Device dictionary

Loading…

Reference ID	String
0	Deltabar FMD7x
1	Cust. tag number
2	Status Byte 0
3	No error
4	F261 Electronics
5	F282 Data memory
6	F283 Permanent mem.
7	Status Byte 1
8	F062 Sensor connect
9	F163 Sensor connect
10	Status Byte 2
11	F002 Sens.unknown LP
12	F002 Sens.unknown HP
13	F083 Perm. mem. LP
14	F083 Perm. mem. HP
15	F081 Initialization
16	F162 Sensor connect
17	F164 Sensor sync.
18	Status Byte 3
19	F162 Sensor conn. LP
20	F162 Sensor conn. HP
21	F411 Up-/Download
22	F165 Sensor assignm.
23	F512 Linearization
24	F511 Linearization
25	F510 Linearization
26	F437 Configuration
27	Status Byte 4
28	S140 Work.range P LP
29	S140 Work.range P HP
30	S841 Sensor range LP
31	S841 Sensor range HP
32	S110 Work.range T LP
33	S822 Process temp.LP
34	Status Byte 5
35	S110 Work.range T HP
36	S822 Process temp.HP
37	S945 Press. limit LP
38	C824 Process press.
39	M434 Scaling
40	Status Byte 6
41	S971 Adjustment
42	M431 Adjustment
43	C412 Backup in prog.
44	M283 Permanent mem.
45	M438 Data record
46	M002 Sensor unknown
47	C485 Measure simul.
48	C482 Current simul.
49	Status Byte 7
50	C484 Error simul.
51	not used
52	Square root
53	Level linear
54	Level hor. cyl.
55	Dummy unit
56	None
57	Dummy float
58	.3f
59	Pres Dev fmly
60	Pres Class
61	Pres PDQ
62	Pres LS
63	Pres Fmly stat
64	8.3f
65	7d
66	Pres Lower trim
67	Pres Upper trim
68	Pres Trim support
69	Pres Min lower trim
70	Pres Max lower trim
71	Pres Min upper trim
72	Pres Max upper trim
73	Pres Min trim diff
74	Meas.Diff.Press.
75	Corrected press.
76	Meas. press. HP
77	Sensor press. HP
78	Meas. press. LP
79	Sensor press. LP
80	Sensor temp. HP
81	Sensor temp. LP
82	Electronics temp
83	Level before Lin
84	Tank content
85	Process density
86	Get LRV
87	Sets lower range value / Reference pressure is present at device
88	Abort
89	Confirm
90	Get URV
91	Sets upper range value / Reference pressure is present at device
92	Diagnostic 1
93	Displays current messages according to their priority
94	F140 Work.range P LP
95	F140 Work.range P HP
96	F841 Sensor range LP
97	F841 Sensor range HP
98	F945 Press. limit LP
99	dummy
100	Diagnostic 2
101	Diagnostic 3
102	Diagnostic 4
103	Diagnostic 5
104	Diagnostic 6
105	Diagnostic 7
106	Diagnostic 8
107	Diagnostic 9
108	Diagnostic 10
109	Diagnostic code
110	Displays the current message with the highest priority
111	Instructions
112	Displays the maintenance instructions.
113	No action needed
114	1.Restart 2.Change electronics
115	1.Reset 2.Change electronics
116	1.Check sensorcable 2.Change electronics 3.Contact EH service
117	1.Restart 2.Check sensorcable 3.Contact EH service
118	1.Contact EH service
119	1.Restart 2.Contact EH service
120	1.Reset 2.Chk sensorcable 3.Contact EH service
121	1.Check sensorcable 2.Replace sensor 3.Contact EH service
122	1.Restart 2.Replace sensor 3.Contact EH service
123	1.Retry download 2.Try another file 3.Reset
124	1.Set Transm.connect 2.Restart 3.Contact EH service
125	1.Table not monoton 2.Correct table 3.Activate table
126	1.Table too small 2.Correct table 3.Activate table
127	1.End lin. table edition 2.Select ''Linear''
