Device dictionary

Loading…

Reference ID	String
0	pdpCustomerMaxMinValues units
1	inH2O (68°F)
2	inHg (0°C)
3	ftH2O (68°F)
4	mmH2O (68°F)
5	mmHg (0°C)
6	psi
7	bar
8	mbar
9	g/cm2
10	kg/cm2
11	Pa
12	kPa
13	torr (0°C)
14	atm
15	inH2O (60°F)
16	MPa
17	inH2O (4°C)
18	mmH2O (4°C)
19	sensorTemperatureCustomerMaxMinValues units
20	°C
21	°F
22	°R
23	K
24	Vom Druckmesswerk erreichter Mindestwert
25	Min. Druckwert
26	.3f
27	Vom Druckmesswerk erreichter Höchstwert
28	Max. Druckwert
29	Vom Temperaturmesswerk erreichter Mindestwert
30	Min. Temperaturwert
31	.2f
32	Vom Temperaturmesswerk erreichter Höchstwert
33	Max. Temperaturwert
34	pdpServiceMaxMinValues units
35	sensorTemperatureServiceMaxMinValues units
36	array ServiceMaxMin
37	index array ServiceMaxMin
38	reset customerMaxMinValues
39	reset serviceMaxMinValues
40	Simulation Status
41	Gesperrt
42	Freigegeben
43	pdpSimulation units
44	Druckwert
45	sensorTemperatureSimulation units
46	Messwerkstemperatur
47	array SimulationValues
48	index array_SimulationValues
49	Prozessvariable auf gewünschten Wert setzen
50	pdpBiasValue units
51	Valore dell'Offset necessario per elevare o sopprimere la PV affinchè sia uguale a quella desiderata
52	Offset Wert
53	Einheit
54	Unit for digital output
55	ft3/min
56	gal/min
57	L/min
58	ImpGal/min
59	m3/h
60	ft/s
61	m/s
62	gal/s
63	Million gal/d
64	L/s
65	MillionL/d
66	ft3/s
67	ft3/d
68	m3/s
69	m3/d
70	ImpGal/h
71	ImpGal/d
72	mV
73	Ohms
74	Hz
75	mA
76	gal
77	L
78	ImpGal
79	m3
80	ft
81	m
82	barrels
83	in
84	cm
85	mm
86	min
87	s
88	h
89	d
90	cST
91	cP
92	microS
93	%
94	V
95	pH
96	g
97	kg
98	t
99	lb
100	STon
101	LTon
102	mS/cm
103	microS/cm
104	N
105	N.m
106	g/s
107	g/min
108	g/h
109	kg/s
110	kg/min
111	kg/h
112	kg/d
113	t/min
114	t/h
115	t/d
116	lb/s
117	lb/min
118	lb/h
119	lb/d
120	STon/min
121	STon/h
122	STon/d
123	LTon/h
124	LTon/d
125	decaTherm
126	SGU
127	g/cm3
128	kg/m3
129	lb/gal
130	lb/ft3
131	g/ml
132	kg/L
133	g/L
134	lb/in3
135	STon/yd3
136	°Twad
137	°Baum (hv)
138	°Baum (lt)
139	°API
140	% sol/wt
141	% sol/vol
142	°Ball
143	proof/vol
144	proof/mass
145	Bushel
146	yd3
147	ft3
148	in3
149	in/s
150	in/min
151	ft/min
152	deg/sec
153	rps
154	rpm
155	m/h
156	m3/h normal
157	L/h normal
158	ft3/min std
159	bbl (liq)
