变量名称： alarm_integer_19

变量ID： 0x429A

变量标签： 报警数

变量描述： This parameter is the number of the alarm. For example, 26 for alarm A26 and 42 for alarm A102.

变量处理： 读

变量分类： 本地

变量长度： 1

变量数据类型： 枚举

变量枚举值	变量枚举文本
0x0000	A000: Undefined
0x0001	A001: EEprom Checksum Error (Core Processor)
0x0002	A002: RAM Test Error (Core Processor)
0x0003	A003: Sensor Not Responding (No Tube Interrupt)
0x0004	A004: Temperature Sensor Out-of-Range
0x0005	A005: Input Over-Range
0x0006	A006: Transmitter Not Characterized
0x0007	A007: Real-Time Interrupt Failure
0x0008	A008: Density Outside Limits
0x0009	A009: Transmitter Initializing/Warming Up
0x000A	A010: Calibration Failure
0x000B	A011: Excess Calibration Correction, Zero too Low
0x000C	A012: Excess Calibration Correction, Zero too High
0x000D	A013: Process too Noisy to Perform Auto Zero
0x000E	A014: Transmitter Failed
0x000F	A015: MA Readback Error
0x0010	A016: Line RTD Temperature Out-Of-Range
0x0011	A017: Meter RTD Temperature Out-Of-Range
0x0012	A018: (E)EPROM Checksum Error (Model 3000)
0x0013	A019: RAM Test Error (Model 3000)
0x0014	A020: Calibration Factors Unentered
0x0015	A021: Unrecognized/Unentered Sensor Type
0x0016	A022: (E)EPROMConfig. DB Corrupt (Core Processor)
0x0017	A023: (E)EPROMTotals Corrupt (Core Processor)
0x0018	A024: (E)EPROMProgram Corrupt (Core Processor)
0x0019	A025: Protected Boot Sector Fault
0x001A	A026: Sensor/Xmtr Communication Error
0x001B	A027: Security Breach
0x001C	A028: Sensor/Xmtr Communication Failure
0x001D	A029: Internal Communication failure
0x001E	A030: Hardware/software incompatible
0x001F	A031: Undefined
0x0020	A032: Meter Verification Fault Alarm
0x0021	A033: Sensor OK / Tubes Stopped by Process (A33)
0x0022	A034: Undefined
0x0023	A035: Undefined
0x0024	A036: Undefined
0x0025	A037: Undefined
0x0026	A038: Undefined
0x0027	A039: Undefined
0x0064	A100: Primary mA Output Saturated
0x0065	A101: Primary mA Output Fixed
0x0066	A102: Drive Over-Range / Partially Full Tube
0x0067	A103: Data Loss Possible
0x0068	A104: Calibration-In-Progress
0x0069	A105: Slug Flow
0x006A	A106: Burst Mode Enabled
0x006B	A107: Power Reset Occurred
0x006C	A108: Event #1 Triggered
0x006D	A109: Event #2 Triggered
0x006E	A110: Frequency Output Saturated
0x006F	A111: Frequency Output Fixed
0x0070	A112: Series 3000 Software Upgrade Recommended
0x0071	A113: Secondary mA Output Saturated
0x0072	A114: Secondary mA Output Fixed
0x0073	A115: External Input Error
0x0074	A116: API Temperature Out-of-Limits
0x0075	A117: API Density Out-of-Limits
0x0076	A118: Discrete Output 1 Fixed
0x0077	A119: Discrete Output 2 Fixed
0x0078	A120: ED: Unable to fit curve data
0x0079	A121: ED: Extrapolation alarm
0x007A	A122: Discrete Output 3 Fixed
0x007B	A123: Discrete Output 4 Fixed
0x007C	A124: Frequency Input Saturated
0x007D	A125: Batcher: Timeout
0x007E	A126: Batcher: Overrun
0x007F	A127: Batcher: Start without reset
0x0080	A128: Batcher: Start not OK
0x0081	A129: Undefined
0x0082	A130: Printer: Paper Out
0x0083	A131: Meter Verification Info Alarm
0x0084	A132: Simulation Mode Active
0x0085	A133: Undefined
0x0086	A134: Undefined
0x0087	A135: Undefined
0x0088	A136: Undefined
0x0089	A137: Undefined
0x008A	A138: Undefined
0x008B	A139: Undefined

变量显示格式：

变量编辑格式：

变量单位：

变量最大值： N/A

变量最小值： N/A

变量读取命令列表

无

变量写入命令列表

无