaryMapIB4
1770	E_SignalSamplerInputBinaryMapIB5
1771	NumberOfAvailableParameters
1772	Temperature_Visible
1773	E_Standard
1774	E_Potable
1775	E_FoodSwitch
1776	TurbidityPresent
1777	Firmware version
1778	Temperature unit
1779	Select temperature unit: °C, °F or K
1780	Refresh parameters
1781	Source of data
1782	Current program:
1783	Bottle volume
1784	Bottle volume right
1785	Number of bottles
1786	Status
1787	Pause time
1788	Actuator control module ...
1789	LED module
1790	Photometer ...
1791	Sample preparation 1 ...
1792	Sample preparation 2 ...
1793	Basic setup
1794	Communication statistics ...
1795	No sensor connected
1796	Diagnostics
1797	HART ...
1798	PROFIBUS ...
1799	PROFINET ...
1800	Device variable 0 ...
1801	Device variable 10 ...
1802	Device variable 11 ...
1803	Device variable 12 ...
1804	Device variable 13 ...
1805	Device variable 14 ...
1806	Device variable 15 ...
1807	Device variable 1 ...
1808	Device variable 2 ...
1809	Device variable 3 ...
1810	Device variable 4 ...
1811	Device variable 5 ...
1812	Device variable 6 ...
1813	Device variable 7 ...
1814	Device variable 8 ...
1815	Device variable 9 ...
1816	Device
1817	Counters since reset
1818	CH1
1819	CH2
1820	CH3
1821	CH4
1822	CH5
1823	CH6
1824	CH7
1825	CH8
1826	Heartbeat operation ...
1827	Menu
1828	Current output 1
1829	Current output 2
1830	Current output 3
1831	Current output 4
1832	Current output 5
1833	Current output 6
1834	Current output 7
1835	Current output 8
1836	Security check
1837	Do you want to cancel the program?
1838	Sampling programs ...
1839	Setup
1840	System information
1841	Environmental monitoring
1842	Dynamic monitoring
1843	Output configuration
1844	GetHealthStatus
1845	Diagnostics list
1846	Details 1
1847	Remedy
1848	Sensor unknown 1. Replace sensor
1849	Sensor defective 1. Replace sensor
1850	Invalid sensor data 1. Check the software compatibility of sensor and transmitter. Update the transmitter and sensor, if applicable 2. Perform Factory default sensor and power cycle sensor afterwards 3. Update the date of the transmitter 4. Replace the sensor
1851	Sensor scan active, please wait
1852	Writing data to sensor failed 1. Repeat writing 2. Replace sensor
1853	Sensor type wrong - The sensor does not fit to the device configuration - The device configuration may be changed to a new sensor type 1. Change to a sensor of configured type 2. Change device configuration to connected sensor
1854	Sensor communication blocked Possible reasons: - connected sensor failed sensor check. - internal software error 1. Replace sensor
1855	Temperature sensor defective 1. Replace sensor
1856	Sensor electronic defective 1. Check sensor connections 2. Replace sensor electronics
1857	Sensor connection defective 1. Check sensor connection
1858	Device initialization active, please wait
1859	Sensor no communication possible reasons: - sensor disconnected - faulty sensor connection - short-circuit in sensor cable - short-circuit in next channel - faulty sensor FW update 1. Check sensor cable connection 2. Check for short-circuit of the cables 3. Replace sensor 4. Update the sensor FW again
1860	The sensor firmware and the device firmware are incompatible. 1. Replace sensor 2. Update device firmware
1861	Reminder interval for next calibration expires soon. Measurement is still possible. 1. Calibrate sensor 2. Check the configuration of the interval at Setup / Inputs / Channel / Extended setup / Calib. settings / Calibration Timer
1862	Reminder interval for next calibration expired. Measurement is still possible. 1. Calibrate sensor 2. Check the configuration of the interval at Setup / Inputs / Channel / Extended setup / Calib. settings / Calibration Timer
1863	Validity of last calibration expired. Date of last calibration of the sensor is too long ago. Measurement is still possible. Possible reasons: - long storage of sensor 1. Calibrate sensor 2. Check the configuration of the calibration validity at Setup / Inputs / Channel / Extended setup / Calib. settings / Calib. expiration date
1864	Validity of last calibration expires soon. Date of last calibration of the sensor is long ago. Measurement is still possible. Possible reasons: - long storage of sensor 1. Calibrate sensor 2. Check the configuration of the calibration validity at Setup / Inputs / Channel / Extended setup / Calib. settings / Calib. expiration date
1865	Sensor TAG control The connected sensor has an invalid TAG or TAG-group 1. Change sensor 2. Use new sensor of same type 3. Deactivate the TAG control at Setup / Inputs / Channel / Extended setup / Tag control
1866	Sensor calibration is active, please wait.
1867	The configured max. number of sterilizations / cleanings / autoclavings is reached. Measurement is still possible. 1. Replace sensor
1868	The configured max. number of sensor cap sterilizations / cleanings / autoclavings is reached. Measurement is still possible. 1. Replace sensor
1869	Channel initialization failed due to internal hardware or software error. No measurement possible. 1. Contact the service.