160	oz
161	ft·lbf
162	kW
163	kW·h
164	hp
165	ft3/h
166	m3/min
167	barrels/s
168	barrels/min
169	barrels/h
170	barrels/d
171	gal/h
172	ImpGal/s
173	L/h
174	ppm
175	Mcalth/h
176	MJ/h
177	Btuth/h
178	deg
179	rad
180	micro g/L
181	icro g/m3
182	%Consistency
183	% vol
184	% stm qual
185	Ft in Sixteenths
186	ft3/lb
187	pF
188	ml/L
189	micro l/L
190	%Plato
191	% Lower Explosion Level
192	Mcalth
193	Kohms
194	MJ
195	Btuth
196	m3 normal
197	L normal
198	ft3 std
199	ppb
200	gal/d
201	hl
202	None
203	Custom Unit
204	Messende
205	Upper limit for digital output
206	Messanfang
207	Lower limit for digital output
208	Special unit
209	Sondereinheit
210	Min. Betriebstemperatur
211	Minimum limit of temperature within the sensor is compensated as from data sheet
212	Max. Betriebstemperatur
213	Maximum limit of temperature within the sensor is compensated as from data sheet
214	Messwerkstemperatur Trim Value
215	Ermöglicht Vorort-Bedienung über Drucktasten
216	Vorort-Bedienung
217	Curve only for the variable to be displayed
218	Kennlinientyp
219	Linear
220	Radizierung
221	Xexp3/2
222	Xexp5/2
223	Linearisierungstabelle 22 Wertepaare
224	Bidirektionale Radizierung
225	Zylindrischer Tank, feste Tabelle
226	Kugeltank, feste Funktion
227	Unit of the variable to be displayed
228	Unit
229	Upper Range of the variable to be displayed
230	Upper Range Value
231	Lower Range of the variable to be displayed
232	Lower Range Value
233	Display language
234	Sprache
235	Englisch
236	Deutsch
237	Franzï¿½sisch
238	Spanisch
239	Italienisch
240	Display luminosity
241	Kontrast
242	Selection of the lines to be used for the display
243	Anzeige-Modus
244	Eine Zeile
245	Eine Zeile + Balkendiagramm
246	Zwei Zeilen
247	Zwei Zeilen + Balkendiagramm
248	Variable to be displayed on line 1
249	Ansicht Zeile 1
250	Druck
251	Skalierter Ausgang
252	Stromausgang
253	Prozent Ausgang
254	Messwerkstemperatur
255	HMI Skalierter Ausgang
256	Variable to be displayed on line 2
257	Ansicht Zeile 2
258	Variable to be represented on the bargraph
259	Balkendiagramm-Ansicht
260	Software revision of the display when it is installed
261	Anzeige-Revision
262	Nicht vorhanden
263	1
264	2
265	3
266	4
267	5
268	6
269	7
270	8
271	9
272	10
273	11
274	12
275	13
276	14
277	15
278	16
279	17
280	18
281	19
282	20
283	21
284	22
285	23
286	24
287	25
288	26
289	27
290	28
291	29
292	30
293	31
294	32
295	33
296	34
297	35
298	36
299	37
300	38
301	39
302	40
303	41
304	42
305	43
306	44
307	45
308	46
309	47
310	48
311	49
312	50
313	51
314	52
315	53
316	54
317	55
318	56
319	57
320	58
321	59
322	60
323	61
324	62
325	63
326	64
327	65
328	66
329	67
330	68
331	69
332	70
333	71
334	72
335	73
336	74
337	75
338	DecimalPoints line 1
339	0
340	DecimalPoints line 2
341	resetPdpBias
342	Aktueller Wert der Referenz
343	Unterer Abgleichpunkt
344	Oberer Abgleichpunkt
345	No. of points enabled
346
347	Current table status
348	Table status
349	Good
350	New Table Not Monotonic
351	New Table Not Enough Value
352	Value Not Exp
353	No Init
354	New Operation
355	Last Value
356	Change X,Y Point
357	HW version major
358	SW version major
359	dummy_revision_byte0
360	dummy_revision_byte1
361	dummy_revision_byte2
362	sensor revision byte 0
363	sensor revision byte 1
364	sensor revision byte 2
365	Materiale della membrana bagnata sul lato meno
366	Membranwerkstoff
367	Undefined
368	Monel
369	Tantal
370	Keramik
371	AISI 316L Nichtrostender Stahl
372	Hastelloy C276
373	Hastelloy C276 goldbeschichtet
374	Monel goldbeschichtet
375	PTFE Hastelloy
376	Monel 400
377
378	Füllflüssigkeit des Messwerks
379	Füllflüssigkeit
380	Silikonï¿½l
381	Fluorkohlenstoff
382	Weiï¿½ï¿½l (FDA)
383	Inert (Galden)
384	Glyzerin + H2O
385	Santotherm
386	Silikonï¿½l Lebensmittelgeignet
387	Pflanzenï¿½l Neobee
388	Dowtherm
389	Ethyl Benzene
390	Ethyl Alkohol
391	Prophylene Glykol/Wasser
392	ABB Fï¿½llung (dibutyl penthalate)
393	Syltherm 800
394	Quecksilber
395	DC97 9120 Pharma-B-Grade
396	Mineralï¿½l (Marcol 82)
397	Hochtemperatur Silikonï¿½l AN140
398	Niedrigtemperatur Silikonï¿½l Syltherm XLT
399	Inert (Halocarbon 4.2)
400	Nicht benutzt
401	Materiale della connessione di processo di un sensore di pressione relativa
402	Werkstoff Prozessanschluss
403	Kohlenstoffstahl
404	AISI 304SS
405	AISI 316 Nichtrostender Stahl
406	Hastelloy C
407	Kynar
408	17-PH-17
409	Art Prozessanschluss auf Plusseite der Differenzmessumformer
410	Anschlussart
411	Konventionell
412	Druckfï¿½hle
413	Flanschdruckfï¿½hler mit Flachmembran
414	Flanschdruckfï¿½hler mit Tubus
415	Verschweiï¿½ter Flansch
416	Fï¿½llhï¿½he Sanitï¿½r
417	Fï¿½llhï¿½he fï¿½r Lebensmittel
418	Direktanschluss
419	Vollverschweiï¿½t fï¿½r Druckfï¿½hler
420	Abgedichtet fï¿½r Druckfï¿½hler
421	Druckfï¿½hler in Kompaktbauweise
422	Innenliegende Membran
423	Verschweiï¿½te Buchse
424	Chemical T
425	Mit Gewinde
426	364 Flansch Typ
427	Werkstoff Prozessanschluss auf Plusseite der Differenzmessumformer
428	Kappenwerkstoff
429	AISI 304SS
430	Werkstoff messstoffberührte Dichtung auf Plusseite der Differenzmessumformer
431	Werkstoff O-Ring
432	AISI 316 SS
433	PTFE
434	Viton
435	Buna-N
436	Ethyl Prop.
437	Nitril Gummi (Perbunan NBR)
438	Aluminium
439	TFE Glasgefï¿½llt
440	Perfluor Elastomer
441	EPDM
442	Graphite
443	Silikongummi
444	Garlock
445	Materiale della spina sul lato più di un sensore di pressione differenziale
446	Verschlussstopfen
447	Anzahl der Druckfühler
448	Nummer
449	Ein
450	Zwei
451	Einer Minusseite
452	Einer Plusseite
453	Type of remote seal on the side H of the Sensor
454	Typ
455	Zellenbauweise
456	Gewindeanschluss innenliegende Membran
457	Chemical T
458	Membrankleindruckfï¿½hler
459	Triclamp & Cherry Burrell
460	Lebensmittel (ï¿½berwurfmutter)
461	Kleindruckfï¿½hler
462	Aseptisch
463	Flanschanschluss innenliegende Membran
464	Bï¿½ndige Sanitï¿½rmembran
465	Sanitï¿½rmembran mit Tubus
466	Flacher Flansch
467	Flansch mit Tubus
468	Harnstoffverarbeitung
469	Pulp & Paper
470	Getrï¿½nk
471	Monel
472	Tantalum
473	AISI 316L Stainless Steel
474	Inconel
475	Hastelloy C276
476	AISI 316L TFE Coated
477	Monel Gold Plated
478	Hastelloy C276 TFE Coated
479	Monel 400
480	Duplex SS
481	Inert (Galden)
482	Glyzerin + H2O
483	Hochtemperatur Silikonï¿½l (AN140)
484	Niedrigtemperatur Silikonï¿½l (Syltherm XLT)
485	Hochtemperatur Silikonï¿½l (DC740)
486	Silikonï¿½l (Baysilone M5 / 5 Cts)
487	Silikonï¿½l (DC200/ 10 Cts)
488	Mineralï¿½l (Marcol 122)
489	Galden HT55
490	Sensor communication error
491	Reserved
492
493	Ausgang im Fehlerfall
494	Auswahl von Hochalarm oder Tiefalarm
495	Hï¿½he
496	Niedrig
497	Untere Grenze des analogen Ausgangsstroms
498	Minimalstrom
499	Obere Grenze des analogen Ausgangsstroms
500	Maximalstrom
501	Wert für den Tiefalarmstrom (< 4mA) im Fehlerfall
502	Tiefalarmstrom
503	8.2f
504	Wert für den Hochalarmstrom (> 20mA) im Fehlerfall
505	Hochalarmstrom
506	Alarmsteuerung
507	Steuerung des Alarmverhaltens über DIP-Schalter oder Bedienprogramm
508	Hardware Fail Safe Type
509	Software Fail Safe Type
510	Der aktuelle Messwert entspricht:
511	New Lower range push upper range out of sensor limits
512	pdpValue_units
513	sensorTemperatureValue_units
514	pdpTrimValue units
515	Kalibrieren Druck
516	Maximum Working Pressure Units - The units of the Maximum working pressure.
