Device dictionary

Loading…

Reference ID	String
0	SENSOR OVERPRESSURE REFER TO MANUAL ERROR NO. 120
1	UP-/DOWN LOAD ACTIVE REFER TO MANUAL ERROR NO. 106
2	DOWN-LOAD ERROR REFER TO MANUAL ERROR NO. 116
3	MANUAL CURVE NOT COMPLETE NOT USABLE ERROR NR. 605
4	MANUAL CURVE NO. OF LINEARIZATION POINTS < 2 WARNING NR. 604
5	LINEARIZATION FAILURE LINEARIZATION POINTS WARNING NR. 602
6	VALUES ARE OUTSIDE SENSOR LIMITS ERROR NO. 118
7	ZERO (LRV) WAS NOT ACCEPTED WARNING NO. 670
8	20MA VALUE (URV) WAS NOT ACCEPTED WARNING NO. 671
9	ZERO VALUE (LRV) REACHED SENSOR LIMITS(LRL / URL) WARNING NO. 672
10	20MA VALUE (URV) REACHED SENSOR LIMITS(LRL / URL) WARNING NO. 673
11	VALUE WAS NOT ACCEPTED TURN DOWN TOO HIGH WARNING NO. 674
12	PRESSURE IS OUTSIDE SENSOR_LIMITS P < LRL / P> URL WARNING NO. 675
13	OPERATING MODE SIMULATION WARNING NO. 613
14	SLOPE CALIBRATION SENSOR REFER TO MANUAL WARNING NO. 104
15	CURRENT OUT OF RANGE REFER TO MANUAL WARNING NO. 620
16	Square root
17	Pressure %
18	Level linear
19	Level hor. cyl.
20	Level manual
21	mbar
22	bar
23	Pa
24	hPa
25	kPa
26	MPa
27	mmH2O
28	mH2O
29	inH2O
30	ftH2O
31	psi
32	g/cm2
33	kg/cm2
34	kgf/cm2
35	atm
36	lb/ft2
37	Torr
38	mmHg
39	inHg
40	%
41	ft3min
42	m3/h
43	l/s
44	ft3/s
45	m3/s
46	Nm3/h
47	Sft3mn
48	m3/min
49	USG/h
50	USG/d
51	Mgal/d
52	g/min
53	kg/s
54	kg/min
55	kg/h
56	t/min
57	t/h
58	t/d
59	lb/s
60	lb/min
61	lb/hr
62	Special
63	cm
64	dm
65	m
66	inch
67	ft
68	l
69	hl
70	cm3
71	dm3
72	m3
73	ft3
74	USgal
75	i_gal
76	ton
77	kg
78	t
79	lb
80	m3*10
81	m3*100
82	ft3*10
83	ft3*100
84	igal
85	Applied pressure too low
86	Span too small
87	Applied pressure too high
88	Set max current
89	5.2f
90	Zero correction
91	.4f
92	Zero corr. value
93	COUNTER
94	7.0f
95	DISPLAY SELECTOR
96	Flow
97	Totalizer
98	TOTALIZER OP.MODE
99	Totalizer: Off
100	neg.flow:Stop
101	neg.flow:Decr.
102	neg.flow:Incr.
