Device dictionary

Loading…

Reference ID	String
0	PV Unit
1	Sensor (PV)
2	Sensor
3	.2f
4	Sensor Uppper Limit
5	3.2f
6	Sensor Lower Limit
7	Sensor Min Span
8	Snsr1 Measurement- Measurement input that receives some analog
9	Snsr1
10	Sensor probe type
11	0...500 Ohm
12	0...5000 Ohm
13	Pt50 (IEC751)
14	Pt100 (IEC751)
15	Pt200 (IEC751)
16	Pt500 (IEC751)
17	Pt1000 (IEC751)
18	Pt50 (JIS1604)
19	Pt100 (JIS1604)
20	Pt50 (MIL24388)
21	Pt100 (MIL24388)
22	Pt200 (MIL24388)
23	Pt1000 (MIL24388)
24	Ni50 (DIN43760)
25	Ni100 (DIN43760)
26	Ni120 (DIN43760)
27	Ni1000 (DIN43760)
28	Cu10 a=4270
29	Cu100 a=4270
30	-125.. 125 mV
31	-125..1200 mV
32	TC Type B (IEC584)
33	TC Type C (ASTME988)
34	TC Type D (ASTME988)
35	TC Type E (IEC584)
36	TC Type J (IEC584)
37	TC Type K (IEC584)
38	TC Type N (IEC584)
39	TC Type R (IEC584)
40	TC Type S (IEC584)
41	TC Type T (IEC584)
42	TC Type L (DIN43710)
43	TC Type U (DIN43710)
44	Sensor wire number
45	2-wire
46	3-wire
47	4-wire
48	Sensor probe connection
49
50	Sensor CJC type
51	Internal
52	Standard
53	Fixed
54	Fixed to a manual value (thermostate)
55	None
56	Not used
57	Sensor CJC temperature unit
58	Sensor CJC temperature
59	Sensor resistance two wire
60	Sensor bias
61	Sensor input engineering unit
62	Sensor output engineering unit
63	Select sensor probe type
64	Unsupported Probe Type
65	Invalid Number Of Wires
66	Device state
67	OK
68	No fault was found in the transmitter or sensor function. The diagnostic data may contain status information, stating e.g. that data is being stored in the non-volatile memory.
69	Check
70	The transmitter's process data or diagnostic information is being simulated. The output process value and displayed diagnostic data may not represent the actual situation.
71	Out of Specification
72	The transmitter or the sensors are not working under the specified operating conditions. Under these circumstances, the specified device properties may no longer be achieved. If the element is used under these unfavorable conditions repeatedly or for a longer time period, its service life may be shorter than specified.
73	Maintenance Required
74	The sensor or essential transmitter parts are defective. However, it is still possible to execute the configured measuring tasks, though to a limited extent. If sensor redundancy is configured, the failure of a sensor will not affect the primary variable. If the transmitter indicates that maintenance is required, this means that the maintenance personnel should service the device as soon as possible to avoid a failure of this tag.
75	Failure
76	The sensor or essential transmitter parts are defective. However, the primary variable and, thus, the current output is not necessarily and in any case affected. If e.g. the measuring signal from sensor 1 is assigned to the PV and sensor 2 fails, the device status assumes the value Failure, whereas the current output continues to provide valid measuring values.
77	Diag_Reserved0
78	Diag_Reserved1
79	Diag_Reserved2
80	Diag_Reserved3
81	Diag_Reserved4
82	Diag_Reserved5
83	CommunicationA
84
85	CommunicationB
86	Application
87	Configuration / parameterization failure
88	Reconfiguration in progress
89	Application failure
90	Analog output trim active
91	Analog output is fixed/simulated
92	Warning
93	Sensor
94	Leads resistance too high
95	Short circuit
96	Open line
97	Sensor range overrun
98	Sensor range underrun
99	1-point trim is active
100	Electronics
101	Device temperature measurement failure
102	Device temperature out of specification
103	EEPROM defect
104	EEPROM write cycles exceeded
105	EEPROM Data Defect
106	Parameter Failure
107	HMI (display) not connected
108	Device is write protected
109	EEPROM busy
110	Data being saved in non-volatile memory. Do not switch off the transmitter.
111	Sensorboard comm. error
112	Hardware error. 1) Restart (RESET). 2) Replace transmitter.
113	Sensorboard failure
114	Sensorboard ADC failure
115	Identify
116	Snsr1 Units
117	Electrical Input (TV)
118	Electrical Input
119	Sensor Upper Limit
120	Sensor Min Span
121	Snsr1 Measurement- Measurement input that receives some analog
122	Elec1
123	Unit
124	Terminal temperature (or ambient temperature).
125	Electronics Temperature (SV)
126	Termnl USL
127	Termnl LSL
128	Termnl min span
129	Electr. Temp
130	One point trim
131	Two point trim
132	Reset trim
133	ABB
134	TTX200 series
135	To (20mA)
136	Range (4mA)
137	SW version major
138	SW version minor
139	SW version revision
140	HW version major
141	HW version minor
142	Sensor serial number
143	1u
144	8u
145	Damping
146	s
147	Range unit
148	Electric input
149	Electronics temperature
150	upload list
151	download list
152	Configure
153	Overrange value
154	2.2f
155	mA
156	Underrange value
157	1.2f
158	Reaction on errors
159	Overrange
160	Underrange
161	Current output
162	Parameterize
163	Observe
164	sensor trim low
165	sensor trim Value
166	sensor trim low
167	4.1f
168	sensor trim high
169	3.1f
170	Sensor trim support
171	1-point trim
172	2-point trim
173	1-point and 2-point trim
174	Sensor Trim
175	Current Output Trim
176	Calibrate
177	Device state
178	Diagnose
179	Simulate
180	Extra
181	Write protection
182	Write protected
183	Not protected
184	Software write protection
185	password
186	Reset to factory
187	Perform a Reset to Factory Data.
188	Range unit
189	Analog Value
190	FMU860
191	DT
192	DVC
193	FCX
194	AS800
195	340T
196	340C
197	344
198	Siemens Micro K
199	SITRANS L
200	SIPAN PH
201	SITRANS P
202	75SMT
203	UNIDELTA
204	8320
205	SX5100
206	TSV175
207	DMU
208	3780
209	BM70
210	8.3f
211	.3f
212	New sensor type
213	Select wire number
214	Select CJC type
215	Enter lower trim value
216	Enter upper trim value
217	Really reset to factory settings?
Reference ID	String