HART设备字典

Loading…

引用ID	字符串
0	Error status
1	OK
2	Help
3	Ultrasonic signal too large. Amplifier overload.
4	Ultrasonic signal too small. Check ultrasonic sensor connection.
5	Wall thickness exceeds measurement range.
6	Thickness under range. Minimum thickness – 3mm.
7	Battery voltage low. Replace battery.
8	Averaging failure.
9	Memory not cleared. Power control failure.
10	Parameter outside expected range.
11	Sensor Board Failed To Respond.
12	Back Wall Echo too small. Improve sensor bonding to pipe.
13	Front Wall Echo too small or late arrival. Retry measurement. Potential sensor problem
14	Warning status
15	Observation #0: Electromagnetic or acoustic interference detected.. Move cabling away from potential noise source, Contact 3-Sci if persists.
16	Warning #1: Signal energy between echoes. Potential sensor damage or metal thickness below system minimum. Validate via Full Waveform or contact 3-Sci
17	Warning #2: Early arrival of front wall echo. Possible hardware problem or transmitter configured for different sensor type.
18	Warning #3: Late arrival of front wall echo. Possible hardware problem or transmitter configured for different sensor type
19	Observation #4: Increased 'Measurement Uncertainty' value. Calculation method discrepancy. Optionally validate via Full Waveform.
20	Observation #5: Gain at minimum level
21	Observation #6: Small amplitude of primary echo in relation to secondary echo. Increased 'Measurement Uncertainty' value.
22	Observation #7: Primary echo amplitude smaller than ideal. Monitor 'Measurement Uncertainty' value for increases.
23	Observation #8: Two back wall echoes or slopes are of comparable magnitude. Lowest thickness recorded. Monitor 'Measurement Uncertainty' value for increases
24	Observation #9: Two primary echoes or slopes are of comparable magnitude. Monitor 'Measurement Uncertainty' value for increases..
25	Warning #10: Amplification setting saturated primary echo. Retry measurement.
26	Warning #11: Small front wall echo. Retry measurement.
27	Observation #12: Small back wall echo indicates imperfect adhesive or clamped installation. Increased measurement uncertainty
28	Observation #13: Large variation in averaged thicknesses, indicative of a poor adhesive bond. Increased 'Measurement Uncertainty' value.
