Device dictionary

Loading…

Reference ID	String
0	TRI-20
1	Shows the last-annunciated alarm
2	Alrm:
3	None
4	Diagnostic
5	Diagnostic Alarm
6	DBase Init
7	Database Initialization
8	Power Fail
9	Power Failure
10	Int Temp
11	Internal Puck Temperature
12	RTD
13	Flow
14	Pulse O/P
15	Pls Over
16	Pulse Output Overrun
17	Pls Secur
18	Pulse Security
19	Meter Fact
20	Linear
21	Linearization Alarm
22	Obsvd Temp
23	Observed Temperature Alarm
24	VCF Density
25	VCF Temp
26	Unknown
27	Tracking
28	The Analog Output is tracking the process normally
29	Upscale
30	The Analog Output is forced to maximum
31	Downscale
32	The Analog Output is forces to minimum
33	Hold Last
34	The Analog Output is holding last output value
35	4.1f
36	If CTL-method is chosen to be 'API', then this selects the specific API table# e.g. 6B
37	API Table
38	5A
39	5B
40	5D
41	6A
42	6B
43	6C
44	6D
45	23A
46	23B
47	23D
48	24A
49	24B
50	24C
51	24D
52	53A
53	53B
54	54A
55	54B
56	54C
57	54D
58	Historical 5
59	Historical 6
60	Historical 23
61	Historical 24
62	Historical 53
63	Historical 54
64	Selects the Function of the Contact Output from a list of choices
65	Function
66	No manually driven output
67	Reverse
68	Reverse flow indication
69	Alarm O/P
70	Alarm contact ouput gate
71	MM O/P Gate
72	Master Meter Output Gate
73	Selects the Polarity of the Contact Output, N.O. or N.C.
74	Polarity
75	N/O
76	Normally Open
77	N/C
78	Normally Closed
79	Displays the active/inactive state of the Contact Output
80	State
81	Off
82	Not On
83	On
84	Not Off
85	Contact State
86	Factor for Correction for the Pressure of the Liquid
87	Cpl
88	8.6f
89	Slope of the Line that relates CPL to Observed Pressure
90	Alpha
91	9.7f
92	Selects a technique for Pressure Compensation
93	Method
94	User
95	User Entered CPL
96	CPL Linear
97	CPL Linear Equation
98	API 11.2.1
99	API 11.2.2
100	Factor for Correction for the Temperature of the Liquid
101	Ctl
102	Slope of the Line that relates CTL to Observed Temperature
103	Selects a technique for Temperature Compensation
104	User Entered CTL
105	CTL Linear
106	CTL Linear Equation
107	Selects the place(s) where the alarm will be annunciated
108	Dest
109	No Alarm Destination
110	Contact O/P
111	Contact Output
112	LOI
113	Local Operator Interface
114	Both
115	Both Contact Output and Local Operator Interface
116	Enables or Disables this Alarm
117	Enable
118	Disabled
119	Enabled
120	Selects if this Alarm is Latching or Not
121	Type
122	Non Latching
123	Latching
124	Units of Measure for Density parameters
125	Diagnostic Code
126	Diag Code
127	Equilibrium Pressure Source
128	Equ Press Src
129	Absolute
130	User entered absolute
131	Gauge
132	User entered gauge
133	GPA-TP15
134	Calculated from GPA-TP15
135	Equilibrium Vapor Pressure
136	Equilbrm
137	6.1f
138	Factory Calibration Factor
139	FCF01
140	7.5f
141	FCF10
142	FCF02
143	FCF03
144	FCF04
145	FCF05
146	FCF06
147	FCF07
148	FCF08
149	FCF09
150	Factory Calibration Factor Flow Rate
151	FFlow 1
152	9.2f
153	FFlow 10
154	FFlow 2
155	FFlow 3
156	FFlow 4
157	FFlow 5
158	FFlow 6
159	FFlow 7
160	FFlow 8
161	FFlow 9
162	Units of Measure for the Factory Calibration Factor FlowRates
163	L/d
164	Liters per Day
165	g/d
166	Grams per Day
167	Tons/sec
168	Tons per Second
169	MTon/sec
170	Metric Tons per Second
171	Documents the material code for the flanges, end-fittings
