HART设备字典

Loading…

引用ID	字符串
0	UD10
1	DET-TRONICS
2	Operating Mode
3	Display Status 1
4	Cal Line Active
5	Cal Sw Active
6	HART Test
7	LON Attached
8	Response Test
9	Manual Self Test
10	Input HART
11	Reserved
12	Display Status 2
13	Any Fault
14	Cal Active
15	Warm Up Mode
16	Low Relay Active
17	Hi Relay Active
18	Aux Relay Active
19	Current Fixed
20	MB Write Protect
21	Device Status 1
22	Calibration Active
23	Warm Up
24	Low Alarm
25	Aux Alarm
26	High Alarm
27	Self Test
28	Configuration Change
29	Alignment Mode
30	Device Status 2
31	Write Protect
32	4-20 Fixed
33	Sensor Removed
34	Sensor End Of Life
35	Loop Test Active
36	Generic Status
37	Display Fault 1
38	12v Fault
39	5v Fault
40	3v Fault
41	Output Loop Fault
42	Input Loop Fault
43	Display Fault 2
44	FRAM Fault
45	ADC Ref Voltage Fault
46	24v Fault
47	Flash Fault
48	RAM Fault
49	WDT Fault
50	Device Fault 1
51	Loop Fault
52	Supply Voltage Fault
53	Calibration Fault
54	Memory Fault
55	ADC Fault
56	Internal Voltage Fault
57	Zero Drift
58	Temperature Sensor Fault
59	Device Fault 2
60	Wrong Sensor Type
61	Lamp Fault
62	Alignment Fault
63	Blocked Optic Fault
64	Sensor Fault
65	Noise Fault
66	Align ADC Fault
67	Device Fault 3
68	Align Fault
69	Align Warning
70	DAC Fault
71	High Fault
72	Low Fault
73	Device Warm Up
74	Device Fault 4
75	General Fault
76	Gas Value
77	.2f
78	%
79	Percentage Composition
80	PPM
81	PPM Meters
82	VOL
83	VOL Meters
84	%LFL
85	LEL Meters
86	PPB
87	PPB Units
88	---
89	User Defined Units
90	.3f
91	Analog Output
92	8.2f
93	Upper Range Value
94	10.2f
95	Lower Range Value
96	8.3f
97	Serial Number
98	7d
99	Request Index
100	Event Log Request
101	FIRST
102	PREV
103	NEXT
104	LAST
105	Response Index
106	TimeStamp
107	Cal Code
108	Empty Log
109	1
110	2
111	Zero_Cal
112	Span_Cal
113	Abort_Cal
114	Failed_Cal
115	7
116	8
117	9
118	10
119	Clr Cal Flt
120	Event Code
121	No Event
122	Power Up
123	Low Alarm On
124	High Alarm On
125	Aux Alarm On
126	Cal Flt On
127	Cal Active On
128	EE Flt On
129	ADC Ref Flt On
130	24v Flt On
131	Flash Flt On
132	RAM Flt On
133	WDT Flt On
134	12V Flt On
135	5V Flt On
136	3 V Flt On
137	ADC Range Flt On
138	Out Loop Flt On
139	In Loop Flt On
140	No HART Flt On
141	High Flt On
142	Low Flt On
143	Zero Drift Flt On
144	Optics Flt On
145	Low Voltage On
146	Cal Active Strt On
147	Active ADC Flt On
148	Active ADC Sat Flt On
149	Low Alarm Off
150	High Alarm Off
151	Aux Alarm Off
152	Cal Flt Off
153	Cal Active Off
154	EE Flt Off
155	ADC Ref Flt Off
156	24v Flt Off
157	Flash CRC Flt Off
158	RAM Flt Off
159	EX WDT Flt Off
160	12v Flt Off
161	5v Flt Off
162	3v Flt Off
163	ADC Range Flt Off
164	Out Loop Flt Off
165	In Loop Flt Off
166	Flash Flt Off
167	No HART Flt Off
168	High Flt Off
169	Low Flt Off
170	Zero Drift Flt Off
171	Optics Flt Off
172	Low Volt Flt Off
173	Cal Active Strt Flt Off
174	Active ADC Flt Off
175	Active ADC Sat Flt Off
176	Bank 1 Repaired
177	Bank 2 Repaired
178	Input Loop Cal Failed
179	Mode Changed
180	Zero Value
181	10.8f
182	Span Value
183	Low Alarm Level
184	Gas level for initiating a low alarm. The low alarm level can not be set lower than 5%LEL*M or higher than the high alarm level.
185	High Alarm Level
186	Gas level for initiating a high alarm. The high alarm level can not be set higher than 60%LEL*M or lower than the low alarm level.