29	Warning #14: Temperature of pipe outside of operational range
30	Observation #15: Measurement technique – Back Wall Echo Multiple.
31	Warning #16: Wireless unit operational temperature range exceeded
32	Warning #17: External Temperature Probe not connected
33	.3f
34	8.3f
35	System verification indicator damping value
36	Measurement uncertainty damping value
37	Pipe thickness damping value
38	Pipe temperature damping value
39	AGC value damping value
40	AGC tries damping value
41	Calculated speed of sound damping value
42	First pulse arrival time damping value
43	Front wall echo arrival time damping value
44	Back wall echo arrival time damping value
45	First pulse magnitude damping value
46	Back wall echo magnitude damping value
47	Ambient temperature damping value
48	Charge used data damping value
49	Readings counter damping value
50	Echo ratio damping value
51	7d
52	System verification indicator sensor serial number
53	Measurement uncertainty sensor serial number
54	Pipe thickness sensor serial number
55	Pipe temperature sensor serial number
56	AGC value sensor serial number
57	AGC tries sensor serial number
58	Calculated speed of sound sensor serial number
59	First pulse arrival time sensor serial number
60	Front wall echo arrival time sensor serial number
61	Back wall echo arrival time sensor serial number
62	First pulse magnitude sensor serial number
63	Back wall echo magnitude sensor serial number
64	Ambient temperature sensor serial number
65	Charge used data sensor serial number
66	Readings counter sensor serial number
67	Echo ratio sensor serial number
68	System verification indicator lower sensor limit
69	Measurement uncertainty lower sensor limit
70	Pipe thickness lower sensor limit
71	Pipe temperature lower sensor limit
72	AGC value lower sensor limit
73	AGC tries lower sensor limit
74	Calculated speed of sound lower sensor limit
75	First pulse arrival time lower sensor limit
76	Front wall echo arrival time lower sensor limit
77	Back wall echo arrival time lower sensor limit
78	First pulse magnitude lower sensor limit
79	Back wall echo magnitude lower sensor limit
80	Ambient temperature lower sensor limit
81	Charge used data lower sensor limit
82	Readings counter lower sensor limit
83	Echo ratio lower sensor limit
84	System verification indicator upper sensor limit
85	Measurement uncertainty upper sensor limit
86	Pipe thickness upper sensor limit
87	Pipe temperature upper sensor limit
88	AGC value upper sensor limit
89	AGC tries upper sensor limit
90	Calculated speed of sound upper sensor limit
91	First pulse arrival time upper sensor limit
92	Front wall echo arrival time upper sensor limit
93	Back wall echo arrival time upper sensor limit
94	First pulse magnitude upper sensor limit
95	Back wall echo magnitude upper sensor limit
96	Ambient temperature upper sensor limit
97	Charge used data upper sensor limit
98	Readings counter upper sensor limit
99	Echo ratio upper sensor limit
100	System verification indicator minimum span
101	Measurement uncertainty minimum span
102	Pipe thickness minimum span
103	Pipe temperature minimum span
104	AGC value minimum span
105	AGC tries minimum span
106	Calculated speed of sound minimum span
107	First pulse arrival time minimum span
108	Front wall echo arrival time minimum span
109	Back wall echo arrival time minimum span
110	First pulse magnitude minimum span
111	Back wall echo magnitude minimum span
112	Ambient temperature minimum span
113	Charge used data minimum span
114	Readings counter minimum span
115	Echo ratio minimum span
116	System verification indicator family status
117	Measurement uncertainty family status
118	Pipe thickness family status
119	Pipe temperature family status
120	AGC value family status
121	AGC tries family status
122	Calculated speed of sound family status
123	First pulse arrival time family status
124	Front wall echo arrival time family status
125	Back wall echo arrival time family status
126	First pulse magnitude family status
127	Back wall echo magnitude family status
128	Ambient temperature family status
129	Charge used data family status
130	Readings counter family status
131	Echo ratio family status