517	maxWorkingPressure units
518	Maximale Druckgrenze, in der das Messwerk kompensiert wird.
519	Max. Betriebsdruck
520	serialNo_Part0
521	serialNo_Part1
522	serialNo_Part2
523	serialNo_Part2a
524	serialNo_Part3
525	serialNo_Part4
526	serialNo_Part5
527	snsrSerialNo_Part0
528	snsrSerialNo_Part1
529	snsrSerialNo_Part2
530	snsrSerialNo_Part3
531	snsrSerialNo_Part4
532	opCode_saveActualTrimming
533	Save Actual Trimming
534	opCode_resetSensorTrimming
535	Reset Sensor Trimming
536	resetToDefault
537	save to default
538	diagnosisConditionNumber
539	diagnosisConditionDetailsClass
540	diagnosisConditionDetailsGroup
541	diagnosisConditionDetailsPriority
542	diagnosisConditionDetailsAlarmCounter
543	diagnosisConditionDetailsAlarmTimeCounterDay
544	diagnosisConditionDetailsAlarmTimeCounterMsec
545	diagnosisConditionDetailsTimeStampLastAlarmDay
546	diagnosisConditionDetailsTimeStampLastAlarmMsec
547	diagnosisConditionDetailsCodes0
548	diagnosisConditionDetailsCodes1
549	diagnosisConditionDetailsCodes2
550	diagnosisConditionDetailsCodes3
551	diagnosisConditionDetailsCodes4
552	diagnosisConditionDetailsCodes5
553	diagnosisConditionDetailsCodes6
554	diagnosisConditionDetailsCodes7
555	diagnosisConditionDetailsCodes8
556	diagnosisConditionDetailsCodes9
557	diagnosisConditionDetailsCodes10
558	diagnosisConditionDetailsCodes11
559	diagnosisConditionDetailsCodes12
560	diagnosisConditionDetailsCodes13
561	Diagnosis Masking Byte 0
562	P-dP auï¿½erhalb der Grenzwerte
563	Messwerktemperatur auï¿½erhalb der Grenzwerte
564	Diagnosis Masking Byte 1
565	Dummy
566	Diagnosis Masking Byte 2
567	Fehler im stromausfallsicheren Speicher
568	Speicherfehler
569	Diagnosis Masking Byte 3
570	Max. Arbeitsdruck ï¿½berschritten
571	Diagnosis Masking Byte 4
572
573	Analogausgang gesï¿½ttigt
574	Warnung Spannungsversorgung
575	Diagnosis Masking Byte 5
576	Falscher Ausgangsstrom
577	Elektronik-Temperatur auï¿½erhalb der Grenzwerte
578	Diag Simulation
579	By enabling diagnosis simulation, any one diagnosis can be simulated at a time. Actual device diagnosis are not reported when diagnosis simulation is turned ON
580	Aus
581	Ein
582	Diagnosis Simulation Group0
583	P-dP Messwerkfehler
584	Fehler Messwerk-Temperatur
585	Fehler Elektronisch-Temperatur
586	Diagnosis Simulation Group1
587	Diagnosis Simulation Group2
588	Messwerk-Speicherfehler
589	Diagnosis Simulation Group3
590	Fehler im Sensor Nichtflüchtiger Speicher
591	Eingangssimulation aktiv
592	Diagnosis Simulation Group4
593	Schleifentest
594	Analogausgang gesättigt
595	Warnung Spannungsversorgung
596	Diagnosis Simulation Group5
597	Electronic Temperature Out of Limits
598	Device family status
599	Bit 1
600	Bit 2
601	Bit 3
602	Bit 4
603	Bit 5
604	Bit 6
605	Bit 7
606	Bit 8
607	Pressure status 0
608	Pressure sensor break
609	Temperature sensor break
610	Static-Pressure sensor break
611	Pressure Calibration Required
612	Pressure Operating Range Exceeded
613	Temperature Operating Range Exceeded
614	Static-Pressure Operating Range Exceeded
615	Reserviert
616	Device family capability 0
617	Max Pressure
618	Max Temperature
619	Max Static-Pressure
620	Optional-Gasket materials
621	Remote Seal info
622	Write Process Connection
623	Write Optional Gas Materials
624	Write Remote Seal info
625	Device family capability 1
626	family Def Revision
627	Type of Sensor
628	Messwerkstyp
629	Differenzdruck
630	Gauge Pressure
631	AP
632	AgP
633	Sensor Technology
634	Maximum limit of temperature within the electronic is compensated as from data sheet
635	Elektronische Temperatur Trim Value
636	Dear user, this device is not enabled to support the Digital Access Diagnostics function (Dynamic QR code). To enable this feature, please contact your local ABB sales or service office
637	select Information
638	Slect information number to send to device
639	Information 1
640	Information 2
641	Information 3
642	Information 4
643	Information 5
644	Select User
645	Channel partner QR Code
646	Diagnostic QR Code
647	QR Code View
648	Disabled
649	Enabled
650	QR Code View
651	Online
652	Identifizieren
653	Detailliertes Setup
654	Druckfühler
655	Allgemeines
656	Messwerk Setup
657	Werkstoffe Messwerk
658	P-dP
659	Prozessvariable [P/dP]
660	Skalierung
661	Prozessvariable Offset (Bias)
662	Übertragungsfunktion
663	Ausgang [P/dP]
664	HART Zuordnung
665	HART Indicatore
666	Bedienen
667	Extras
668	Zurücksetzen
669	Rücksetzen
670	Speichervorgänge
671	Werkseinstellungen laden
672	Simulation
673	Input Simulation
674	Kalibrieren
675	Diagnose
676	Diagnoseüberwachung
677	Failure
678	Maintenance Required
679	Out of Specification
680	Function Check
681	Konfiguration
682	Historien-Information
683	Protokollierung Druckvariable
684	Protokollierung Temperaturmesswerk
685	Geräteeinstellungen
686	Easy setup
687	Prozess Variable
688	Allgemein
689	Applikation
690	www.abb.com
691	Image of Transmitter
692	Image of the Transmitter
693	Device image
694	Prozesswert[mA]
695	Low alarm
696	Low saturation
697	High saturation
698	High alarm
699	Offline
700	Identifizierung
701	P-dP Messwerk
702	Betriebsgrenzen
703	Grundwerkstoffe Messwerk
704	Messwerk
705	Gemessener Wert
706	Parallelverschiebung
707	Filter
708	Alarmverhalten
709	Stromgrenzen
710	Alarmstrom
711	Anzeige-Einstellung
712	Display-Skalierung
713	Drucksensor
714	Temperatursensor
715	Ausgang wird simuliert
716	Eingang wird simuliert
717	Physical device identification
718	Device Write Lock
719	Beobachten
720	Observe Values
721	Trend Values
722	Trend
723	Select the parameter for trending:
724	TrendselectionByte
725	Loop Current
726	Pressure-DP
727	Sensor Temperature
728	Scaled Output
729	strip_gauge_selection_Byte
730	Bar Graph
731	Analog Meter
732	Analog Output
733	Skalierter Ausgang
734	Benutzer bearbeiten Kurve
735	bearbeiten Kurve
736	Customer Specific Curve
737	Displays the Customer specific Input points,Output points
738	No.
739	X-value in %
740	Y-value in %
741	X0 Val
742	7.3f
743	X1 Val
744	X2 Val
745	X3 Val
746	X4 Val
747	X5 Val
748	X6 Val
749	X7 Val
750	X8 Val
751	X9 Val
752	X10 Val
753	X11 Val
754	X12 Val
755	X13 Val
756	X14 Val
757	X15 Val
758	X16 Val
759	X17 Val
760	X18 Val
761	X19 Val
762	X20 Val
763	X21 Val
764	Y0 Val
765	Y1 Val
766	Y2 Val
767	Y3 Val
768	Y4 Val
769	Y5 Val
770	Y6 Val
771	Y7 Val
772	Y8 Val
773	Y9 Val
774	Y10 Val
775	Y11 Val
776	Y12 Val
777	Y13 Val
778	Y14 Val
779	Y15 Val
780	Y16 Val
781	Y17 Val
782	Y18 Val
783	Y19 Val
784	Y20 Val
785	Y21 Val
786	Load curve from device
787	Save curve to device
788	Create a new curve and save it to device
789	User Curve
790	Input Pressure
791	Output
792	Diagnose
793	Overview
794	OK Es gibt keine aktiven Alarme sind im Gerät
795	Ausfall Aufgrund einer Funktionsstörung im Feldgerät oder an seiner Peripherie ist das Ausgangssignal ungültig.
796	Funktionskontrolle Am Feldgerät wird gearbeitet, das Ausgangssignal ist daher vorübergehend ungültig (z.B. eingefroren).
797	Außerhalb der Spezifikation Vom Gerät durch Selbstüberwachung ermittelte Abweichungen von den zulässigen Umgebungs- oder Prozessbedingungen oder Störungen im Gerät selbst weisen darauf hin, dass die Messunsicherheit bei Sensoren oder Sollwertabweichung bei Aktoren wahrscheinlich größer ist als unter Betriebsbedingungen zu erwarten.
