Device dictionary

Loading…

Reference ID	String
0	82EC COND
1	Four-Electrode Conductivity Transmitter
2	ABB Instrumentation
3	EC1 HI.PV.AD
4	Process Variable A/D over range
5	EC2 LO.PV.AD
6	Process Variable A/D under range
7	EC3 PH.PCB
8	pH/ORP/pION input PCB with Conductivity/concentration firmware
9	EC4 TC.PCB
10	Toroidal conductivity input PCB with 4-electrode conductivity/concentration firmware
11	EC6 TE.PCB
12	2-electrode conductivity input PCB with 4-electrode conductivity/concentration firmware
13	EC7 EC.PCB
14	Electrode conductivity input PCB with 4-electrode conductivity/concentration firmware
15	PC3 DRTY.SN
16	Dirty Sensor detected
17	PC4 GND LP
18	Ground loops present or shorted sensor cable
19	PC6 HI.LOOP
20	Current loop above upper range
21	PC7 LO.LOOP
22	Current loop below lower range value
23	PC8 HI.PV
24	PV above transmitter range
25	PC9 LO.PV
26	PV below transmitter range
27	PC10 HI.TEMP
28	Temperature above transmitter range
29	PC11 LO.TEMP
30	Temperature below transmitter range
31	PC12 HI.T.AD
32	Open or missing Temperature Sensor
33	PC13 LO.T.AD
34	Shorted Temperature Sensor
35	PC2O BAD.SEE
36	Bad SEEPROM or bad input PCB assembly
37	PC21 NO.F.CAL
38	Missing factory cal or nonfunctional SEEPROM
39	PC22 BLNK.EE
40	Blank microprocessor EEPROM
41	PC25 ROM.SUM
42	Incorrect EPROM checksum
43	PC30 R0.F.CAL
44	Out of range or missing factory cal for conductivity circuit range zero
45	PC31 R1.F.CAL
46	Out of range or missing factory cal for conductivity circuit range one
47	PC32 R2.F.CAL
48	Out of range or missing factory cal for conductivity circuit range two
49	PC33 R3.F.CAL
50	Out of range or missing factory cal for conductivity circuit range three
51	PC34 R4.F.CAL
52	Out of range or missing factory cal for conductivity circuit range four
53	PC35 G0.F.CAL
54	Out of range or missing factory cal for ground loop circuit range zero
55	PC36 G1.F.CAL
56	Out of range or missing factory cal for ground loop circuit range one
57	PC37 G2.F.CAL
58	Out of range or missing factory cal for ground loop circuit range two
59	PC38 G3.F.CAL
60	Out of range or missing factory cal for ground loop circuit range three
61	PC39 G4.F.CAL
62	Out of range or missing factory cal for ground loop circuit range four
63	PC45 BA.F.CAL
64	Out of range or missing factory cal for 3-k ohm Balco temp.compensator
65	PC46 PT.F.CAL
66	Out of range or missing factory cal for PT100 temp. compensator
67	PC47 RT.F.CAL
68	Out of range or missing factory cal for 4.75-k ohm RTD network temp. compensator
69	PC50 R0.CHKS
70	Incorrect or missing conductivity circuit range zero checksum
71	PC51 R1.CHKS
72	Incorrect or missing conductivity circuit range one checksum
73	PC52 R2.CHKS
74	Incorrect or missing conductivity circuit range two checksum
75	PC53 R3.CHKS
76	Incorrect or missing conductivity circuit range three checksum
77	PC54 R4.CHKS
78	Incorrect or missing conductivity circuit range four checksum
79	PC55 G0.CHKS
80	Incorrect or missing ground loop circuit range zero checksum
81	PC56 G1.CHKS
82	Incorrect or missing ground loop circuit range one checksum
83	PC57 G2.CHKS
84	Incorrect or missing ground loop circuit range two checksum
85	PC58 G3.CHKS
86	Incorrect or missing ground loop circuit range three checksum
87	PC59 G4.CHKS
88	Incorrect or missing ground loop circuit range four checksum
89	PC65 BA.CHKS
90	Incorrect or missing 3-k ohm Balco temp. compensator checksum
91	PC66 PT.CHKS