128	1.Check PV_TYPE 2.Check LIN_TYPE 3.Check PV_UNIT
129	1.Chk process pres. 2.Check sensor range
130	1.Check pressure 2.Contact EH service
131	1.Chk process temp. 2.Check Temp. range
132	1.Check temperature 2.Check sensor range
133	1.Check pressure 2.Change press.limit 3.Contact EH service
134	1.Check pressure 2.Restart 3.Reset
135	1.Chk measure range 2.Check config. 3.Contact EH service
136	1.Check pressure 2.Chk measure range 3.Chk configuration
137	1.Chk measure range 2.Chk pos. offset 3.Chk configuration
138	1.Wait download
139	1.Check config. 2.Restart 3.Change electronics
140	1.End simulation
141	Instructions 1
142	Instructions 2
143	Instructions 3
144	Instructions 4
145	Instructions 5
146	Instructions 6
147	Instructions 7
148	Instructions 8
149	Instructions 9
150	Instructions 10
151	Unit after lin.
152	Selection of the volume unit
153	%
154	cm
155	dm
156	m
157	in
158	ft
159	m³
160	in³
161	ft³
162	l
163	hl
164	kg
165	t
166	lb
167	gal
168	Igal
169	mm
170	Output fail mode
171	Selection of the current value in the event of an alarm
172	Min
173	Max
174	Hold
175	Sim. error no.
176	Enter failure number for simulation
177	5u
178	Format 1st value
179	Specifies the number of decimal places for the value displayed in the main line
180	x
181	x.x
182	x.xx
183	x.xxx
184	x.xxxx
185	x.xxxxx
186	Auto
187	Burst option
188	Specifies which command is sent to the master
189	Command 1
190	Command 2
191	Command 3
192	Command 9
193	Command 33
194	Burst mode
195	Enables and disables the ''Burst mode'' function
196	Off
197	On
198	HART input form.
199	Displays the format of the data incoming via HART protocol
200	HART input stat.
201	Displays the status of the data incoming via HART protocol
202	Bad
203	Uncertain
204	Good
205	HART input unit
206	Displays the unit of the data incoming via HART protocol
207	Unknown
208	mbar
209	bar
210	mmH2O
211	ftH2O
212	inH2O
213	Pa
214	hPa
215	kPa
216	MPa
217	psi
218	mmHg
219	inHg
220	Torr
221	g/cm²
222	kg/cm²
223	lb/ft²
224	atm
225	°C
226	°F
227	K
228	R
229	HART input value
230	Input value for processing two HART variables to one output value
231	.1f
232	.2f
233	.4f
234	.5f
235	Config. counter
236	Displays the configuration counter
237	Sim. current
238	Enter simulation value
239	mA
240	Output current
241	Displays the actual current value
242	Density unit
243	Selection of the density unit / The measured pressure is converted to a height
244	g/cm³
245	kg/m³
246	kg/dm³
247	lb/in³
248	lb/ft³
249	Manufacturer ID
250	Displays the manufacturer number in a decimal numerical format
251	Ext. order code
252	Displays the device designation and the order code
253	________________________________
254	Order code
255	Displays the order code
256	________________________________
257	Device revision
258	Displays the device revision
259	3u
260	Serial number
261	Displays the serial number of the device
262	0000000000000000
263	Status
264	Displays the actual status of the device
265	Good
266	Failure
267	Function check
268	Maintenance req.
269	Out of spec.
270	Device type code
271	Display the device identification number in a decimal numerical format
272	Sim. diff.press.
273	Language
274	Selection of the menu language for the on-site display
275	English
276	Deutsch
277	Français
278	Italiano
279	Español
280	Português
281	Nihon-go (JPN)
282	Hànyu (CHS)
283	Display mode
284	Specifies the contents for the main line of the on-site display in the measuring mode
285	Main value only
286	External value only
287	All alternating
288	2nd disp. value
289	Specifies the contents for the alternating line of the on-site display in the measuring mode
290	None
291	Differential press.
292	Level before lin.
293	Current
294	Measured value(%)
295	3rd disp. value
296	Download select.
297	Select the data records for the upload/download function in Fieldcare and PDM.
298	Configuration copy
299	Device replacement
300	Electronics replace
301	Electr.serial no
302	Displays the serial number of the transmitter electronic.
303	123456
304	ENP version
305	Displays the version of the electronic nameplate
306	2.02.00
307	Set min. current
308	Enter lower current limit / Options: 3.8mA; 4.0mA
309	3.8 mA
310	4.0 mA
311	Device name str.
312
313	HART date
314	Enter the date of the last configuration change
315	__/__/__
316	Descriptor
317	Enter the tag description
318	________________
319	HART message
320	Enter a message
321	________
322	Height unit
323	Selection of height unit / The measured pressure is converted
324	Offset trim 20mA
325	Displays the difference between 20mA and the value entered for the Curr. trim 20mA paramter
326	Curr. trim 20mA
327	Enter current value for the upper point of the current output trim line
328	Full calib.
329	Enter a level, volume, mass or percentage value for the upper calibration point
330	Enter level value for the upper calibration point (tank full)
331	Full pressure
332	Enter the pressure value for the upper calibration point
333	Last diag. code
334	Displays the last message that occured and was eliminated.
335	Last diag. 1
336	Displays the last messages that occured and were eliminated.
337	Last diag. 2
338	Last diag. 3
339	Last diag. 4
340	Last diag. 5
341	Last diag. 6
342	Last diag. 7
343	Last diag. 8
344	Last diag. 9
345	Last diag. 10
346	Full height
347	Enter the height value for the upper calibration point (tank full)
348	Adjust density
349	Enter the density of a fluid / The measured pressure is converted to a height
350	Level selection
351	Selection of the level mode
352	In pressure
353	In height
354	Calibration mode
355	Selection of the calibration mode / Wet or dry calibration
356	Wet
357	Dry
358	Enter a new density value for density correction
359	Empty height
360	Enter the height value for the lower calibration point (tank empty)
361	Sim. level
362	Tank description
363	Enter a tank description for simulation needs
364	Edit table
365	Selection of the function for the linearisation table
366	Current Point
367	Next point
368	Previous point
369	Insert point
370	Delete point
371	Line number
372	Enter the number of the table point.
373	Lin. mode
374	Selection of the entry mode for the linearisation table
375	Linear
376	Erase table
377	Manual entry
378	Semi-auto. entry
379	Activate table
380	X-value
381	X-Value of linenumber / The hydrostatic pressure present is displayed and saved by confirming the Y-value
382	Y-value
383	Y-Value of linenumber / Depending on the settings of the parameter Unit after lin., enter the volume, mass or % value
