| 0 |
CerabarS |
| 1 |
Endress+Hauser |
| 2 |
________________ |
| 3 |
________________________________ |
| 4 |
________ |
| 5 |
B>ROM failure in Transmitter electronic A113 |
| 6 |
B>RAM error A728 |
| 7 |
B>RAM error A729 |
| 8 |
B>RAM error A736 |
| 9 |
B>Checksum Error in factory segment of EEPROM A121 |
| 10 |
B>Checksum error in EEPROM:configuration segment A110 |
| 11 |
B>Checksum Error in Totalizer EEPROM A132 |
| 12 |
B>Checksum Error in History EEPROM A133 |
| 13 |
B>Checksum error in EEPROM: minMAX segment A131 |
| 14 |
B>EEPROM is defect A130 |
| 15 |
B>Main electronic PCB error A744 |
| 16 |
B>Measurement error A704 |
| 17 |
B>Sensor not connected! A122 |
| 18 |
B>Electronic PCB error during initialisation A743 |
| 19 |
B>Memory failure in signal processor A748 |
| 20 |
B>Sensor-Software not compatible to electronics A747 |
| 21 |
B>Sensor electronic EEPROM error A101 |
| 22 |
B>Sensor connection error (upload) A742 |
| 23 |
B>Measurement error A738 |
| 24 |
B>Measurement error A737 |
| 25 |
B>Measurement error A705 |
| 26 |
B>Measurement error A703 |
| 27 |
B>Measurement error A739 |
| 28 |
B>Sensor diaphragm broken E716 |
| 29 |
B>Sensor connection error cycle disturbed A725 |
| 30 |
C>Sensor connection error - initialising W746 |
| 31 |
C>Calculation Overflow, bad configuration E740 |
| 32 |
C>Sensor pressure error - overrange E727 |
| 33 |
C>Sensor overpressure E115 |
| 34 |
C>Sensor low pressure E120 |
| 35 |
C>Sensor temperature error - overrange E726 |
| 36 |
C>Sensor Over- temperature E715 |
| 37 |
C>Sensor under temperature E720 |
| 38 |
C>Transmitter over temperature E717 |
| 39 |
C>Transmitter under temperature E718 |
| 40 |
C>download error repeat download W116 |
| 41 |
B>LRV or URV out of edit limits A711 |
| 42 |
B>X-VAL of lin. table out of edit limits A707 |
| 43 |
B>100% POINT level out of edit limits A713 |
| 44 |
B>Y-VAL of lin. table out of edit limits A719 |
| 45 |
B>ZERO POSITION level out of edit limits A721 |
| 46 |
B>EMPTY CALIB. or FULL CALIB. out of edit limits A722 |
| 47 |
B>MAX. FLOW out of edit limits A723 |
| 48 |
B>TANK HEIGHT out of edit limits A741 |
| 49 |
C>URV user limits exceeded E731 |
| 50 |
C>LRV user limits exceeded E730 |
| 51 |
C>URV-Temp. User limits exceeded E733 |
| 52 |
C>LRV-Temp. User limits exceeded E732 |
| 53 |
C>Current output out of range E620 |
| 54 |
C>Measuring chain config. exceeds sensor range W701 |
| 55 |
C>Set span too small Not allowed. W710 |
| 56 |
C>Downloading - please wait W106 |
| 57 |
C>Checksum error in EEPROM: peakhold segment W102 |
| 58 |
C>Last Configuration not stored W700 |
| 59 |
C>HistoROM data not consistent W702 |
| 60 |
C>Sensor data unknown W745 |
| 61 |
C>Linearizations curve not monoton W602 |
| 62 |
C>Linearization : less than 2points or points too close W604 |
| 63 |
C>Configuration in HistoROM and device not identical W706 |
| 64 |
I>Simulation is active! W613 |
| 65 |
|
| 66 |
.3f |
| 67 |
Dummy unit |
| 68 |
None |
| 69 |
Pres Dev fmly |
| 70 |
Pres Class |
| 71 |
Pres PDQ |
| 72 |
Pres LS |
| 73 |
Pres Fmly stat |
| 74 |
8.3f |
| 75 |
7d |
| 76 |
Pres Lower trim |
| 77 |
Pres Upper trim |
| 78 |
Pres Trim support |
| 79 |
Pres Min lower trim |
| 80 |
Pres Max lower trim |
| 81 |
Pres Min upper trim |
| 82 |
Pres Max upper trim |
| 83 |
Pres Min trim diff |
| 84 |
Simulate |
| 85 |
|
| 86 |
PRESSURE |
| 87 |
units |
| 88 |
CORRECTED PRESS. |
| 89 |
SENSOR PRESSURE |
| 90 |
SENSOR TEMP. |
| 91 |
PCB TEMPERATURE |
| 92 |
LEVEL BEFORE LIN |
| 93 |
TANK CONTENT |
| 94 |
PRIMARY VALUE |
| 95 |
SECONDARY VALUE |
| 96 |
THIRD VALUE |
| 97 |
4TH VALUE |
| 98 |
PRESSURE |
| 99 |
CORRECTED PRESS. |
| 100 |
PCB TEMPERATURE |
| 101 |
LEVEL BEFORE LIN |
| 102 |
TANK CONTENT |
| 103 |
VARIABLE_ARRAY_INDEX_1 |
| 104 |
VARIABLE_ARRAY_INDEX_2 |
| 105 |
STATUS LOCKING |
| 106 |
Switch locked |
| 107 |
Reserved 1 |
| 108 |
SW Locked |
| 109 |
Unlocked |
| 110 |
Service Unlocked |
| 111 |
Production Unlocked |
| 112 |
Reserved 2 |
| 113 |
SIL Locked |
| 114 |
Reserved 3 |
| 115 |
Reserved 4 |
| 116 |
Reserved 5 |
| 117 |
Reserved 6 |
| 118 |
Upload Active |
| 119 |
Download Active |
| 120 |
CUST.UNIT FACT.V |
| 121 |
.6f |
| 122 |
CUSTOMER UNIT V |
| 123 |
TOTAL.2 OVERFLOW |
| 124 |
LINE-NUMB: |
| 125 |
3u |
| 126 |
X-VAL: |
| 127 |
Y-VAL: |
| 128 |
CUST.UNIT FACT.M |
| 129 |
.0f |
| 130 |
.1f |
| 131 |
.2f |
| 132 |
.4f |
| 133 |
.5f |
| 134 |
.7f |
| 135 |
EMPTY PRESSURE |
| 136 |
EMPTY CALIB. |
| 137 |
FULL CALIB. |
| 138 |
ADJUST DENSITY |
| 139 |
FULL PRESSURE |
| 140 |
UNIT VOLUME |
| 141 |
User unit |
| 142 |
l |
| 143 |
hl |
| 144 |
cm³ |
| 145 |
dm³ |
| 146 |
m³ |
| 147 |
m³E³ |
| 148 |
ft³ |
| 149 |
ft³E³ |
| 150 |
gal |