1870	Sensor cap operating time warning Measurement is still possible The configured limit of the sensor cap operating time is reached. Current values are displayed under DIAG / Sensor information. 1. Replace sensor cap 2. Adjust limit
1871	Sensor calibration alarm max temperature offset exceeded 1. Execute temperature sensor calibration 2. Replace sensor
1872	Sensor calibration alarm min temperature offset exceeded 1. Execute temperature sensor calibration 2. Replace sensor
1873	Max. temperature slope alarm possible reasons: - sensor overaged or defective 1. Check sensor, replace as necessary 2. Repeat the calibration
1874	Min. temperature slope alarm possible reasons: - sensor overaged or defective 1. Check sensor, replace as necessary 2. Repeat the calibration
1875	Sensor glass breakage alarm Glass membrane impedance too low 1. Check glass electrode for cracks 2. Check the temperature of the medium 3. Replace sensor
1876	Sensor glass broken warning Glass membrane impedance low Measurement is still possible until alarm message 1. Check glass electrode for cracks 2. Check the temperature of the medium 3. Replace sensor
1877	Sensor reference alarm Reference impedance too low 1. Check glass electrode for cracks 2. Check the temperature of the medium 3. Replace sensor
1878	Sensor reference failure warning Measurement is still possible until alarm message 1. Check reference electrode for dirt and damages 2. Clean reference electrode/diaphragm 3. Refill reference solution 4. Replace sensor
1879	Sensor glass limit lower value exceeded Glass membrane impedance too low 1. Check the pH sensor, clean as needed 2. Check the configured glass limit value, correct as needed at Setup / Inputs / Kanal / Extended setup/ Diagnostics settings / Glass impedance (SCS) 3. Replace sensor
1880	Sensor glass limit lower value reached Glass membrane impedance low Measurement is still possible until alarm message 1. Check the pH sensor, clean as needed 2. Check the configured glass limit value, correct as needed at Setup / Inputs / Kanal / Extended setup/ Diagnostics settings / Glass impedance (SCS) 3. Replace sensor
1881	Sensor glass limit upper value exceeded Glass membrane impedance too high 1. Check the pH sensor, replace as needed 2. Check the glass limit value, correct as needed 3. Replace sensor
1882	Sensor glass limit upper value reached Glass membrane impedance high 1. Check the pH sensor, clean as needed 2. Check the configured glass limit value, correct as needed at Setup / Inputs / Kanal / Extended setup/ Diagnostics settings / Glass impedance (SCS) 3. Replace sensor
1883	Sensor check Electrode condition bad. Possible reasons: - glass membrane blocked or dry - diaphragm blocked 1. Clean or regenerate sensor 2. Replace sensor
1884	Sensor check Electrode condition still sufficient but close to the limit. Possible reasons: - glass membrane blocked or dry - diaphragm blocked 1. Clean or regenerate sensor soon 2. Replace sensor soon
1885	Sensor leakage current alarm Sensor defective due to abraision or damage 1. Replace sensor
1886	Sensor leakage current warning Sensor defective due to abraision or damage Measurement is still possible until alarm message 1. Replace sensor
1887	Sensor check Sensor power supply bad 1. Check cable connections 2. Replace sensor
1888	Sensor relaxation time underrange Measurement is still possible possible reasons: - high oxygen content - wrong calibration data 1. Repeat calibration 2. Replace sensor cap
1889	Sensor relaxation time overrange Measurement is still possible possible reasons: - low oxygen content - wrong calibration data 1. Repeat calibration 2. Replace sensor cap
1890	Sensor low signal decay 1. Replace sensor cap
1891	Sensor low signal amplitude Measurement is still possible 1. Replace sensor cap
1892	Sensor temperature too low Temperature out of specification 1. Check application 3. Check installation
1893	Sensor temperature too high Temperature out of specification 1. Check application 2. Check installation
1894	Sensor no LED voltage 1. Contact service
1895	Sensor no LED current 1. Contact service
1896	Sensor dynamic failure 1. Contact service
1897	Polarisation warning High conductivity falsifys the measurement by non-linearity because of polarisation. The measurement error increases. possible reasons: - upper measurement range of sensor reached 1. Use sensor with greater cell constant
1898	Sensor check No conductivity indication possible reasons: - sensor in air - sensor defective 1. Check sensor installation 2. Replace sensor
1899	Sensor selftest failure 1. Replace sensor
1900	Conductivity out of meas. Range possible reasons: - sensor with wrong cell constant 1. Use sensor with appr. cell constant
1901	Sensor temperature out of spec. Range 1. Check temperature 2. Check measurement 3. Change sensor type
1902	Sensor check Coil current out of upper range possible reasons: - short circuit at send coil - inductivity too low 1. Replace sensor
1903	Sensor check Send coil current out of lower range possible reasons: - broken send coil - inductivity too high 1. replace sensor
1904	Sensor LED error 1. Replace Sensor
1905	Sensor selftest electronic Analog/digital converter defective 1. Replace Sensor
1906	Sensor check high pollution degree 1. Clean sensor 2. Replace sensor
1907	Sensor data No calibration data available 1. Carry out air-set calibration
1908	Sensor defective Flash lamp defective possible reasons: - humidity in sensor - mechanical shock / vibration 1. Replace sensor
1909	Sensor data No calibration data of sensor, factory settings are used. 1. Check calibration information of sensor 2. Calibrate cell constant
1910	Sensor defective Analog evaluation error 1. Replace sensor
1911	Heavy organic pollution possible reasons: - sensor dirty - high organic load - wrong installation 1. Clean sensor 2. Install cleaning system 3. Check application
1912	Filter change necessary possible reasons: - long operation time - humidity in sensor 1. Contact service for sensor overhaul 2. Replace sensor
1913	Measurement value invalid 1. Check sensor power supply 2. Restart device at Setup / Diagnostics / Restart
1914	Measurement value uncertain possible reasons: - Sensor dirty - Application wrong 1. Clean sensor 2. Check application
1915	No calibration data available possible reasons: - customer calibration data erased 1. Calibrate sensor 2. Chose other data set 3. Use factory calibration data set
1916	Filter change necessary alarm possible reasons: - long operation time - humidity in sensor 1. Contact service for sensor overhaul 2. Replace sensor
1917	Installation factor lower limit Alarm Influence to the measurement value by the installation wall. With non-conductive pipe material and distance < 15 mm the installation factor decreases. Min value: 0.1 possible reason: - too small distance to the wall 1. Check pipe diameter 2. Clean sensor 3. Recalibrate sensor inline
1918	Installation factor upper limit Alarm Influence to the measurement value by the installation wall. With conductive pipe material and distance < 15 mm the installation factor increases. Max value: 5.0 possible reason: - too small distance to the wall 1. Check pipe diameter 2. Clean sensor 3. Recalibrate sensor inline
1919	Sensor data No calibration data of temperature sensor, factory settings are used. 1. Check calibration information of sensor 2. Calibrate temperature sensor
1920	Polarization Warning A too high conductivity solution during the polarization can distort the measured value 1. Review process 2. Check sensor, if necessary replace it with sensor with the proper cell constant
1921	Operating time warning Measurement is still possible The configured limit of operating time > 200 mg/l is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1922	Operating time warning Measurement is still possible The configured limit of operating time < 50 mg/l is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1923	Lamp change recommendated possible reasons: - Lamp operation time reached 1. Contact service to replace lamp
1924	Echo signal lost Sensor received no echo signal within delay time possible reasons: - sensor fouling - sensor in air or inclined installed - sensor defective 1. Clean sensor 2. Check that sensor is immersed 3. Check sensor vertical installation 4. Configure longer delay time for slow scrubber 5. Replace sensor
1925	Sludge level failure Level measurement failed possible reasons: - hardware defective 1. Replace sensor
1926	Turbidity failure Turbidity measurement failed possible reasons: - hardware defective 1. Replace sensor
1927	Wiper failure Wiper not operational possible reasons: - wiper blocked - hardware defective 1. Clean wiper 2. Replace sensor
1928	Operating time warning Measurement is still possible The configured limit of operating time > 100 nA is reached 1. Replace sensor 2. Adjust limit
1929	Operating time warning Measurement is still possible The configured limit of operating time > 20 nA is reached 1. Replace sensor 2. Adjust limit
1930	Operating time warning Measurement is still possible The configured limit of operating time > 15 °C is reached 1. Replace sensor 2. Adjust limit
