Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| ramc_self_test | 402E | Self test | Commands the RAMC electronic to perform a selftest. Reports any errors that occured. | msrc_UNKNOWN | Details |
| write_enable_10min | 4028 | Enable wrt 10min | msrc_UNKNOWN | Details | |
| change_to_new_password | 4029 | New password | msrc_UNKNOWN | Details | |
| err_abort_without_func_key_disp | 409D | Aborting | msrc_UNKNOWN | Details | |
| normal_exit_for_chg_passwd | 409E | Exiting | msrc_UNKNOWN | Details | |
| ramc_reset_URV_LRV | 4030 | Reset URV/LRV | Perform a device rerange by applying the factory Upper Range Value and Lower Range Values to the device input. | msrc_UNKNOWN | Details |
| ramc_temp_clear | 4094 | Clear values | Copies the logged values to 'Old time/value', clears the values and resets the temperature to the actual value. | msrc_UNKNOWN | Details |
| ramc_flow_clear | 4097 | Clear values | Clears the logged values and resets the warning bits. | msrc_UNKNOWN | Details |
| ramc_monitor_clear | 409B | Reset power fail | Resets power fail warning bit. This bit is set automatically after power up. | msrc_UNKNOWN | Details |
| ramc_clear_all_warns | 402D | Reset all errors | Resets all pending error bits | msrc_UNKNOWN | Details |
| ramc_reset_man_cal_table | 418A | Reset adjustment table | Resets the manual adjustment table to factory settings. | msrc_UNKNOWN | Details |
| ramc_start_autozero | 4098 | Start autozero | Press F4 to start Autozero recognition. It will take 90 sec to complete. | msrc_UNKNOWN | Details |
| ramc_master_reset | 4181 | Master reset | All parameter settings are reset to factory settings. | msrc_UNKNOWN | Details |
| ramc_total_reset | 4185 | Total reset | Perform a totalizer reset. | msrc_UNKNOWN | Details |
| warning_mancal_message | 4084 | Manual adjustment | Changing the Manual Adjustment Points will result in a new output behavior of the RAMC. | msrc_UNKNOWN | Details |
| ramc_man_cal_on_off | 4088 | Activate/deactiv | Start/Stop Manual Adjustment Function. As a result the manual adjustment table is active and the flow is shown only in the percent unit (Refer also to Instruction Manual). | msrc_UNKNOWN | Details |
| ramc_set_adjust_point | 4189 | Set adjustm. point | Select the appropriate adjustment point in the list and press OK (Refer also to Instruction Manual). | msrc_UNKNOWN | Details |
| ramc_reset_cfg_chng_flg | 4182 | Reset Cfg chng flag | Reset Configuration changed flag | msrc_UNKNOWN | Details |
| setRealtimeClock | 4188 | Set Real-time Clock | msrc_UNKNOWN | Details | |
| refreshTrendData | 419D | Refresh Trend Data | msrc_UNKNOWN | Details | |
| clearEventData | 419B | Clear Event Data | msrc_UNKNOWN | Details | |
| readEventData | 419A | Read Event Data | msrc_UNKNOWN | Details | |
| ramc_makeItSquawk | 4180 | Squawk | Make the Field Device Squawk- This causes the device to visually, audibly or mechanically alert to allow technicans to idendify it | msrc_UNKNOWN | Details |
| method_set_burst_trigger_1 | 4190 | Set Burst 1 Trigger | msrc_UNKNOWN | Details | |
| method_set_burst_trigger_2 | 4193 | Set Burst 2 Trigger | msrc_UNKNOWN | Details | |
| method_set_burst_trigger_3 | 4196 | Set Burst 3 Trigger | msrc_UNKNOWN | Details | |
| method_set_burst_trigger | 41A3 | msrc_UNKNOWN | Details | ||
| method_set_burst_period_1 | 418F | Set Burst 1 Period | msrc_UNKNOWN | Details | |
| method_set_burst_period_2 | 4192 | Set Burst 2 Period | msrc_UNKNOWN | Details | |
| method_set_burst_period_3 | 4195 | Set Burst 3 Period | msrc_UNKNOWN | Details | |
| method_set_burst_period | 41A4 | msrc_UNKNOWN | Details | ||
| applied_rerange | 1007 | Apply URV/LRV | Applied values- Perform a device rerange by applying the desired Upper Range Value and Lower Range Values to the device input | msrc_UNKNOWN | Details |
| warning_message | 1017 | Set loop to manual | msrc_UNKNOWN | Details | |
| device_master_reset | 1072 | Device reset | Device Reset- Commands the electronics to perform a reset. This is equivalent to cycling the power off and then back on to the field device. | msrc_UNKNOWN | Details |
| transmitter_loop_test | 1023 | Loop test | Loop test- Allows the User to manually manipulate the Analog Output to a selected constant output value | msrc_UNKNOWN | Details |
| transmitter_dac_trim | 1024 | D/A trim | Digital to Analog Trim- Allows the calibration of a selected Analog Output with an external reference at the operating endpoints of the Analog Output | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | Leaving fixed crnt mode | Leaving Fixed Current Mode- Takes the Analog Output out of a mode where the output was a constant value, and returns the output to a mode where the output tracks the input | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | Aborting return to normal | msrc_UNKNOWN | Details | |
| lock_unlock_device | 1073 | Lock/Unlock device | Lock/Unlock Device- Places the device in either a locked or unlocked position. | msrc_UNKNOWN | Details |
| Name | ID | Label | Description | Type | Source |