| 151 |
Igal |
| 152 |
bbl |
| 153 |
ACTIV LIN.TAB.X |
| 154 |
LEVEL MAX |
| 155 |
ACTIV LIN.TAB.Y |
| 156 |
PROCESS DENSITY |
| 157 |
DENSITY UNIT |
| 158 |
g/cm³ |
| 159 |
kg/m³ |
| 160 |
kg/dm³ |
| 161 |
US lb/in³ |
| 162 |
US lb/ft³ |
| 163 |
100% POINT |
| 164 |
ZERO POSITION |
| 165 |
CALIBRATION MODE |
| 166 |
Wet |
| 167 |
Dry |
| 168 |
HYDR. PRESS MIN. |
| 169 |
HYDR. PRESS MAX. |
| 170 |
TANK CONTENT MIN |
| 171 |
LEVEL MIN |
| 172 |
SIM. TANK CONT. |
| 173 |
LIN. EDIT MODE |
| 174 |
Manual |
| 175 |
Semiautomatic |
| 176 |
X-VAL: |
| 177 |
CUSTOMER UNIT M |
| 178 |
TANK DESCRIPTION |
| 179 |
TANK CONTENT MAX |
| 180 |
SIM. LEVEL |
| 181 |
MEASURING TABLE |
| 182 |
Next Point |
| 183 |
Last Input Point |
| 184 |
Abort |
| 185 |
LEVEL MODE |
| 186 |
Linear |
| 187 |
Pressure Linearized |
| 188 |
Height Linearized |
| 189 |
HEIGHT UNIT |
| 190 |
mm |
| 191 |
cm |
| 192 |
dm |
| 193 |
m |
| 194 |
ft |
| 195 |
inch |
| 196 |
MASS UNIT |
| 197 |
g |
| 198 |
kg |
| 199 |
t |
| 200 |
oz |
| 201 |
lb |
| 202 |
ton |
| 203 |
CUST.UNIT FACT.H |
| 204 |
CUSTOMER UNIT H |
| 205 |
LIN. MEASURAND |
| 206 |
Height |
| 207 |
Volume |
| 208 |
Mass |
| 209 |
% (Height) |
| 210 |
LINd. MEASURAND |
| 211 |
Pressure and Volume |
| 212 |
Pressure and Mass |
| 213 |
Pressure and % |
| 214 |
COMB.MEASURAND |
| 215 |
Height and Volume |
| 216 |
Height and Mass |
| 217 |
Height and % |
| 218 |
% Height and Volume |
| 219 |
% Height and Mass |
| 220 |
% Height and % |
| 221 |
TABLE SELECTION |
| 222 |
View meas.Table |
| 223 |
Editor Table |
| 224 |
EDITOR TABLE |
| 225 |
Continue edit |
| 226 |
New Table |
| 227 |
Edit measure table |
| 228 |
ACC. OF GRAVITY |
| 229 |
m/s² |
| 230 |
DAMPING VALUE |
| 231 |
s |
| 232 |
LOW SENSOR TRIM |
| 233 |
LO TRIM MEASURED |
| 234 |
HIGH SENSOR TRIM |
| 235 |
HI TRIM MEASURED |
| 236 |
CALIB. OFFSET |
| 237 |
POS. INPUT VALUE |
| 238 |
PminALARM WINDOW |
| 239 |
PmaxALARM WINDOW |
| 240 |
SIM. PRESSURE |
| 241 |
PRESS. ENG. UNIT |
| 242 |
mbar |
| 243 |
bar |
| 244 |
mmH2O |
| 245 |
mH2O |
| 246 |
ftH2O |
| 247 |
inH2O |
| 248 |
Pa |
| 249 |
hPa |
| 250 |
kPa |
| 251 |
MPa |
| 252 |
psi |
| 253 |
mmHg |
| 254 |
inHg |
| 255 |
Torr |
| 256 |
g/cm² |
| 257 |
kg/cm² |
| 258 |
lb/ft² |
| 259 |
atm |
| 260 |
gf/cm² |
| 261 |
kgf/cm² |
| 262 |
CUSTOMER UNIT P |
| 263 |
CUST.UNIT FACT.P |
| 264 |
POS.ZERO ADJUST |
| 265 |
Confirm |
| 266 |
TminALARM WINDOW |
| 267 |
TmaxALARM WINDOW |
| 268 |
TEMP. ENG. UNIT |
| 269 |
°C |
| 270 |
°F |
| 271 |
K |
| 272 |
R |
| 273 |
LANGUAGE |
| 274 |
English |
| 275 |
Deutsch |
| 276 |
Français |
| 277 |
Italiano |
| 278 |
Español |
| 279 |
Russian |
| 280 |
Japanese(JPN) |
| 281 |
Chinese(CHS) |
| 282 |
DISPLAY CONTRAST |
| 283 |
ALTERNATE DATA |
| 284 |
Off |
| 285 |
On |
| 286 |
MAIN LINE CONT. |
| 287 |
Measured value(PV) |
| 288 |
Measured Value(%) |
| 289 |
Pressure |
| 290 |
Flow |
| 291 |
Level |
| 292 |
Tank content |
| 293 |
Current |
| 294 |
Temperature |
| 295 |
Error Number |
| 296 |
Totaliser 1 |
| 297 |
Totaliser 2 |
| 298 |
MAIN LINE FORMAT |
| 299 |
x |
| 300 |
x.x |
| 301 |
x.xx |
| 302 |
x.xxx |
| 303 |
x.xxxx |
| 304 |
x.xxxxx |
| 305 |
MAIN DATA FORMAT |
| 306 |
Auto |
| 307 |
HistoROM CONTROL |
| 308 |
HistoROM->Device |
| 309 |
Device->HistoROM |
| 310 |
SAFETY LOCK |
| 311 |
Lock |
| 312 |
Unlock |
| 313 |
SAFETY PASSWORD |
| 314 |
5u |
| 315 |
DIGITS SET |
| 316 |
CONFIRM |
| 317 |
Invalid |
| 318 |
Valid |
| 319 |
CONF. PASSWORD |
| 320 |
SAFETY LOCKSTATE |
| 321 |
Locked |
| 322 |
CURRENT OUTPUT |
| 323 |
LinMaxNorm22/3.8/0s |
| 324 |
DOWNLOAD SELECT. |
| 325 |
Configuration copy |
| 326 |
Device replacement |
| 327 |
Electronics replace |
| 328 |
SET MAX. ALARM |
| 329 |
mA |
| 330 |
OUTPUT FAIL MODE |
| 331 |
Min. Alarm(-10%) |
| 332 |
Max. Alarm (110%) |
| 333 |
Hold meas. Value |
| 334 |
SET MIN. CURRENT |
| 335 |
3.8 .. 20.5 mA |
| 336 |
4.0 .. 20.5 mA |
| 337 |
OUTPUT CURRENT |
| 338 |
SIM. CURRENT |
| 339 |
CURR. TRIM 4mA |
| 340 |
CURR. TRIM 20mA |
| 341 |
PREAMBLE NUMBER |
| 342 |
BURST MODE |
| 343 |
BURST OPTION |
| 344 |
SET LRV |
| 345 |
SET URV |
| 346 |
BUS ADDRESS |
| 347 |
HART MESSAGE |
| 348 |
ADDITIONAL INFO. |
| 349 |
MINIMUM SPAN |
| 350 |
ALT.CURR.OUTPUT |
| 351 |
Special |
| 352 |
Normal/NE43 |
| 353 |
OFFSET 4mA TRIM |
| 354 |
OFFSET 20mA TRIM |
| 355 |
SET LRV |
| 356 |
SET URV |
| 357 |
ASSIGN CURRENT |
| 358 |
SET LRV |
| 359 |
SET URV |
| 360 |
CURR. CHARACT. |
| 361 |
Linear |
| 362 |
Bi-linear |
| 363 |
Linear inverse |
| 364 |
Bi-linear invers |
| 365 |
CONFIG RECORDER |
| 366 |
GET LRV |
| 367 |
GET URV |
| 368 |
MAX. TURNDOWN |
| 369 |
DEVICE REVISION |
| 370 |
OPERATING HOURS |
| 371 |
10u |
| 372 |
MEASURING MODE |