1931	Operating time warning Measurement is still possible The configured limit of operating time >300 mV is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1932	Operating time warning Measurement is still possible The configured limit of operating time < -300 mV is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1933	Operating time warning Measurement is still possible The configured limit of operating time with decay time < 25 µs is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1934	Operating time warning Measurement is still possible The configured limit of operating time with decay time > 40 µs is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1935	Operating time warning Measurement is still possible The configured limit of operating time > 15 nA is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1936	Operating time warning Measurement is still possible The configured limit of operating time > 30 nA is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1937	Operating time warning Measurement is still possible The configured limit of operating time > 50 nA is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1938	Operating time warning Measurement is still possible The configured limit of operating time > 160 nA is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1939	Operating time warning Measurement is still possible The configured limit of operating time > 80 °C and < 100 nS/cm is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1940	Operating time warning Measurement is still possible The configured limit of operating time < 5 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1941	Operating time warning Measurement is still possible The configured limit of operating time > 5 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1942	Operating time warning Measurement is still possible The configured limit of operating time > 25 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1943	Operating time warning Measurement is still possible The configured limit of operating time > 30 °C is reached 1. Replace sensor 2. Adjust limit
1944	Operating time warning Measurement is still possible The configured limit of operating time > 40 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1945	Operating time warning Measurement is still possible The configured limit of operating time > 80 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring
1946	Operating time warning Measurement is still possible The configured limit of operating time > 100 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1947	Operating time warning Measurement is still possible The configured limit of operating time > 120 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1948	Operating time warning Measurement is still possible The configured limit of operating time > 125 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1949	Operating time warning Measurement is still possible The configured limit of operating time > 140 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1950	Operating time warning Measurement is still possible The configured limit of operating time > 150 °C is reached 1. Replace sensor 2. Adjust limit 3. Deactivate monitoring at Setup / Inputs / Channel / Extended Setup / Diagnostics settings / Limits operating hours
1951	Operating time warning Measurement is still possible The configured limit of operating time is reached. Current values are displayed under DIAG / Sensor information. 1. Replace sensor 2. Adjust limit
1952	Selftest active, please wait
1953	Simulation active, please wait. Simulation can be stopped in the diagnostic menu, or by restarting the device
1954	Hold active, please wait. Operation mode with modified measurement output Output and status of all channels on hold
1955	Software failure - internal 1. Please update software 2. Please exchange backplane board 3. Please contact service and report the indicated number
1956	Firmware incompatible 1. Check firmware version 2. Update firmware
1957	Firmware failure - internal 1. Update software 2. Replace backplane board 3. Contact service and report the indicated number
1958	Electronics module defective 1. Restart software at Setup / Diagnostics / Restart 2. Check electronics module 3. Replace electronics module
1959	Electronics module no communication 1. Check module connection 2. Replace electronics module 3. Check internal cable to module
1960	Incompatibility detected The device configuration does not match to the parameterization. 1. Check device settings 2. Check electronic module type
1961	Firmware update successfully done
1962	Firmware update failure possible reasons: - reading error - SD card defective - wrong firmware on SD card 1. Repeat update 2. Use different storage medium with firmware 3. Check storage medium for correct firmware
1963	Battery of real time clock low The battery is on the backplane. In case of power outage time and date will be lost. 1. Replace battery
1964	At least one module has incomplete configuration data 1. Check module data
1965	The overall power consumption of the device is too high. 1. Check installation 2. Remove sensor / modules 3. Restart device at Setup / Diagnostics / Restart
1966	Internal Firmware failure Device configuration does not match firmware 1. Contact service
1967	Temperature measurement of sample room with PT1 in climate module not possible. No control of sample room temperature possible. Sampling still active. 1. Check PT1 connector X10 2. Check PT1 to 1000 Ohm 3. Restart device at Setup / Diagnostics / Restart 4. Replace FMSY1 module
1968	Temperature sensor PT2 in sampling room defective. No measurement of sample temperature. Sampling still active. 1. Replace sensor
1969	Temperature sensor PT3 of ambient temperature defective. No control of winter operation possible. For freezing protection are sampling and distribution lever locked. 1. Deactivate winter operation mode at Setup / Inputs / Temperature S.3 / winter operation 2. Replace sensor
1970	Liquidsensor safety cutoff LF2 activated. Fouling of liquidsensor LF1 for sample detection. Sampling still active. 1. Clean sample detection sensor LF1 in dosing chamber
1971	No sample flow Underpressure at peristaltic pump not possible. 1. Check pump tubing 2. Check suction line in sample stream
1972	Sampleroom temperature set point not reached. Refrigeration control not possible. 1. Check sample room door 2. Test climate module under Diagnostics / System test / Cooling system / check cooling
1973	Sampleroom temperature set point not reached. Heating control not possible. 1. Check sample room door 2. Test climate module under Diagnostics / System test / Cooling system / check heating
1974	Fouling of liquidsensor LF1. Still five samples possible. 1. Clean sample detection sensor LF1 in dosing chamber
1975	Liquidsensor LF1 for sample detection defective. No sampling possible. 1. Contact service
1976	Sensor Fouling of liquidsensor LF2. Still five samples possible. 1. Clean sensor LF2 in dosing chamber
1977	Liquid sensor safety cuttoff LF2 defective. No sampling possible 1. Contact service
1978	Capacitive liquid sensor defective. No sample detection in dosing chamber. No sampling possible. 1. Clean sensor 2. Replace sensor
1979	Read sub-program failure It is impossible to read the selected sub-program from the memory. 1. Create a new sub-program
1980	Write sub-program failure It is impossible to write the new sub-program to the memory. - Hardware error occurred 1. Contact service
1981	Delete sub-program failure It is impossible to delete the sub-program from memory. 1. Restart device at Setup / Diagnostics / Restart
1982	Read sub-program list It is impossible to read the sub-program list from the memory. 1. Reset software
1983	Membrane pump failure - Power supply of pump missing - Membrane pump defective - Motor cable broken 1. Check power cable connector X7
1984	Air-manager for pressurized air defective. - Photoelectric sensor failed - Cable air-manger broken 1. Contact service
1985	Distribution arm reference run failed. 1. Run distribution arm test at Diagnostics / System test / Distribution arm 2. Check distribution arm for blockage
1986	Pump motor draws overcurrent 1. Contact service
1987	Control of membrane pump defective 1. Contact service
1988	Peristaltic pump failure - Peristaltic pump defective - Motor cable broken 1. Contact service
1989	Peristaltic pump failure - Control of peristaltic pump defective 1. Contact service
1990	Sample detection failure. No sampling possible. Possible reasons: - sample suction line not empty before sampling - liquid sensor defective 1. Check sample suction line, purge with pump test in diagnostics menu if necessary at Diagnostics / System test / pump test
1991	Climate module defective 1. Replace climate module
1992	Upper ventilator defective. Heat dissipation at condenser is not working. 1. Replace ventilator 2. Contact service department
1993	Pump hose warning - Max. operation time of pump hose reached soon - Display at Diagnostics / Operating time information 1. Plan replacement of pump hose. After replacement reset timer of pump hose.