384	Device tag
385	Enter a tag number
386	Current mode
387	Enables and disables the ''Multidrop mode''
388	Fixed
389	Signaling
390	Offset trim 4mA
391	Displays the difference between 4mA and the value entered for the Curr. trim 4mA parameter
392	Curr. trim 4mA
393	Enter current value for the lower point of the current output trim line
394	Set LRV
395	.7f
396	Empty calib.
397	Enter a level, volume, mass or percentage value for the lower calibration point
398	Enter level value for the lower calibration point (tank empty)
399	Empty pressure
400	Enter the pressure value for the lower calibration point
401	High alarm curr.
402	Enter current value for maximum alarm current.
403	Set URV
404	Enter a level value for the upper current value (20mA).
405	Displays the level value prior to linearisation
406	.0f
407	Displays the level value after linearisation
408	Displays the temperature currently measured in the sensor / The value can deviate from the process temperature
409	Displays the measured temperature of the main electronics
410	Measured value
411	mH2O
412	kgf/cm²
413	Enter a level value for the lower current value (4mA).
414	Minimum span
415	Preamble number
416	Enter the number of preambles in the HART protocol
417	Sensor changes
418	Displays the number of sensor changes accomplished since first commissioning
419	Operating hours
420	Displays the hours of operation / Can't be reseted
421	10u
422	Measuring mode
423	The operating menu is structured according to the selected measuring mode
424	Pressure
425	Level
426	Unit before lin.
427	Selection of the unit for the level parameters and the measured value.
428	Bus address
429	Enter the address for the exchange of data via HART protocol
430	Pressure abs rng
431	Pos. zero adjust
432	Gets the acting differential pressure as offset.
433	Displays the corrected pressure
434	Displays the measured pressure of the sensor before trim.
435	Displays the measured pressure of the sensor after recalibration.
436	Damping value
437	Enter a damping time
438	s
439	Displays the calculated differential pressure after sensor recalibration, position adjustment and damping.
440	High press. side
441	Inverts the assignment of the high and low pressure side
442	Sensor HP
443	Sensor LP
444	Calib. offset
445	Position adjustment / Sets the zero point to zero
446	Lo trim measured
447	Displays the pressure present during the calibration of the device for the lower cal. point
448	Lo trim sensor
449	Sets the acting pressure for the lower calibration point
450	Max. meas.press.
451	Displays the largest measured pressure value / For reset press Reset peakhold.
452	Min. meas.press.
453	Displays the smallest measured pressure value / For reset press Reset peakhold.
454	URL sensor
455	Displays the upper measuring limit of the sensor
456	LRL sensor
457	Displays the lower measuring limit of the sensor
458	Sim. press. HP
459	Press. eng. unit
460	Selection of the pressure unit
461	Hi trim measured
462	Displays the pressure present during the calibration of the device for the upper cal. point
463	Hi trim sensor
464	Sets the acting pressure for the upper calibration point
465	Sim. press. LP
466	Pmax process LP
467	Sets the pressure high alarm of the pressure head monitoring function
468	Pmin process LP
469	Sets the pressure low alarm of the pressure head monitoring function
470	Sets lower range value without reference pressure
471	Sets upper range value without reference pressure
472	Primary value
473	Displays the primary value
474	Primary value is
475	Displays the measured value depending on the measuring mode selected
476	Level before lin
477	Temp. electronics
478	PV unit
479	4th value
480	Displays the fourth process value
481	4th value is
482	Selection of the fourth process value
483	QV unit
484	Counter P > Pmax
485	Displays the number of overshoots of Upper Range Limit
486	Counter P < Pmin
487	Displays the number of undershoots of Lower Range Limit