798	Wartungsbedarf Das Ausgangssignal ist zwar noch gültig, aber der Abnutzungsvorrat wird demnächst erschöpft oder aufgrund von Einsatzbedingungen eine Funktion in Kürze eingeschränkt sein, z. B. Alterung der pHElektrode.
799	Übersicht
800	Possible Cause: There could be a bad or broken connection between sensor and electronics and/or a mechanical damage to the sensor.Loss of fill fluid from the cell,ruptured diaphragm..
801	Suggested Action: The device must be replaced.
802	Fehler Messwerk-Temperatur
803
804	P-dP außerhalb der Grenzwerte
805
806
807	Possible Cause: The Sensor data/coefficients in the sensor memory are corrupted precluding the correct functionality of the device.
808	Suggested Action: The device must to be replaced.
809	Analog Output Saturated
810
811
812
813	Suggested Action : A DAC (digital to output converter) trimming should be performed and if the error persists consider to replace the device.
814	Possible Cause: The operator could have enabled the input simulation of one or more device variables for testing purposes but, at the end, forgot to return it back to the normal condition disabling the Input simulation condition.
815	Suggested Action: Use a HART configurator (DTM - Hand held) in order to: 1. Recognize in detail which of the three is under simulation condition. 2.to place device back into normal operating mode (Disable the input simulation). Otherwise just power off/on the device in order to disable the input simulation.
816
817	Suggested Action : Use a HART configurator (DTM - Hand held) to place device back in to normal .
818	Max. Arbeitsdruck überschritten
819	Possible Cause: The selected transmitter and/or the process connection elements are not adequate for the specific process conditions.
820	Suggested Action: The compatibility of the pressure transmitter model with process conditions must be checked and, if necessary, replace the instrument with another having the correct characteristics.
821	Messwerktemperatur außerhalb der Grenzwerte
822	Possible Cause : The temperature of the process environment affects the pressure transmitter.In some situation, the device installation could be the cause of a sensor overheating.
823	Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked.It could be required to perform a new sensor trimming or device replacement.A different installation type could be also considered/ required e.g. use of remote seals.
824	Electronic Temperature out of Limit
825	Possible Cause : This condition could be due to the circuitry for the sampling of the temperature that has failed or due to the transmitter installation e.g.steam leakage directed on to transmitter housing, or critical ambiental conditions.
826	Suggested Action : If necessary, use a HART configurator in order to know in detail of which limit (high or low) the Electronic temperature is beyond. Check the transmitter installation to identify possible cause of the abnormal measured temperature and take possible actions to minimize the temperature impact/influence like to insulate the device from the external temperature influence.
827	Fehler im stromausfallsicheren Speicher
828	Possible Cause : Writings to the Sensor non-Volatile Memory was not successful.
829	Suggested Action : The Sensor should be replaced as soon as possible.
830	Fehler Elektronisch-Temperatur
831	Possible cause: The circuitry for the sampling of the electronics temperature has failed..
832	Suggested actions: The device should be replaced as soon as possible.
833	Possible Cause: If the power supply is close to the highest limit very probably it is due to a not correct external power supply while if the power supply is close to the lowest limit, it could be due to a defective or not adequate External power supply or anomalous voltage drop on the loop i.e. too long or not correct wires.
834	Suggested Action: Check the Voltage at the terminal block and if it is not within the valid range check the external power supply or the loop.
835	Konfiguration geändert
836	Mögliche Ursache: Ein Schreibzugriff auf das Gerät hat die Konfiguration geändert
837	Vorgeschlagene Aktion: Klicke auf 'Ruecksetzen Konfiguration geändert' Button für das Löschen des 'Konfiguration geändert' Bits
838	NAMUR NE107
839	OK No Active Alarm exists
840	Diagnose status
841	CheckFunction
842	OffSpecification
843	OK
844	erhalten Gesundheitszustand
845	Maintenance
846	HART Seriennummer
847	Seriennummer bezogen auf das Protokoll
848	Kennzeichen
849	Eindeutige Bezeichnung des Gerätes in der Anlage
850	Beschreibung
851	Zusatzinformation
852	Eingabefeld zur freien Verfügung
853	Gerät
854	Name des Gerätetyps
855	Hersteller
856	Für das Gerät verantwortliches Unternehmen (Name)
857	Schreibschutz
858	Für Datensatz oder Gerät
859	Geräte-Revision
860	Revision des Feldgerätes
861	HART-Revision
862	Hauptprotokollrevision implementiert im Gerät
863	Adresse
864	Geräteadresse in der Anwendung.
865	Langkennz.(Long tag)
866	Langkennzeichen: Eindeutige Bezeichnung des Gerätes in der Anlage
867	Endmontagenummer
868	Änderungszähler
869	Anzahl der Zeiten der Konfiguration des Gerätes hat sich geändert
870	Geräte Profil
871	PV % range
872	QR Code
873	Enter Access Code
874	?????????
875	Flag
876	Incorrect
877	CP
878	Diag.
879	Special Setting
880	Validate Access code
881	Validate Service Personnel Access Code
882	Access Logout
883	Validate Channel Partner Access Code
884	Enter Information
885	QR Code Configuration
886	Service Personnel Information
887	Set Low Range
888	Set Upper Range
889	Prozessvariable auf Null setzen
890	Freigabe Setzen Prozessvariable = 0,0
891	Set PV Val
892	Freigabe des Betriebs mit neuer Prozessvariablen
893	PV Bias Reset
894	PV Scaling Reset method - P-dP Bias will be Reset
895	Enable Parallel Shift operation
896	Rücksetzen Gerät
897	Die Warmstart-Konfiguration wird nicht verändert, das Gerät fährt wieder hoch
898	Rücksetzen auf Feineinstellung User-Messwerk
899	Konfiguration auf Vorgabewerte rücksetzen
900	Geräteparameter auf ihre Vorgabewerte rücksetzen (nicht die Adresse)
901	Konfiguration geändert
902	Flag Gerätekonfiguration geändert rücksetzen
903	Als Feineinstellung User-Messwerk speichern
904	Save the actual sensor trimming as User Trimming
905	Konfiguration als Vorgabewert speichern
906	Die aktuelle Gerätekonfiguration wird als Vorgabewert-Konfiguration gespeichert
907	Messwerk-Feineinstellung auf Werkseinstellungen rücksetzen
908	Messwerk-Feineinstellung auf Werkseinstellungen rücksetzen
909	Ausgangs-Feineinstellung auf Werkseinstellungen rücksetzen
910	Feineinstellung D/A-Wandlerausgang auf Werkseinstellungen rücksetzen
911	Aborting Input Simulation
912	n
913	Seriennummer
914	Eindeutige Seriennummer
915	Hardware Revision
916	Feldgeräterevision
917	Software Revision
918	Feldgeräterevision
919	Messwerksrevision
920	More Info
921	More Information Available:Electronic Temperature
922	More Information Available:Analog output
923	More Information Available: input simulation
924	More Info:
925	More Information Available:Power supply warning
926	More Information Available:P-dP sensor fail
927	More Information Available:Sensor temperature fail
928	More Information Available:Electronic temperature fail
929	More Information Available:P-dP Out of limit
930	More Information Available:Sensor temperature Out of limit
931	More Information Available:Sensor memory fail
932	More Information Available:Sensor non-volatile memory burn error
933	More Information Available:Max working pressure exceeded
934	More Information Available:Loop test
935	More Information Available:Output readback fail
936	Hours
937	sec
938	Clear Other Diag Simulation
939	Change SV Mapping
940	Change TV Mapping
941	Change QV Mapping
942	P-dP
943	Elektronische Temperatur
944	Simulate
945	Pressure Simulation
946	Sensor Temp. Simulation
947	Aborting Simulation
948	Zero trim
949	Full trim
950	Sensor Temperature Trimming
951	Seriennummer des Sensors
952	Eindeutige Seriennummer des Sensors
953	Sensor serial Number
954	Refresh Page
955	Enable/Disable diagnostics QR Code
956	Refresh
957	Click on this button to refresh the UI
958	Set New PV
959	Offset rücksetzen
960	Freigabe Rücksetzen des Offset = 0,0
961	Set Parallel Shift
962	Ausführung der Parallelverschiebung
963	Druck Simulation
964	Simulation Value
965	statischer Druck Simulation
966	Messwerkstemperatur Simulation
967	Ausführen
968	Sensor Temperature Simulation
969	Bereich 4-20mA
970	Bereich 4-20mA
971	Change polling address and loop current mode
972	Local_DeviceSerialNumber
973	Device State
974	Funktionsprüfung
975	Außerhalb der Spezifikation
976	Wartungsbedarf
977	Fehler
978	Span
979	Process Value %
980	Object for CMD 1283
981	Physikalische Einheit für den Prozessdruck
982	Device type
983	Pxx100
984	Linearization type
985	Minimum Span
986	PDP Sensor High Limit
987	PDP Sensor Low Limit
988	Possible Cause :There could be a bad or broken connection between sensor and electronics and/or a mechanical damage to the sensor.Loss of fill fluid from the cell,ruptured diaphragm.. Suggested Action :The device must be replaced..
