Device dictionary

Loading…

Reference ID	String
0	APC-2000 ALW
1	Aplisens S.A.
2	Dev. Spec Status Byte 2
3	Device Specific Status Byte 2
4	Sensor Failure
5	Sensor Not Connected
6	Primary Variable Not Valid
7	Primary Variable Out Of Limits
8	Secondary Variable Out Of Limits
9	Analog Output Saturated
10	Output Current Fixed
11	Hot Start Occure
12	Dev. Spec Status Byte 3
13	Device Specific Status Byte 3
14	RAM Test Error
15	Flash CRC Error
16	Bad CRC In Segment INFO
17	Oscillator Fault
18	HT430 Init Error
19	ADC Interface Master Error
20	ADC Interface Slave Error
21	ADC Not Responded
22	AI Memory Diagnostics
23	INFO Fault
24	INFO Recovery
25	INFO Recovery Fault
26	Backup Info Fault
27	Backup Info Recovery
28	Backup Info Recovery Fault
29	Flash Consistency Fault
30	PB Memory Diagnostics
31	SB Memory Diagnostics
32	TB Memory Diagnostics
33	PB Diagnostics
34	PB LFXT1 Fault
35	PB Hart Fault
36	PB Local Loopback Fault
37	PB Remote Loopback Fault
38	PB Barrier Data Error
39	PB ADC Not Ready
40	PB MSP_Temp Over
41	PB MSP Temp Under
42	SB Diagnostics 1
43	SB Diagnostics
44	SB AVDD Status Error
45	SB TEMP Status Error
46	SB AIN1 Status Error
47	SB AIN2 Status Error
48	SB AIN3 Status Error
49	SB ADC Not Responded
50	SB ADC Temp Over
51	SB ADC Temp Under
52	SB Diagnostics 2
53	SB Head Temp Over
54	SB Head Temp Under
55	Analog Channel 1
56	Analog Channel 2
57	Analog Channel 3
58	Analog Channel 4
59	S-P acc. DIN 2512 Form N
60	S-P acc. DIN 2526 Form E
61	S-P acc. ANSI
62	S-Ch acc. DIN 2526 Form B
63	S-Ch acc. ANSI
64	S-T / T=50 acc. DIN 2512 Form N
65	S-T / T=50 acc. DIN 2526 Form E
66	S-T / T=50 acc. ANSI
67	S-T / T=100 acc. DIN 2512 Form N
68	S-T / T=100 acc. DIN 2526 Form E
69	S-T / T=100 acc. ANSI
70	S-T / T=150 acc. DIN 2512 Form N
71	S-T / T=150 acc. DIN 2526 Form E
72	S-T / T=150 acc. ANSI
73	S-T / T=200 acc. DIN 2512 Form N
74	S-T / T=200 acc. DIN 2526 Form E
75	S-T / T=200 acc. ANSI
76	S-TK-P
77	S-Comp
78	S-CompCh
79	S-Mazut
80	S-Clamp
81	S-DIN
82	S-SMS 38
83	S-SMS 50
84	S-SMSG 38
85	S-SMSG 50
86	S-Homogenizer
87	S-Varivent
88	S-Level 25
89	S-Level 50
90	S-DRD
91	S-CG1
92	S-CGS1
93	S-CG1 1”
94	S-M48x3
95	P-Bitum
96	S-RCM30x2
97	S-RCM30x1,5
98	S-RCG1
99	PTFE
100	NBR
101	EPDM
102	Silicon
103	FPM
104	Nominal Measuring Range
105	-250 ÷ 250 Pa
106	-700 ÷ 700 Pa
107	-2500 ÷ 2500 Pa
108	0 ÷ 2500 Pa
109	-0,25 ÷ 0,25 kPa
110	-0,7 ÷ 0,7 kPa
111	-2,5 ÷ 2,5 kPa
112	0 ÷ 2,5 kPa
113	-0,5 ÷ 7 kPa
114	-1,5 ÷ 7 kPa
115	-10 ÷ 10 kPa
116	-16 ÷ 16 kPa
117	0 ÷ 25 kPa
118	-50 ÷ 50 kPa
119	-100 ÷ 600 kPa
120	-160 ÷ 200 kPa
121	-160 ÷ 1600 kPa
122	0 ÷ 100 kPa
123	0 ÷ 200 kPa
124	-100 ÷ 150 kPa
125	0 ÷ 0,7 MPa
126	0 ÷ 1,6 MPa