1994	Max. operating time of pump hose reached. Display at Diagnostics / Operating time information. 1. Replace pump hose. After replacement reset timer of pump hose.
1995	Fouling of liquidsensor LF1 warning 1. Clean sensor LF1 within a short time. 2. The sensitivity can be configured at Setup / General Settings / Sampling / conductive sensor
1996	Fouling of liquidsensors LF1 detected 1. Clean sensor LF1 2. The sensitivity can be configured at Setup / General Settings / Sampling / conductive sensor
1997	Power supply loss
1998	Program pause - Sampling program paused.
1999	Summertime / wintertime changeover Normaltime (wintertime) active
2000	Summertime / wintertime changeover Summertime active
2001	No Sampling confirmation - Sampling command was not processed. 1. Check internal connection cable to 1IF 2. Reset firmware
2002	It is impossible to read the selected program from the memory. 1. Create a new program
2003	It is impossible to write the new program to the memory. - Hardware error occurred 1. Contact service
2004	Uninterruptible power supply warning Battery status low 1. Check battery connectors 2. Replace battery 3. Check battery charger, replace as necessary
2005	Delete program It is impossible to delete the program from memory. 1. Reset software
2006	Read program list failure It is impossible to read the program list from the memory. 1. Reset software at Diagnostics / System test/Reset / device reset
2007	Overfill check The total volume of the bottle is reached. - No further sample is taken into the current bottle. 1. If desired adjust sampling program at Select sampling program / <program name>
2008	Bottle check No empty bottles available for the current program. - No further sampling. 1. Check program settings at Select sampling program / <program name>
2009	Start time over - The selected start time is in the past. 1. Enter a new start time.
2010	Overfill check Total sample volume does not fit into bottle. 1. Change sample volume.
2011	Sampling faulted because of too many sample requests cueing. 1. If desired adjust sampling program at Select sampling program / <program name>
2012	Program configuration differs from the current settings. 1. Change configuration
2013	Error during bottle emptying. The emptying and the sample program is aborted. 1. Check connection to FMSY1 module 2. Check 4R module, replace as necessary 3. Restart device at Setup / Diagnostics / Restart
2014	Reserved
2015	Internal voltage out of range 1. Check supply voltage 2. Check connected inputs and outputs for short-circuit
2016	The temperature of the backplane electronics is high 1. Check ambient temperature and energy consumption
2017	Sensor sequence counter Measurement signal from sensor missing 1. Check sensor, replace as necessary 2. Check sensor connection
2018	No connection to the 4R module 1. Check 4R module, replace as necessary 2. Restart device at Setup / Diagnostics / Restart
2019	Reset to factory defaults
2020	Device verification active, please wait
2021	Service switch is switched on. The device can be addressed at IP address 192.168.1.212. Switch service switch off to change back to configured IP settings. 1. Deactivate service IP
2022	The calibration has been aborted.
2023	Mathematical function in fault condition 1. Check mathematical function 2. Check assigned input variables
2024	Current output below limit Measurement value out of spec. range possible reasons: - sensor / sample line in air - air cushion in assembly - wrong sensor inflow - sensor / sample line dirty 1. Check application 2. Check the current output parameterization 3. Clean sensor / sample line
2025	Current output above limit Measurement value out of spec. range possible reasons: - sensor / sample line in air - air cushion in assembly - wrong sensor inflow - sensor / sample line dirty 1. Check application 2. Check configuration of current output 3. Clean sensor / sample line
2026	Sensor calibration aborted Main measurement value fluctuating possible reasons: - sensor overaged - sensor temporary dry - buffer solution value not stable 1. Check sensor, replace as necessary 2. Check buffer solution
2027	Sensor calibration aborted Temperature measurement value fluctuating possible reasons: - sensor overaged - sensor temporary dry - temperature of buffer not stable 1. Check sensor, replace as necessary 2. Check buffer temperature
2028	No text catalog installed 1. Contact service
2029	Language change failure Selected language not installed 1. Contact service
2030	Max. zero point (pH/Disinfection (Di)/DO) / offset (ORP) warning Measurement is still possible until alarm message. Possible reasons: - sensor aged or defective - pH/ORP: diaphragm blocked - pH/ORP: buffer solution expired or contaminated - Di/DO: electrolyte consumed - Di/DO: sensor pin damaged 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat calibration
2031	Min. zero point (pH/Disinfection (Di)/DO) / offset (ORP) warning Measurement is still possible until alarm message. Possible reasons: - sensor aged or defective - pH/ORP: diaphragm blocked - pH/ORP: buffer solution expired or contaminated - Di/DO: electrolyte consumed - Di/DO: sensor pin damaged 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat calibration
2032	Min. slope warning Measurement is still possible until alarm message possible reasons: - sensor aged or defective - diaphragm blocked - buffer solution expired or contaminated 1. Check sensor, replace as necessary 2. Check buffer, replace as necessary 3. Repeat the calibration
2033	Max. slope warning Measurement is still possible until alarm message possible reasons, depending on sensor type: - sensor aged or defective - diaphragm blocked - buffer solution expired or contaminated - electrolyte consumed - sensor pin damaged 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat the calibration
2034	Zero point warning possible reasons, depending on sensor type: - sensor aged or defective - diaphragm blocked - buffer solution expired or contaminated - electrolyte consumed - sensor pin damaged 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat the calibration
2035	Max. operation point warning Measurement is still possible until alarm message possible reasons: - sensor aged or defective - diaphragm blocked - buffer solution expired or contaminated 1. Check sensor, replace as necessary 2. Check buffer, replace as necessary 3. Repeat the calibration
2036	Min. operation point warning Measurement is still possible until alarm message possible reasons: - sensor aged or defective - diaphragm blocked - buffer solution expired or contaminated 1. Check sensor, replace as necessary 2. Check buffer, replace as necessary 3. Repeat the calibration
2037	Delta slope warning Measurement is still possible. The calibration shows a large change of sensor slope. 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat calibration
2038	Delta zero point warning Measurement is still possible. The calibration shows a large change of sensor zero point. 1. Check sensor, replace as necessary 2. Check buffer or electrolyte, replace as necessary 3. Repeat calibration
2039	Delta working point warning Measurement is still possible The calibration shows a large change of sensor working point 1. Check sensor, replace as necessary 2. Check buffer, replace as necessary 3. Repeat calibration
2040	Diagnostic behaviour setup active for maintenance 1. Wait for end of maintenance
2041	Logbook filled 80% 1. Save logbook to SD-card and empty it at Diagnostics / Logbooks / Save logbooks. Than Diagnostics / Logbooks / / delete all entries 2. Change logbook type to ringbuffer at Setup / General Settings / Logbooks
2042	Logbook filled 100% - no more entries possible 1. Save logbook to SD-card and empty it at Diagnostics / Logbooks / Save logbooks. Than Diagnostics / Logbooks / / delete all entries 2. Change logbook type to ringbuffer at Setup / General Settings / Logbooks 3. Deactivate logbook
2043	Electrolyte consumption warning The configured limit of electrolyte consumption is reached. Measurement is still possible. 1. Replace electrolyte and if applicable membrane cap. Reset counters at CAL / Change electrolyte or change sensor cap and electrolyte. 2. Replace sensor
