HART设备字典

Loading…

引用ID	字符串
0	MAGNEW2W
1	Azbil Corporation
2	3.1f
3	In Status group1, show the status for Nonvolatile memory and CPU. If the status is ON, the device may be damaged. Restore power supply or contact representative of Azbil Corporation.
4	B/O simulation
5	NVM FAULT
6	CPU FAULT
7	HI<LO: High limit alarm value < Low limit alarm value. Set alarm value as Hi > Lo. Span over: Check the detector size. Set the span as the flow velocity becomes 10m/s or less. Pulse scale: Correct pulse scale. Set the pulse scale as the span frequency becomes between 0.0001Hz and 200Hz. If engineering unit of span is volumetric, apply the volumetric unit to the pulse scale. If engineering unit of span is mass, apply the mass unit to the pulse scale. Pulse width: Set the correct pulse width to become duty 70% or less. Or set duty 50% as pulse width.
8	IN LOCAL MODE
9	DO OUTPUT MODE
10	PLS OUTPUT MODE
11	AO OUTPUT MODE
12	IN CALIB MODE
13	NOT CALIBRATED
14	EX OUTPUT MODE
15	In Status group2, show the status of loop test and calibration.
16	EMPTY OR SCALE ERROR
17	IN OUTPUT CHECK MODE w/CALIB
18	HI<LO ALM ERROR
19	SPAN OVER ERROR
20	PLS SCALE ERROR
21	PLS WIDTH ERROR
22	Pulse error; See status group 3
23	Flow Sensor- Hardware that measures flow rate.
24	Pulse output- scaled frequency output from 0-1000 Hz, linear with input.
25	Gross Total- Non-resettable totalizer.
26	Net Total Value- Resettable totalizer.
27	Reverse Total- Non-resettable reverse totalizer.
28	write variables
29	Gross Total- Non-resettable totalizer
30	Net Total Value- Resettable totalizer
31	Reverse Total - Non-resettable reverse totalizer
32	Auto zero trim
33	Auto zero trim-Calibration for zero point.
34	AO
35	.1f
36	5.1f
37	.5f
38	.4f
39	6.4f
40	Puls out unit
41	m3/P
42	l/P
43	cm3/P
44	t/P
45	kg/P
46	g/P
47	B/P
48	kG/P
49	G/P
50	mG/P
51	IG/P
52	KIG/P
53	mIG/P
54	lb/P
55	Pulse Width
56	ms
57	4d
58	Lo flo cutoff-Adjustable from 1 to 10% of the setting range. Below set value, output is driven to the zero flow rate signal level. Display is latched to zero.