| 373 |
ALARM STATUS |
| 374 |
LAST DIAG. CODE |
| 375 |
SIMULATION MODE |
| 376 |
None |
| 377 |
Alarm/Warning |
| 378 |
SIM. ERROR NO. |
| 379 |
ACK. ALARM MODE |
| 380 |
ACK. ALARM |
| 381 |
ALARM DELAY |
| 382 |
ALARM DISPL.TIME |
| 383 |
INSERT PIN No |
| 384 |
ENTER RESET CODE |
| 385 |
WRITE LOCK |
| 386 |
SOFTWARE VERSION |
| 387 |
02.20.00 |
| 388 |
HARDWARE REV. |
| 389 |
02.00.00 |
| 390 |
MANUFACTOR ID |
| 391 |
ELECTR.SERIAL No |
| 392 |
SELECT ALARMTYPE |
| 393 |
Alarm |
| 394 |
Warning |
| 395 |
ERROR No. |
| 396 |
FLEXIBLE ALARMS |
| 397 |
E727 Sensor pressure error - overrange |
| 398 |
E115 Sensor overpressure |
| 399 |
E120 Sensor low pressure |
| 400 |
E620 Current output out of range |
| 401 |
E726 Sensor temperature error - overrange |
| 402 |
E715 Sensor Over- temperature |
| 403 |
E720 Sensor under temperature |
| 404 |
E717 Transmitter over temperature |
| 405 |
E718 Transmitter under temperature |
| 406 |
E731 URV user limits exceeded |
| 407 |
E730 LRV user limits exceeded |
| 408 |
E733 URV-Temp. User limits exceeded |
| 409 |
E732 LRV-Temp. User limits exceeded |
| 410 |
E740 Calculation Overflow, bad configuration |
| 411 |
E716 Sensor diaphragm broken |
| 412 |
reserved |
| 413 |
E727 Sen overrange |
| 414 |
Warning |
| 415 |
Alarm |
| 416 |
E115 Sen overpress |
| 417 |
E120 Sen low press |
| 418 |
E620 Current output |
| 419 |
E726 Sen temp range |
| 420 |
E715 Sen overtemp |
| 421 |
E720 Sen undertemp |
| 422 |
E717 PCB overtemp |
| 423 |
E718 PCB undertemp |
| 424 |
E731 URV user lim. |
| 425 |
E730 LRV user lim. |
| 426 |
E733 URV-Temp.lim. |
| 427 |
E732 LRV-Temp.lim. |
| 428 |
E740 Cal. Overflow |
| 429 |
E716 Diaphr. broken |
| 430 |
RESET ALL ALARMS |
| 431 |
HIST.SAVING CYCL |
| 432 |
*20s |
| 433 |
TABLE ACTIVATE |
| 434 |
No |
| 435 |
Yes |
| 436 |
TABLE EDITOR |
| 437 |
Accept input table |
| 438 |
Insert Point |
| 439 |
Delete Point |
| 440 |
HistoROM AVAIL. |
| 441 |
SEAL TYPE |
| 442 |
Not used |
| 443 |
Unknown |
| 444 |
FKM Viton |
| 445 |
NBR |
| 446 |
EPDM |
| 447 |
Urethane |
| 448 |
IIR |
| 449 |
Kalrez |
| 450 |
FKM Viton Oxyg |
| 451 |
CR |
| 452 |
MVQ |
| 453 |
PTFE Glass |
| 454 |
PTFE Graphite |
| 455 |
PTFE Oxygen |
| 456 |
Copper |
| 457 |
Copper f. Oxygen |
| 458 |
PROC.CONN.TYPE |
| 459 |
Oval Flange |
| 460 |
Thread female |
| 461 |
Thread male |
| 462 |
Flange |
| 463 |
Remote Seal |
| 464 |
MAT.PROC.CONN. + |
| 465 |
Carbon steel |
| 466 |
304 St. St. |
| 467 |
316 St. St. |
| 468 |
Alloy C |
| 469 |
Monel |
| 470 |
Tantalum |
| 471 |
Titanium |
| 472 |
PTFE |
| 473 |
316L |
| 474 |
PVC |
| 475 |
Inconel |
| 476 |
ECTFE |
| 477 |
PVDF |
| 478 |
Pmax PROC. CONN. |
| 479 |
BOLTS MATERIAL |
| 480 |
A2 70 St. St. |
| 481 |
NUTS MATERIAL |
| 482 |
DRAIN VENT MAT. |
| 483 |
DRAIN VENT POS. |
| 484 |
Standard |
| 485 |
Side |
| 486 |
THREAD PROCESS |
| 487 |
1/4-18NPT |
| 488 |
RC1/4 |
| 489 |
G1/2A |
| 490 |
G1A |
| 491 |
G1 1/2A |
| 492 |
1/2MNPT 1/4FNPT |
| 493 |
1/2MNPT |
| 494 |
MOUNTING THREAD |
| 495 |
M10 |
| 496 |
M12 |
| 497 |
7/16UNF |
| 498 |
NR OF CHEM SEAL |
| 499 |
One |
| 500 |
Two |
| 501 |
REMOTE SEAL + |
| 502 |
ISO228 G1/2A |
| 503 |
ISO0228 G1A |
| 504 |
ISO0228 G1 1/2A |
| 505 |
ISO0228 G2A |
| 506 |
ANSI 1''MNPT |
| 507 |
ANSI 1 1/2''MNPT |
| 508 |
ANSI 2''MNPT |
| 509 |
DN25 PN10-40 B1 |
| 510 |
DN25 PN64-160 E |
| 511 |
DN25 PN250 E |
| 512 |
DN25 PN400 E |
| 513 |
DN32 PN25/40 B1 |
| 514 |
DN40 PN25/40 B1 |
| 515 |
DN50 PN10/40 B1 |
| 516 |
DN50 PN25/40 A |
| 517 |
DN50 PN64 B1 |
| 518 |
DN50 PN100/160 E |
| 519 |
DN50 PN250 E |
| 520 |
DN50 PN400 E |
| 521 |
DN80 PN25/40 A |
| 522 |
DN80 PN10/40 B1 |
| 523 |
DN80 PN100 B1 |
| 524 |
DN100 PN10/16 A |
| 525 |
DN100 PN25/40 A |
| 526 |
DN100 PN25/40 B1 |
| 527 |
DN100 PN100 B1 |
| 528 |
1'' 150LBS RF |
| 529 |
1'' 300LBS RF |
| 530 |
1'' 400/600 LBS RF |
| 531 |
1'' 900/1500 LBS RF |
| 532 |
1'' 2500LBS RF |
| 533 |
1 1/2'' 150LBS RF |
| 534 |
1 1/2'' 300LBS RF |
| 535 |
2'' 150LBS RF |
| 536 |
2'' 300LBS RF |
| 537 |
2'' 400/600LBS RF |
| 538 |
2'' 900/1500 LBS RF |
| 539 |
2'' 2500 LBS RF |
| 540 |
3'' 150LBS RF |
| 541 |
3'' 300LBS RF |
| 542 |
4'' 150LBS RF |
| 543 |
4'' 300LBS RF |
| 544 |
10K 50A RF |
| 545 |
10K 80A RF |
| 546 |
10K 100A RF |
| 547 |
Separ G1/2A PN40 |
| 548 |
Separ G1/2A PN160 |
| 549 |
Separ 1/2MNPT PN40 |
| 550 |
Separ 1/2MNPT PN160 |
| 551 |
Separ G1/2B PN40 |
| 552 |
Separ 1/2FNPT PN40 |
| 553 |
1/2'' NPT Off line |
| 554 |
1'' NPT Off line |
| 555 |
Cell DN50 PN16-400 |
| 556 |
Cell DN80 PN16-400 |
| 557 |
Cell DN100PN16-400 |
| 558 |
Cell 2''150-2500LBS |
| 559 |
Cell 3''150-2500LBS |
| 560 |
Cell 4''150-2500LBS |
| 561 |
TriClamp1''DN25-38 |
| 562 |
