Loading…
Loading…
| Name | ID | Label | Description | Type | Source |
|---|---|---|---|---|---|
| ramc_set_damping | 4034 | Set damping | Damping Value- Damping time constant applied to both the Digital Value representation and Analog Value of the respective Analog Output. The units of this variable are always in seconds. | msrc_UNKNOWN | Details |
| applied_rerange | 1007 | Apply URV/LRV | Applied values- Perform a device rerange by applying the desired Upper Range Value and Lower Range Values to the device input | msrc_UNKNOWN | Details |
| ramc_applied_rerange | 403D | Apply URV value | Applied values- Perform a device rerange by applying the desired Upper Range Value and Lower Range Values to the device input | msrc_UNKNOWN | Details |
| ramc_loop_test | 402A | Loop test | Loop test- Allows the User to manually manipulate the Analog Output to a selected constant output value | msrc_UNKNOWN | Details |
| ramc_dac_trim | 4031 | D/A trim | Digital to Analog Trim- Allows the calibration of a selected Analog Output with an external reference at the operating endpoints of the Analog Output | msrc_UNKNOWN | Details |
| ramc_reset | 402F | Master reset | All parameter settings are reset to factory settings. | msrc_UNKNOWN | Details |
| CW_ramc_total_reset | 4039 | Total reset | Perform a totalizer reset. | msrc_UNKNOWN | Details |
| warning_mancal_message | 4084 | Manual Calibration | Changing the Manual Calibration Points will result in a new output behavior of the RAMC. The values are not resettable. | msrc_UNKNOWN | Details |
| ramc_man_cal_on_off | 4088 | Activate/deactiv | Start/Stop Manual Calibration Function. As a result the manual calibration table is active and the flow is shown only in the percent unit (Refer also to Instruction Manual). | msrc_UNKNOWN | Details |
| ramc_self_test | 402E | Self test | Commands the RAMC electronic to perform a selftest. Reports any errors that occured. | msrc_UNKNOWN | Details |
| write_enable_10min | 4028 | Enable wrt 10min | msrc_UNKNOWN | Details | |
| change_to_new_password | 4029 | New password | msrc_UNKNOWN | Details | |
| err_abort_without_func_key_disp | 409D | Aborting | msrc_UNKNOWN | Details | |
| normal_exit_for_chg_passwd | 409E | Exiting | msrc_UNKNOWN | Details | |
| ramc_reset_URV_LRV | 4030 | Reset URV/LRV | Perform a device rerange by applying the factory Upper Range Value and Lower Range Values to the device input. | msrc_UNKNOWN | Details |
| ramc_temp_clear | 4094 | Clear values | Copies the logged values to 'Old durat/value', clears the values and resets the temperature to the actual value. | msrc_UNKNOWN | Details |
| ramc_flow_clear | 4097 | Clear values | Clears the logged values and resets the warning bits. | msrc_UNKNOWN | Details |
| ramc_monitor_clear | 409B | Reset power fail | Resets power fail warning bit. This bit is set automatically after power up. | msrc_UNKNOWN | Details |
| ramc_clear_all_warns | 402D | Reset all errors | Resets all pending error bits | msrc_UNKNOWN | Details |
| ramc_start_autozero | 4098 | Start autozero | Press F4 to start Autozero recognition. It will take 90 sec to complete. | msrc_UNKNOWN | Details |
| leave_fixed_current_mode | 1003 | Leaving fixed crnt mode | Leaving Fixed Current Mode- Takes the Analog Output out of a mode where the output was a constant value, and returns the output to a mode where the output tracks the input | msrc_UNKNOWN | Details |
| return_to_normal | 1016 | Aborting return to normal | msrc_UNKNOWN | Details | |
| Name | ID | Label | Description | Type | Source |