132	System verification indicator limit status
133	Measurement uncertainty limit status
134	Pipe thickness limit status
135	Pipe temperature limit status
136	AGC value limit status
137	AGC tries limit status
138	Calculated speed of sound limit status
139	First pulse arrival time limit status
140	Front wall echo arrival time limit status
141	Back wall echo arrival time limit status
142	First pulse magnitude limit status
143	Back wall echo magnitude limit status
144	Ambient temperature limit status
145	Charge used data limit status
146	Readings counter limit status
147	Echo ratio limit status
148	System verification indicator process data status
149	Measurement uncertainty process data status
150	Pipe thickness process data status
151	Pipe temperature process data status
152	AGC value process data status
153	AGC tries process data status
154	Calculated speed of sound process data status
155	First pulse arrival time process data status
156	Front wall echo arrival time process data status
157	Back wall echo arrival time process data status
158	First pulse magnitude process data status
159	Back wall echo magnitude process data status
160	Ambient temperature process data status
161	Charge used data process data status
162	Readings counter process data status
163	Echo ratio process data status
164	System verification indicator device variable classification codes
165	Measurement uncertainty device variable classification codes
166	Pipe thickness device variable classification codes
167	Pipe temperature device variable classification codes
168	AGC value device variable classification codes
169	AGC tries device variable classification codes
170	Calculated speed of sound device variable classification codes
171	First pulse arrival time device variable classification codes
172	Front wall echo arrival time device variable classification codes
173	Back wall echo arrival time device variable classification codes
174	First pulse magnitude device variable classification codes
175	Back wall echo magnitude device variable classification codes
176	Ambient temperature device variable classification codes
177	Charge used data device variable classification codes
178	Readings counter device variable classification codes
179	Echo ratio device variable classification codes
180
181	System verification indicator
182	Measurement uncertainty
183	Pipe thickness
184	Pipe temperature
185	AGC value
186	AGC tries
187	Calculated speed of sound
188	First pulse arrival time
189	Front wall echo arrival time
190	Back wall echo arrival time
191	First pulse magnitude
192	Back wall echo magnitude
193	Ambient temperature
194	Charge used data
195	Readings counter
196	Echo ratio
197	Download Variables
198	Upload Variables
199	Operate
200	Basic
201	Advanced
202	Device Settings
203	Information
204	HART Details
205	Wireless Details
206	Software Details
207	Manufacturing Details
208	3-Sci
209	Diagnostics
210	Device Status
211	Measurement Status
212	Device Information
213	Standard
214	Maintenance
215	Services
216	Calibration
217	Operations
218	Network
219	Join Key
220	Offline
221	Data
222	HART
223	Wi-Corr Bond
224	Get Health Status
225	Switch Write Protect
226	Common Tables
227	Interoperable *
228	Universal
229	Common Practice
230	Pressure Universal
231	Pressure Common
232	Menu
233	Rosemount Magflow
234	Rosemount Pressure
235	Moore Products
236	Siemens Pressure
237	P2 Common
238	PV
239	Wireless
240	Munge
241	Analytical Oxygen/Combustion/Methane/CO
242	Flow Totalizer - Rate Indicator
243	Flow Variable Area
244	Flow Coriolis Mass
245	Flow Ultrasonic - Gas
246	Flow Ultrasonic - Liquid
247	Level Ultrasonic
248	Level Radar - Microwave
249	Pressure Absolute
250	Level Capacitance
251	Pressure Differential
252	Level Hydrostatic
253	Level
254	Pressure Absolute/Relative
255	Level Microwave
256	Level Radar
257	Level Density - Nuclear
258	Flow Electromagnetic
259	Flow Vortex
260	Flow Magmeter - Rack Version
261	Flow High Performance Magmeter
262	Flow Mass
263	Flow Ultrasonic
264	Flow Magnetic
265	Flow Magnetic - Custody Transfer
266	Flow 2-wire Magnetic
267	Flow Coriolis Mass - Custody Transfer
268	Flow 2-wire Vortex
269	Flow Thermal
270	Temperature Head Mounted
271	Temperature Compact