488	Reset logbook
489	Resets messages of the Last diag. codes.
490	Enter reset code
491	Resets parameters completely or partially to factory values or delivery status
492	Reset peakhold
493	This parameter lists all peak hold indicator parameters that can be reseted. Select the one you want to reset
494	Pressure HP
495	Pressure LP
496	Reset all
497	Secondary value
498	Displays the second process value
499	Secondary val.is
500	Selection of the second process value
501	SV unit
502	Ser.no.sensor LP
503	Displays the serial number of the sensor LP.
504	Sensor meas.type
505	Differential
506	Gauge
507	Absolut
508	multi
509	Ser.no.sensor HP
510	Displays the serial number of the sensor HP.
511	Simulation mode
512	Selection of the simulation type and enables the simulation
513	Flow
514	Alarm/Warning
515	Firmware version
516	Displays the software version
517	12345678
518	Hart version
519	Universal Revision- Revision of the Universal Device Description, that the Field Device conforms to.
520	Startcurrent
521	Selection of the desired start current
522	12mA
523	Max. alarm (110%)
524	Lock state
525	Displays the lock state
526	HW locked
527	Reserved 1
528	SW locked
529	Unlocked
530	Service unlocked
531	Production unlocked
532	Reserved 2
533	SIL locked
534	Reserved 3
535	Reserved 4
536	Reserved 5
537	Reserved 6
538	Upload active
539	Download active
540	Alarm cur.switch
541	Displays the position of the alarm current switch on the main electronics
542	SW setting
543	Alarm min
544	Damping switch
545	Displays the position of the damping switch on the main electronics
546	Lock switch
547	Displays the position of the hw-lock switch on the main electronics
548	Operator code
549	Enter a code to lock or unlock operation menu
550	Sim. tank cont.
551	Max. meas. temp.
552	Displays the highest measured temperature value / For reset press Reset peakhold.
553	Min. meas. temp.
554	Displays the smallest measured temperature value / For reset press Reset peakhold.
555	Tmax sensor
556	Tmin sensor
557	No
558	Yes
559	Temp. eng. unit
560	Selection of the unit for the temperature measured value
561	Third value
562	Displays the third process value
563	Third value is
564	Selection of the third process value
565	TV unit
566	Transm. connect.
567	Specifies the connection of the transmitter to a designated sensor (to HP/to LP).
568	To sensor LP
569	To sensor HP
570	Alarm behav. P
571	Selection of the behavior of the current output when sensor limits undershoot or overshoot
572	Warning
573	Alarm
574	Special
575	Code definition
576	Enter a code definition for unlocking the device
577	Loop Warning Variables
578	Loop Warning Variables- Variables that display a warning message before new values are sent.
579	VARIABLE_ARRAY_INDEX READ
580	Offline
581	Display/Operat.
582	Setup
583	Diagnosis
584	Expert
585	System
586	Measurement
587	Output
588	Communication
589	Instrument info
590	Display
591	Management
592	Basic setup
593	Linearization
594	Sens. limits HP
595	Sens. limits LP
596	Sensor trim HP
597	Sensor trim LP
598	Diagnostic list
599	Event logbook
600	Simulation
601	Current output
602	HART config
603	HART info
604	HART output
605	HART input
606	Measured values
607	Reset
608	Extended setup
609	HART diagnosis
610	Status signal
611	<< Configuration Flag Reset
612	Commands reset the configuration flag.
613	pre_send_configuration_method
614	post_send_configuration_method
615	Device information
616	Device Status
617	Device ICON
618	Configure/Setup
619	Current trim
620	Device Diagnostics
621	Instrument Health Status
622	DeviceInfo
623	SetupLevel
624	ProcessValues
625	SetupPressure
626	Display
627	SetupMode
628	SetupCurrent
629	Diagnostics
630	DisplayLanguage
631	ExtendedSetup
632	Instrument health status
633	Process variables
634	Temperature
635	HP
636	LP
637	Linewriter
638	Meas.Diff.Press / Current output
639	Meas.press HP / Meas.press LP
640	Meas.Diff.Press
641	Level before lin / Meas.Diff.Press
642	Level before lin / Current output