TriClamp2''DN40-51 |
| 563 |
TriClamp3''DN70-76 |
| 564 |
PipeTriClamp1''DN25 |
| 565 |
PipeTriClamp1 1/2'' |
| 566 |
PipeTriClamp2''DN51 |
| 567 |
VarivPipeDN40-162 |
| 568 |
DRD65mm PN25 |
| 569 |
SanTankSpud Tub2'' |
| 570 |
DIN11851DN50PN25 |
| 571 |
DIN11851DN65PN25 |
| 572 |
DIN11851DN80PN25 |
| 573 |
REMOTE SEAL - |
| 574 |
DIAPHRAG.MAT. + |
| 575 |
Alloy C 276 |
| 576 |
316L Gold-Rhodium |
| 577 |
316L PTFE-Foil |
| 578 |
FILL FLUID |
| 579 |
Silicon oil |
| 580 |
Mineral oil |
| 581 |
Inert oil |
| 582 |
High temp. Oil |
| 583 |
Vegetable oil |
| 584 |
Allowed Min.TEMP |
| 585 |
Allowed Max.TEMP |
| 586 |
MAT. MEMBRANE |
| 587 |
316L SST AuRh |
| 588 |
AlloyC22/C276 |
| 589 |
Tantalum |
| 590 |
316SST PTFE |
| 591 |
Ceramic |
| 592 |
FILLING FLUID |
| 593 |
Without |
| 594 |
SENS H/WARE REV |
| 595 |
RESET PEAKHOLD |
| 596 |
Max. Pressure |
| 597 |
Min. Pressure |
| 598 |
Pmax history |
| 599 |
Pmin history |
| 600 |
Max. Temp. |
| 601 |
Min. Temp. |
| 602 |
Tmax history |
| 603 |
Tmin history |
| 604 |
Reset All |
| 605 |
MIN. MEAS.PRESS. |
| 606 |
MAX. MEAS.PRESS. |
| 607 |
COUNTER:P < Pmin |
| 608 |
COUNTER:P > Pmax |
| 609 |
MIN. MEAS.TEMP. |
| 610 |
MAX. MEAS.TEMP. |
| 611 |
COUNTER:T < Tmin |
| 612 |
COUNTER:T > Tmax |
| 613 |
PCB MIN. TEMP. |
| 614 |
PCB MAX. TEMP. |
| 615 |
PCB COUNT:T<Tmin |
| 616 |
PCB COUNT:T>Tmax |
| 617 |
SENSOR CHANGES |
| 618 |
MEAS. VAL. TREND |
| 619 |
Constant |
| 620 |
Decreasing |
| 621 |
Increasing |
| 622 |
P PEAKHOLD.STEP |
| 623 |
FS |
| 624 |
T PEAKHOLD.STEP |
| 625 |
PRESS.SENS LOLIM |
| 626 |
PRESS.SENS HILIM |
| 627 |
Tmin SENSOR |
| 628 |
Tmax SENSOR |
| 629 |
SENSOR SER. No. |
| 630 |
0000000000000000 |
| 631 |
SENSOR MEAS.TYPE |
| 632 |
Differential |
| 633 |
Gauge |
| 634 |
Absolut |
| 635 |
multi |
| 636 |
DEVICE SERIAL No |
| 637 |
DEVICE DESIGN. |
| 638 |
TANK VOLUME |
| 639 |
TANK HEIGHT |
| 640 |
FULL HEIGHT |
| 641 |
EMPTY HEIGHT |
| 642 |
OUTPUT UNIT |
| 643 |
% |
| 644 |
LEVEL SELECTION |
| 645 |
Level Standard |
| 646 |
Level Easy Pressure |
| 647 |
Level Easy Height |
| 648 |
INP.PRESS INVERS |
| 649 |
MEASURED VALUE |
| 650 |
DEVICE NAME STR. |
| 651 |
CERABAR S |
| 652 |
CURRENT CHARACT. |
| 653 |
ENG. UNIT LEVEL |
| 654 |
TANK CONTENTUNIT |
| 655 |
CUST.UNIT FACT.L |
| 656 |
FACTOR TANK CONT |
| 657 |
LEVEL UNIT TXT |
| 658 |
CUST. UNIT CONT. |
| 659 |
DEVICE ID |
| 660 |
Status Signal |
| 661 |
Configuration Flag Reset |
| 662 |
Commands reset the configuration flag. |
| 663 |
SAFETY UN-/LOCK |
| 664 |
update_OperatingMode |
| 665 |
update_ConfigurationType |
| 666 |
update_LevelType |
| 667 |
update_MeasurandCombined |
| 668 |
update_FlowMode |
| 669 |
VIEW ALARMS SET. |
| 670 |
UpdateFlexAlarms |
| 671 |
Tansmitter spec command error |
| 672 |
Set to nearest possible value |
| 673 |
Invalid value selection |
| 674 |
Lower range value too small |
| 675 |
Upper range value too high |
| 676 |
Upper and Lower range value out of range |
| 677 |
Span too small |
| 678 |
Invalid span |
| 679 |
Offline |
| 680 |
MEASURING MODE |
| 681 |
QUICK SETUP |
| 682 |
DEVICE INFO |
| 683 |
UNITS |
| 684 |
RANGE VALUES |
| 685 |
LEVEL ADJUST |
| 686 |
ALARM SETTINGS |
| 687 |
OPERATING MENU |
| 688 |
SETTINGS |
| 689 |
POSITION ADJUST. |
| 690 |
BASIC SETUP |
| 691 |
EXTENDED SETUP |
| 692 |
LINEARIZATION |
| 693 |
SAFETY CONFIRM. |
| 694 |
DISPLAY |
| 695 |
OUTPUT |
| 696 |
TRANSMITTER INFO |
| 697 |
HART DATA |
| 698 |
TRANSMITTER DATA |
| 699 |
PROCESS CONNECTION |
| 700 |
SENSOR DATA |
| 701 |
PROCESS INFO |
| 702 |
PROCESS VALUES |
| 703 |
PEAK HOLD INDIC. |
| 704 |
OPERATION |
| 705 |
DIAGNOSTICS |
| 706 |
SIMULATION |
| 707 |
MESSAGES |
| 708 |
CONF.FLEX ALARMS |
| 709 |
Safety relevant events as alarm or warning |
| 710 |
'Alarm' affects AO |
| 711 |
Safety relevant events as alarm |
| 712 |
SFF relevant event |
| 713 |
Not Safety relevant events |
| 714 |
USER LIMITS |
| 715 |
SERVICE |
| 716 |
SYSTEM 1 |
| 717 |
SYSTEM 2 |
| 718 |
SENSOR TRIM |
| 719 |
Upload variables |
| 720 |
Device ICON |
| 721 |
Device Information |
| 722 |
Device Status |
| 723 |
Configure/Setup |
| 724 |
Identification |
| 725 |
Sensor Limits |
| 726 |
Range Values |
| 727 |
Zero Adjust |
| 728 |
Empty Calibration |
| 729 |
Full Calibration |
| 730 |
Please set 'LEVEL MODE' to 'Linear' and 'CALIBRATION MODE' to 'Wet', or go to the 'OPERATING MENU/SETTINGS' menu. |
| 731 |
BASIC SETUP 1/4 |
| 732 |
BASIC SETUP 2/4 |
| 733 |
BASIC SETUP 3/4 |
| 734 |
BASIC SETUP 4/4 |
| 735 |
BASIC SETUP 1/2 |
| 736 |
BASIC SETUP 2/2 |
| 737 |
LINEARIZATION 1/2 |
| 738 |
LINEARIZATION 2/2 |
| 739 |
Config.invalid for Safety Lock Reset 7864 needed ! |
| 740 |
Configuration invalid for Safety Lock!
