Device dictionary

Loading…

Reference ID	String
0	APT3200
1	Autrol(Duon)
2	Duon System
3	External EEPROM write fail
4	Flash Access violation
5	Flash memory write fail
6	Pressure PV Data Over limit
7	Pressure count Over limit
8	Sensor error
9	ADC Counter limit over
10	ADC setting value changed
11	ADC DRDY timeout
12	Oscillator Fault
13	Calibration data error
14	Thermometer error
15	External EEPROM read fail
16	Program memory CRC error
17	.3f
18	Pres Dev fmly
19	Pres Class
20	Pres PDQ
21	Pres LS
22	Pres Fmly stat
23	8.3f
24	Pressure Update Period
25
26	s
27	7d
28	Pres Lower trim
29	Pres Upper trim
30	Pres Trim support
31	Pres Min lower trim
32	Pres Max lower trim
33	Pres Min upper trim
34	Pres Max upper trim
35	Pres Min trim diff
36	Simulate
37	Update Period
38	Snsr temp unit
39	Sensor Temperature Units- Engineering unit to be displayed with Sensor Temperature.
40	Temp Class
41	Temp PDQ
42	Temp LS
43	Temp Dev Stat
44	Temp USL
45	Temp LSL
46	Temp min span
47	Temp Update Period
48	Temp snsr s/n
49	Secondary Variable - Temperature Compensation
50	Pressure
51	Temperature
52	Select trim mode
53	Trim Mode
54	Point
55	Upper
56	Lower
57	Cleared
58	Current PV value
59	Current trim value
60	8.4f
61	Change current value to apply value for trim
62	Apply trim value
63	Invalid Unit Code
64	Device transmitter variable code
65	Xmtr Variable
66	Pri-Var
67	Sec-Var
68	Tri-Var
69	4th-Var
70	Pressure Tranmitter Sensor Type Code
71	Selected Sensor Type
72	GP 2
73	GP 2-1
74	GP 2-2
75	GP 3
76	GP 4
77	GP 4-1
78	GP 4-2
79	GP 4-3
80	GP 4-4
81	GV 4
82	GV 4-1
83	GV 4-2
84	GV 4-3
85	GV 4-4
86	GP 5
87	GP 5-1
88	GV 5
89	GP 6
90	GP 6-1
91	GV 6
92	GV 6-1
93	GP 7
94	GV 7
95	GP 8
96	GV 8
97	GP 9
98	GV 9
99	AP 4
100	AP 4-1
101	AP 4-2
102	AP 4-3
103	AP 4-4
104	AP 5
105	AP 5-1
106	AP 6
107	#G6
108	#G4
109	#G5
110	#G7
111	#A4
112	#A5
113	#A6
114	#SG0
115	#SG1
116	#SG2
117	#SG3
118	#SG4
119	#SA5
120	#SA6
121	#SA7
122	#SG8
123	#SG9
124	#SG10
125	#SG11
126	Invalid Transmitter Variable Code
127	LCD mode
128	LCD Display Mode
129	Normal> All Values
130	Normal> PV Only
131	Normal> % Only
132	Normal> mA Only
133	Eng> All Values
134	Eng> PV Only
135	Engr. Xfer Fnctn
136	Linear
137	Sqar Root
138	Decimal Place
139	Auto
140	#.#### (1-4)
141	##.### (2-3)
142	###.## (3-2)
143	####.# (4-1)
144	#####. (5-0)