643	Tank content / Current output
644	Sensor temp. HP
645	Sensor temp. LP
646	Field device status
647	HartLogo
648	Linearization table
649	Table graph
650	Table editor
651	Index
652	X-Value
653	Y-Value
654	Linearization
655	X-Value
656	The X axis for Linearization.
657	Y-Value
658	The Y axis for Linearization.
659	variable_array_index_1
660	Y Value 00
661	Number of points
662	Refresh Graph
663	Read table from device
664	Write table to device and activate it
665	X Value 01
666	Y Value 01
667	X Value 02
668	Y Value 02
669	X Value 03
670	Y Value 03
671	X Value 04
672	Y Value 04
673	X Value 05
674	Y Value 05
675	X Value 06
676	Y Value 06
677	X Value 07
678	Y Value 07
679	X Value 08
680	Y Value 08
681	X Value 09
682	Y Value 09
683	X Value 10
684	Y Value 10
685	X Value 11
686	Y Value 11
687	X Value 12
688	Y Value 12
689	X Value 13
690	Y Value 13
691	X Value 14
692	Y Value 14
693	X Value 15
694	Y Value 15
695	X Value 16
696	Y Value 16
697	X Value 17
698	Y Value 17
699	X Value 18
700	Y Value 18
701	X Value 19
702	Y Value 19
703	X Value 20
704	Y Value 20
705	X Value 21
706	Y Value 21
707	X Value 22
708	Y Value 22
709	X Value 23
710	Y Value 23
711	X Value 24
712	Y Value 24
713	X Value 25
714	Y Value 25
715	X Value 26
716	Y Value 26
717	X Value 27
718	Y Value 27
719	X Value 28
720	Y Value 28
721	X Value 29
722	Y Value 29
723	X Value 30
724	Y Value 30
725	X Value 31
726	Y Value 31
727	X Value 32
728	Y Value 32
729	X Value 01
730	Y Value 01
731	X Value 02
732	Y Value 02
733	X Value 03
734	Y Value 03
735	X Value 04
736	Y Value 04
737	X Value 05
738	Y Value 05
739	X Value 06
740	Y Value 06
741	X Value 07
742	Y Value 07
743	X Value 08
744	Y Value 08
745	X Value 09
746	Y Value 09
747	X Value 10
748	Y Value 10
749	X Value 11
750	Y Value 11
751	X Value 12
752	Y Value 12
753	X Value 13
754	Y Value 13
755	X Value 14
756	Y Value 14
757	X Value 15
758	Y Value 15
759	X Value 16
760	Y Value 16
761	X Value 17
762	Y Value 17
763	X Value 18
764	Y Value 18
765	X Value 19
766	Y Value 19
767	X Value 20
768	Y Value 20
769	X Value 21
770	Y Value 21
771	X Value 22
772	Y Value 22
773	X Value 23
774	Y Value 23
775	X Value 24
776	Y Value 24
777	X Value 25
778	Y Value 25
779	X Value 26
780	Y Value 26
781	X Value 27
782	Y Value 27
783	X Value 28
784	Y Value 28
785	X Value 29
786	Y Value 29
787	X Value 30
788	Y Value 30
789	X Value 31
790	Y Value 31
791	X Value 32
792	Y Value 32
793	Tansmitter spec command error
794	Set to nearest possible value
795	Invalid value selection
796	Lower range value too small
797	Upper range value too high
798	Upper and Lower range value out of range
799	Span too small
800	Invalid span
801	Upload variables
802	PV Analog Channel Saturated
803	PV Analog Channel Fixed
804	Enable on token-passing data link layer only
805	Enable on TDMA data link layer only
806	Enable on both TDMA and token-passing data link layer
807	Wireless
808	WirelessHART Device
809	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
810	Primary
811	Primary Analog Channel
812	Secondary
813	Secondary Analog Channel
814	Tertiary
815	Tertiary Analog Channel
816	Quaternary
817	Quaternary Analog Channel
818	Quinary
819	Quinary Analog Channel
820	Critical Power Failure
821	Lock all
822	Trim not supported
823	Configuration cannot be changed
824	Locked by gateway
825	Analog Input Channel
826	Analog Output Channel
827	Secondary Analog Channel Saturated
828	Tertiary Analog Channel Saturated
829	Quaternary Analog Channel Saturated
830	Quinary Analog Channel Saturated
831	Secondary Analog Channel Fixed
832	Tertiary Analog Channel Fixed
833	Quaternary Analog Channel Fixed
834	Quinary Analog Channel Fixed
835	8u
836	count
837	Device Variable
838	Variable to trim
839	Good No error Remedy: No action needed
840	Failure # 261: Electronics Cause: - Main electronics defective. - Fault in the main electronics. Remedy: 1.Restart 2.Change electronics