2044	The configured max. number of sensor cap calibrations reached Measurement is still possible. 1. Replace sensor cap
2045	SD card filled 80% 1. Replace SD card with empty SD card 2. Empty SD card 3. Change logbook type to ringbuffer at Setup / General Settings / Logbooks
2046	SD card filled 100% - no more entries possible 1. Replace SD card with empty SD card 2. Empty SD card 3. Change logbook type to ringbuffer at Setup / General Settings / Logbooks 4. Deactivate logbook
2047	SD card missing 1. Check SD card 2. Replace SD card 3. Deactivate logging
2048	Save of device configuration failed
2049	Load of device configuration successful
2050	Load of device configuration failed
2051	Load of device configuration aborted
2052	Reset device configuration to factory default succsessful
2053	Reset device configuration to factory default failed
2054	Concentration measurement: Process temperature below concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2055	Concentration measurement: Process temperature above concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2056	Concentration measurement: Process conductivity below concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2057	Concentration measurement: Process conductivity above concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2058	Concentration measurement: Process concentration below concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2059	Concentration measurement: Process concentration above concentration table possible reasons: - process value out of specification If custom table: - concentration table not complete 1. Expand concentration table at Setup / Inputs / CHx cond ind / edit table
2060	Conductivity measurement: Process temperature below compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2061	Conductivity measurement: Process temperature above compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2062	Conductivity measurement: Process conductivity below compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2063	Conductivity measurement: Process conductivity above compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2064	Conductivity measurement: conductivity compensation below compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2065	Conductivity measurement: conductivity compensation above compensation table possible reasons: - process value out of specification - compensation table not complete 1. Expand compensation table at Setup / Inputs / CHx cond ind / edit table
2066	Incompatible model package Output configuration and parameter settings have been automatically reset 1. Check the configuration of the corresponding outputs, the measurement settings and the configuration of the application calibration
2067	Membrane cap change necessary possible reasons: - long operation time 1. Replace membrane cap and switch membrane timer off/on to reset the membrane timer under Setup / Inputs / Extended setup
2068	Sensor reference limit upper value exceeded Reference membrane impedance too high 1. Check the sensor, replace as needed 2. Check the reference limit value, correct as needed 3. Replace sensor
2069	Sensor reference limit upper value reached Reference membrane impedance high 1. Check the sensor, replace as needed 2. Check the reference limit value, correct as needed 3. Replace sensor
2070	Min. calibration quality warning Measurement is still possible. The calibration quality shows a large change since last calibration. 1. Repeat calibration 2. Check sensor, replace as necessary
2071	Sensor defective Internal sensor connection broken 1. Replace sensor 2. Contact service
2072	Sensor deactivated Sensor has been deactivated by user. 1. Replace sensor
2073	Lamp change alarm possible reasons: - configured operation time reached 1. Contact service to replace lamp
2074	Lamp change warning possible reasons: - remaining lamp intensity low - lamp life not reset after replacement 1. Replace lamp and reset lamp life 2. Contact service
2075	Lamp change alarm possible reasons: - remaining lamp intensity too low - lamp life not reset after replacement 1. Replace lamp and reset lamp life 2. Contact service
2076	Lamp defective possible reasons: - cable defective - lamp defective 1. Check cable 2. Replace lamp and reset lamp life 3. Contact service
2077	Out of temperature range 1. Check application 2. Check sensor
2078	Process value out of operating range 1. Check application 2. Check sensor
2079	Process value too high Process value out of spec. range possible reasons: - Sensor in air - Air cushion in assembly - Wrong sensor installation - Sensor defective 1. Decrease process value 2. Check measurement 3. Change sensor type
2080	Process value too low Process value out of spec. range possible reasons: - Sensor in air - Air cushion in assembly - Wrong sensor installation - Sensor defective 1. Increase process value 2. Check measurement 3. Change sensor type
2081	Process value out of spec. range possible reasons: - Sensor in air - Air cushion in assembly - Wrong sensor installation - Sensor defective 1. Check process value 2. Check measurement 3. Change sensor type
2082	No sampling The flow is too low for flow proportional sampling. 1. Check sample stream 2. Check flow meter 3. Check configuration at Setup / Inputs / Current input S:x
2083	Process check system alarm Measurement signal long time without variation possible reasons: - sensor blocked or in air - no sensor inflow - sensor defective - software failure 1. Check application 2. Check measurement line 3. Check sensor
2084	Cation exchanger failure Wrong values of conductivity or flow, see additional information of diagnostic message 1. Check for in mathematic menu 'cation exchanger' if all measurement values are valid 2. Check connected sensors 3. Check for minimum flow
2085	Cation exchanger warning Exceeded limit values of conductivity or flow, see additional information of diagnostic message. possible reason: - resin exhausted - piping obstructed 1. Check application
2086	Cation exchanger capacity low 1. Schedule resin regeneration
2087	Cation exchanger capacity exhausted 1. Regenerate resin
2088	Limit switch activated
2089	USP / EP alarm conductivity limit for USP or EP exceeded 1. Check process
2090	USP / EP warning Conductivity value close to the limit for USP or EP 1. Check process
2091	No sample flow during dosing process possible reasons: - Suction line blocked or leaky - No sample flow 1. Check suction line and if appropriate strainer 2. Check sample stream
2092	Pump bracket open The pump bracket is detected as open possible reasons: - Pump bracket open - Faulty reed contact 1. Close pump bracket 2. Contact service
2093	Life time of o-ring seal on inline armature reached within a short time. Display at Diagnostics / Operating time information / inline armature 1. Replace o-ring seal 2. Deaktivate monitoring at Setup / General settings / Sampling / Diagnostics settings / Process sealing 3. Contact service
2094	Life time of o-ring seal on inline armature is reached. Display at Diagnostics / Operating time information / inline armature 1. Replace o-ring seal 2. Deaktivate monitoring at Setup / General settings / Sampling / Diagnostics settings / Process sealing 3. Contact service
2095	Both proximity probes on the inline armature send an end position reached signal (pair failure). possible reasons: - proximity probes defective - supply line defective 1. Check probes 2. Check supply line of probes
2096	Sampling end position (in process) not reached or not detected. possible reasons: - Armature blocked - Proximity probes defective - Supply line defective 1. Check inline armature 2. Check probes 3. Check supply line of probes
2097	Dosing end position (out of process) not reached or not detected. possible reasons: - Armature blocked - Proximity probes defective - Supply line defective 1. Check inline armature 2. Check probes 3. Check supply line of probes