127	0 ÷ 2,5 MPa
128	0 ÷ 7 MPa
129	0 ÷ 16 MPa
130	0 ÷ 30 MPa
131	0 ÷ 60 MPa
132	0 ÷ 100 MPa
133	0 ÷ 110 kPa ABS
134	0 ÷ 0,7 MPa ABS
135	0 ÷ 2,5 MPa ABS
136	0 ÷ 7 MPa ABS
137	0 ÷ -6000 mmH2O
138	0 ÷ -1600 mmH2O
139	0 ÷ 1,5 mH2O
140	0 ÷ 10 mH2O
141	0 ÷ 100 mH2O
142	Process Connection Type
143	M20x1,5
144	P
145	CM30x2
146	CM20x1,5
147	G 1/2”
148	G 1/4”
149	GP
150	CG1
151	CG 1/2”
152	RM
153	RG
154	C
155	PCV
156	1/2 NPT M
157	1/2 NPT F
158	1/1 NPT M
159	Process Connection Material
160	hastelloy c / stainless steel 316
161	hastelloy c / stainless steel 316L
162	Sensor Filling Fluid
163	AK20
164	DC550
165	M20
166	FS-5
167	Neobee
168	Static Pressure
169	35 kPa
170	100 kPa
171	1 MPa
172	4 MPa
173	10 MPa
174	16 MPa
175	25 MPa
176	32 MPa
177	40 MPa
178	42 MPa
179	Diaphragm Seal Size
180	DN25
181	DN40
182	DN50
183	DN65
184	DN80
185	DN100
186	A109
187	1”
188	1 1/2”
189	2”
190	3”
191	phi 50
192	phi 75
193	phi 100
194	Seal Diaphragm Material
195	teflon
196	Seal Contact Face Material
197	Seal Filling Fluid
198	Nominal Pressure
199	PN2,5
200	PN6
201	PN10
202	PN16
203	PN20
204	PN25
205	PN40
206	PN50
207	PN63
208	PN100
209	PN110
210	PN150
211	PN160
212	PN260
213	150Lb
214	300Lb
215	600Lb
216	1500Lb
217	2500Lb
218	Length Capillary H
219	0,5m
220	1m
221	1,5m
222	2m
223	3m
224	4m
225	5m
226	6m
227	7m
228	8m
229	9m
230	10m
231	11m
232	12m
233	13m
234	14m
235	15m
236	16m
237	17m
238	18m
239	19m
240	20m
241	21m
242	22m
243	23m
244	24m
245	25m
246	Length Capillary L
247	Configuration of Seal
248	H
249	L
250	H_L remote seal
251	H remote seal_L
252	H remote seal_L remote seal
253	6.3f
254	m H2O 4C
255
256	.3f
257	8.3f
258	7d
259	Lower current trim point
260	mA
261	Upper current trim point
262	Lower sensor trim point
263	Applied process pressure at which the last low sensor trim was performed.
264	Upper sensor trim point
265	Applied process pressure at which the last upper sensor trim was performed.
266	Current units
267	Kind of trim
268	User calibrations (sensor calibrations) are replaced by the original factory calibrations.
269	undo zero trim
270	sensor trim recall to factory settings
271	analog output trim recall to factory settings
272	Product code
273	Product code as generated from the product catalogue. It is related to the pressure trasmitter and its optional. A modification of the product code will not affect device functionally.
274	Separator code
275	Product code as generated from the product catalogue. It is related to the Remote Seal connected to the positive side of the transmitter. If no remote seal connected the code is blank. A modification of the product code will not affect device functionally.