841	Failure # 282: Data memory Cause: - Fault in the main electronics. - Main electronics defective. Remedy: 1.Restart 2.Change electronics
842	Failure # 283: Permanent mem. Cause: - Main electronics defective. - Electromagnetic effects are greater than specified in the technical data. - The supply voltage is disconnected when writing. - An error occurred when writing. Remedy: 1.Reset 2.Change electronics
843	Failure # 062: Sensor connect Cause: - Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. - Cable connection between the sensor and main electronics is disconnected. - Sensor defective. Remedy: 1.Check sensorcable 2.Change electronics 3.Contact EH service
844	Failure # 163: Sensor connect Cause: - Cable connection between the sensors HP and LP is disconnected. - Sensor defective (slave). - Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. Remedy: 1.Restart 2.Check sensorcable 3.Contact EH service
845	Failure # 002: Sens.unknown LP Cause: - Sensor does not suit the device (electronic sensor nameplate). Remedy: 1.Contact EH service
846	Failure # 002: Sens.unknown HP Cause: - Sensor does not suit the device (electronic sensor nameplate). Remedy: 1.Contact EH service
847	Failure # 083: Perm. mem. LP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective. Remedy: 1.Restart 2.Contact EH service
848	Failure # 083: Perm. mem. HP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective. Remedy: 1.Restart 2.Contact EH service
849	Failure # 081: Initialization Cause: - Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. - Cable connection between the sensor and main electronics is disconnected. - Sensor defective. Remedy: 1.Reset 2.Chk sensorcable 3.Contact EH service
850	Failure # 162: Sensor connect Cause: - Sensor defective (master). - Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. Remedy: 1.Check sensorcable 2.Replace sensor 3.Contact EH service
851	Failure # 164: Sensor sync. Cause: - The sensors cannot be synchronized, the measurement is not accurate. - Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. - Sensor(s) defective. Remedy: 1.Restart 2.Replace sensor 3.Contact EH service
852	Failure # 162: Sensor conn. LP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective. Remedy: 1.Check sensorcable 2.Replace sensor 3.Contact EH service
853	Failure # 162: Sensor conn. HP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective. Remedy: 1.Check sensorcable 2.Replace sensor 3.Contact EH service
854	Failure # 411: Up-/Download Cause: - The file is defective. - During the download, the data are not correctly transmitted to the processor, e.g. due to open cable connections, spikes (ripple) on the supply voltage or electromagnetic effects. Remedy: 1.Retry download 2.Try another file 3.Reset
855	Failure # 165: Sensor assignm. Cause: - The transmitter isn't assigned to the sensors HP or LP. Remedy: 1.Set Transm.connect 2.Restart 3.Contact EH service
856	Failure # 512: Linearization Cause: - The linearization table is not monotonic increasing or decreasing. Remedy: 1.Table not monoton 2.Correct table 3.Activate table
857	Failure # 511: Linearization Cause: - The linearization table consists of less than 2 points. Remedy: 1.Table too small 2.Correct table 3.Activate table
858	Failure # 510: Linearization Cause: - The linearization table is being edited. Remedy: 1.End lin. table edition 2.Select ''Linear''
859	Failure # 437: Configuration Cause: - The executed configuration is inconsistent. - The executed download is inapropriate Remedy: 1.Check PV_TYPE 2.Check LIN_TYPE 3.Check PV_UNIT
860	Out of spec. # 140: Work.range P LP Cause: - Overpressure and low pressure present. - Electromagnetic effects are greater than specified in the technical data. - Sensor defective. Remedy: 1.Chk process pres. 2.Check sensor range
861	Failure # 140: Work.range P LP Cause: - Overpressure and low pressure present. - Electromagnetic effects are greater than specified in the technical data. - Sensor defective. Remedy: 1.Chk process pres. 2.Check sensor range