989	Possible Cause :The circuitry for the sampling of the temperature has failed.. Suggested Action :The device must be replaced.
990	Possible Cause :The circuitry for the sampling of the electronics temperature has failed. Suggested Action :The device should be replaced as soon as possible.
991	Possible Cause :The measurement range has not been correctly calculated OR an incorrect transducer model has been selected. Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked. Probably a different transmitter type is required..
992	Possible Cause :The temperature of the process environment affects the pressure transmitter.In some situation, the device installation could be the cause of a sensor overheating. Suggested Action :The compatibility of pressure transmitter model and process conditions has to be checked.It could be required to perform a new sensor trimming or device replacement.A different installation type could be also considered/ required e.g. use of remote seals..
993	Possible Cause :The Sensor data/coefficients in the sensor memory are corrupted precluding the correct functionality of the device. Suggested Action :The device must to be replaced.
994	Electronic memory fail
995	Possible Cause :EMC problems like electrostatic discharge (ESD), burst, surge outside the specification limits and/or soft errors (ionic radiation) could corrupt memory data.. Suggested Action :The Device must to be replaced.Or, the database must to be reloaded.
996	Electronics NV-memory Burn Error
997	Possible Cause :The device could have been powered off immediately after the modification of the data that was not fully written in the NV-memory. Suggested Action :The device should be replaced as soon as possible.
998	Possible Cause :Writings to the Sensor non-Volatile Memory was not successful. Suggested Action :The Sensor should be replaced as soon as possible.
999	Possible Cause :The selected transmitter and/or the process connection elements are not adequate for the specific process conditions. Suggested Action :The compatibility of the pressure transmitter model with process conditions must be checked and, if necessary, replace the instrument with another having the correct characteristics..
1000	Possible Cause :The analog and digital analog outputs for the Primary Variable are held at the requested value. Device is in fixed current (Loop Test) mode. Suggested Action :Use a HART configurator to place device back into normal operating mode (Remove from Loop Test - Fixed output mode).
1001	Possible Cause :The applied/measured pressure is beyond the configured working range represented by the Low and High range values. Suggested Action :
1002	Possible Cause :The output circuit could be broken or not correctly calibrated. Suggested Action :A DAC (digital to output converter) trimming should be performed and if the error persists consider to replace the device.
1003	Possible Cause :This condition could be due to the circuitry for the sampling of the temperature that has failed or due to the transmitter installation e.g.steam leakage directed on to transmitter housing, or critical ambiental conditions. Suggested Action :If necessary, use a HART configurator in order to know in detail of which limit (high or low) the Electronic temperature is beyond. Check the transmitter installation to identify possible cause of the abnormal measured temperature and take possible actions to minimize the temperature impact/influence like to insulate the device from the external temperature influence.
1004	Active Alert
1005	Device state
1006	Status Group
1007	Electronics
1008	HW Status: Electronics
1009	Sensor
1010	HW Status: Sensor
1011	Configuration or Installation
1012	Operating Condition
1013	Power Supply
1014	Operating Condition - Power Supply
1015	Process
1016	Operating Condition - Process
1017	Cmd 48 byte 17
1018	Cmd 48 byte 18
1019	Cmd 48 byte 19
1020	Cmd 48 byte 20
1021	Cmd 48 byte 21
1022	Cmd 48 byte 22
1023	Cmd 48 byte 23
1024	spezielle Kurve
1025	PdP
1026	Pressure - Differential Pressure
1027	Status
1028	Limit Status
1029	Pres Fmly stat
1030	classification
1031	device Family
1032	Pdp USL
1033	Pdp LSL
1034	Pdp Minimum Span
1035	7d
1036	Damp an irregular signal
1037	Dämpfung
1038	.1f
1039	Simulation status
1040	Disable
1041	Enable
1042	Alarm mit Analogausgang
1043	Ausgang im Fehlerfall
1044	Size
1045	Acquisition Period
1046	pdpSensor_units
1047	Minimum value for range limits
1048	Untere Messbereichsgrenze
1049	Maximum value for range limits
1050	Obere Messbereichsgrenze
1051	Minimum difference between URV and LRV
1052	Kleinste Spanne
1053	Sensor1 trim support
1054	Linearity
1055	Die Messwerkstemperatur wird in dieser Einheit angezeigt
1056	Temperatureinheit
1057	Sensor Temperature Damping
1058	Sensor Temperature Minimum Span
1059	Sensor Temperature Trim Value
1060	sensor1 trim high
1061	electronicTemperatureValue_units
1062	Electronic Temperature Damping
1063	Elect. Temperature Minimum Span
1064	Electronic Temp. Collection
1065	communicationScaleOutValue_units
1066	communicationScaleOutValue Damping
1067	Scaled Output Minimum Span
1068	ScaledOutput Collection
1069	Cal.Pressure
1070	Calibration Pressure
1071	Download to device
1072	Upload from device
1073	Squawk Control
1074	Off
1075	On
1076	Squawk once
1077	squawk_abort_label
1078	Start Squawk
1079	Common Tables
1080	Interoperable *
1081	Universal
1082	Common Practice
1083	Pressure Universal
1084	Pressure Common
1085	Menu
1086	Rosemount Magflow
1087	Rosemount Pressure
1088	Moore Products
1089	Siemens Pressure
1090	P2 Common
1091	PV
1092	Wireless
1093	Munge
1094	Analytical Oxygen/Combustion/Methane/CO
1095	Flow Totalizer - Rate Indicator
1096	Flow Variable Area
1097	Flow Coriolis Mass
1098	Flow Ultrasonic - Gas
1099	Flow Ultrasonic - Liquid
1100	Level Ultrasonic
1101	Level Radar - Microwave
1102	Pressure Absolute
1103	Level Capacitance
1104	Pressure Differential
1105	Level Hydrostatic
1106	Level
1107	Pressure Absolute/Relative
1108	Level Microwave
1109	Level Radar
1110	Level Density - Nuclear
1111	Flow Electromagnetic
1112	Flow Vortex
1113	Flow Magmeter - Rack Version
1114	Flow High Performance Magmeter
1115	Flow Mass
1116	Flow Ultrasonic
1117	Flow Magnetic
1118	Flow Magnetic - Custody Transfer
1119	Flow 2-wire Magnetic
1120	Flow Coriolis Mass - Custody Transfer
1121	Flow 2-wire Vortex
1122	Flow Thermal
1123	Temperature Head Mounted
1124	Temperature Compact
1125	Temperature DIN Rail Mounted
1126	Analytical pH
1127	Analytical Conductivity - Conductive
1128	Analytical Conductivity - Inductive
1129	Temperature Sensor
1130	Level Servo
1131	Temperature DIN Rail
1132	Temperature
1133	Analytical ORP
1134	Analytical pION
1135	Analytical IConc
1136	Analytical Electrode Conductivity
1137	Analytical Toroidal Conductivity
1138	Valve Positioner
1139	Valve Controller
1140	Pressure
1141	Pressure Multivariable