59	0 %
60	1 %
61	2 %
62	3 %
63	4 %
64	5 %
65	6 %
66	7 %
67	8 %
68	9 %
69	10 %
70	Tube size
71	Flow tube size- Nominal inside diameter of the pipe adjacent to the sensor.
72	2.5 A
73	5 A
74	10 A
75	15 A
76	20 A
77	25 A
78	32 A
79	40 A
80	50 A
81	65 A
82	80 A
83	100 A
84	125 A
85	150 A
86	200 A
87	250 A
88	300 A
89	350 A
90	400 A
91	450 A
92	500 A
93	600 A
94	700 A
95	800 A
96	900 A
97	1000 A
98	1100 A
99	Puls outp test
100	Pulse Output Test Value- Scaled frequency output from 0-1000 Hz, linear with input.
101	%
102	Totalizer Control Code- Controls the operation of all available totalizers.
103	10d
104	Totalizer display-Display totalized value.
105	8d
106	Gravity
107	Specific gravity
108	Disp select
109	Set main display. %: Percent of range. Rate: Flow rate. Total: Totalized value.
110	Rate
111	Total
112	Func set
113	Select Pulse or DO output. Pulse: Pulse output. ST out: Digital status output.
114	Pulse
115	Hi Lo ST out
116	Electrode ST out
117	EX value
118	EX value: Unique detector factor.Ex factor is stamped on the name plate.
119	Coefficient
120	Set coefficient. Outputs are calculated by multiplying set coefficient. Default value is 1.0000.
121	Detector type
122	Detector type-Detector type. Set MTG.
123	MTG
124	TST
125	SMT
126	Burn out AO
127	Burn out AO-set burn out high, low or hold.
128	High
129	Low
130	Hold
131	Burn out Pls
132	Burn out Pls-set burn out off or hold.
133	Off
134	Burn out DO
135	Burn out DO-set burn out open or close.
136	Close
137	Open
138	Drop out
139	Drop out-Adjustable from 1 to 10% of the setting range. Below the set value, pulse output is cut.
140	Pls width flag
141	On to 50%, Off to 1ms between 1000ms
142	50 %
143	On
144	Total restart val
145	Total restart val-Restart value of totalizer.
146	Total prev val
147	Hi alarm
148	Hi alarm-Set the upper limit value in percent of range.
149	.0f
150	3.0f
151	Low alarm
152	Low alarm-Set the lower limit value in percent of range.
153	Auto spike cut
154	Auto spike cut-Software signal processing against spike noise.
155	Off
156	On
157	Moving average
158	Moving average-Software signal processing. Apply moving average to output.
159	Mvng av time
160	s
161	Mvng av time-Moving average time.
162	4.1f
163	Pls calib
164	5d
165	PLS output kind
166	Up
167	Down
168	EX current FRQ
169	Hz
170	12.5
171	15.0
172	17.5
173	22.5
174	25.0
175	27.5
176	30.0
177	5.0
178	EX current CHG
179	MODE 0
180	MODE 1
181	MODE 2
182	MODE 3
183	MODE 4
184	MODE 5
185	MODE 6
186	MODE 7
187	MODE 8
188	MODE 9
189	MODE A
190	SI or ALL
191	ALL
192	SI
193	Auto zero range
194	0.2 m/s
195	Release
196	EX value range
197	200-700
198	EX CURR 3.5mA
199	EX Current
200	mV
201	7.4f
202	Low flow supprs
203	Pulse coef value
204	COMM mode
205	HART
206	SFN.A
207	SFN.D
208	NONE
209	DE word length
210	4
211	6
212	Burn out SIM
213	Memory address
214	04X
215	08X
216	06X
217	I.OUT AO %
218	3d
219	P.OUT PLS %
220	EX out check
221	EX0
222	EX1
223	EX2
224	EX3
225	EX4
226	STOUT check
227	Done
228	In progress
229	Error
230	Flow direction
231	Forward
232	Reverse
233	Type SMT
234	On
235	Device free condition
236	Free
237	Write protected
238	Device busy
239	Check report
240	Check OK
241	Auto zero error
242	Gain trim error
243	Auto zero and Gain trim error
244	ID check report
245	ID not defined
246	ID passd check
247	Bilingal
248	Low flow cut flag
249	Zero comp
250	Detect fluctu
251	Tow few low limit data
252	Too much low limit data
253	Tow few High limit data
254	Too much High limit data
255	Low > High data
256	Too few coefficent
257	Too much coefficient
258	Too few gravity
259	Too much gravity
260	Burn out (4mA-20mA) data
261	Burn out (PULSE) data
262	Normal contact data
263	Too few averaging time
264	Too much averaging time
265	Device is busy
266	Pulse output is not available. Set pulse in function set in Basic Setup menu.
267	DO is not available. Set DO in function set in Basic setup menu.
268	Too few pulse coefficient
269	Too much pulse coefficient
270	Too few value
271	Too much value
272	Device Status
273	Loop test
274	Calibration
275	EX current trim
276	Factory use
277	Factory use: EX
278	Factory use: FLAGS
279	Memory store
280	Detector config
281	Conf outputs
282	Analog output
283	Pulse output