276	Manifold code
277	Product code as generated from the product catalogue. It is related to the Remote Seal connected to the negative side of the transmitter.If no remote seal connected the code is blank. A modification of the product code will not affect device functionally
278	Long tag
279	Tag 24 ASCII character
280	Startpoint rad
281	Determines the transition from linear resp. 4mA-constant to square root (Transfer Function).
282	5.2f
283	Unit
284	Units code selectable for the Electronic Temperature variable
285	Value
286	.1f
287	Device temperature
288	Old customer security code
289	New customer security code
290	m_246
291	Customer code
292	Set protect code
293	x20
294	Polynomial Coefficient
295	3.1f
296	x19
297	x18
298	x17
299	x16
300	x15
301	x14
302	x13
303	x12
304	x11
305	x10
306	x9
307	x8
308	x7
309	x6
310	x5
311	x4
312	x3
313	x2
314	x1
315	x0
316	y20
317	Double Polynomial Coefficient
318	y19
319	y18
320	y17
321	y16
322	y15
323	y14
324	y13
325	y12
326	y11
327	y10
328	y9
329	y8
330	y7
331	y6
332	y5
333	y4
334	y3
335	y2
336	y1
337	y0
338	Local Operation
339	Enabled
340	Disabled
341	Meter Information Configuration
342	Integral LCD
343	Meter display mode
344	Unit On
345	Unit Off
346	Meter display contrast
347	NOT USED
348	LCD1 display variable
349	Current
350	Percent of Range
351	LCD2 display variable
352	Pressure
353	User Rerange
354	Pressure, no unit displayed
355	User Rerange, no unit displayed
356	LCD gap
357	GAP
358	Meter display decimal point
359	[.XXXXX]
360	[X.XXXX]
361	[XX.XXX]
362	[XXX.XX]
363	[XXXX.X]
364	[XXXXX.]