Please check the Parameter/Alarm settings: |
| 741 |
- 'PRESS. ENG. UNIT'<>'User unit'. |
| 742 |
- 'CURRENT MODE'='Enabled'. |
| 743 |
- 'CURRENT CHARACT'='linear'. |
| 744 |
- 'ALT.CURR.OUTPUT'='Normal/NE43'. |
| 745 |
- 'OUTPUT FAIL MODE'='Min. Alarm(-10%)' or 'Max. Alarm (110%)'. |
| 746 |
- 'ALARM DELAY'='0.0s'. |
| 747 |
- 'ALARM DISPL.TIME'='0.0s'. |
| 748 |
- 'E726 Sen temp range'='Alarm'. |
| 749 |
- 'E716 Diaphr. broken'='Alarm'. |
| 750 |
Safe Commissioning |
| 751 |
Config flexible alarms |
| 752 |
To modify the settings please go to the 'DIAGNOSTICS/MESSAGE' menu. |
| 753 |
Shows current and allowable settings for safety relevant messages: |
| 754 |
Note:
[ ] Warning
[x] Alarm affects Analog Output |
| 755 |
Setting 'E727 Sen overrange' to alarm will improve the SFF/llambda-du values. Refer to SD0189/SD0190. Alarm setting is required if same values as used in Firmware <=02.20.04 are needed. |
| 756 |
BasicSetup |
| 757 |
CurrentOutput |
| 758 |
Display |
| 759 |
ExtendedSetup |
| 760 |
HartData |
| 761 |
Linearisation |
| 762 |
Operation |
| 763 |
PeakHold |
| 764 |
ProcessConnection |
| 765 |
ProcessValues |
| 766 |
SensorData |
| 767 |
Service |
| 768 |
SilMode |
| 769 |
Totalizer |
| 770 |
UserLimits |
| 771 |
Linewriter |
| 772 |
Measured Values |
| 773 |
CORRECTED PRESS. |
| 774 |
PCB TEMPERATURE |
| 775 |
SUPPRESSED FLOW |
| 776 |
TOTALIZER 1 |
| 777 |
TOTALIZER 2 |
| 778 |
PV |
| 779 |
Displays the primary value |
| 780 |
Primary value |
| 781 |
SV |
| 782 |
Displays the second process value |
| 783 |
Secondary value |
| 784 |
TV |
| 785 |
Displays the third process value |
| 786 |
Third value |
| 787 |
QV |
| 788 |
Displays the fourth process value |
| 789 |
4th value |
| 790 |
Process Variables |
| 791 |
HART Output |
| 792 |
OUTPUT CURRENT |
| 793 |
MEASURED VALUE |
| 794 |
Device Diagnostics |
| 795 |
HART DIAGNOSTICS |
| 796 |
FIELD DEVICE STATUS |
| 797 |
STATUS BYTE 1 |
| 798 |
STATUS BYTE 2 |
| 799 |
STATUS BYTE 3 |
| 800 |
STATUS BYTE 4 |
| 801 |
STATUS BYTE 5 |
| 802 |
STATUS BYTE 6 |
| 803 |
STATUS BYTE 7 |
| 804 |
STATUS BYTE 8 |
| 805 |
STATUS BYTE 9 |
| 806 |
HartLogo |
| 807 |
Maintenance |
| 808 |
PV Analog Channel Saturated |
| 809 |
PV Analog Channel Fixed |
| 810 |
Wireless |
| 811 |
WirelessHART Device |
| 812 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 813 |
Primary |
| 814 |
Primary Analog Channel |
| 815 |
Secondary |
| 816 |
Secondary Analog Channel |
| 817 |
Tertiary |
| 818 |
Tertiary Analog Channel |
| 819 |
Quaternary |
| 820 |
Quaternary Analog Channel |
| 821 |
Quinary |
| 822 |
Quinary Analog Channel |
| 823 |
Critical Power Failure |
| 824 |
Lock all |
| 825 |
Trim not supported |
| 826 |
Configuration cannot be changed |
| 827 |
Locked by gateway |
| 828 |
Analog Input Channel |
| 829 |
Analog Output Channel |
| 830 |
Secondary Analog Channel Saturated |
| 831 |
Tertiary Analog Channel Saturated |
| 832 |
Quaternary Analog Channel Saturated |
| 833 |
Quinary Analog Channel Saturated |
| 834 |
Secondary Analog Channel Fixed |
| 835 |
Tertiary Analog Channel Fixed |
| 836 |
Quaternary Analog Channel Fixed |
| 837 |
Quinary Analog Channel Fixed |
| 838 |
Simulation active |
| 839 |
The device is in simulation mode and the level output is not representative of the process. |
| 840 |
Non-Volatile memory failure |
| 841 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 842 |
Volatile memory error |
| 843 |
The RAM memory check is invalid or maybe corrupt |
| 844 |
Watchdog reset executed |
| 845 |
A watchdog reset has been performed |
| 846 |
Voltage conditions out of range |
| 847 |
A voltage condition is outside its allowable range |
| 848 |
Environmental conditions out of range |
| 849 |
An internal or environmental condition is beyond acceptable limits. |
| 850 |
Electronic failure |
| 851 |
A hardware problem not related to the sensor has been detected. |
| 852 |
Subdevice list changed |
| 853 |
Duplicate master detected |
| 854 |
Capacity Denied |
| 855 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 856 |
Bandwidth allocation pending |
| 857 |
Block transfer pending |
| 858 |
Battery life |
| 859 |
Percent range |
| 860 |
Loop current |
| 861 |
Primary variable |
| 862 |
Secondary variable |
| 863 |
Tertiary variable |
| 864 |
Quaternary variable |
| 865 |
Read receive time |
| 866 |
Write date and time |
| 867 |
Non-Volatile Clock |
| 868 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 869 |
Clock Uninitialized |
| 870 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 871 |
No restrictions |
| 872 |
SI Only |
| 873 |
Restricted to SI Unit codes only |
| 874 |
Process automation device |
| 875 |
Discrete device |
| 876 |
Hybrid:Process automation+discrete |
| 877 |
I/O System |
| 878 |
WirelessHART Process automation device |
| 879 |
WirelessHART Discrete device |
| 880 |
WirelessHART Process automation+discrete |
| 881 |
WirelessHART Gateway |
| 882 |
WirelessHART Access point |
| 883 |
WirelessHART Process adapter |
| 884 |
WirelessHART Discrete adapter |
| 885 |
WirelessHART enabled handheld/portable maintenance tool |
| 886 |
Device Profile |
| 887 |
US |
| 888 |
United States of America |
| 889 |
JP |
| 890 |
Japan |
| 891 |
DE |
| 892 |
Germany |
| 893 |
FR |
| 894 |
France |
| 895 |
ES |
| 896 |
Spain |
| 897 |
RU |
| 898 |
Russian Federation |
| 899 |
CN |
| 900 |
People's Republic of China |
| 901 |
Secondary Master |
| 902 |
Primary Master |
| 903 |
Device Diagnostic Status 0 |
| 904 |
Device Diagnostic Status 1 |
| 905 |
I/O and Subdevice Status |
| 906 |
WirelessHART Status |
| 907 |
Time Set Option |
| 908 |
Real Time Clock Flags |
| 909 |
Country |
| 910 |
Country of intended device installation |
| 911 |
SI Unit Control |
| 912 |
Indicates if device should only display SI unit codes |
| 913 |
Time Stamp |
| 914 |
Relative time value on network |
| 915 |
8u |
| 916 |
Dynamic Variables Returned for Device Variables |
| 917 |
Command Response Truncated |
| 918 |
Configuration Change Counter Mismatch |
| 919 |
Status bytes mismatch |
| 920 |
count |
| 921 |
Device Variable |
| 922 |
Variable to trim |
| 923 |
Good |
| 924 |
Failure
B>Sensor electronic EEPROM error A101
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2. Sensor defect.