284	Totalizer
285	Digital output
286	Hart output
287	Noise immunity
288	Device info
289	Revision No.
290	Reset totalizer
291	Reset totalizer-Replace the totalized value with the set value of the Total restart val.
292	D/A trim
293	D/A trim-Calibration for analog output
294	EX D/A value
295	Abort EX D/A value
296	Shipping save
297	Shipping RCVR
298	Shipping data recovery-All data are set as factory default values.
299	Initial RCVR
300	Gain trim
301	Gain trim-Electrical trim.
302	I.OUT D/A value
303	Abort I.OUT D/A value
304	Output check AO
305	Output check of analog current
306	Abort Output check AO
307	Output check Pls
308	Output check of pulse output
309	Abort Output check Pls
310	Output check EX
311	Output check of excitation current
312	Abort Output check EX
313	Output check DO
314	Output check of digital status output
315	Abort Output check DO
316	Pulse trim
317	Pulse trim-Calibration for pulse output.
318	Abort Pulse trim
319	EX current trim-Calibration for excitation current.
320	Abort EX current trim
321	Pulse coeff
322	Abort pulse coeff out
323	Pulse width
324	Abort pulse width
325	COMM output
326	Select communication protocol.
327	Memory operate
328	Abort memory operation
329	Set DEVICE-ID
330	Abort DEVICE-ID
331	EX value-Unique detector factor.Ex factor is stamped on the name plate.
332	NVM Write on
333	Electrode status sensitivity
334	Setup electrode status sensitivity level
335	OFF
336	HIGH
337	MID
338	LOW
339	LL
340	LLL
341	Electrode status output mode
342	Setup output mode, when electrode status up
343	ZERO
344	HOLD
345	Loop check control code
346	Control loop check mode w/calibrator
347	Ready
348	Quit
349	Loop check mode
350	Loop check mode w/calibrator
351	Abort loop check mode
352	Manual zero control code
353	Control manual zero
354	Up
355	Manual zero
356	Manual zero 1 trim
357	Manual zero 1 trim-Calibration for zero point.
358	Manual zero 2 trim
359	Manual zero 2 trim-Calibration for zero point.
360	Manual zero 3 trim
361	Manual zero 3 trim-Calibration for zero point.
362	Abort manual zero mode
363	C2 value R/W
364	Detect factor 7mA value.
365	Too few coefficient
366	DF 4.9mA value R/W
367	Detect factor 4.9mA value.
368	Span1 value (float)
369	Span1 value (float).
370	Span1 value (BCD)
371	Span1 value (BCD).
372	Span1 value (BCD) R/W
373	Read/Write span1 value w/BCD.
374	Error format
375	Pulse weight value (float)
376	Pulse weight value (float).
377	Pulse weight value (BCD)
378	Pulse weight value (BCD).
379	Pulse weight value (BCD) R/W
380	Read/Write pulse weight value w/BCD.
381	EX local conf value
382	DISABLE
383	ENABLE
384	m3/d
385	m3/h
386	m3/m
387	m3/s
388	l/d
389	l/h
390	l/m
391	l/s
392	cm3/d
393	cm3/h
394	cm3/m
395	cm3/s
396	t/d
397	t/h
398	t/m
399	t/s
400	kg/d
401	kg/h
402	kg/m
403	kg/s
404	g/d
405	g/h
406	g/m
407	g/s
408	BPD
409	BPH
410	BPM
411	BPS
412	kGPD
413	kGPH
414	kGPM
415	kGPS
416	IGPD
417	IGPH
418	IGPM
419	IGPS
420	kIGPD
421	kIGPH
422	kIGPM
423	kIGPS
424	mIGPD
425	mIGPH
426	mIGPM
427	mIGPS
428	GPD
429	GPH
430	GPM
431	GPS
432	mGPD
433	mGPH
434	mGPM
435	mGPS
436	lb/d
437	lb/h
438	lb/m
439	lb/s
440	FMU860
441	DT
442	DVC
443	FCX
444	AS800
445	340T
446	340C
447	344
448	Siemens Micro K
449	SITRANS L
450	SIPAN PH
451	SITRANS P
452	75SMT
453	UNIDELTA
454	8320
455	SX5100
456	TSV175
457	DMU
458	3780
459	BM70
460	8u
461	Pulse Output Unit- Engineering units that the frequency andtotalizer outputs will be displayed with.
462	??
463	Pulse Scaling Factor- Magnitude of process variable per pulse.
464	7.5f
465	.2f
466	6.2f
467	4.2f
468	Puls outp
469	Pulse Output Value- scaled frequency output from 0-1000 Hz, linear with input.
470	Net Total Value- Resettable totalizer value. Counts frequency output pulses while total control is turned on.
471	Gross Total Value- Non-resettable totalizer value. Counts frequency output pulses while total control is turned on. This value will be reset to 0 when the pulse scaling, line size, or units are changed.
472	Reverse Total Value- Non-resettable totalizer value. Counts frequency output pulses while total control is turned on and flow is in the reverse direction. This value will be reset to 0 when the pulse scaling, line size, or units are changed.