2098	Winter operation - Winter operation enabled. - Ambient temperature too low. - No sampling possible.
2099	No sampling Suction of sample not possible. - Suction line or straine blocked - Suction lift too high 1. Check suction line and strainer. 2. Assure appropriate suction lift (<8m)
2100	Input signal faulty - sensor changed - sensor nonexistent 1. Check measurement inputs
2101	Sample flow faulty possible reasons: - Suction line blocked or leaky - Sample flow too low - Sample flow too high 1. Check suction line and if appropriate strainer 2. Check sample stream
2102	Process temperature high 1. No temperature increase 2. Check measurement 3. Change sensor type
2103	Process temperature low 1. No temperature decrease 2. Check measurement 3. Change sensor type
2104	Controller input warning Controlled variable status is invalid. 1. Check application
2105	Controller input warning Setpoint status is invalid. 1. Check application
2106	Controller input warning Disturbance variable status is invalid. 1. Check application
2107	Process value high possible reasons: - Sensor in air - Air cushion in assembly - Wrong sensor installation - Sensor defective 1. No process value increase 2. Check measurement 3. Change sensor type
2108	Process value low possible reasons: - Sensor in air - Air cushion in assembly - Wrong sensor installation - Sensor defective 1. No process value decrease 2. Check measurement 3. Change sensor type
2109	Process at the edge of the dynamic range of the sensor. Possible reason: - change of the application to a higher or lower measurement range 1. Check application 2. Use a sensor suitible to the measurement range of the application
2110	Max. pH range warning 1. Check application 2. Check pH Sensor
2111	Min. pH range warning. Possible escape of gaseous chlorine. 1. Check application 2. Check pH Sensor
2112	Hold active Output and status of channel 1 on Hold
2113	Hold active Output and status of channel 2 on Hold
2114	Hold active Output and status of channel 3 on Hold
2115	Hold active Output and status of channel 4 on Hold
2116	Hold active Output and status of channel 5 on Hold
2117	Hold active Output and status of channel 6 on Hold
2118	Hold active Output and status of channel 7 on Hold
2119	Hold active Output and status of channel 8 on Hold
2120	Auxiliary voltage low 1. Check cables and connected devices 2. Check connector for shortcut
2121	Diagnostic module 1 activated
2122	Diagnostic module 2 activated
2123	Diagnostic module 3 activated
2124	Diagnostic module 4 activated
2125	Diagnostic module 5 activated
2126	Diagnostic module 6 activated
2127	Diagnostic module 7 activated
2128	Diagnostic module 8 activated
2129	Modbus timeout watchdog The device did not receive a modbus request of the master within the specified timeout. The status of received modbus process values is set to 'bad'.
2130	Current input signal overloaded The current input is switched off due to overload and reactivated automatically at normal load. 1. Check the connected device, the cable and the connector
2131	Current input low With 4-20 mA input configuration the input current is below the lower failure current 1. Check the connected device, the cable and the connector for short circuit
2132	Current input signal above high setpoint The connected device delivers failure current
2133	Current input signal below low setpoint Connected device sets failure current
2134	The diagnostic message displayed in a measurement view was confirmed by a user. No diagnostic message will be displayed in any measurement view until the next diagnostic message is set.
2135	Device reset, wait.
2136	Pulse frequency/width modulation Output signal exceeded Measurement value out of spec. range possible reasons: - sensor in air - air cushion in assembly - wrong sensor inflow - sensor dirty 1. Clean sensor 2. Check plausibility 3. Adjust PFM/PWM output signal
2137	Pulse frequency/width modulation Output signal too low Measurement value out of spec. range possible reasons: - sensor in air - air cushion in assembly - wrong sensor inflow - sensor dirty 1. Clean sensor 2. Check plausibility 3. Adjust PFM/PWM output signal
2138	ChemoClean Plus Failsafe Status No feedback signal within the configured duration time detected. 1. Check application 2. Check wiring 3. Enlarge duration time
2139	Sensor ISE check possible reasons: - Electrode defective - Membrane defective 1. Check electrode, replace as necessary 2. Check membrane cap, replace as necessary
2140	Process temperature out of specified range 1. Check process temperature 2. Check measurement
2141	Sensor interface failure possible reasons: - Connection to sensor faulty 1. Check connector 2. Check cable, replace as necessary
2142	Due to a sensor maintenance a calibration is required.
2143	Measurement redundancy: The limit of the percentage deviation is exceeded.
2144	CO2 concentration out of range.
2145	pH calculation out of range.
2146	rH calculation out of range.
2147	Difference conductivity out of range.
2148	Details 2
2149	Details 3
2150	Details 4
2151	Details 5
2152	Details 6
2153	Details 7
2154	Details 8
2155	Details 9
2156	Details 10
2157	Hart diagnostics
2158	Status byte 0
2159	Status byte 1
2160	Status byte 15
2161	Status byte 16
2162	Status byte 17
2163	Status byte 18
2164	Status byte 19
2165	Status byte 20
2166	Status byte 21
2167	Status byte 22
2168	Device variable 0
2169	Device variable 10
2170	Device variable 11
2171	Device variable 12
2172	Device variable 13
2173	Device variable 14
2174	Device variable 15
2175	Value on curr 1
2176	Value on curr 2
2177	Value on curr 3
2178	Value on curr 4
2179	Device variable 1
2180	Value on curr 5
2181	Value on curr 6
2182	Value on curr 7
2183	Value on curr 8
2184	Loop current 1
2185	Loop current 2
2186	Loop current 3
2187	Loop current 4
2188	Loop current 5
2189	Loop current 6
2190	Device variable 2
2191	Loop current 7
2192	Loop current 8
2193	Device variable 3
2194	Device variable 4
2195	Device variable 5
2196	Device variable 6
2197	Device variable 7
2198	Device variable 8
2199	Device variable 9
2200	Primary variable
2201	Quaternary variable
2202	Secondary variable
2203	Tertiary variable
2204	Line recorder
2205	Device variables
2206	Device variable values
2207	Dynamic variables
2208	Dynamic variables values
2209	Process Variables
2210	Measured values
2211	Measured values
2212	Reset configuration changed flag
2213	Liquistation CSFxx
2214	Failure
2215	Failure- 'F'(Condensed Status): When this value is set, this indicates one or more Device Variables (i.e., measurement or control values) are invalid due to a malfunction in the field device or its peripherals.