862	Out of spec. # 140: Work.range P HP Cause: - Overpressure and low pressure present. - Electromagnetic effects are greater than specified in the technical data. - Sensor defective. Remedy: 1.Chk process pres. 2.Check sensor range
863	Failure # 140: Work.range P HP Cause: - Overpressure and low pressure present. - Electromagnetic effects are greater than specified in the technical data. - Sensor defective. Remedy: 1.Chk process pres. 2.Check sensor range
864	Out of spec. # 841: Sensor range LP Cause: - Overpressure or low pressure present. - Sensor defective. Remedy: 1.Check pressure 2.Contact EH service
865	Failure # 841: Sensor range LP Cause: - Overpressure or low pressure present. - Sensor defective. Remedy: 1.Check pressure 2.Contact EH service
866	Out of spec. # 841: Sensor range HP Cause: - Overpressure or low pressure present. - Sensor defective. Remedy: 1.Check pressure 2.Contact EH service
867	Failure # 841: Sensor range HP Cause: - Overpressure or low pressure present. - Sensor defective. Remedy: 1.Check pressure 2.Contact EH service
868	Out of spec. # 110: Work.range T LP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective Remedy: 1.Chk process temp. 2.Check Temp. range
869	Out of spec. # 822: Process temp.LP Cause: - The temperature measured in the sensor is higher than the upper nominal temperature of the sensor. - The temperature measured in the sensor is lower than the lower nominal temperature of the sensor. Remedy: 1.Check temperature 2.Check sensor range
870	Out of spec. # 110: Work.range T HP Cause: – Electromagnetic effects are greater than specified in the technical data. This message normally only appears briefly. – Sensor defective Remedy: 1.Chk process temp. 2.Check Temp. range
871	Out of spec. # 822: Process temp.HP Cause: - The temperature measured in the sensor is higher than the upper nominal temperature of the sensor. - The temperature measured in the sensor is lower than the lower nominal temperature of the sensor. Remedy: 1.Check temperature 2.Check sensor range
872	Out of spec. # 945: Press. limit LP Cause: - The set pressure high limit or low limit of the sensor LP is exceeded. - Sensor LP defective. Remedy: 1.Check pressure 2.Change press.limit 3.Contact EH service
873	Failure # 945: Press. limit LP Cause: - The set pressure high limit or low limit of the sensor LP is exceeded. - Sensor LP defective. Remedy: 1.Check pressure 2.Change press.limit 3.Contact EH service
874	Function check # 824: Process press. Cause: - Electromagnetic effects are greater than specified in the technical data. - Overpressure or low pressure present. - This message normally only appears briefly. Remedy: 1.Check pressure 2.Restart 3.Reset
875	Maintenance req. # 434: Scaling Cause: – Values for calibration (e.g. lower-range value and upper-range value) are too close together. – The lower-range value and/or upperrange value undershoot or exceed the sensor range limits. Remedy: 1.Chk measure range 2.Check config. 3.Contact EH service
876	Out of spec. # 971: Adjustment Cause: -The current is outside the permitted range of 3.8 to 20.5 mA. -The pressure present is outside the set measuring range (but might be within the sensor range). -The adjustment performed would cause the sensor nominal range to be undershot or overshot. Remedy: 1.Check pressure 2.Chk measure range 3.Chk configuration
877	Maintenance req. # 431: Adjustment Cause: -The current is outside the permitted range of 3.8 to 20.5 mA. -The pressure present is outside the set measuring range (but might be within the sensor range). -The adjustment performed would cause the sensor nominal range to be undershot or overshot. Remedy: 1.Chk measure range 2.Chk pos. offset 3.Chk configuration
878	Function check # 412: Backup in prog. Cause: - Downloading. Remedy: 1.Wait download