272	Temperature DIN Rail Mounted
273	Analytical pH
274	Analytical Conductivity - Conductive
275	Analytical Conductivity - Inductive
276	Temperature Sensor
277	Level Servo
278	Temperature DIN Rail
279	Temperature
280	Analytical ORP
281	Analytical pION
282	Analytical IConc
283	Analytical Electrode Conductivity
284	Analytical Toroidal Conductivity
285	Valve Positioner
286	Valve Controller
287	Pressure
288	Pressure Multivariable
289	Analytical pH/ORP
290	Flow Coriolis
291	Analytical Conductivity
292	Valve Positioner/Pneumatic
293	Valve Actuator - Electrical
294	Temperature Dual Input
295	Valve Actuator
296	Analytical Corrosion
297	Analytical Density - Nuclear
298	Level Continuous Gamma
299	Level Laser Ranging
300	Pressure Safety
301	Flow Vortex/Swirl
302	Flow
303	Analytical 4 Electrode Conductivity
304	Analytical 2 Electrode Conductivity
305	Analytical Troidal Conductivity
306	Analytical pH/ORP/pIon/Ion Conc
307	Analytical Oxygen
308	Pressure P, dP + Multivariable
309	Temperature 2-wire
310	Pressure w/ PID
311	Pressure Saturated Steam
312	Analytical Density - Gamma Ray
313	Level Gamma Ray
314	Analytical Weight - Gamma Ray
315	Level w/ Density - Gamma Ray
316	Analytical Motorized Density
317	Flow Multivariable Mass
318	Temperature Multivariable
319	Specialty HART-to-Analog Signal Conv
320	Flow dP
321	Pressure Low Power
322	Pressure Certified SIL2
323	Interoperable
324	Analytical Density
325	Valve Positioner/Electropneumatic
326	Flow Magnetic Inductive
327	Analytical
328	Analytical Opacity Monitor
329	Analytical Oxygen/Combustion
330	Analytical 2-wire Conductivity
331	Analytical 2-wire Conductivity w/ pure H20
332	Analytical 2-wire Conductivity w/ % conc
333	Analytical 2-wire Oxygen/Chlorine/Ozone
334	Analytical 2-wire pH/ORP
335	Analytical 2-wire Contacting/Toroidal
336	Analytical Oxygen - High Temperature
337	Analytical Conductivity w/ % conc
338	Analytical pH/ORP/ISE
339	Analytical Amperometric Analyzer
340	Analytical Dual Input Analyzer
341	Pressure Pressure/Level
342	Analytical Consistency
343	Analytical Microwave-Pulp Consistency
344	Analytical Microwave Consistency
345	Valve Digital Positioner
346	Valve Smart Valve Positioner
347	Temperature Differential
348	Analytical Dissolved Oxygen
349	Analytical pH Controller
350	Analytical Conductivity/Resistivity Controller
351	Analytical Conductivity/Resistivity
352	Level Displacement
353	Temperature w/ PID
354	Valve Universal Positioner
355	Level Radar - Reflex
356	Pressure Gauge
357	Pressure Sealed Gauge
358	Valve Digital Positioner w/ PID
359	Valve Intelligent Positioner
360	Analytical Gas Detector
361	Analytical Infrared Gas Detector
362	Analytical Electrochemical Gas Detector
363	Analytical Measuring Instruments
364	Level Magnostrictive
365	Valve On/Off Valve Controller
366	Level Radar - Pulse
367	Level Continuous Capactive
368	Valve Damper Actuator
369	Valve Electric Damper Actuator
370	Flow Electronic
371	Flow Vortex - Multiparameter Mass
372	Analytical UV Flame Detector
373	Analytical UVIR Flame Detector
374	Analytical IR Flame Detector
375	Analytical Fire Detector
376	Analytical Gas Detector Display Interface
377	Analytical Toxic Gas Detector
378	Analytical Flame Detector
379	Level Nuclear
380	Analytical Microwave
381	Analytical Density - Radiometric
382	Level Radiometric
383	Analytical Gas/Steam
384	Level Nucleonic
385	Analytical Blade Consistency
386	Analytical Rotary Consistency
387	Pressure Absolute/Differential
388	Positioner
389	Analytical Combustible Gas Detector
390	Analytical Point Infrared Gas Detector
391	Analytical Multi-Detector Monitor System
392	Valve Positioner/Electro-hydraulic
393	Valve Monitor
394	Enable on token-passing data link layer only
395	Enable on TDMA data link layer only
396	Enable on both TDMA and token-passing data link layer
397	WirelessHART Device
398	IEEE 802.15.4 2.4GHz DSSS with O-QPSK Modulation
399	Primary
400	Primary Analog Channel
401	Secondary
402	Secondary Analog Channel
403	Tertiary
404	Tertiary Analog Channel
405	Quaternary
406	Quaternary Analog Channel
407	Quinary
408	Quinary Analog Channel
409	Critical Power Failure
410	Lock all
411	Trim not supported
412	Configuration cannot be changed
413	Locked by gateway