2216	Out of Specification
2217	Out of Specification- 'S'(Condensed Status): When this value is set, this indicates deviations from the permissible ambient or process conditions have been detected that may compromise measurement or control accuracy (i.e., device performance may be degraded given current operating conditions).
2218	Function Check
2219	Function Check- 'C'(Condensed Status): When this value is set, this indicates one or more Device Variables are temporarily invalid (e.g. frozen) due to ongoing work on the device.
2220	Device Configuration Locked
2221	Sensor channel 1 error
2222	Sensor channel 2 error
2223	Sensor channel 3 error
2224	Sensor channel 4 error
2225	Sensor channel 5 error
2226	Sensor channel 6 error
2227	Sensor channel 7 error
2228	Sensor channel 8 error
2229	Global error
2230	Initialization or maintenance active, please wait
2231	Device failure, service necessary
2232	Device maintenance, service necessary
2233	Calibration active, please wait
2234	Battery empty, change battery of clock
2235	Analog input out of spec. range
2236	Analog output out of spec. range
2237	Alarm, measurement value failure, check application
2238	Warning, measurement value failure, check application
2239	Alarm, temperature failure, check application
2240	Warning, temperature failure, check application
2241	Alarm, process check system, no change of measurement value
2242	Logbook memory, check logbook
2243	No sample flow, service necessary
2244	No cooling, service necessary
2245	No heating, service necessary
2246	Opt. Inspection, replace hoses / sealing
2247	Present / all bottles full, no further sampling
2248	Alarm, no module communication
2249	Sensor communication, check connection
2250	Alarm, sensor failure, service necessary
2251	Alarm, replace wear part
2252	Warning, replace wear part
2253	Alarm, clean or replace sensor
2254	Calibration necessary
2255	Replace temperature sensor
2256	Alarm, calibration timer expired
2257	Warning, calibration timer expires soon
2258	Warning, temperature calibration expires soon
2259	Calibration failure, repeat calibration
2260	Warning, operation time
2261	Alarm, sensor glass membrane
2262	Warning, sensor glass membrane
2263	Alarm, sensor reference
2264	Warning, sensor reference
2265	Alarm, sensor leak current
2266	Warning, sensor leak current
2267	Alarm, low sensor signal
2268	Warning, low sensor signal
2269	Alarm, ISE check
2270	Alarm, USP / EP
2271	Warning, USP / EP
2272	Calculation overflow
2273	Redundancy deviation
2274	Set default failed
2275	File operation fail
2276	License error
2277	Calibration aborted
2278	Power fail
2279	Sampler is paused
2280	Diagnostics menu selected
2281	Hold active
2282	Simulation active
2283	Status
2284	Update period
2285	Unit device variable 0
2286	us
2287	uA
2288	MOhm
2289	Unit device variable 1
2290	Unit device variable 2
2291	Unit device variable 3
2292	Unit device variable 4
2293	Unit device variable 5
2294	Unit device variable 6
2295	Unit device variable 7
2296	Unit device variable 8
2297	Unit device variable 9
2298	dummy_SerialNumber
2299	dummy_float
2300	Liquistation CSFxx (Rev.2)
2301	Locking state
2302	Process-/Measured values
2303	Device information
2304	No command specific errors
2305	WARNING
2306	Too few data bytes received
2307	Device specific command error
2308	Access restricted
2309	Busy
2310	Invalid selection
2311	In write protect mode
2312	Device variable 0
2313	Device variable 1
2314	Device variable 2
2315	Device variable 3
2316	Device variable 4
2317	Device variable 5
2318	Device variable 6
2319	Device variable 7
2320	Device variable 8
2321	Device variable 9
2322	Device variable 10
2323	Device variable 11
2324	Device variable 12
2325	Device variable 13
2326	Device variable 14
2327	Device variable 15
2328	Value on curr 1
2329	Loop current 1
2330	Loop current 2
2331	Loop current 3
2332	Loop current 4
2333	Loop current 5
2334	Loop current 6
2335	Loop current 7
2336	Loop current 8
2337	Device variable 0
2338	MOhm*cm
2339	Value on curr1
2340	Value on curr 3
2341	Value on curr 4
2342	Value on curr 5
2343	unit of Loop current 1
2344	unit of Loop current 2
2345	unit of Loop current 3
2346	unit of Loop current 4
2347	unit of Loop current 5
2348	unit of Loop current 6
2349	unit of Loop current 7
2350	unit of Loop current 8
2351	Battery life (float in days)
2352	unit of Battery life (float in days)