365	Empty Byte
366	cmd141_byte0
367	2d
368	cmd141_byte1
369	cmd141_byte2
370	HART modem error
371	HART modem state alarm
372	ADC7794 error
373	ADC7794 state alarm
374	EEPROM, RAM error
375	EEPROM & RAM state alarm
376	32768Hz oscillator error
377	32768Hz oscillator state alarm
378	DS33 error
379	DS33 state
380	empty_bit
381	Current Alarm
382	HIGH (22 mA)
383	LOW (3,6 mA)
384	Current Range Mode
385	NORMAL (3,9–20,5 mA)
386	NAMUR (3,8 – 20,5 mA)
387	Users Unit
388	Display Unit - Unit that is displayed on the LCD Display
389	Rearrange Shift
390	Rearrange Ampl
391	Channel Number
392	0
393	1
394	wrd_SSMod_H_2
395	Max pres unit
396	Units code selectable for the Max working press parameter.
397	Max work pres
398	Max process pressure applicable to the device for a correct working.
399	6.2f
400	Min pres unit
401	Units code selectable for the Min working press parameter.
402	Min work pres
403	Min process pressure applicable to the device for a correct working.
404	Min temp unit
405	Units code selectable for the Min temperature parameter.
406	Min temp value
407	Min temperature applicable to the device for a correct working.
408	Max temp unit
409	Units code selectable for the Max temperature parameter.
410	Max temp value
411	Max temperature applicable to the device for a correct working.
412	CPU hard major rev.
413	CPU hard minor rev.
414	CPU Hard Rev.
415	CPU Hardware Revision
416	4.2f
417	CPU Hardware Rev.
418	CPU soft major rev.
419	CPU Soft Rev.
420	CPU soft minor rev.
421	CPU Software Revision
422	Master soft major rev.
423	Master soft minor rev.
424	Master Soft Rev.
425	Master Software Revision
426	Master Software Rev.
427	Slave soft major rev.
428	Slave soft minor rev.
429	Slave Soft Rev.
430	Slave Software Revision
431	Slave Software Rev.
432	ADC hard major rev.
433	ADC hard minor rev.
434	ADC Hardware Rev.
435	ADC Hardware Revision
436	HART soft major rev.
437	HART soft minor rev.
438	hart_software_method
439	Hart Soft Rev.
440	Hart Software Revision
441	Hart Software Rev.
442	[invalid_unit_code]
443	[excess_correction_factors_out_of_limits]
444	Trim
445	Current chart
446	Analog Input/Output
447	Physical Block
448	Transducer Block
449	Last trim points
450	Set PV zero
451	Pressure of the process measured with respect to a reference pressure.
452	LCD
453	Local LCD
454	User Unit
455	variables and percent of range charts
456	PV Chart
457	SV Chart
458	TV Chart
459	QV Chart
460	Percent of range
461	Communication status
462	Field Device Status: Data indicating that the Field Device has detected condition(s) in the Field Device relating to: its hardware / the validity of a variable / its operating status / an internal process.
463	Commands status
464	Device Specific Status (Byte 2, 3)
465	Analog Input Memory Diagnostics
466	Physical Block Memory Diagnostics
467	Sensor Block Memory Diagnostics
468	Transducer Block Memory Diagnostics
469	Device Specific Status
470	Operational Modes
471	Analog Channel Saturated
472	Analog Channel Fixed
473	Device revision
474	CPU Temperature
475	Device Flags
476	Static Data Materials
477	Device identification
478	Separator and material code
479	Temp operational limits
480	Write protection
481	Set Write Protect
482	Change Protect Code
483	Sensor Temperature
484	ADC Temperatute
485	Analog input
486	SPAN
487	ZERO
488	Current Alarms
489	Set Lower Sensor Trim
490	Pressure Sensor Lower Trim: Calibrate the pressure sensor.
491	Set Upper Sensor Trim
492	Pressure Sensor Upper Trim: Calibrate the pressure sensor.
493	Leave trim mode
494	Return to Factory Settings
495	Reset Device Flag
496	Reset Configuration Changed Flag
497	Reset Device
498	Reset Device?
499	Linearization Table
500	Enable on token-passing data link layer only
501	Enable on TDMA data link layer only
502	Enable on both TDMA and token-passing data link layer
503	Wireless
504	WirelessHART Device
505	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
506	Primary
507	Primary Analog Channel
508	Secondary
509	Secondary Analog Channel
510	Tertiary
511	Tertiary Analog Channel
512	Quaternary
513	Quaternary Analog Channel
514	Quinary
515	Quinary Analog Channel
516	Critical Power Failure
517	Lock all
518	Trim not supported
519	Configuration cannot be changed
520	Locked by gateway
521	Analog Input Channel
522	Analog Output Channel
523	Secondary Analog Channel Saturated
524	Tertiary Analog Channel Saturated
525	Quaternary Analog Channel Saturated
526	Quinary Analog Channel Saturated
527	Secondary Analog Channel Fixed
528	Tertiary Analog Channel Fixed
529	Quaternary Analog Channel Fixed
530	Quinary Analog Channel Fixed
531	8u
532	Device Variable
533	Press OK to Set Protect Code
534	%{cpu_hardware_rev}
535	%{cpu_software_rev}
536	%{master_software_rev}
537	%{slave_software_rev}
538	%{adc_hardware_rev}
539	%{hart_software_rev}
540	Press OK to Factory Trim
541	Press OK to Set PV Zero
542	Type Protect Code
543	Type Old Customer Code
544	Type new Customer Code
545	Press OK to Set Span
546	Press OK to Set Zero
547	Set the channel number
548	Apply low pressure
549	What is the pressure ?
550	Pressure is stable
551	Enter applied pressure value
552	trim_point
553	Remove_pressure
554	Apply hi press
555	Remove pressure
556	Trim was not done
557	Press OK to Reset Configuration Changed Flag
558	Press OK to Reset Device
Reference ID	String