1142	Analytical pH/ORP
1143	Flow Coriolis
1144	Analytical Conductivity
1145	Valve Positioner/Pneumatic
1146	Valve Actuator - Electrical
1147	Temperature Dual Input
1148	Valve Actuator
1149	Analytical Corrosion
1150	Analytical Density - Nuclear
1151	Level Continuous Gamma
1152	Level Laser Ranging
1153	Pressure Safety
1154	Flow Vortex/Swirl
1155	Flow
1156	Analytical 4 Electrode Conductivity
1157	Analytical 2 Electrode Conductivity
1158	Analytical Troidal Conductivity
1159	Analytical pH/ORP/pIon/Ion Conc
1160	Analytical Oxygen
1161	Pressure P, dP + Multivariable
1162	Temperature 2-wire
1163	Pressure w/ PID
1164	Pressure Saturated Steam
1165	Analytical Density - Gamma Ray
1166	Level Gamma Ray
1167	Analytical Weight - Gamma Ray
1168	Level w/ Density - Gamma Ray
1169	Analytical Motorized Density
1170	Flow Multivariable Mass
1171	Temperature Multivariable
1172	Specialty HART-to-Analog Signal Conv
1173	Flow dP
1174	Pressure Low Power
1175	Pressure Certified SIL2
1176	Interoperable
1177	Analytical Density
1178	Valve Positioner/Electropneumatic
1179	Flow Magnetic Inductive
1180	Analytical
1181	Analytical Opacity Monitor
1182	Analytical Oxygen/Combustion
1183	Analytical 2-wire Conductivity
1184	Analytical 2-wire Conductivity w/ pure H20
1185	Analytical 2-wire Conductivity w/ % conc
1186	Analytical 2-wire Oxygen/Chlorine/Ozone
1187	Analytical 2-wire pH/ORP
1188	Analytical 2-wire Contacting/Toroidal
1189	Analytical Oxygen - High Temperature
1190	Analytical Conductivity w/ % conc
1191	Analytical pH/ORP/ISE
1192	Analytical Amperometric Analyzer
1193	Analytical Dual Input Analyzer
1194	Pressure Pressure/Level
1195	Analytical Consistency
1196	Analytical Microwave-Pulp Consistency
1197	Analytical Microwave Consistency
1198	Valve Digital Positioner
1199	Valve Smart Valve Positioner
1200	Temperature Differential
1201	Analytical Dissolved Oxygen
1202	Analytical pH Controller
1203	Analytical Conductivity/Resistivity Controller
1204	Analytical Conductivity/Resistivity
1205	Level Displacement
1206	Temperature w/ PID
1207	Valve Universal Positioner
1208	Level Radar - Reflex
1209	Pressure Gauge
1210	Pressure Sealed Gauge
1211	Valve Digital Positioner w/ PID
1212	Valve Intelligent Positioner
1213	Analytical Gas Detector
1214	Analytical Infrared Gas Detector
1215	Analytical Electrochemical Gas Detector
1216	Analytical Measuring Instruments
1217	Level Magnostrictive
1218	Valve On/Off Valve Controller
1219	Level Radar - Pulse
1220	Level Continuous Capactive
1221	Valve Damper Actuator
1222	Valve Electric Damper Actuator
1223	Flow Electronic
1224	Flow Vortex - Multiparameter Mass
1225	Analytical UV Flame Detector
1226	Analytical UVIR Flame Detector
1227	Analytical IR Flame Detector
1228	Analytical Fire Detector
1229	Analytical Gas Detector Display Interface
1230	Analytical Toxic Gas Detector
1231	Analytical Flame Detector
1232	Level Nuclear
1233	Analytical Microwave
1234	Analytical Density - Radiometric
1235	Level Radiometric
1236	Analytical Gas/Steam
1237	Level Nucleonic
1238	Analytical Blade Consistency
1239	Analytical Rotary Consistency
1240	Pressure Absolute/Differential
1241	Positioner
1242	Analytical Combustible Gas Detector
1243	Analytical Point Infrared Gas Detector
1244	Analytical Multi-Detector Monitor System
1245	Valve Positioner/Electro-hydraulic
1246	Valve Monitor
1247	Enable on token-passing data link layer only
1248	Enable on TDMA data link layer only
1249	Enable on both TDMA and token-passing data link layer
1250	WirelessHART Device
1251	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
1252	Primary
1253	Primary Analog Channel
1254	Secondary
1255	Secondary Analog Channel
1256	Tertiary
1257	Tertiary Analog Channel
1258	Quaternary
1259	Quaternary Analog Channel
1260	Quinary
1261	Quinary Analog Channel
1262	Critical Power Failure
1263	Lock all
1264	Trim not supported
1265	Configuration cannot be changed
1266	Locked by gateway
1267	Analog Input Channel
1268	Analog Output Channel
1269	Secondary Analog Channel Saturated
1270	Tertiary Analog Channel Saturated
1271	Quaternary Analog Channel Saturated
1272	Quinary Analog Channel Saturated
1273	Secondary Analog Channel Fixed
1274	Tertiary Analog Channel Fixed
1275	Quaternary Analog Channel Fixed
1276	Quinary Analog Channel Fixed
1277	Simulation active
1278	The device is in simulation mode and the level output is not representative of the process.
1279	Non-Volatile memory failure
1280	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
1281	Volatile memory error
1282	The RAM memory check is invalid or maybe corrupt
1283	Watchdog reset executed
1284	A watchdog reset has been performed
1285	Voltage conditions out of range
1286	A voltage condition is outside its allowable range
1287	Environmental conditions out of range
1288	An internal or environmental condition is beyond acceptable limits.
1289	Electronic failure
1290	A hardware problem not related to the sensor has been detected.
1291	Subdevice list changed
1292	Duplicate master detected
1293	Capacity Denied
1294	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
1295	Bandwidth allocation pending
1296	Block transfer pending
1297	Continuous
1298	The Burst Message is published continuously at (worst case) the Minimum Update Period.
1299	Window
1300	The Burst Message is triggered when the source value deviates more than the specified trigger value
1301	Rising
1302	The Burst Message is triggered when source value Rises Above the specified trigger value.
1303	Falling
1304	The Burst Message is triggered when the source value Falls Below the specified trigger value.
1305	On-change
1306	The Burst Message is triggered when any value in the message changes.
1307	Battery life
1308	Percent range
1309	Loop current
1310	Primary variable
1311	Secondary variable
1312	Tertiary variable
1313	Quaternary variable
1314	Enable event notification on token-passing data link layer
1315	Enable event notification on TDMA data link layer
1316	Enable event notification on TDMA and token-passing data link layer
1317	Configuration changed event pending
1318	Device status event pending
1319	More status available event pending
1320	Enable single data point trending
1321	Enable filtered trending
1322	The sample is filtered using a time constant equal to one-third the trend sample period
1323	Enable average trending
1324	The value obtained by dividing the sum of all samples in the period by the total number of samples
1325	Read receive time
1326	Write date and time
1327	Non-Volatile Clock
1328	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
1329	Clock Uninitialized
1330	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
1331	Line Power
1332	Device is powered via a hardwired connection to a plant power source.
1333	Battery Power
1334	Device operates solely of its (internal) battery.
1335	Recharg.B./Power Sc.
1336	Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat).