2353	Percent range
2354	unit of Percent range
2355	Loop current
2356	unit of Loop current
2357	3.0f
2358	milliseconds
2359	OK
2360	Device failure
2361	Function check
2362	Maintenance required
2363	Out of specification
2364	Number of the highest priority error
2365	Status programa
2366	Inativo
2367	Ativo
2368	Pausa
2369	Aguardando pausa
2370	Versão Firmware
2371	Versão hardware
2372	Código
2373	Núm. de série
2374	Unidade Temperatura
2375	Atraso do Hold
2376	-
2377	%Sat
2378	A/(kg/m3)
2379	kB
2380	kg/m3
2381	psu
2382	mO
2383	O
2384	kO
2385	MO
2386	GO
2387	nOm
2388	µOm
2389	mOm
2390	Om
2391	kOm
2392	MOm
2393	GOm
2394	Ocm
2395	kOcm
2396	MOcm
2397	week
2398	month
2399	m3/s
2400	m3/min
2401	m3/h
2402	m3/d
2403	m3
2404	mol/m3
2405	in
2406	in/min
2407	in/h
2408	in/d
2409	gal/s
2410	(cu ft)/s
2411	Mgal/s
2412	gal/min
2413	(cu ft)/min
2414	Mgal/min
2415	gal/h
2416	(cu ft)/h
2417	Mgal/h
2418	gal/d
2419	(cu ft)/d
2420	Mgal/d
2421	cu ft
2422	Descrição
2423	Language
2424	English
2425	Chinese (simplified)
2426	Czech
2427	Dutch
2428	French
2429	German
2430	Italian
2431	Japanese
2432	Polish
2433	Portuguese
2434	Russian
2435	Spanish
2436	Swedish
2437	Turkish
2438	Mensagem mais importante
2439	Progresso
2440	Esperando
2441	Iniciar refere.
2442	Braço distr. posicionado
2443	Processo de purga
2444	Processo de sucção
2445	Sensor detectado
2446	Processo dosagem
2447	Sucesso
2448	Falha de amostra
2449	Retardo de amostragem
2450	Amostra
2451	Pré lavagem
2452	Pós lavagem
2453	Launch bottle
2454	Versão software
2455	Nome do programa
2456	Número de Série
2457	Versão SW FMSY1
2458	First op. time date
2459	First op. time hour
2460	First op. time minute
2461	TAG
2462	Erro corrente
2463	Grupo de TAG
2464	Contraste
2465	Volume da garrafa direita
2466	StartMarkedSamplingProgramCommand
2467	Rotação de tela
2468	Manual
2469	Automatico
2470	Volume dosagem
2471	Set date
2472	Set hour
2473	Set minute
2474	Menu de calibração
2475	Desabilitar
2476	Habilitado
2477	Núm. de garrafas atual
2478	Screensaver
2479	Desligado
2480	Automático
2481	Detector de líquido
2482	Automático
2483	Semi-automático
2484	Range de saída atual
2485	0..20 mA
2486	4..20 mA
2487	Equip. amostrador
2488	Peristáltica
2489	Vácuo
2490	En linha
2491	FMSY1 proj. version
2492	Menu Setup
2493	Configuração de garrafa atual
2494	1x - PE Distribuição direta
2495	2x - PE Distribuição direta
2496	3x - PE Distribuição direta
2497	4x - Vidro distribuição direta
2498	12x - PE Distribuição direta
2499	12x - PE/Vidro Distribuição placa
2500	24x - PE Distribuição direta
2501	24x - PE/Vidro Distribuição placa
2502	6x+1x - PE/Vidro Distribuição placa
2503	6x+2x - PE+PE Placa distribuição
2504	6x+2x - PE+Vidro Placa distribuição
2505	12x+1x - PE/Vidro Distribuição placa
2506	12x+2X - PE+PE Distrib. placa
2507	12x+2x - PE+Vidro Distribuição placa
2508	12 +6x - PE Distribuição direta
2509	12x+6X - PE+Vidro Distrib. placa
2510	Classe equip.
2511	Garrafas livres
2512	Frente
2513	Garrafa 1
2514	Garrafa 2
2515	Garrafa 3
2516	Garrafa 4
2517	Garrafa 5
2518	Garrafa 6
2519	Garrafa 7
2520	Garrafa 8
2521	Garrafa 9
2522	Garrafa 10
2523	Garrafa 11
2524	Garrafa 12
2525	Garrafa 13
2526	Garrafa 14
2527	Garrafa 15
2528	Garrafa 16
2529	Garrafa 17
2530	Garrafa 18
2531	Garrafa 19
2532	Garrafa 20
2533	Garrafa 21
2534	Garrafa 22
2535	Garrafa 23
2536	Garrafa 24
2537	Traseira
2538	Menu diagnósticos
2539	Última mensagem
2540	Volume garrafa esquerda
2541	Volume amostra
2542	Luz de fundo
2543	Ligado
2544	Atraso de alarme
2545	Código extendido original
2546	Nome programa:
2547	TAG do equipamento
2548	Código extendido atual
2549	Device Settings
2550	Reset
2551	Offline
2552	Maintenance
2553	HART information
2554	Long TAG
2555	DD revision
2556	device_icon
2557	Device Variable
2558	8.3f
2559	PV Analog Channel Saturated
2560	PV Analog Channel Fixed
2561	Wireless
2562	WirelessHART Device
2563	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
2564	Primary
2565	Primary Analog Channel
2566	Secondary
2567	Secondary Analog Channel
2568	Tertiary
2569	Tertiary Analog Channel
2570	Quaternary
2571	Quaternary Analog Channel
2572	Quinary
2573	Quinary Analog Channel
2574	Critical Power Failure
2575	Lock all
2576	Trim not supported
2577	Configuration cannot be changed
2578	Locked by gateway
2579	Analog Input Channel
2580	Analog Output Channel
2581	Secondary Analog Channel Saturated
2582	Tertiary Analog Channel Saturated
2583	Quaternary Analog Channel Saturated
2584	Quinary Analog Channel Saturated
2585	Secondary Analog Channel Fixed
2586	Tertiary Analog Channel Fixed
2587	Quaternary Analog Channel Fixed
2588	Quinary Analog Channel Fixed
2589	Simulation active
2590	The device is in simulation mode and the level output is not representative of the process.
2591	Non-Volatile memory failure
2592	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
2593	Volatile memory error
2594	The RAM memory check is invalid or maybe corrupt
2595	Watchdog reset executed
2596	A watchdog reset has been performed
2597	Voltage conditions out of range
2598	A voltage condition is outside its allowable range
2599	Environmental conditions out of range
2600	An internal or environmental condition is beyond acceptable limits.
2601	Electronic failure
2602	A hardware problem not related to the sensor has been detected.
2603	Subdevice list changed
2604	Duplicate master detected
2605	Capacity Denied
2606	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
2607	Bandwidth allocation pending
2608	Block transfer pending
2609	Battery life
2610	Loop current
2611	Primary variable
2612	Secondary variable
2613	Tertiary variable
2614	Quaternary variable
2615	Read receive time
2616	Write date and time
2617	Non-Volatile Clock
2618	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
2619	Clock Uninitialized
2620	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
2621	No restrictions
2622	SI Only
2623	Restricted to SI Unit codes only
2624	Process automation device
2625	Discrete device
2626	Hybrid:Process automation+discrete
2627	I/O System
2628	WirelessHART Process automation device
2629	WirelessHART Discrete device
2630	WirelessHART Process automation+discrete
2631	WirelessHART Gateway
2632	WirelessHART Access point
2633	WirelessHART Process adapter
2634	WirelessHART Discrete adapter
2635	WirelessHART enabled handheld/portable maintenance tool
2636	Device Profile
2637	US
2638	United States of America
2639	JP
2640	Japan
2641	DE
2642	Germany
2643	FR
2644	France
2645	ES
2646	Spain
2647	RU
2648	Russian Federation
2649	CN
2650	People's Republic of China
2651	Secondary Master
2652	Primary Master
2653	Device Diagnostic Status 0
2654	Device Diagnostic Status 1
2655	I/O and Subdevice Status
2656	WirelessHART Status
2657	Time Set Option
2658	Real Time Clock Flags
2659	Country
2660	Country of intended device installation
2661	SI Unit Control
2662	Indicates if device should only display SI unit codes
2663	Time Stamp
2664	Relative time value on network
2665	8u
2666	Dynamic Variables Returned for Device Variables
2667	Configuration Change Counter Mismatch
2668	Status bytes mismatch
Reference ID	String