187	Auxilary Alarm Level
188	Gas level for initiating an auxilary alarm.
189	Aux Alarm Latch
190	Selects latching or nonlatching aux alarm. Latched alarms are unlatched with Reset.
191	High Alarm Latch
192	Selects latching or nonlatching high alarm. Latched alarms are unlatched with Reset.
193	Low Alarm Latch
194	Selects latching or nonlatching low alarm. Latched alarms are unlatched with Reset.
195	Password
196	The password is used to validate the command to enable or disable writes in the device.
197	Set Write protect
198	Used to set the write protect mode.
199	Change Password
200	Local Zero Value
201	Local zero value.
202	Max Temp -Time
203	Min Temp -Time
204	Self test will perform all internal checks immediately and return results in variables xmtr flt 1 & xmtr flt 2.
205	This command will reset latched relay outputs
206	Firmware Revision
207
208	Hardware Revision
209	Response test
210	This test holds the analog output at 4mA and prevents the alarm relays from activating when gas is applied. Gas response is indicated by the PV.
211	Abort response test
212	Return to normal
213	Reset Latched Alarms
214	This command will reset the latched alarms
215	Calibration log
216	Retrieves stored calibration events. The most recent calibration event is shown first. Calibrations are recorded as zero only cal, cal OK & cal failed. Cal OK indicates that both zero and span were completed.
217	Event log
218	Retrieves stored events. The most recent event is shown first. Recorded events include Blocked Optics, warm up, zero drift, low alarm & high alarm.
219	Change Mode
220	DD Build Version
221	Internal DD build version number.
222	Display History
223	History
224	Display Fault/Status Info
225	Display Info
226	Device Status Menu
227	Device History Info
228	Device Setup
229	Device HART Option
230	Device Info
231	Device Fault/Status
232	Device Info 2
233	Sensor Info
234	Alarm Setting
235	Display HART Option
236	Main Menu
237	Process Variables
238	Display Status Menu
239	Display Setup
240	Display Test Menu
241	Display General Info
242	Display RTC
243	Write variables
244	Seconds
245	RTC seconds value 1-59.
246	Minutes
247	RTC minutes value 1-59.
248	Hours
249	RTC hours value 1-23.
250	Week
251	Month
252	RTC month value 1-12.
253	Invalid
254	Jan
255	Feb
256	Mar
257	Apr
258	May
259	Jun
260	Jul
261	Aug
262	Sep
263	Oct
264	Nov
265	Dec
266	Day
267	RTC day value 1-7.
268	Year
269	RTC year value 1-12.
270	Tx Running Hours
271	Sensitivity
272	Sensor Type
273	Sensor Part Number
274	Sensor Hardware Revision
275	Firmware Rev
276	Normal
277	Calibration in progress
278	Warm up
279	Calibration State
280	Waiting for Zero
281	Apply Clean Air
282	Waiting for Gas
283	Waiting for Span
284	Remove Cal Gas
285	Terminate
286	Complete
287	Hardware Rev
288	Revision
289	Universal Rev
290	Fld Dev Rev
291	Software Rev
292	Max Temp
293	3.2f
294	Running Hrs
295	Min Temp
296	Gas Name
297	Cal Gas Concentration
298	Response Factor
299	Manufacturer
300	Dev ID
301	Model
302	GT3000
303	X3301
304	OPECL_TX
305	OPECL_RX
306	ECLIPSE
307	PIR
308	Master Adrs Select
309	Primary
310	Secondary
311	Cal Point Zero
312	Cal Point Span
313	F
314	T
315	Error code not defined.
316	The real-time data returned from the field device has not changedsince the last time it was read OR The data sent to the field device has been rounded or truncated dueto limitations within the field device
317	This code indicates that the command was not executedNo Response Data Bytes are returned from the field device.
318	The requested (e.g., loop current) mode is not valid. This code indicates that the command was not executed.No Response Data Bytes are returned from the field device.
319	The requested command is not implemented
320	Tx Write protect error
321	FMU860
322	DT
323	DVC
324	FCX
325	AS800
326	340T
327	340C
328	344
329	Siemens Micro K
330	SITRANS L
331	SIPAN PH
332	SITRANS P
333	75SMT
334	UNIDELTA
335	8320
336	SX5100
337	TSV175
338	DMU
339	3780
340	BM70
341	8u
342	Date: %[02d]{day}/%[02d]{month}/%[04d]{year} Time: %[02d]{hours}:%[02d]{mins}:%[02d]{secs}
343	Self Test Completed Successfully!
344	Performing Reset for Latched Alarms
345	Firmware Revision: %[2d]{msb}.%[02d]{lsb}
346	Hardware Revision: %[2d]{msb}.%[02d]{lsb}
347	Setting fld dev output to 4mA. Proceed?
348	PV %{0} %{1} AO %{2} mA
349	Reset the Latched Alarms
350	Processing Calibration Log...
351	Exiting, device is busy.
352	%{1} Date: %[02d]{2}-%{3}-%[02d]{4} Time: %[02d]{5}:%[02d]{6}:%[02d]{7} Zero: %[4.2f]{8} Span: %[4.2f]{9}
353	first;previous;next;End
354	Calibration Log Calcode:%{1} Timestamp:%{2}
355	%{1} Date: %[02d]{2}-%{3}-%[02d]{4} Time: %[02d]{5}:%[02d]{6}:%[02d]{7}
356	Input Password
357	Input Choice
358	Disable;Enable;Change Password;End
359	Input New Password
360	Changing Write Protect/Password State
361	Detector Electronics Corp. UD10 Build Version: 01.27 Build Date: 12-Mar-2009
引用ID	字符串