473	7d
474	Coil Drive Frequency- Frequency that the coils operate at.
475	6Hz
476	30Hz
477	gross_total_units
478	Pulse output units- Engineering units that the frequency and totalizer outputs will be displayed with
479	Net Total Value- Counts frequency output pulses while total control is turned on.
480	Pulse Output- Scaled frequency output from 0-1000 Hz, linear with input.
481	Pulse output value- scaled frequency output from 0-1000 Hz, linear with input
482	Totalizer units
483	Gross Total Value- Counts frequency output pulses while total control is turned on. This value will be reset to 0 when the pulse scaling, line size , or units are changed
484	Reverse Total Value- Counts frequency output pulses while total control is turned on and flow is in the reverse direction. This value will be reset to 0 when the pulse scaling, line size, or units are changed
485	Totalizer Variable- Counts pulses from frequency output and scales the value based on the pulse output scaling and units.
486	About to enter auto zero
487	The previous error was seen while trying to initiate auto zero
488	Waiting for auto zero to complete.
489	Device failure. Device may be stuck in Auto Zero.
490	Device failure in Auto Zero.
491	The previous error was seen while trying to burn eeprom
492	Auto zero passed
493	Sensor
494	Sensor Config
495	Sensor Info
496	Device Info
497	Revision #'s
498	Totalizer will be reset
499	Yes;End
500	Totalizer was reset.
501	Choose D/A trim
502	4mA;20mA;End
503	Choose DAC trim func
504	Set;End
505	DAC trim 4mA End
506	DAC trim 20mA End
507	Choose EX value
508	3.5mA;4.9mA;7.0mA;11.9mA;14.0mA;End
509	Set another value
510	EX D/A value ABORTED!
511	Shippng data save Ready?
512	Saved
513	End
514	Device will be reboot, please connect again
515	Shippng data recovery Ready?
516	CAUTION: Shipping data recovery will be soon, DO NOT RETRY. Quit and re-connect 20 seconds later.
517	Initial data recovery Ready?
518	CAUTION: Initial data recovery will be soon, DO NOT RETRY. Quit and re-connect 20 seconds later.
519	Connect MagneW calibrator
520	Choose gain
521	0.0m/s; 2.5m/s;10.0m/s;End
522	Set 0.0m/s on MagneW calibrator, wait 120s
523	Start gain 0.0m/s
524	Set 2.5m/s on MagneW calibrator, wait 30s
525	Start gain 2.5m/s
526	Set 10.0m/s on MagneW calibrator, wait 30s
527	Start gain 10.0m/s
528	Waiting for gain 0.0m/s to complete.
529	Waiting for gain 2.5m/s to complete.
530	Waiting for gain 10.0m/s to complete.
531	Gain trim complete
532	Choose I.OUT Current
533	4mA;20mA;End
534	I.OUT D/A value ABORTED!
535	Choose output check analog current
536	Start;End
537	Output check AO ABORTED!
538	Choose output check pulse
539	Output check Pls ABORTED!
540	Choose output check excitation
541	Select another EX
542	Output check EX ABORTED!
543	Choose output check DO
544	Select another value
545	Output check DO ABORTED!
546	Setting fld dev 90Hz
547	Choose Pulse trim func
548	Set meter digit
549	Pulse trim ABORTED!
550	Choose EX current trim
551	3.5mA; 4.9mA; 7.0mA;11.9mA;14.0mA;End
552	Setting fld dev 3.5mA
553	Setting fld dev 4.9mA
554	Setting fld dev 7.0mA
555	Setting fld dev 11.9mA
556	Setting fld dev 14.0mA
557	Choose EX trim func
558	EX current trim ABORTED!
559	Pulse coeff out ABORTED!
560	Number to DUTY 50%
561	Yes;No;End
562	Input another value
563	DUTY 50% to Number
564	Pulse width ABORTED!
565	Protocol
566	HART;SFN analog;SFN digital;None;End
567	HART protocol
568	Yes;No
569	SFN analog protocol, device will be reboot
570	SFN digital protocol, device will be reboot
571	None protocol, device will be reboot
572	Set memory location
573	Set memory data
574	Set another EX value
575	Out of range error
576	NVM write on Ready?
577	CAUTION: DO NOT RETRY, Re-connect 20 seconds after
578	NVM write on
579	Choose loop check mode
580	Start;Abort
581	End;Abort
582	Loop check mode ABORTED!
583	Wait working time about 20sec.
584	Waiting.....(about 20sec).
585	Select menu (%[5.2f]{fval}%)
586	Up;Down;Refresh %;Quit(Manual zero end)
587	Manual zero mode ABORTED!
588	Set another C2 value
589	Set another DF 4.9mA value
590	Receive data format error.
591	Set another span1 value
592	Set another pulse weight value
593	Confirm flow rate is zero, wait 120s
594	Auto zero complete
引用ID	字符串