172	Flange Matl
173	Hastelloy B2
174	Documents the type of flanges, end-fittings
175	Flange Type
176	NPT_Threads
177	MS_Tubing
178	ANSI_150#RF
179	ANSI_300#RF
180	ANSI_400#RF
181	ANSI_600#RF
182	ANSI_900#RF
183	DIN_PN10
184	DIN_PN15
185	DIN_PN25
186	DIN_PN40
187	DIN_PN50
188	DIN_PN64
189	DIN_PN80
190	DIN_PN100
191	DIN_SPUD
192	TRI_CLOVER
193	JIS_10K_RF
194	JIS_16K_RF
195	High Limit
196	Hi
197	Low Limit
198	Lo
199	Time Period over which flow exceeds limits before an alarm is generated
200	Time
201	Selects if Observed Density was measured using a Glass Hydrometer
202	Glass Hydro
203	Gross Inventory Totalizer
204	Grs
205	8.0f
206	8.1f
207	8.2f
208	8.3f
209	8.4f
210	8.5f
211	8.7f
212	Gross Resettable Totalizer
213	Selects whether the pulse-input(s) wired to the SMM are a single-phase pulse (ignore the second phase), a dual-phase bidirectional-type, etc.
214	I/P Func
215	Single Phase
216	Dual Ph. Uni-Dir
217	Dual Phase Unidirectional
218	Dual Ph. Bi-Dir
219	Dual Phase Bidirectional
220	Dual Ph. Coinc.
221	Dual Phase Coincident
222	Internal temperature of the transmitter electronics
223	Inventory Totalizers' Number of Digits and Decimal Digits to Display
224	Dec Digits
225	99999999.
226	9999999.9
227	999999.99
228	99999.999
229	9999.9999
230	999.99999
231	99.999999
232	9.9999999
233	K-factor. Relates number of input pulses to flow quantity
234	K-Fact
235	9.4f
236	Selects the units-of-measure for the K-factor
237	Dl
238	DecaLiters
239	ml
240	MilliLiters
241	cu cm
242	Cubic Centimeters
243	Local Power Supply is Present
244	Power
245	Local Operator Interface is Present
246	Loop Current
247	The raw incoming pulse frequency below which the meter is deemed to not be rotating (flow = 0.00)
248	Cutoff
249	6.4f
250	Units of Measure for Mass Flow Rate
251	Mass
252	MetTons/sec
253	Mass Inventory Totalizer
254	Mas
255	Units of Measure for Mass Inventory Totalizers
256	Mass Unit
257	Mass Resettable Totalizer
258	Units of Measure for Mass Resettable Totalizers
259	Meter Factor, at each of several flow rates
260	MF01
261	MF10
262	MF02
263	MF03
264	MF04
265	MF05
266	MF06
267	MF07
268	MF08
269	MF09
270	Documents the Meter Flow High Limit
271	Flow Hi
272	Documents the Meter Flow Low Limit
273	Flow Lo
274	Shows the pulser input frequency
275	Meter Freq
276	7.1f
277	Documents the Material Composition of the Meter Body
278	Meter Matl
279	Documents the Meter Pressure Drop Limit
280	Drop Lim
281	Documents the Meter Pressure High Limi
282	Press Hi
283	Documents the Meter Pressure Low Limit
284	Press Lo
285	Documents the Meter Temperature High Limit
286	Temp Hi
287	Documents the Meter Temperature Low Limit
288	Temp Lo
289	Meter Factor Deviation Alarm Level, in Percent
290	Alarm Pct
291	5.3f
292	Flow Rate for each defined Meter Factor
293	Flow 1
294	Flow 10
295	Flow 2
296	Flow 3
297	Flow 4
298	Flow 5
299	Flow 6
300	Flow 7
301	Flow 8
302	Flow 9
303	Units of Measure for the Meter Factor FlowRates
304	MFFR Unit
305	Documents the Model Code for this Meter
306	Model
307	Net Inventory Totalizer
308	Net
309	Net Resettable Totalizer
310	Enables the use of a Non-Standard Reference Temperature (e.g. other than 15C or 60F)
311	NSTR
312	Observed Density. Normally Calculated from Reference Density and VCF, but User-Entered only when using 'odd' API Tables