414	Analog Input Channel
415	Analog Output Channel
416	Secondary Analog Channel Saturated
417	Tertiary Analog Channel Saturated
418	Quaternary Analog Channel Saturated
419	Quinary Analog Channel Saturated
420	Secondary Analog Channel Fixed
421	Tertiary Analog Channel Fixed
422	Quaternary Analog Channel Fixed
423	Quinary Analog Channel Fixed
424	Simulation active
425	The device is in simulation mode and the level output is not representative of the process.
426	Non-Volatile memory failure
427	The Non-Volatile memory check is invalid or maybe corrupt, or the battery of a battery-backed memory has failed.
428	Volatile memory error
429	The RAM memory check is invalid or maybe corrupt
430	Watchdog reset executed
431	A watchdog reset has been performed
432	Voltage conditions out of range
433	A voltage condition is outside its allowable range
434	Environmental conditions out of range
435	An internal or environmental condition is beyond acceptable limits.
436	Electronic failure
437	A hardware problem not related to the sensor has been detected.
438	Subdevice list changed
439	Duplicate master detected
440	Capacity Denied
441	The device was unable to acquire the communication bandwidth required to support the Burst Messaging specified
442	Bandwidth allocation pending
443	Block transfer pending
444	Continuous
445	The Burst Message is published continuously at (worst case) the Minimum Update Period.
446	Window
447	The Burst Message is triggered when the source value deviates more than the specified trigger value
448	Rising
449	The Burst Message is triggered when source value Rises Above the specified trigger value.
450	Falling
451	The Burst Message is triggered when the source value Falls Below the specified trigger value.
452	On-change
453	The Burst Message is triggered when any value in the message changes.
454	Battery life
455	Percent range
456	Loop current
457	Primary variable
458	Secondary variable
459	Tertiary variable
460	Quaternary variable
461	Off
462	Enable event notification on token-passing data link layer
463	Enable event notification on TDMA data link layer
464	Enable event notification on TDMA and token-passing data link layer
465	Configuration changed event pending
466	Device status event pending
467	More status available event pending
468	Disable
469	Enable single data point trending
470	Enable filtered trending
471	The sample is filtered using a time constant equal to one-third the trend sample period
472	Enable average trending
473	The value obtained by dividing the sum of all samples in the period by the total number of samples
474	Read receive time
475	Write date and time
476	Non-Volatile Clock
477	When set the device contains a battery-backed clock. In this case, the clock does not need to be reset if there is a power failure.
478	Clock Uninitialized
479	The real-time clock has never been set with the date and time. For example, the clock is volatile and power was removed from and restored to the device.
480	Line Power
481	Device is powered via a hardwired connection to a plant power source.
482	Battery Power
483	Device operates solely of its (internal) battery.
484	Recharg.B./Power Sc.
485	Rechargeable battery power or power scavenging. The device has a short-term supply of energy (must be at least one hour) that is continuously being replenished. The device's power is being replenished by harvesting and converting energy from the environment surrounding the device (e.g. solar, vibration, heat).
486	Idle
487	Active search
488	Looking for neighbors.
489	Negotiating
490	Quarantined
491	Operational
492	Suspended
493	Deep sleep
494	Ultra-low power
495	Wireless Signal Found
496	Network packets have been recognized
497	Wireless Signal Identified
498	Wireless Time Synchronized
499	WirelessHart Signal Identified
500	Network Admission Requested
501	Set on transmission of first join request
502	Join Retrying
503	Set after the first join request retry (i.e. when number of join requests > 2). Cleared when device is authenticated or when Active Search started.
504	Join Failed
505	Set on transition from Active Search mode to Deep Sleep mode. Cleared on transition from Deep Sleep to Active Search.