1337	Idle
1338	Active search
1339	Looking for neighbors.
1340	Negotiating
1341	Quarantined
1342	Operational
1343	Suspended
1344	Deep sleep
1345	Ultra-low power
1346	Wireless Signal Found
1347	Network packets have been recognized
1348	Wireless Signal Identified
1349	Wireless Time Synchronized
1350	WirelessHart Signal Identified
1351	Network Admission Requested
1352	Set on transmission of first join request
1353	Join Retrying
1354	Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started.
1355	Join Failed
1356	Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search.
1357	Network Security Clearance Granted
1358	Network Manager Session Established
1359	Network Joined
1360	Network Joined. Normal superframe and links obtained.
1361	Network Bandwidth Requested
1362	Negotiating Network Properties. Gateway session obtained.
1363	Join Complete
1364	Normal operating mode.
1365	No restrictions
1366	SI Only
1367	Restricted to SI Unit codes only
1368	Open - accept all devices
1369	Use Whitelist for access
1370	Use Blacklist
1371	Use Whitelist and Blacklist
1372	Lockdown - disable join links
1373	Process automation device
1374	Discrete device
1375	Hybrid:Process automation+discrete
1376	I/O System
1377	WirelessHART Process automation device
1378	WirelessHART Discrete device
1379	WirelessHART Process automation+discrete
1380	WirelessHART Gateway
1381	WirelessHART Access point
1382	WirelessHART Process adapter
1383	WirelessHART Discrete adapter
1384	WirelessHART enabled handheld/portable maintenance tool
1385	Don't attempt to join
1386	Join now
1387	Attempt to join immediately on powerup or reset
1388	US
1389	United States of America
1390	JP
1391	Japan
1392	DE
1393	Germany
1394	FR
1395	France
1396	ES
1397	Spain
1398	RU
1399	Russian Federation
1400	CN
1401	People's Republic of China
1402	Nominal
1403	Device Power Status is nominal
1404	Low
1405	Device Power Status is low
1406	Critically Low
1407	Device Power Status is critically low
1408	Recharging - Low
1409	Recharging - High
1410	Secondary Master
1411	Primary Master
1412	PV Analog Channel Saturated
1413	PV Analog Channel Fixed
1414	Device Profile
1415	Device Diagnostic Status 0
1416	Device Diagnostic Status 1
1417	I/O and Subdevice Status
1418	WirelessHART Status
1419	Time Set Option
1420	Real Time Clock Flags
1421	Country
1422	Country of intended device installation
1423	SI Unit Control
1424	Indicates if device should only display SI unit codes
1425	Burst Trigger Units
1426	Burst Trigger Class
1427	Wired HART Enabled
1428	Enabled on Wired HART device connection only
1429	Wireless HART Enabled
1430	Enabled on WirelessHART device connection only
1431	Both Wired and WirelessHart Enabled
1432	Enabled on both Wired and WirelessHART connections
1433	Burst Msg Trigger Mode
1434	Event Status
1435	Event Notification Control
1436	Operate mode Mask
1437	Not Defined
1438	Power Source
1439	Power source of the device
1440	Wireless Mode
1441	Join Status
1442	The current location in the joining sequence of operations.
1443	Network Access Mode
1444	Join Mode
1445	Power Status
1446	Power status of the device
1447	Master Mode
1448	This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode.
1449	Trend Units
1450	Trend Device Variable Unit Code
1451	Trend Classification
1452	Trend Device Variable Classification
1453	Trend Control
1454	Device Status Mask
1455	Ext dev status Mask
1456	Device Diagnostic Status 0 Mask
1457	Device Diagnostic Status 1 Mask
1458	Device Diagnostic Status 2 Mask
1459	Device Diagnostic Status 3 Mask
1460	AO saturated Mask
1461	AO fixed Mask
1462	Latched Device Status
1463	Latched Ext dev status
1464	Latched Operate Mode
1465	Latched Device Diagnostic Status 0
1466	Latched Device Diagnostic Status 1
1467	Latched Device Diagnostic Status 2
1468	Latched Device Diagnostic Status 3
1469	Latched AO saturated
1470	Latched AO fixed
1471	Wireless Module Device Type
1472	Device type of the Wireless Radio
1473	Wireless Module Manufacturer ID
1474	Manufacturer of the Wireless Radio contained in this device
1475	Subdevice Device Type
1476	Device type of the subdevice attached to this system.
1477	Subdevice Manufacturer Id
1478	Manufacturer of the subdevice attached to this system.
1479	Time Stamp
1480	Relative time value on network
1481	8u
1482	Dynamic Variables Returned for Device Variables
1483	Command Response Truncated
1484	Configuration Change Counter Mismatch
1485	Status bytes mismatch
1486	Device Variable
1487	Variable to trim
1488	8.3f
1489	Number of points in the Device is -> %{pdp_TAB_ACTUAL_NUMBER}
1490	Upload in progress, please wait...
1491	All X-Y values read from device !!
1492	We are about to create a new linearisation curve. Please take care of following points to save a new curve successfully in the device 1) X/Y value pair must be monotonously incremented 2) First value of X/Y pair must be 0/0 3) Last value of X/Y pair must be 100/100 Continue ?