Remedy:
1.1.Wait a few minutes.
1.2.Restart the device. Perform reset(Code 62).
1.3.Block off electromagnetic effects or eliminate source of disturbance.
2.Replace sensor. |
| 925 |
Failure
B>Checksum error in EEPROM:configuration segment A110
Cause:
1.The supply voltage is disconnected when writing.
2.Electromagnetic effects are greater than specifications in the technical data.
3.Main electronics defect.
Remedy:
1.Reestablish supply voltage. Perform reset (Code 7864) if necessary. Carry out calibration again.
2.Block off electromagnetic effects or eliminate sources of disturbance.
3.Replace main electronics. |
| 926 |
Failure
B>ROM failure in Transmitter electronic A113
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 927 |
Maintenance req.
C>Download error repeat download W116
Cause:
1.The file is defect.
2.During the download, the data are not correctly transmitted to the processor, e.g. because of open cable connections, spikes (ripple) on the supply voltage or electromagnetic effects.
Remedy:
1.Use another file.
2.1.Check cable connection PC -transmitter.
2.2.Block off electromagnetic effects or eliminate sources of disturbance.
2.3.Perform reset (Code 7864) and carry out calibration again.
2.4.Repeat download. |
| 928 |
Failure
B>Checksum Error in factory segment of EEPROM A121
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 929 |
Failure
B>Sensor not connected! A122
Cause:
1.Cable connection sensor -main electronics disconnected.
2.Electromagnetic effects are greater than specifications in the technical data.
3.Main electronics defect.
4.Sensor defect.
Remedy:
1.Check cable connection and repair if necessary.
2.Block off electromagnetic effects or eliminate source of disturbance.
3.Replace main electronics.
4.Replace sensor. |
| 930 |
Failure
B>EEPROM is defect A130
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 931 |
Failure
B>Checksum error in EEPROM: minMAX segment A131
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 932 |
Failure
B>Checksum Error in Totalizer EEPROM A132
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 933 |
Failure
B>Checksum Error in History EEPROM A133
Cause:
1.An error occurred when writing.
2.Main electronics defect.
Remedy:
1.Perform reset (Code 7864) and carry out calibration again.
2.Replace electronics. |
| 934 |
Failure
B>Checksum error in EEPROM:FF segment A135
Cause:
Main electronics defect.
Remedy:
Replace main electronics. |
| 935 |
Function check
C>Linearizations curve not monoton W602
Cause:
The linearisation table is not monotonic increasing.
Remedy:
Add to linearisation table or perform linearisation again. |
| 936 |
Function check
C>nLinearization:less than 2points or points too close W604
Cause:
1.The linearisation table consists of less than 2 points.
2.At least 2 points in the linearisation table are too close together. A minimum gap of 0.5% of the distance between two points must be maintained. Spans for the ''Pressure linearized'' option: HYDR.PRESS MAX. / HYDR. PRESS MIN.; TANK CONTENT MAX./TANK CONTENT MIN. Spans for the ''Height linearized'' option: LEVEL MAX/LEVEL MIN; TANK CONTENT MAX./TANK CONTENT MIN.
Remedy:
1.Add to linearisation table. If necessary, perform linearisation again.
2.Correct linearisation table and accept again. |
| 937 |
Failure
B>Measurement error A703
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 938 |
Function check
B>Measurement error A704
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 939 |
Failure
B>Measurement error A705
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 940 |
Failure
B>Sensor diaphragm broken E716
Cause:
Sensor defect.
Remedy:
Replace sensor. |
| 941 |
Failure
B>Sensor connection error cycle disturbed A725
Cause:
1.Electromagnetic effects are greater than specifications in the technical data.
2.Sensor or main electronics defect.
Remedy:
1.Block off electromagnetic effects or eliminate source of disturbance.
2.Replace sensor or main electronics. |
| 942 |
Failure
B>RAM error A728
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 943 |
Failure
B>RAM error A729
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 944 |
Failure
B>RAM error A736
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 945 |
Failure
B>Measurement error A737
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 946 |
Failure
B>Measurement error A738
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.Briefly disconnect device from the power supply.
2.Replace main electronics. |
| 947 |
Failure
B>Measurement error A739
Cause:
1.Fault in the main electronics.
2.Main electronics defect.
Remedy:
1.1.Wait a few minutes.
1.2.Perform reset(Code 7864) and carry out calibration again.
2.Check cable connection and repair if necessary.
3.Replace sensor. |
| 948 |
Failure
B>Sensor connection error (upload) A742
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2.Cable connection sensor -main electronics disconnected.
3.Sensor defect.
Remedy:
1.1.Wait a few minutes.
1.2.Perform reset (Code 7864) and carry out calibration again.
2.Check cable connection and repair if necessary.
3.Replace sensor. |
| 949 |
Failure
B>Electronic PCB error during initialisation A743
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2.Cable connection sensor -main electronics disconnected.
3.Sensor defect.
Remedy:
1.1.Restart the device. Perform reset(Code 62).
1.2.Block off electromagnetic effects or eliminate source of disturbance.
2.Replace main electronics. |
| 950 |
Failure
B>Main electronic PCB error A744
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2. Sensor defect.
Remedy:
1.1.Restart the device. Perform reset(Code 62).
1.2.Block off electromagnetic effects or eliminate source of disturbance.
2.Replace main electronics. |
| 951 |
Failure
B>Sensor-Software not compatible to electronics A747
Cause:
Sensor does not suit the device (electronic sensor nameplate).
