| 0 |
G3-LEFM |
| 1 |
Cameron |
| 2 |
Meter status |
| 3 |
Oscillator alarm |
| 4 |
VOS alarmt |
| 5 |
Path alert |
| 6 |
Path fail |
| 7 |
CFG modified |
| 8 |
Flatness ratio |
| 9 |
Swirl |
| 10 |
Plane balance |
| 11 |
Assymetry Ratio |
| 12 |
Meter body temp OoR |
| 13 |
Fluid temp OoR |
| 14 |
Fluid pressure OoR |
| 15 |
Fluid density OoR |
| 16 |
Fluid viscosity OoR |
| 17 |
|
| 18 |
Off |
| 19 |
pv PDQ |
| 20 |
PV LS |
| 21 |
PV Fmly stat |
| 22 |
AN CH |
| 23 |
Number of analogue channels |
| 24 |
One Analog Ch |
| 25 |
One Out Channel. |
| 26 |
Three byte serial number |
| 27 |
PDQ |
| 28 |
Device Family Status |
| 29 |
More Device Family Status Available |
| 30 |
PV Var Class |
| 31 |
not classified |
| 32 |
SV Var Class |
| 33 |
TV Var Class |
| 34 |
FV Var Class |
| 35 |
PV fmly |
| 36 |
SV fmly |
| 37 |
TV fmly |
| 38 |
FV fmly |
| 39 |
.1f |
| 40 |
8.1f |
| 41 |
Density |
| 42 |
Viscosity |
| 43 |
Temperature |
| 44 |
Count factor |
| 45 |
Avg sound velocity |
| 46 |
Pressure |
| 47 |
Volume flow |
| 48 |
Volume flow Unit |
| 49 |
CFS |
| 50 |
CFM |
| 51 |
CMS |
| 52 |
CFH |
| 53 |
CMH |
| 54 |
BPH |
| 55 |
Density - Hardware that measures the density. |
| 56 |
Density Units |
| 57 |
g/cc |
| 58 |
gram per cubic cm |
| 59 |
API/deg |
| 60 |
Degrees API |
| 61 |
Lb/cf |
| 62 |
Pounds per cubic feet |
| 63 |
Viscosity - Hardware that measure the Viscosity. |
| 64 |
Viscosity Unit |
| 65 |
cSt |
| 66 |
Totalizer |
| 67 |
Temperature- Hardware that measures temperature. |
| 68 |
Unit |
| 69 |
degC |
| 70 |
degF |
| 71 |
count factor- Hardware that measures count_factor. |
| 72 |
Count Factor |
| 73 |
Avg sound velocity- Hardware that measures average_sound_velocity. |
| 74 |
Avg Sound Velocity |
| 75 |
m/s |
| 76 |
ft/s |
| 77 |
in/s |
| 78 |
pressure- Hardware that measures pressure. |
| 79 |
psiG |
| 80 |
kg/cm2 |
| 81 |
Bar |
| 82 |
kPaG |
| 83 |
MPaG |
| 84 |
normal |
| 85 |
4mA |
| 86 |
20mA |
| 87 |
Loop Current |
| 88 |
Configuration |
| 89 |
Offline Configuration |
| 90 |
Measurements |
| 91 |
Diagnostics |
| 92 |
Maintenance |
| 93 |
Device |
| 94 |
Service_menu |
| 95 |
Device Status |
| 96 |
Installation data |
| 97 |
PV Analog Channel Saturated |
| 98 |
PV Analog Channel Fixed |
| 99 |
Wireless |
| 100 |
WirelessHART Device |
| 101 |
IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation |
| 102 |
Primary |
| 103 |
Primary Analog Channel |
| 104 |
Secondary |
| 105 |
Secondary Analog Channel |
| 106 |
Tertiary |
| 107 |
Tertiary Analog Channel |
| 108 |
Quaternary |
| 109 |
Quaternary Analog Channel |
| 110 |
Quinary |
| 111 |
Quinary Analog Channel |
| 112 |
Critical Power Failure |
| 113 |
Lock all |
| 114 |
Trim not supported |
| 115 |
Configuration cannot be changed |
| 116 |
Locked by gateway |
| 117 |
Analog Input Channel |
| 118 |
Analog Output Channel |
| 119 |
Secondary Analog Channel Saturated |
| 120 |
Tertiary Analog Channel Saturated |
| 121 |
Quaternary Analog Channel Saturated |
| 122 |
Quinary Analog Channel Saturated |
| 123 |
Secondary Analog Channel Fixed |
| 124 |
Tertiary Analog Channel Fixed |