313	Obsvd
314	5.4f
315	5.1f
316	Observed Temperature in the process
317	Observed Pressure. User-Entered.
318	Observed Pressure Source
319	Obs Press Src
320	User Entered Absolute
321	User Entered Gauge
322	Delta Equilibrium
323	User Entered Delta above Equilibrium Pressure
324	Time Period over which temperature exceeds limits before an alarm is generated
325	LOI Operator-Mode Timeout Period
326	OM Timeout
327	Units of Measure for Pressure parameters
328	Shows whether the Local-Operator-Interface is in Program mode or Operator mode
329	Prog Mode
330	LOI Program-Mode Timeout-Period
331	PM Timeout
332	Documents the Signal level of the Pulse Input
333	Reluctance
334	Weigand
335	Amorphous
336	Contact Closure
337	Logic Level
338	Documents the presence of a Pulse Output Connector
339	Pls O/P Conn
340	Duration
341	Pulse O/P Freq
342	Adjusts the number of Output Pulses per Unit of Flow
343	Scaler
344	10.4f
345	Selects the Flow parameter that is used to create Output Pulses
346	Source
347	Raw Pulses
348	Raw Meter Pulses
349	Linearized
350	Linearized Meter Pulses
351	Temp. Comp.
352	Temperature Compensated Pulses
353	Temp Comp Lin
354	Temperature Compensated, Linearized Pulses
355	Gross Vol
356	Gross Volume
357	Net Vol
358	Net Volume
359	Selects the unit-of-flow that will generate one output pulse. Scaler can then be used to generate more or fewer
360	Sets the on-time width of Output Pulses. Off-time varies with the Output Frequency
361	Width
362	Pulse-Security Error Count
363	Err Count
364	5i
365	Pulse-Security Sample Count
366	Samp Count
367	Selects a parameter for Quick View display
368	Gross Flow
369	Net Flow
370	Mass Flow
371	Gross Flow Total
372	Net Flow Total
373	Mass Flow Total
374	Gr Fl Reset Total
375	Gross Flow Resettable Totalizer
376	Nt Fl Reset Total
377	Net Flow Resettable Totalizer
378	Mass Fl Reset Total
379	Mass Flow Resettable Totalizer
380	Observed Temp
381	Alarm Status
382	AO Perecent
383	Length of time in seconds that QuickView data is shown on the display
384	Data
385	A descriptive name for a Quick View display
386	Descrptn
387	Length of time in seconds that QuickView description is shown on the display
388	Length of time in seconds that QuickView unit-of-measure is shown on the display
389	Reset Permissive. Enables the Reset button from a Quick View display
390	Reset
391	Reference Density. Normally a User-Entry to describe the Fluid's Physical Properties. Calculated from Observed Density and VCF only when using 'odd' API Tables
392	Refer
393	Reference Temperature. Normally 15C or 60F
394	Ref Temp
395	Resettable Totalizers' Number of Digits and Decimal Digits to Display
396	Reverse Gross Inventory Totalizer
397	Gross
398	Reverse Gross Resettable Totalizer
399	Reverse Mass Inventory Totalizer
400	Reverse Mass Resettable Totalizer
401	Reverse Net Inventory Totalizer
402	Reverse Net Resettable Totalizer
403	A measure of curvature of the RTD's ohms vs. temperature curve. See the RTD Mfgr's data
404	See the RTD Mfgr's data
405	Delta
406	An Ohms reading to subtract from the RTD probe, to allow for unbalanced wiring resistance
407	Offset
408	5.2f
409	Shows the present reading of Ohms from the RTD probe
410	Ohms
411	6.2f
412	The ohms reading of the RTD at zero degrees C
413	R0
414	Documents the Serial Number of the RTD
415	Ser No
416	Selects the material composition and alpha of the RTD probe
417	Custom
418	PT100 00385
419	PT100 00392
420	PT100 SAMA
421	PT100 JISC
422	CU 100
423	NI 100
424	NI 120
425	KTY821 Thermistor
426	KTY822 Thermistor
427	8-digit password for use of the Local-Operator-Interface. * is a wild-card.