92	Incorrect or missing PT100 temp. compensator checksum
93	PC67 RT.CHKS
94	Incorrect or missing 4.75-k ohm network temp. compensator checksum
95	PC70 HI.G.L.AD
96	Ground loop signal above transmitter A/D range
97	PC71 LO.G.L.AD
98	ground loop signal below transmitter A/D range
99	PC72 HI.D.S.AD
100	Dirty sensor signal above transmitter A/D range
101	PC73 LO.D.S.AD
102	Dirty Sensor signal below transmitter A/D range
103	PV LO OFFSET
104	PV calibration Offset too low
105	PV LO SLOPE
106	PV calibration Slope too low
107	PV HI OFFSET
108	PV calibration Offset too high
109	PV HI SLOPE
110	PV calibration Slope too high
111	Temp Offset Warning
112	Temperature calibration Offset unacceptable
113	Temp Slope Warning
114	Temperature calibration Slope unacceptable
115	PV eng. unit
116	micro siemens per centimeter
117	Conductivity - Temperature compensated process solution conductivity.
118	.3f
119	.2f
120	8.2f
121	11.3f
122	8u
123	Temp Unit
124	Temperature- In Auto temp comp mode, it is the Temp read with the temp sensor. In Manual temp comp mode, it is the user entered temp value
125	In calibration security mode
126	Transmitter Busy - Cannot Process Command
127	10.3f
128	PV slope
129	PV sensor slope value
130	PV offset
131	PV sensor offset value.
132	Temperature sensor Slope
133	Temperature sensor offset
134	Temperature sensor offset value.
135	Cond cal value
136	Conductivity calibration value
137	Temp. calibration value
138	Temperature calibration value
139	HART Parameters
140	Offline Configuration Parameters
141	PV Range Setup
142	Units code warning
143	unit warning
144	Reset Transmitter
145	Reset Transmitter - Instructs the transmitter to generate a reset. The result is similar to the effects of briefly interrupting power to the transmitter. This can be used to recover from an error condition if needed.
146	Conductivity cal
147	Calibration of process sensor input via one-point smart calibration that adjusts offset and slope.
148	Temp. Cal
149	Calibration of Temperature sensor input via one-point smart calibration that adjusts offset and slope
150	Edit Cal
151	Manual adjustment of process sensor and temperature offset and slope values
152	Reset Cal
153	Reset the process and temperature sensor calibration data to the values set at the factory
154	Refresh variables
155	Read transmitter variables to refresh their values. This will update any variable that was modified via the device keypad.
156	FMU860
157	DT
158	DVC
159	FCX
160	AS800
161	340T
162	340C
163	344
164	Siemens Micro K
165	SITRANS L
166	SIPAN PH
167	SITRANS P
168	75SMT
169	UNIDELTA
170	8320
171	SX5100
172	TSV175
173	DMU
174	3780
175	BM70
176	low
177	high
178	tmp_av
179	Variables which use this as the units code will be in the previous units until this value is sent to the device.
180	Transmitter will be Reset! Continue?
181	Transmitter Reset is in process, please wait.
182	Reading current values of all transmitter variables, please wait.
183	Transmitter Reset successful
184	Press OK when PV is stable %0 %{3}
185	Enter new value:
186	PV Slope: %{1} PV Offset: %{2} uS/cm
187	Calibration was not successful. Do you want to retry?
188	Calibration was successful
189	Enter Temperature:
190	TEMP OFFSET WARNING
191	TEMP SLOPE WARNING
192	Edit PV Slope
193	Edit PV Offset
194	Edit Temp. Slope
195	Edit Temp. Offset
196	Press OK to Reset Calibration
197	Reading transmitter variables, please wait.
Reference ID	String