506	Network Security Clearance Granted
507	Network Manager Session Established
508	Network Joined
509	Network Joined. Normal superframe and links obtained.
510	Network Bandwidth Requested
511	Negotiating Network Properties. Gateway session obtained.
512	Join Complete
513	Normal operating mode.
514	None
515	No restrictions
516	SI Only
517	Restricted to SI Unit codes only
518	Open - accept all devices
519	Use Whitelist for access
520	Use Blacklist
521	Use Whitelist and Blacklist
522	Lockdown - disable join links
523	Process automation device
524	Discrete device
525	Hybrid:Process automation+discrete
526	I/O System
527	WirelessHART Process automation device
528	WirelessHART Discrete device
529	WirelessHART Process automation+discrete
530	WirelessHART Gateway
531	WirelessHART Access point
532	WirelessHART Process adapter
533	WirelessHART Discrete adapter
534	WirelessHART enabled handheld/portable maintenance tool
535	Don't attempt to join
536	Join now
537	Attempt to join immediately on powerup or reset
538	US
539	United States of America
540	JP
541	Japan
542	DE
543	Germany
544	FR
545	France
546	ES
547	Spain
548	RU
549	Russian Federation
550	CN
551	People's Republic of China
552	Nominal
553	Device Power Status is nominal
554	Low
555	Device Power Status is low
556	Critically Low
557	Device Power Status is critically low
558	Recharging - Low
559	Recharging - High
560	Secondary Master
561	Primary Master
562	PV Analog Channel Saturated
563	PV Analog Channel Fixed
564	Device Profile
565	Device Diagnostic Status 0
566	Device Diagnostic Status 1
567	I/O and Subdevice Status
568	WirelessHART Status
569	Time Set Option
570	Real Time Clock Flags
571	Country
572	Country of intended device installation
573	SI Unit Control
574	Indicates if device should only display SI unit codes
575	Burst Trigger Units
576	Burst Trigger Class
577	Wired HART Enabled
578	Enabled on Wired HART device connection only
579	Wireless HART Enabled
580	Enabled on WirelessHART device connection only
581	Both Wired and WirelessHart Enabled
582	Enabled on both Wired and WirelessHART connections
583	Burst Msg Trigger Mode
584	Event Status
585	Event Notification Control
586	Operate mode Mask
587	Not Defined
588	Power Source
589	Power source of the device
590	Wireless Mode
591	Join Status
592	The current location in the joining sequence of operations.
593	Network Access Mode
594	Join Mode
595	Power Status
596	Power status of the device
597	Master Mode
598	This sets the I/O System's Data Link Layer operation on all channels as either primary or secondary master mode.
599	Trend Units
600	Trend Device Variable Unit Code
601	Trend Classification
602	Trend Device Variable Classification
603	Trend Control
604	Device Status Mask
605	Ext dev status Mask
606	Device Diagnostic Status 0 Mask
607	Device Diagnostic Status 1 Mask
608	Device Diagnostic Status 2 Mask
609	Device Diagnostic Status 3 Mask
610	AO saturated Mask
611	AO fixed Mask
612	Latched Device Status
613	Latched Ext dev status
614	Latched Operate Mode
615	Latched Device Diagnostic Status 0
616	Latched Device Diagnostic Status 1
617	Latched Device Diagnostic Status 2
618	Latched Device Diagnostic Status 3
619	Latched AO saturated
620	Latched AO fixed
621	Wireless Module Device Type
622	Device type of the Wireless Radio
623	Wireless Module Manufacturer ID
624	Manufacturer of the Wireless Radio contained in this device
625	Subdevice Device Type
626	Device type of the subdevice attached to this system.
627	Subdevice Manufacturer Id
628	Manufacturer of the subdevice attached to this system.
629	Time Stamp
630	Relative time value on network
631	8u
632	Dynamic Variables Returned for Device Variables
633	Command Response Truncated
634	Configuration Change Counter Mismatch
635	Status bytes mismatch
636	Device Variable
637	Key 1
638	First key word for joining wirless network
639	08X
640	Key 2
641	Second key word for joining wireless network
642	Key 3
643	Third key word for joining wireless network
644	Key 4
645	Fourth key word for joining wireless network
646	Neighbor Count
647	Number of available neighbors.
648	Advertisement Count
649	Number of Advertisement packets received.
650	Join Attempts
651	Number of Join Attempts. Too many join attempts will result in the device considering the join failed.
652	Join Retry Timer
653	The Join Retry Timer indicates the amount of time since the last join request was sent.
654	5.3f
655	Network Search Time
656	The Network Search Timer indicates the amount of time listening for first advertisement.
657	Minimum time a device must stay in active search mode when forced to join a newtork
658	Shed Time
659	Adv. Period
660	Advertising period
661	Advertised Neighbors Number
662	Number of neighbors advertising in addition to this device.
663	Network ID
664	Network Tag
665	The network tag is a proxy for the Network Id so that the network can be identified in a text form at the application level.
666	Peak packets/s
667	Peak packets per second.
668	Peak packet load
669	Duration at peak packet load before power drained. Must be at least one hour (set to 24 hours if not applicable)
670	Recover time
671	Time to recover from power drain (set to zero if not applicable). While recovering, the device must be able to route 1 packet per second.
672	Keep-alive time
673	Minimum required keep-alive time.
674	Receive signal level
675	RSL (receive signal level in dB) threshold 'good' connection.
676	dBm
677	Max Neighbors
678	Maximum number of neighbors
679	Max Packetbuffer
680	Maximum number of packet buffers
681	Battery Life Remaining
682	Remaining battery life
683	Days
684	Generated packets
685	Number of packets generated by this device
686	Terminated packets
687	Number of packets terminated by this device
688	DLL failures
689	Number of Data-Link Layer MIC failures detected
690	NL(Session) failures
691	Number of Network Layer (Session) MIC failures detected
692	CRC errors
693	Number of CRC errors detected.
694	Nonce Counter Values
695	Number of nonce counter values not received. This value is incremented for each zero in nonce counter history that underflows.
696	Device Nickname Address
697	The 2-byte nickname is assigned and managed by the Network Manager. Consequently, it is only locally unique (i.e., within the network the device belongs to).
698	Output Power
699	Wireless Module Device Revision
700	Wireless Module Software Revision
701	Wireless Module Hardware Revision
702	Key change failed
703	Request declined
704	Force join declined
705	Network ID change pending
706	Invalid network ID
707	Write Protect is disabled, do you want to enable it?
708	Write Protect is enabled, do you want to disable it?
引用ID	字符串