103	CONVERSION FACTOR
104	.8f
105	COUNTER UNIT
106	LINEARIZATION
107	ACTIVATE TABLE
108	MANUAL
109	SEMIAUTOMATIC
110	CLEAR
111	LINE NO.
112	POINT 1
113	POINT 2
114	POINT 3
115	POINT 4
116	POINT 5
117	POINT 6
118	POINT 7
119	POINT 8
120	POINT 9
121	POINT 10
122	POINT 11
123	POINT 12
124	POINT 13
125	POINT 14
126	POINT 15
127	POINT 16
128	POINT 17
129	POINT 18
130	POINT 19
131	POINT 20
132	POINT 21
133	INPUT LEVEL
134	6.4f
135	INPUT VOLUME
136
137	PERCENT RANGE
138	%
139	6.1f
140	Min. Span
141	SERIAL-NO. SENS.
142	7d
143	FORMAT
144	SELECT PRESS.UNIT
145	TEMPERATURE UNIT
146	deg. C
147	deg. F
148	KELVIN
149	UNIT AFTER LIN.
150	NO UNIT
151	PERCENT
152	CURRENT UNIT
153	mA
154	MEASURED VALUE
155	6.0f
156	7.1f
157	7.2f
158	7.3f
159	7.4f
160	SET 4 mA VALUE
161	SET 20 mA VALUE
162	SET BIAS PRESSURE
163	SET OUTPUT DAMP.
164	s
165	.1f
166	SET OUTPUT SAFETY
167	MIN
168	MAX
169	CONTINUE
170	DIAGNOSTIC CODE
171	4d
172	LAST DIAGNOSTIC
173	INSTR.&SOFTW.NO
174	MIN. PRESSURE
175	MAX. PRESSURE
176	INT. COUNTER HIGH
177	3d
178	SENSOR TEMPERAT.
179	MIN. TEMPERATURE
180	MAX. TEMPERATURE
181	DEFAULT VALUES
182	OPERATING MODE
183	Square root
184	DISPLAY AT 4 mA
185	DISPLAY AT 20 mA
186	DENSITY FACTOR
187	CREEP FLOW SUPPR.
188	UNBIASED PRESSURE
189	BIASED PRESSURE
190	SECURITY LOCKING
191	CURRENT
192	mA
193	SIM. CURRENT
194	OFF
195	ON
196	MIN. CURRENT 4mA
197	LOW SENSOR CAL.
198	HIGH SENSOR CAL.
199	LOW SENSOR LIMIT
200	HIGH SENSOR LIMIT
201	SENSOR PRESSURE
202	SET USER TEXT
203	SERIAL NUMBER
204	8d
205	10u
206	PROCESS CONN. P+
207	Carbon steel
208	304 Stainl Stl
209	316 Stainl Stl
210	Hastelloy C
211	Monel
212	Tantalum
213	Titanium
214	PTFE
215	316L Stainl Stl
216	PVC
217	Inconel
218	ECTFE
219	PROCESS CONN. P-
220	GASKET
221	FPM Viton
222	NBR
223	EPDM
224	Urethane
225	IIR
226	Kalrez
227	FPM Viton Oxyg.
228	CR
229	MVQ
230	PROCESS DIAPHRAM.
231	Ceramic
232	FILL LIQUIT
233	Silicon oil
234	Vegetable oil
235	Glycerin
236	Inert oil
237	High temp. oil
238	CERABAR S
239	SET TAG NUMBER
240	6u
241	GAUGE DATA FRAM NOT STORED ERROR NO. 110
242	INITIALIZATION PLEASE WAIT WARNING NO. 103
243	CHECKSUM ERROR REFER INSTR. MANUAL ERROR NO. 101
244	CHECK SENSOR AND SENSOR WIRING REFER TO MANUAL ERROR NO. 111
245	CHECK SENSOR AND SENSOR WIRING REFER TO MANUAL ERROR NO. 112
246	CHECK SENSOR AND SENSOR WIRING REFER TO MANUAL ERROR NO. 113
247	CHECK SENSOR AND SENSOR WIRING REFER TO MANUAL ERROR NO. 114
248	SENSOR OVERPRESSURE REFER TO MANUAL ERROR NO. 115
249	POST_EDIT_37
250	POST_EDIT_38
251	POST_EDIT_39
252	4 mA VALUE AUTOM.
253	Current applied process value: >%{0} %{1}
254	Set as 4 mA value;Read new value
255	20 mA VALUE AUTOM.
256	Set as 20 mA value;Read new value
257	BIAS PRES. AUTOM.
258	Set as bias value;Read new value
259	LOW SENSOR CAL. DAMPED PRESSURE >%{0} %{1}
260	fval
261	HIGH SENSOR CAL. DAMPED PRESSURE >%{0} %{1}
262	ABORT SIMULATION
263	ABORT DYNAMIC
264	Reset value?
265	Yes;No
266	LAST DIAGNOSTIC >%{0}
267	MIN. PRESSURE >%{0} %{1}
268	MAX. PRESSURE >%{0} %{1}
269	INT. COUNTER HIGH %{0}
270	MIN. TEMPERATURE >%{0} %{1}
271	MAX. TEMPERATURE >%{0} %{1}
272	TOTALIZER
273	SERVICE
274	CALIBRATION
275	TRANSMITTER INFO
276	ADDITIONAL FUNCT.
277	USER INFORMATION
278	MATRIX PARAMETERS
279	DEVICE DATA
280	HART OUTPUT
281	OFFLINE
282
283	%-RANGE
284	temperature_digital_units_help
285	temperature_digital_value_help
286	Set to nearest possible value
287	Invalid value selection
288	ZERO CORRECTION DAMPED PRESSURE >%{0} %{1}
Reference ID	String