145	Update Failure
146	Engr. Range Unit
147	User
148	User Defined Unit
149	Engr. LRV
150	Engr. URV
151	User Defined unit
152	Change current PV to zero adjustmet value
153	Adjust value
154	Select Zero Adjust mode
155	Adjust Mode
156	Zero Adj.
157	Cut-Off Value
158	5.2f
159	Cut-OFF Mode
160	Linear
161	Zero
162	Two Point Trim
163	Adjust Trim
164	Cut PV
165	Eng. Unit Change
166	More Status Clear
167	Temp Unit
168	Pressure Unit
169	Volumetric flow Unit
170	Velocity Unit
171	Length Unit
172	Time Unit
173	Mass & Mass Flow
174	Mass per volume
175	Autrol.Pressure
176	Device settings
177	Diagnostics
178	Maintenance
179	Offline
180	Temperature sensor
181	Concentration sensor
182	Operate
183	Autrol Setup
184	LCD output
185	Dynamic Variables
186	Device Status
187	PV Analog Channel Saturated
188	PV Analog Channel Fixed
189	Wireless
190	WirelessHART Device
191	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
192	Primary
193	Primary Analog Channel
194	Secondary
195	Secondary Analog Channel
196	Tertiary
197	Tertiary Analog Channel
198	Quaternary
199	Quaternary Analog Channel
200	Quinary
201	Quinary Analog Channel
202	Critical Power Failure
203	Lock all
204	Trim not supported
205	Configuration cannot be changed
206	Locked by gateway
207	Analog Input Channel
208	Analog Output Channel
209	Secondary Analog Channel Saturated
210	Tertiary Analog Channel Saturated
211	Quaternary Analog Channel Saturated
212	Quinary Analog Channel Saturated
213	Secondary Analog Channel Fixed
214	Tertiary Analog Channel Fixed
215	Quaternary Analog Channel Fixed
216	Quinary Analog Channel Fixed
217	Simulation active
218	The device is in simulation mode and the level output is not representative of the process.
219	Non-Volatile memory failure
220	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
221	Volatile memory error
222	The RAM memory check is invalid or maybe corrupt
223	Watchdog reset executed
224	A watchdog reset has been performed
225	Voltage conditions out of range
226	A voltage condition is outside its allowable range
227	Environmental conditions out of range
228	An internal or environmental condition is beyond acceptable limits.
229	Electronic failure
230	A hardware problem not related to the sensor has been detected.
231	Subdevice list changed
232	Duplicate master detected
233	Capacity Denied
234	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
235	Bandwidth allocation pending
236	Block transfer pending
237	Battery life
238	Percent range
239	Loop current
240	Primary variable
241	Secondary variable
242	Tertiary variable
243	Quaternary variable
244	Read receive time
245	Write date and time
246	Non-Volatile Clock
247	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
248	Clock Uninitialized
249	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
250	None
251	No restrictions
252	SI Only
253	Restricted to SI Unit codes only
254	Process automation device
255	Discrete device
256	Hybrid:Process automation+discrete
257	I/O System
258	WirelessHART Process automation device
259	WirelessHART Discrete device
260	WirelessHART Process automation+discrete
261	WirelessHART Gateway
262	WirelessHART Access point
263	WirelessHART Process adapter
264	WirelessHART Discrete adapter
265	WirelessHART enabled handheld/portable maintenance tool
266	Device Profile
267	US
268	United States of America
269	JP
270	Japan
271	DE
272	Germany
273	FR
274	France
275	ES
276	Spain
277	RU
278	Russian Federation
279	CN
280	People's Republic of China
281	Secondary Master
282	Primary Master
283	Device Diagnostic Status 0
284	Device Diagnostic Status 1
285	I/O and Subdevice Status
286	WirelessHART Status
287	Time Set Option
288	Real Time Clock Flags
289	Country
290	Country of intended device installation
291	SI Unit Control
292	Indicates if device should only display SI unit codes
293	8u
294	Dynamic Variables Returned for Device Variables
295	Command Response Truncated
296	Configuration Change Counter Mismatch
297	Status bytes mismatch
298	Output Status
299	Output Status Byte
300	Uninitialized
301	Normal - one sensor
302	Normal - two sensors
303	Normal - three sensors
304	Shorted
305	Shorted- shorted field wiring.
306	Limited high
307	Limited high- block can not respond to upward movement of value.
308	Open
309	Open- open field wiring.
310	Limited low
311	Limited low- block can not respond to upward movement of target.
312	Initialization done
313	Initialization done- block initialization is complete.
314	Not selected
315	Not selected- target value provided by block was not selected.
316	No path
317	No path- there is no path to the process.
318	Fail
319	Fail- hardware failure.
320	Bad
321	Bad- block is out of service or has bad input.
322	Not from process
323	Not from process- value is not directly affected by any process information.
324	Local override
325	Local override- block has LO mode.
326	Not Cascade Mode
327	Not RCas Mode
328	Not ROut Mode
329	No communication
330	No communication- (NO_COM).
331	uint16_var_blk_char
332	uint32_var_blk_char
333	uint8_var_blk_char
334	int8_var_blk_char
335	new itest redef1 label
Reference ID	String