Remedy:
Replace sensor with a suitable sensor. |
| 952 |
Failure
B>Memory failure in signal processor A748
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2.Cable connection sensor -main electronics disconnected.
3.Sensor defect.
Remedy:
1.Block off electromagnetic effectsor eliminate source of disturbance.
2.Replace main electronics. |
| 953 |
Function check
B>Configuration not allowed A750
Cause:
By means of the operation profile, options were selected for the configuration of the device but the options do not suit one another. For example, if the option ''1'' (linearisation table)was selected for LIN_TYPE and the unit m3/s was selected for PRIMARY_VALUE_UNIT.
Remedy:
1.1.Check configuration.
1.2.Perform reset (code 7864) and recalibrate the device. |
| 954 |
Function check
C>Downloading-please wait W106
Cause:
Downloading.
Remedy:
Wait for download to complete. |
| 955 |
Function check
I>Simulation is active! W613
Cause:
Simulation is switched on, i.e. the device is not measuring at present
Remedy:
Switch off simulation. |
| 956 |
Function check
C>Sensor connection error-initialising W746
Cause:
1.Electromagnetic effects are greater than specifications in the technical data. This message normally only appears briefly.
2.Overpressure or low pressure present.
Remedy:
1.1.Wait a few minutes.
1.2.Restart the device. Perform reset(Code 7864).
1.3.Block off electromagnetic effects or eliminate source of disturbance.
2.Reduce or increase pressure. |
| 957 |
Maintenance req.
C>Checksum error in EEPROM: peakhold segment W102
Cause:
Main electronics defect. Correct measurement can continue as long as you do not need the peak hold indicator function. |
| 958 |
Maintenance req.
C>Last Configuration not stored W700
Cause:
1.An error occurred when writing or reading configuration data or the power supply was disconnected.
Remedy:
1.Perform reset (Code 7864) and carry out calibration again.
2.Replace main electronics. |
| 959 |
Function check
C>Measuring chain config. exceeds sensor range W701 |
| 960 |
Maintenance req.
C>HistoROM data not consistent W702
Cause:
1.Data were not written correctly to the HistoROM, e.g. if the HistoROM was detached during the writing process.
2.HistoROM does not have any data.
Remedy:
1.1.Repeat upload.
1.2.Perform reset (Code 7864) and carry out calibration again.
2.Copy suitable data to the HistoROM. |
| 961 |
Maintenance req.
C>Configuration in HistoROM and device not identical W706
Cause:
Configuration (parameters) in the HistoROM and in the device is not identical. |
| 962 |
Function check
B>X-VAL of lin. table out of edit limits A707
Cause:
At least one X-VALUE in the linearisation table is either below the value for HYDR. PRESS MIN. or MIN. LEVEL or above the value for HYDR.PRESS. MAX. or LEVEL MAX.
Remedy:
Carry out calibration again. |
| 963 |
Function check
C>Set span too small Not allowed. W710
Cause:
1.Values for calibration (e.g. lower range value and upper range value) are too close together.
2.The sensor was replaced and the customer-specific configuration does not suit the sensor.
3.Unsuitable download carried out.
Remedy:
1.Adjust calibration to suit sensor.
2.1.Adjust calibration to suit sensor.
2.2.Replace sensor with a suitable sensor.
3.Check configuration and perform download again. |
| 964 |
Function check
B>LRV or URV out of edit limits A711
Cause:
1. Lower range value and/or upper range value undershoot or overshoot the sensor range limits.
2. The sensor was replaced and the customer-specific configuration does not suit the sensor.
3. Unsuitable download carried out.
Remedy:
1. Reconfigure lower range value and/or upper range value to suit the sensor. Pay attention to position factor.
2. Replace sensor with a suitable sensor.
3. Check configuration and perform download again. |
| 965 |
Function check
B>Y-VAL of lin. table out of edit limits A719
Cause:
At least on Y-VALUE in the linearisation table is below the MIN. TANK CONTANT or above the MAX.TANK CONTENT.
Remedy:
Carry out calibration again. |
| 966 |
Function check
B>ZERO POSITION level out of edit limits A721
Cause:
LEVEL MIN or LEVEL MAX has been changed.
Remedy:
Perform reset (Code 2710) and carry out calibration again. |
| 967 |
Function check
B>EMPTY CALIB. or FULL CALIB. out of edit limits A722
Cause:
LEVEL MIN or LEVEL MAX has been changed.
Remedy:
Perform reset (Code 2710) and carry out calibration again. |
| 968 |
Function check
B>MAX. FLOW out of edit limits A723
Cause:
FLOW-MEAS.TYPE has been changed.
Remedy:
Carry out calibration again. |
| 969 |
Maintenance req.
C>Calculation Overflow, bad configuration E740
Cause:
1.Level measuring mode: the measured pressure has undershot the value for HYDR.PRESS. MIN. or overshot the value for HYDR. PRESS MAX.
2.Level measuring mode: the measured level has undershot the value for LINEAR_LEVEL_MIN/LEVEL MIN or overshot the value for LINEAR_LEVEL_MAX/LEVEL MAX.
3.Flow measuring mode: the measured pressure has undershot the value for MAX. PRESS FLOW.
Remedy:
1.1.Check configuration and carry out calibration again if necessary.
1.2.Select a device with a suitable measuring range.
2.Check configuration and carry out calibration again if necessary.
3.1.Check configuration and carry out calibration again if necessary.
3.2. Select a device with a suitable measuring range. |
| 970 |
Function check
B>TANK HEIGHT out of edit limits A741
Cause:
LEVEL MIN or LEVEL MAX has been changed.
Remedy:
Perform reset (Code 2710) and carry out calibration again. |
| 971 |
Maintenance req.
C>Sensor data unknown W745
Cause:
Sensor does not suit the device(electronic sensor nameplate). Device continues measuring.
Remedy:
Replace sensor with a suitable sensor. |
| 972 |
Out of Spec.
C>Sensor over pressure E115
Cause:
1.Overpressure present.
2.Sensor defect.
Remedy:
1.Reduce pressure until message disappears.
2.Replace sensor. |
| 973 |
Out of Spec.
C>Sensor low pressure E120
Cause:
1.Pressure too low.
2.Sensor defect
Remedy:
1.Increase pressure until message disappears.
2.Replace sensor. |
| 974 |
Out of Spec.
C>Current output out of range E620 |
| 975 |
Function check
B>100% POINT level out of edit limits A713
Cause:
The sensor was replaced.
Remedy:
Carry out calibration again. |
| 976 |
Out of Spec.
C>Sensor over temperature E715
Cause:
1.The temperature measured in the sensor is greater than the upper nominal temperature of the sensor.
2.Unsuitable download carried out.
Remedy:
1.Reduce process temperature/ambient temperature.
2.Check configuration and perform download again. |
| 977 |
Out of Spec.
C>Transmitter over temperature E717
Cause:
1.The temperature measured in the electronics is greater than the upper nominal temperature of the electronics (+88 °C).
2.Unsuitable download carried out.
Remedy:
1.The temperature measured in the electronics is greater than the upper nominal temperature of the electronics (+88 °C).
2.Unsuitable download carried out. |
| 978 |
Out of Spec.
C>Transmitter under temperature E718
Cause:
1.The temperature measured in the electronics is smaller than the lower nominal temperature of the electronics (-43 °C).
2.Unsuitable download carried out.