879	Maintenance req. # 283: Permanent mem. Cause: – Cause as indicated for F283. – Correct measurement can continue as long as you do not need the peakhold indicator function. Remedy: 1.Reset 2.Change electronics
880	Maintenance req. # 438: Data record Cause: - The supply voltage is disconnected when writing. - An error occured when writing. Remedy: 1.Check config. 2.Restart 3.Change electronics
881	Maintenance req. # 002: Sensor unknown Cause: - Sensor does not suit the device (electronic sensor nameplate). Remedy: 1.Contact EH service
882	Function check # 485: Measure simul. Cause: – Simulation is switched on, i.e. the device is not measuring at present. Remedy: 1.End simulation
883	Function check # 482: Current simul. Cause: – Current simulation is switched on, i.e. the device is not measuring at present. Remedy: 1.End simulation
884	Function check # 484: Error simul. Cause: - Fault state sim. is switched on, i.e. the device is not measuring at present Remedy: 1.End simulation
885	No action needed
886	1.Restart 2.Change electronics
887	1.Reset 2.Change electronics
888	1.Check sensorcable 2.Change electronics 3.Contact EH service
889	1.Restart 2.Check sensorcable 3.Contact EH service
890	1.Contact EH service
891	1.Restart 2.Contact EH service
892	1.Reset 2.Chk sensorcable 3.Contact EH service
893	1.Check sensorcable 2.Replace sensor 3.Contact EH service
894	1.Restart 2.Replace sensor 3.Contact EH service
895	1.Retry download 2.Try another file 3.Reset
896	1.Set Transm.connect 2.Restart 3.Contact EH service
897	1.Table not monoton 2.Correct table 3.Activate table
898	1.Table too small 2.Correct table 3.Activate table
899	1.End lin. table edition 2.Select ''Linear''
900	1.Check PV_TYPE 2.Check LIN_TYPE 3.Check PV_UNIT
901	1.Chk process pres. 2.Check sensor range
902	1.Check pressure 2.Contact EH service
903	1.Chk process temp. 2.Check Temp. range
904	1.Check temperature 2.Check sensor range
905	1.Check pressure 2.Change press.limit 3.Contact EH service
906	1.Check pressure 2.Restart 3.Reset
907	1.Chk measure range 2.Check config. 3.Contact EH service
908	1.Check pressure 2.Chk measure range 3.Chk configuration
909	1.Chk measure range 2.Chk pos. offset 3.Chk configuration
910	1.Check config. 2.Restart 3.Change electronics
911	Current Point;Next point;Previous point;Insert point;Delete point
912	Current Point;Next point;Previous point
913	HW Lock state is ON. Check Dip switch!
914	Software Lock active!
915	Execute Configuration Flag Reset?
916	Get LRV was not done
917	Apply low pressure
918	Get LRV Meas.Diff.Press.: >%{0} %{1}
919	Abort;Confirm
920	Measuring mode 'Pressure' necessary!
921	Get URV was not done
922	Apply high pressure
923	Get URV Meas.Diff.Press.: %{0} %{1}
924	Pos. zero adjust was not done
925	Pos. zero adjust Meas.Diff.Press.: %{0} %{1}
926	Trim was not done
927	Device is locked, please switch off the hardware lock. Select OK when the device is unlocked.
928	Enter the SERVICE-code to unlock the method.
929	iSWLock
930	Wrong SERVICE-code!
931	Press OK when pressure is stable
932	Enter applied pressure value Sensor press. HP: %{0} %{1}
933	trim_point
934	Remove pressure
935	Software Lock active!
936	Service unlock necessary!
937	Enter applied pressure value Sensor press. LP: %{0} %{1}
938	Reset was not done
939	Enter reset code
940	NOTICE - After Reset you have to reconnect the device to the HART - otherwise there might be inconsistence.
941	Reset in progress ! - please wait -
942	Wrong Reset Code !
943	Reset logbook was not done
944	Execute Reset logbook?
945	Reset peakhold was not done
946	Execute Reset peakhold?
947	Abort;Pressure HP;Pressure LP;Sensor temp. HP;Sensor temp. LP;Reset all
948	Read table from device Reading table. Please wait.
949	Note: While writing table device will change to error state! Execute write table to device?
950	Writing table. After clicking. Please wait. Write table to device and activate it.
951	Linearisation table not valid
952	Writing table to device was not done
Reference ID	String