428	Password
429	Sequence Number, # of batches run, # of times resettable totalizers were re-initialized
430	Seq No
431	8i
432	Documents the Serial Number for Meter
433	Software Revision
434	Sftwr Rev
435	Units of Measure for Temperature parameters
436	Volume Correction Factor, relates Gross Volume vs. Net (at reference conditions). VCF = CTL x CPL
437	Vcf
438	Units of Measure for Volumetric Flow Rates
439	Volume
440	l/d
441	Units of Measure for Volume Inventory Totalizers
442	Vol Unit
443	Deka-Liters
444	Milli-Liters
445	cu.cm.
446	Units of Measure for Volume Resettable Totalizers
447	Weighted Average Observed Density during this batch
448	Wavg Odens
449	Weighted Average Observed Pressure during this batch
450	Wavg Press
451	Weighted Average Observed Temperature during this batch
452	Wavg Temp
453	Weighted Average Reference Density during this batch
454	Wavg Rdens
455	Counts changes to Weights&Measures protected Calibration parameters
456	Calib
457	6i
458	Counts changes to Weights&Measures protected Configuration parameters
459	Config
460	Selects if Density is a Weights and Measures protected parameter
461	Dens Prot
462	Remote Security Lock
463	Lock
464	Accessories
465	Alarm Config
466	Alarms
467	Analog Output
468	Basic Setup
469	Computations
470	Corrections
471	Dbase Init
472	Detailed Setup
473	Density
474	Device Info
475	Diagnostics
476	Diags & Services
477	Flow Meter
478	Flow Rate
479	Flow Rate Units
480	HART Output
481	Internal Temp
482	Inventory
483	Inv Totals
484	Linearization
485	Local Display
486	Loop Test
487	Measurements
488	Meter Calibration
489	Meter Config
490	MFactor Deviation
491	Meter Factors
492	Obsrvd Temp
493	Outputs
494	Press Correction
495	Pressure
496	Process Variables
497	Pulse I/P Sec
498	Pulse Out Config
499	Pulse Out Overrun
500	Pulse O/P 1
501	Pulse O/P 2
502	Pulser
503	Quick Views
504	QV Timers
505	QV PV Timers
506	QV Screen 1
507	QV Screen 2
508	QV Screen 3
509	QV Screen 4
510	QV Screen 5
511	QV Screen 6
512	QV Screen 7
513	QV Screen 8
514	Resettable
515	Totalizers
516	Revision Info
517	Root Menu
518	RTD Probe
519	RTD Setup
520	Status
521	Temp Correction
522	Temperature
523	Temp Sensor
524	Test Device
525	Vol Corr Density
526	Vol Corr Temp
527	W & M
528	Weighted Avgs
529	Loop Notice
530	Notify the operator that the control loop should be returned to automatic
531	Dynamic Edit Notice
532	This value may be being dynamically calculated. Consult Help or Instr.Manual to verify that this edit value will not be automatically overwritten
533	Contact O/P Test
534	Toggle the Contact Output off and on
535	Edit Warning
536	Warn the operator that changing this parameter will dramatically affect how other parameters are calculated
537	Puts the Analog Out in manual control. Allows the operator to set the Analog Out value to 4 mA, 20 mA, or return to automatic control.
