Loading…
Loading…
名称 | ID | 标签 | 描述 | 类型 | 访问 | 分类 |
---|---|---|---|---|---|---|
setpoint_value | 4000 | Setpoint | Refers to the requested position in terms of percent. | 读 | 浮点 | 10 |
position_value | 4001 | Position | Refers to the actual valve position in terms of percent. | 读 | 浮点 | 10 |
pressure_value | 138E | Pressure | Refers to the output pressure of OUT 1 of the positioner in terms of percent. | 读 | 浮点 | 10 |
setpoint_units | 4002 | Setpoint Units | 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 | 读/写 | 枚举 | 8 |
position_units | 4003 | Position Units | 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 | 读 | 枚举 | 8 |
pressure_units | 138D | Pressure Units | 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 | 读 | 枚举 | 8 |
sensor_units | 4004 | Sensor Units | 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 | 读 | 枚举 | 8 |
range_units | 4005 | 主变量范围单位 | 现场设备变量单位——使用数值表示、最小范围、范围上限、范围下限、传感器上限和传感器下限显示的工程单位。 | 读 | 枚举 | 8 |
analog_alarm_code | 4006 | 模拟量输出报警类型 | 模拟量输出报警类型——定义当现场设备检测到模拟量输出可能未跟踪关联现场设备变量时模拟量输出响应的方式。注意——数值表示可能不确定。 | 读 | 枚举 | 64 |
input_analog_value | 4007 | Input I | Refers to the requested position in terms of current in mA. | 读 | 浮点 | 66 |
output_analog_value | 4008 | Output I | Refers to the actual valve position in terms of current in mA. | 读 | 浮点 | 66 |
damping_val | 4009 | 主变量阻尼 | 阻尼值——同时应用至各自模拟量输出的数值表示和模拟值的阻尼时间常数。该变量的单位始终为秒钟。 | 读 | 浮点 | 8 |
input_upper_value | 400A | FS In | Refers to the input current to move the valve to full open / close position in normal / reverse operation. | 读 | 浮点 | 32 |
input_lower_value | 400B | Zero In | Refers to the input current to move the valve to full open / close position in normal / reverse operation. | 读 | 浮点 | 32 |
output_upper_value | 400C | FS Out | Refers to the output current when the valve is at full open / close position in normal / reverse operation. | 读 | 浮点 | 32 |
output_lower_value | 400D | Zero Out | Refers to the output current when the valve is at full open / close position in normal / reverse operation. | 读 | 浮点 | 32 |
sensor_serial_number | 400E | Sensor Serial | 传感器序列号——识别数值表示或现场设备变量来源的传感器。 | 读 | 无符号 | 32 |
min_sensor_span | 400F | Min_Sensor_Span | 最小范围值——定义上限值和下限值之间允许的最小差。 | 读 | 浮点 | 32 |
flow_type | 4014 | Flow Type | The positioner supports Linear, Quick Opening, and Equal Percentage flow types. | 读/写 | 枚举 | 32 |
reserved_1 | 4015 | 读/写 | 整型 | 1025 | ||
limit_enbl | 4016 | Limit Control | Limit the valve travel in certain region specified by upper and lower limits. | 读/写 | 枚举 | 1025 |
control_mode | 2772 | Control Mode | Control the valve in either normal or reverse acting mode. | 读/写 | 枚举 | 1025 |
flop_mode | 4017 | Display Mode | Show %closed or %open on positioner display. | 读/写 | 枚举 | 1025 |
digital_setpoint_mode | 4018 | Digital Mode | When enabled, the positioner will ignore 4 to 20 mA input signal, and allows control to be applied digitaly. | 读/写 | 枚举 | 1025 |
cutoff_mode | 4019 | Cutoff Mode | When enabled, the positioner will apply a larger than necessary close control signal to the valve | 读/写 | 枚举 | 1025 |
名称 | ID | 标签 | 描述 | 类型 | 访问 | 分类 |