1493	Yes;No
1494	Select no of points (X/Y pairs) to be entered
1495	2;3;4;5;6;7;8;9;10;11;12;13;14;15;16;17;18;19;20;21;22
1496	X0 Value
1497	x0
1498	Y0 Value
1499	y0
1500	X1 Value
1501	x1
1502	Y1 Value
1503	y1
1504	X2 Value
1505	x2
1506	Y2 Value
1507	y2
1508	X3 Value
1509	x3
1510	Y3 Value
1511	y3
1512	X4 Value
1513	x4
1514	Y4 Value
1515	y4
1516	X5 Value
1517	x5
1518	Y5 Value
1519	y5
1520	X6 Value
1521	x6
1522	Y6 Value
1523	y6
1524	X7 Value
1525	x7
1526	Y7 Value
1527	y7
1528	X8 Value
1529	x8
1530	Y8 Value
1531	y8
1532	X9 Value
1533	x9
1534	Y9 Value
1535	y9
1536	X10 Value
1537	x10
1538	Y10 Value
1539	y10
1540	X11 Value
1541	x11
1542	Y11 Value
1543	y11
1544	X12 Value
1545	x12
1546	Y12 Value
1547	y12
1548	X13 Value
1549	x13
1550	Y13 Value
1551	y13
1552	X14 Value
1553	x14
1554	Y14 Value
1555	y14
1556	X15 Value
1557	x15
1558	Y15 Value
1559	y15
1560	X16 Value
1561	x16
1562	Y16 Value
1563	y16
1564	X17 Value
1565	x17
1566	Y17 Value
1567	y17
1568	X18 Value
1569	x18
1570	Y18 Value
1571	y18
1572	X19 Value
1573	x19
1574	Y19 Value
1575	y19
1576	X20 Value
1577	x20
1578	Y20 Value
1579	y20
1580	X21 Value
1581	x21
1582	Y21 Value
1583	y21
1584	Select
1585	Continue;Re-enter no of x/y pairs
1586	Result :%[L]{pdp_TAB_STATUS} -> %{pdp_TAB_STATUS}
1587	Click on 'Load curve from device' button to load the curve from device
1588	CP331896
1589	SV2317113
1590	Access Code is verified.
1591	Incorrect Access Code.
1592	Enter information
1593	disp_string2
1594	Aborting procedure due to last error.
1595	PV value read PV : %{0}%{1}
1596	Set PV Zero;Ready
1597	Aborting procedure due to last error
1598	PV value read PV: %{0}%{1}
1599	Set PV Value;Ready
1600	Enter new PV value:
1601	P-dP Bias will be Reset
1602	OP :%{2}% PV :%{0}%{1} URV and LRV will be shifted. Continue?
1603	Enter new OP percent val:
1604	Applied values read: PV: %{1} %{0}
1605	Applied zero reads: PV: %{1}%{0}
1606	Device will perform warm startup.After the end of this operation it may be necessary to reconnect the device. Continue?
1607	The Sensor Trimming is set to the User trimming! Actual settings are lost. Continue?
1608	The Device is set to default setting! Actual settings are lost.After the end of this operation it may be necessary to reconnect the device. Continue?
1609	Configuration Changed Flag reset is complete
1610	The Actual Sensor Trimming is Saved as User Trimming! Continue?
1611	The Actual device settings is Saved as Default setting! Continue?
1612	The Sensor Trimming parameters are set to the factory settings! User specific settings are lost. Continue?
1613	The Output Trimming parameters are set to the factory settings! User specific settings are lost. Continue?
1614	Simulate Presure Value;Simulate Sensor Temperature Value;Exit
1615	Enter the Pressure Simulation Value
1616	Enter the Sensor Temperature Simulation Value
1617	Device Serial No:%{0}%{1}%{2}000000000%{4}
1618	Device Serial No:%{0}%{1}%{2}00000000%{4}
1619	Device Serial No:%{0}%{1}%{2}0000000%{4}
1620	Device Serial No:%{0}%{1}%{2}000000%{4}
1621	Device Serial No:%{0}%{1}%{2}00000%{4}
1622	Device Serial No:%{0}%{1}%{2}0000%{4}
1623	Device Serial No:%{0}%{1}%{2}000%{4}
1624	Device Serial No:%{0}%{1}%{2}00%{4}
1625	Device Serial No:%{0}%{1}%{2}0%{4}
1626	Device Serial No:%{0}%{1}%{2}%{4}
1627	Hardware Version:0%{0}.0%{1}.0%{2}
1628	Software Version:0%{0}.0%{1}.0%{2}
1629	Messwerksrevision:0%{0}.0%{1}.0%{2}
1630	Electronic Temperature out Of Low Limit
1631	Electronic Temperature out Of High Limit
1632	Electronic Temperature out Of Low Limit Electronic Temperature out Of High Limit
1633	Analog Output Low Saturated
1634	Analog Output High Saturated
1635	Analog Output Low Saturated Analog Output High Saturated
1636	P-dP Simulation aktiv
1637	Statische Drucksimulation aktiv
1638	Messwerk-Temperatursimulation aktiv
1639	P-dP Simulation aktiv Statische Drucksimulation aktiv
1640	P-dP Simulation aktiv Messwerk-Temperatursimulation aktiv
1641	Statische Drucksimulation aktiv Messwerk-Temperatursimulation aktiv
1642	P-dP Simulation aktiv Statische Drucksimulation aktiv Messwerk-Temperatursimulation aktiv
1643	Stromversorgung zu niedrig
1644	Netzteil zu hoch
1645	Stromversorgung zu niedrig Netzteil zu hoch
1646	SV is:
1647	TV is:
1648	QV is:
1649	Art der Verriegelung
1650	Permanent verriegelt;Zeitweise verriegelt;Alles verriegelt
1651	Pressure value simulation disabled.
1652	Please enter the value to simulate
1653	Pressure value simulated.
1654	Select choice:
1655	Simulate;Exit;
1656	Sensor Temperature value simulated.
1657	Simulate ;Exit;
1658	Last Input val used: Hival: %{2}%{0} Loval: %{1}%{0}
1659	High Trim;Low Trim;Display limits;Exit
1660	Apply a loval Pres. Lower than Hival
1661	Pressure stabilizing. PLEASE WAIT...
1662	Pres. applied: %{1}%{0}
1663	Enter lower trim value
1664	Apply a Hival Pres. Higher than Loval
1665	Enter upper trim value
1666	SENSOR LIMITS: USL: %{2}%{0} LSL: %{1}%{0}
1667	CALIBRATION: URV: %{5}%{3} LRV: %{4}%{3}
1668	Sensor temperature read: : %{1}%{0}
1669	Last Input val used : Val: %{1}%{0}
1670	Enter the reference Temperature
1671	a
1672	b
1673	c
1674	Sensor Serial No:
1675	00000%{4}
1676	0000%{4}
1677	000%{4}
1678	00%{4}
1679	0%{4}
1680	%{4}
1681	%{4} Incorrect number!
1682	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}00000%{snsrSerialNo_Part4}
1683	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}0000%{snsrSerialNo_Part4}
1684	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}000%{snsrSerialNo_Part4}
1685	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}00%{snsrSerialNo_Part4}
1686	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}0%{snsrSerialNo_Part4}
1687	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}%{snsrSerialNo_Part4}
1688	Sensor Serial No:%{a}%{snsrSerialNo_Part0}%{b}%{snsrSerialNo_Part1}%{c}%{snsrSerialNo_Part2}%{d}%{snsrSerialNo_Part3}%{snsrSerialNo_Part4} Incorrect number!
1689
1690	e
1691	00000
1692	0000
1693	000
1694	00
1695	invalid
1696	Refreshing page...
1697	Refresh action complete.
1698	Diagnostics QR Code status is updated
1699	.
1700
1701	000000000
1702	00000000
1703	0000000
1704	000000
1705	Enter new PV
1706	Now Apply input pressure URV:%{0} %{2} LRV:%{1} %{2}
1707	Current process value: %{0} %{1}
1708	Continue read value;Set as 4mA value;Set as 20mA value;Exit
1709	Set polling address
1710	iPoll
1711	Polling address selected is greater than 0. Please select loop current mode. Recommended to disable loop current mode.
1712	Polling address selected is 0. Please select loop current mode. Recommended to enable loop current mode.
1713	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000000000%{Local_DeviceSerialNumber}
1714	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00000000%{Local_DeviceSerialNumber}
1715	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0000000%{Local_DeviceSerialNumber}
1716	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000000%{Local_DeviceSerialNumber}
1717	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00000%{Local_DeviceSerialNumber}
1718	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0000%{Local_DeviceSerialNumber}
1719	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}000%{Local_DeviceSerialNumber}
1720	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}00%{Local_DeviceSerialNumber}
1721	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}0%{Local_DeviceSerialNumber}
1722	Device Serial No:%{serialNo_Part0}%{serialNo_Part1}%{serialNo_Part2}%{Local_DeviceSerialNumber}
1723	Device failed to accept Setpoint TabOpCode == 1 (New Operation)
1724	X%{q} Value %
1725	Y%{q} Value %
1726	Writing table data to device
1727	Device failed to accept Setpoint TabOpCode == 2 (Last Value)
1728	Squawk in progress..
1729	Do you want to end squawk?
Reference ID	String