538	Mass Flow Units Warn
539	Warning message when Mass Flow Units are edited
540	Not Available
541	This feature is not available at this time
542	Pulse Out Abort
543	Cease testing the Pulse Output
544	Pulse O/P Test
545	Manually set the Pulse Output frequencey and the duration of the test. Duration is in seconds. A value of 0 sets the Pulse Output to run continuously
546	Reset Alarm
547	Acknowledges and clears the topmost Alarm
548	Clears all of the resettable totalizers to zero, prepares for the next batch
549	Temperature Units Edit Warn
550	Warning message when Temperature Units are changed
551	Variable mapping
552	Variable mapping - Display information as to how the device variables are mapped into PV, SV, TV and QV
553	Variable Re-Map
554	Variable re-mapping - Re-map the device variables into PV, SV, TV and QV
555	Volumetric Flow Edit Warn
556	Warning message when Volumentric Units are edited
557	Parameter Limits Exceeded
558	The value of some of the parameter(s) written exceeded the Min or Max limit of the parameter
559	Alarm Status 2
560	Error detected from meter pulser
561	Meter Factor
562	Meter Factor Deviation outside spcified limits
563	Meter Factor Calibration Table values and/or configuration is invalid
564	Process Temperature has exceeded defined limits
565	Vol Corr Dens
566	Density out of range for selected API Table
567	Temperature out of range for selected API Table
568	Alarm Status 1
569	Device Diagnostics detected a problem, see Diagnostic Status for more information
570	Database Init
571	The field device internal database has been initialized to default values
572	A power failure has occured
573	The internal temperature of the device has exceeded maximum limits
574	RTD has failed or not connected
575	The flow rate has exceeded device limits
576	The pulse output configuration parameters are in error or confilict
577	The process flow rate has excceded the configured pulse output parameters
578	Diagnostic Status
579	RAM Test Fail
580	Field Deivce RAM Memory failed self-test
581	Flash Test Fail
582	Field Device Flash Memory failed sefl-test
583	Dbase Chksum Err
584	Field Device Database failed checksum test
585	PIC Reset
586	Pulse processor has reset
587	PIC Fail
588	Pulse processor has failed
589	ADC Fail
590	A/D Converter is not responiding
591	Int Temp Sensor
592	The Field Device Internal Temperature Sensor has failed
593	Turns on or off warning messages associated with editing some variables. Does not turn off the Loop Warning message
594	Warning Level
595	Process Temp
596	Device Setup
597	write_variables
598	FMU860
599	DT
600	DVC
601	FCX
602	AS800
603	340T
604	340C
605	344
606	Siemens Micro K
607	SITRANS L
608	SIPAN PH
609	SITRANS P
610	75SMT
611	UNIDELTA
612	8320
613	SX5100
614	TSV175
615	DMU
616	3780
617	BM70
618	8u
619	-WARNING- Return control loop to automatic control
620	NOTE: This value may be dynamically calculated. Consult Help for this var. for addl. info
621	Set Contact O/P State:
622	Off;On;Auto Control;Exit
623	Contact Ouptut is now Off
624	Contact Output is now On
625	Contact Output is now in Automatic Control
626	Contact Output returned to Automatic Control
627	WARNING: This parameter change will affect transmitter calculations in a significant way.
628	Set Loop Current
629	4 mA;20 mA;Auto Control
630	-WARNING- Pressing 'OK' will change device output. and place the loop in manual.
631	Loop returned to Automatic Control
632	Loop in Manual Control and fixed to selected value
633	WARNING: This parameter change will affect device output. Place the loop in manual.
634	Pulse O/P Test aborted
635	Select O/P Channel
636	1;2
637	Enter Frequency:
638	frequency
639	Value must be between 1.0 and 1000.0 Hz
640	Enter Pulse Count: (0 = Continuous)
641	duration
642	Test will run Continuously
643	Test will run approximately %[8.3f]{RunTime} secs.
644	Sending Continuous Pulses...
645	Running Test....
646	Test Complete
647	Continue;Exit
648	There are no Alarms to clear
649	Resetting Diagnostic Alarm will clear Diagnostic Status Bits
650	Press OK to clear %{0} Alarm
651	Are You Sure?
652	Yes;No
653	Variable mapping: PV is %{0} SV is %{1} TV is %{2} QV is %{3}
654	-WARNING- Pressing 'OK' will change device output. Put loop in manual.
655	Select PV
656	Gross Flow;Net Flow;Mass Flow;Process Temp
Reference ID	String