| 125 |
Quaternary Analog Channel Fixed |
| 126 |
Quinary Analog Channel Fixed |
| 127 |
Simulation active |
| 128 |
The device is in simulation mode and the level output is not representative of the process. |
| 129 |
Non-Volatile memory failure |
| 130 |
The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed. |
| 131 |
Volatile memory error |
| 132 |
The RAM memory check is invalid or maybe corrupt |
| 133 |
Watchdog reset executed |
| 134 |
A watchdog reset has been performed |
| 135 |
Voltage conditions out of range |
| 136 |
A voltage condition is outside its allowable range |
| 137 |
Environmental conditions out of range |
| 138 |
An internal or environmental condition is beyond acceptable limits. |
| 139 |
Electronic failure |
| 140 |
A hardware problem not related to the sensor has been detected. |
| 141 |
Subdevice list changed |
| 142 |
Duplicate master detected |
| 143 |
Capacity Denied |
| 144 |
The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified |
| 145 |
Bandwidth allocation pending |
| 146 |
Block transfer pending |
| 147 |
Battery life |
| 148 |
Percent range |
| 149 |
Loop current |
| 150 |
Primary variable |
| 151 |
Secondary variable |
| 152 |
Tertiary variable |
| 153 |
Quaternary variable |
| 154 |
Read receive time |
| 155 |
Write date and time |
| 156 |
Non-Volatile Clock |
| 157 |
When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure. |
| 158 |
Clock Uninitialized |
| 159 |
The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device. |
| 160 |
None |
| 161 |
No restrictions |
| 162 |
SI Only |
| 163 |
Restricted to SI Unit codes only |
| 164 |
Process automation device |
| 165 |
Discrete device |
| 166 |
Hybrid:Process automation+discrete |
| 167 |
I/O System |
| 168 |
WirelessHART Process automation device |
| 169 |
WirelessHART Discrete device |
| 170 |
WirelessHART Process automation+discrete |
| 171 |
WirelessHART Gateway |
| 172 |
WirelessHART Access point |
| 173 |
WirelessHART Process adapter |
| 174 |
WirelessHART Discrete adapter |
| 175 |
WirelessHART enabled handheld/portable maintenance tool |
| 176 |
Device Profile |
| 177 |
|
| 178 |
US |
| 179 |
United States of America |
| 180 |
JP |
| 181 |
Japan |
| 182 |
DE |
| 183 |
Germany |
| 184 |
FR |
| 185 |
France |
| 186 |
ES |
| 187 |
Spain |
| 188 |
RU |
| 189 |
Russian Federation |
| 190 |
CN |
| 191 |
People's Republic of China |
| 192 |
Secondary Master |
| 193 |
Primary Master |
| 194 |
Device Diagnostic Status 0 |
| 195 |
Device Diagnostic Status 1 |
| 196 |
I/O and Subdevice Status |
| 197 |
WirelessHART Status |
| 198 |
Time Set Option |
| 199 |
Real Time Clock Flags |
| 200 |
Country |
| 201 |
Country of intended device installation |
| 202 |
SI Unit Control |
| 203 |
Indicates if device should only display SI unit codes |
| 204 |
Time Stamp |
| 205 |
Relative time value on network |
| 206 |
8u |
| 207 |
Dynamic Variables Returned for Device Variables |
| 208 |
Command Response Truncated |
| 209 |
Configuration Change Counter Mismatch |
| 210 |
Status bytes mismatch |
| 211 |
8.3f |
| 212 |
.3f |