Remedy:
1.The temperature measured in the electronics is smaller than the lower nominal temperature of the electronics (-43 °C).
2.Unsuitable download carried out. |
| 979 |
Out of Spec.
C>Sensor under temperature E720
Cause:
1.The temperature measured in the sensor is smaller than the lower nominal temperature of the sensor.
2.Unsuitable download carried out.
3.Loose connection at sensor cable.
Remedy:
1.Increase process temperature/ambient temperature.
2.Check configuration and perform download again.
3.Wait a short period of time and tighten the connection, or avoid loose connection. |
| 980 |
Out of Spec.
C>Sensor temperature error-overrange E726
Cause:
1.Electromagnetic effects are greater than specifications in the technical data.
2.Process temperature is outside permitted range.
3.Sensor defect.
Remedy:
1.Block off electromagnetic effects or eliminate source of disturbance.
2.Check temperature present,reduce or increase if necessary.
3.If the process temperature is within the permitted range,replace sensor. |
| 981 |
Out of Spec.
C>Sensor pressure error-overrange E727
Cause:
1.Electromagnetic effects are greater than specifications in the technical data.
2.Pressure is outside permitted range.
3.Sensor defect.
Remedy:
1.Block off electromagnetic effects or eliminate source of disturbance.
2.Check pressure present, reduce or increase if necessary.
3.If the pressure is within the permitted range, replace sensor. |
| 982 |
Out of Spec.
C>LRV user limits exceeded E730
Cause:
1.Pressure measured value has undershot the value specified for the Pmin ALARM WINDOW parameter.
2.Loose connection at sensor cable.
Remedy:
1.1.Check system/pressure measured value.
1.2.Change value for Pmin ALARM WINDOW if necessary.
2.Wait a short period of time and tighten the connection, or avoid loose connection. |
| 983 |
Out of Spec.
C>URV user limits exceeded E731
Cause:
Pressure measured value has overshot the value specified for the Pmax ALARM WINDOW parameter
Remedy:
1.1.Check system/pressure measured value.
1.2.Change value for Pmax ALARM WINDOW if necessary. |
| 984 |
Out of Spec.
C>LRV-Temp. user limits exceeded E732
Cause:
1.Temperature measured value has undershot the value specified for Tmin ALARM WINDOW parameter.
2.Loose connection at sensor cable.
Remedy:
1.1.Check system/temperature measured value.
1.2.Change value for Tmin ALARM WINDOW if necessary.
2.Wait a short period of time and tighten the connection, or avoid loose connection. |
| 985 |
Out of Spec.
C>URV-Temp. user limits exceeded E733
Cause:
Temperature measured value has overshot the value specified for the Tmax ALARM WINDOW parameter.
Remedy:
1.1.Check system/temperature measured value.
1.2.Change value for Tmax ALAR MWINDOW if necessary. |
| 986 |
Execute Configuration Flag Reset? |
| 987 |
Configuration invalid for Safety Lock!
Please check the Parameter/Alarm settings: |
| 988 |
|
| 989 |
Config.invalid for Safety Lock Reset 7864 needed ! |
| 990 |
- 'PRESS. ENG. UNIT'<>'User unit'. |
| 991 |
- 'CURRENT CHARACT'='linear'. |
| 992 |
- 'ALARM DELAY'='0.0s'. |
| 993 |
HW Lock state is ON. Check Dip switch! |
| 994 |
Software Lock active! |
| 995 |
System is working, please wait |
| 996 |
SAFETY LOCKSTATE
>%{0} |
| 997 |
Lock |
| 998 |
Unlock |
| 999 |
Config.invalid for Safety Lock. |
| 1000 |
DIGITS SET
>%{0} |
| 1001 |
Invalid;Valid |
| 1002 |
OUTPUT FAIL MODE
>%{0} |
| 1003 |
SET MIN. CURRENT
>%{1} |
| 1004 |
SET MAX. ALARM
>%{2} mA |
| 1005 |
E727 Sen overrange
>Alarm |
| 1006 |
E727 Sen overrange
>Warning |
| 1007 |
ACK. ALARM MODE
>%{2} |
| 1008 |
CALIB. OFFSET
>%{3} %{4} |
| 1009 |
MEASURING MODE
>%{5} |
| 1010 |
SET LRV
>%{0} %{2} |
| 1011 |
SET URV
>%{1} %{2} |
| 1012 |
DAMPING VALUE
>%[.1f]{6} s |
| 1013 |
Safety Lock active! |
| 1014 |
The code is not correct.
Enter the code to lock the parameters.
|
| 1015 |
Not all parameters were confirmed
Please repeat the procedure |
| 1016 |
Not Supported for Actual Op. Mode! |
| 1017 |
Safety Lock deactivated! |
| 1018 |
The code is not correct.
Enter the code to unlock the parameters.
|
| 1019 |
Config.invalid for Safety Lock!
Please check the parameter 'CURRENT MODE'=Signaling! |
| 1020 |
EMPTY PRESSURE
>%[.4f]{0} %{7} |
| 1021 |
EMPTY CALIB.
>%[.4f]{1} %{6} |
| 1022 |
FULL PRESSURE
>%[.4f]{2} %{7} |
| 1023 |
FULL CALIB.
>%[.4f]{3} %{6} |
| 1024 |
SET LRV
>%[.4f]{4} %{6} |
| 1025 |
SET URV
>%[.4f]{5} %{6} |
| 1026 |
Get LRV was not done |
| 1027 |
Apply low pressure |
| 1028 |
Get LRV
Pressure >%{0} %{1} |
| 1029 |
Abort;Confirm |
| 1030 |
Device lock active! |
| 1031 |
Get URV was not done |
| 1032 |
Apply hi pressure |
| 1033 |
Get URV
Pressure: %{0} %{1} |
| 1034 |
Pos.Zero Adjust was not done |
| 1035 |
Pos.Zero Adjust
Pressure: %{0} %{1} |
| 1036 |
Trim was not done |
| 1037 |
Press OK when pressure is stable |
| 1038 |
Enter applied pressure value
Pressure: %{0} %{1} |
| 1039 |
trim_point |
| 1040 |
Remove pressure |
| 1041 |
Service unlock necessary. |
| 1042 |
Enter Reset Code |
| 1043 |
NOTICE - After Reset you have to reconnect the device to the HART or restart the Application - otherwise there might be inconsistence. |
| 1044 |
Reset in progress !
- please wait 30 seconds - |
| 1045 |
Wrong Reset Code ! |
| 1046 |
Abort;HistoROM->Device;Device->HistoROM |
| 1047 |
Unexpected Error Command %{iCmd} |
| 1048 |
WARNUNG:
After Downloading you have to reconnect the device to the HART - otherwise there might be inconsistence. |
| 1049 |
INFO: HistoROM->Device
Downloading-please wait W106 |
| 1050 |
INFO: Device->HistoROM
Uploading-please wait W106 |
| 1051 |
HistoROM is not available! |
| 1052 |
TABLE EDITOR |
| 1053 |
Next Point;Last Input Point;Accept input table |
| 1054 |
NEXT > |
| 1055 |
select |
| 1056 |
< BACK;NEXT > |
| 1057 |
< BACK;FINISH |
| 1058 |
Please set 'LEVEL MODE' to 'Linear' and 'CALIBRATION MODE' to 'Wet', or go to the 'OPERATING MENU/SETTINGS' menu. |